Transverse Beam Research Articles

Active nonperturbative stabilization of the laser-plasma-accelerated electron beam source

Laser plasma accelerators have the ability to produce high-quality electron beams in compact, all-optical-driven configurations, with the electron beams uniquely suited for a wide variety of accelerator-based applications. However, fluctuations and drifts in the laser delivery to the mm-scale plasma target (the electron beam source) will translate into electron beam source variations that can limit their utility for demanding applications like light sources. Based on previous work in developing a nonperturbative diagnostic for the high-power laser delivery at focus [1], we present a full four-dimensional active-stabilization system for the laser (transverse laser focus position and laser pointing angle in both transverse planes) and experimentally demonstrate how, as a result of the laser stabilization, critical parameters in the electron beam source were stabilized. Through the use of an energy resolved imaging system for the electron beam, we directly monitor the jitter in the transverse electron beam source location. Furthermore, the dispersion in the orthogonal plane to the magnetic spectrometer was recorded for each shot which is tied to the source pointing angle of the electron beam and, in part, driven by the angle of the laser at the interaction point. Our laser stabilization system reduced variation in the electron beam source location from $\ensuremath{\sim}12$ to $3\text{ }\text{ }\mathrm{\ensuremath{\mu}}\mathrm{m}$ and reduced the dispersion jitter of the electron beam by 20%.

Nonlinear finite element investigations on different configurations of exterior beam-column connections with different concrete strengths in column and floor

The fast development of quality concrete production has increased the usage of high-strength concrete (HSC) in the columns of high-rise buildings where high axial column loads exist. In contrast, normal-strength concrete (NSC) is used in the floor system for economic reasons. This produces a weak concrete zone at the intersection of columns and floors. Studies focused on evaluating the performance of such connections are still limited. The current numerical study investigates the performance of such connections. The developed numerical model has been verified against the experimental test for connections with different column-to-beam strengths. The numerical model has demonstrated acceptable accuracy compared to the experimental results. Moreover, the validated model has been employed to investigate the influence of different column-to-floor strengths on connections with and without transverse beams and floor slabs. It has been found that the strength and stiffness of connections with different concrete strengths have been improved compared to monolithic connections. Furthermore, the increase in joint strength and stiffness for connections with different column-to-floor strengths is more pronounced for connections with transverse beams and floor slabs due to their contribution to achieving proper confinement conditions for the weak concrete in the joint zone. In addition, the presence of a transverse beam affects the induced stress of the beam bars, resulting in a change in the mode of failure to beam flexural failure, whereas the presence of a slab floor increases both the stiffness and flexural strength of the beam. However, connections with the floor slab suffered high damage due to the transferred equilibrium torsion. Moreover, connections with different column-to-floor strengths exhibited larger stains in their joint stirrups; hence, additional joint stirrups are recommended to avoid the brittle shear failure of the joint. The study ended by evaluating the response of such connections under high axial column loads. It has been observed that planer connections perform poorly in terms of strength and ductility, while adequate performance has been observed for connections with transverse beams or slabs. Therefore, the role of the transverse beam and slab should be taken into account in the design of the connections with different column-to-floor strengths.

On the energy limit of compact isochronous cyclotrons

Existing analytical models for transverse beam dynamics in isochronous cyclotrons are often not valid or not precise for relativistic energies. The main difficulty in developing such models lies in the fact that cross-terms between derivatives of the average magnetic field and the azimuthally varying components cannot be neglected at higher energies. Taking such cross-terms rigorously into account results in an even larger number of terms that need to be included in the equations. In this paper, a method is developed which is relativistically correct and which provides results that are practical and easy to use. We derive new formulas, graphs and tables for the radial and vertical tunes in terms of the flutter, its radial derivatives, the spiral angle and the relativistic gamma. Using this method, we study the 2νr = N structural resonance (N is number of sectors) and provide formulas and graphs for its stopband. Combining those equations with the new equation for the vertical tune, we find the stability zone and the energy limit of compact isochronous cyclotrons for any value of N. We confront the new analytical method with closed orbit simulations of the IBA C400 cyclotron for hadron therapy.

Current-induced switching of photonic spin Hall effect in a magnetic insulator based on spin–orbit torques

The photonic spin Hall effect (PSHE) is analogous to the electronic spin Hall effect, which has substantial potential for optoelectronic applications. However, PSHE-based devices are rarely studied, and manipulating the PSHE by charge current has remained elusive thus far. In this paper, we demonstrate current-induced switching of PSHE in the Ce1Dy2Al0.42Fe4.58O12 thin film capping with Pt electrodes, which is mediated by spin–orbit torques at the Pt/Ce1Dy2Al0.42Fe4.58O12 interface. The results show that the transverse beam shifts related to the PSHE can be reversed by applying a small order of magnitude charge current (∼108 A·m−2) to the Pt layer in opposite directions, which predicts low dissipation in our proposed heterostructure. In addition, by applying an in-plane magnetic field, the saturation beam shifts can be increased, which can significantly enhance the switching ratio.

Vibration Characteristics of a Tubular Turbine Prototype at Different Heads with Considering Free Surface and Water Gravity

Tubular turbines are widely used in low water head and tidal power development due to their straight flow path, simple structure, and wide efficient area. However, the severe vibration during actual operation greatly affects the safe operation of the tubular turbine. This study performs a numerical calculation of the tubular turbine, which meets the actual machine conditions considering the free surface and water gravity; compares and analyzes the flow characteristics and pressure fluctuation spectrum characteristics in the tubular turbine under different water heads; and verifies the comparison with the actual machine test results to explore the vibration characteristics and vibration mechanism of the tubular turbine. Research results show that a large pressure difference is observed between the top and bottom of the runner chamber, and the runner needs to experience large periodic pressure fluctuations during rotation due to the combined effect of hydrostatic pressure and hydrodynamic pressure. Under different water heads, obvious flow turbulence and high turbulent kinetic energy areas are observed in the runner and draft tube due to the influence of the shape of the blade wake vortex. The vibration in the tubular turbine is mainly concentrated in the runner and draft tube and influenced by the water gravity and the runner structure of the transverse cantilever beam. The amplitude of pressure fluctuation is the largest when the frequency inside the runner is the blade passing frequency at each water head, so the maximum vibration position is located at the runner. The research results serve as a guide for the design and operation of the horizontal tubular turbine.

CFD Analysis and Wind Tunnel Experiment for Ventilation Ducts with Structural Elements Inside

Ventilation ducts with a high cross-sectional area are frequently built as structural ducts that include inside transversal structural beams. In this way, the cross-sectional area requested is respected, but the transverse structural elements will have a big impact on the airflow, with eventually additional noise and vibration and a high amount of energy wasted across the beams. From this perspective, the aim of this study is to evaluate the impact of the transversal beams inside the ventilation ducts, to analyze different alternatives for airflow improvement using computational fluid dynamics (CFD) simulation, and to check the simulation results in the wind tunnel with an experimental model. The results of the experimental measurements have highlighted the high-pressure drop and, consequently, the high energy wasted across the transversal structural beams. It was found that the airflow downstream of the beam is changing the flow direction, and high turbulences and vortices are initiated in the shadow of the beam. According to the CFD analysis, the ventilation system can be improved by adding airflow deflectors in the beam area. In this way, the high turbulences are reduced, the vortices and backflow are canceled, and the pressure losses across the beam area of the ventilation duct are reduced by up to 90% compared with the beam without a deflector. Therefore, the energy wasted in the beam area can be reduced by up to 90%.

Nonlinear cooling of an annular beam distribution

In recent years, intense efforts have been devoted to studying how nonlinear effects can be used to shape the transverse beam distribution by means of an adiabatic crossing of nonlinear resonances. By this approach, it is possible to split the beams in the transverse plane, so that the initial single-Gaussian beam is divided into several distinct distributions. This is at the heart of the multiturn extraction process that is successfully in operation at the CERN Proton Synchrotron. Nonlinear effects can also be used to cool a beam by acting on its transverse beam distribution. In this paper, we present and discuss the special case of a beam with an annular distribution, showing how its emittance can be effectively reduced by means of properly devised manipulations based on nonlinear effects.

COMPOSITE BRIDGES WITH CRACKED CONCRETE DECK SPANNING BETWEEN TRANSVERSE BEAMS UNDER FATIGUE SHEAR LOADING

AbstractFor concrete deck of large steel‐concrete composite road bridges cracking occurs due to tension because of negative bending moments at the support area, at the same time traffic load with high wheel loads passes the deck spanning between transverse beams. They induce cyclic shear loading in the cracked concrete deck. In composite bridges the application of prefabricated concrete elements has led to economical designs with a benefit in construction time. In this case, the prefabricated concrete elements are supported by the transverse beams when the on‐site concrete is poured. For this construction, the concrete is subjected to tension forces resulting from the global load‐carrying effect, which needs to be superimposed with local effects as wheel loads acting as shear fatigue loading. In this paper, the fatigue strength of cracked concrete deck under tension and shear fatigue loading is discussed.

Assessing the impact of eccentricity, slabs, and transverse beams on the behavior of reinforced concrete beam-column joints

In this study, a cyclic lateral load experiment was performed to assess the behavior of reinforced concrete (RC) beam-column joints with non-seismic detailing. For the experiment, eight full-scale joint specimens were prepared; the experimental variables were eccentricity, presence of slabs, and number of transverse beams. Most experimental objects showed joint shear failure after beam yielding, and their eccentricity reduced the joint shear strength. Although the joints had non-seismic details, the presence of the slabs and increased number of transverse beams strengthened the confinement within the joints, thereby enhancing the joint shear strength. The joint shear strength that was calculated based on the equation suggested in ASCE 41-17 showed a substantial discrepancy from the actual measurement, primarily because the calculation neglected the impact of the slabs and number of transverse beams. Therefore, to improve the performance prediction, an actual three-dimensional shape of the joints must be considered. Additionally, based on further research outcomes, more factors that affect joint behavior must be considered in future relevant standards.

Normalization of proton-radiographic images of objects with quasi-uniform areal density

A technique of calculating the beam transmission through static objects with a quasi-uniform areal density using a single proton-radiographic image was developed under the condition of a gaussian-like transverse beam profile. The calculated transmission images are intended for the density reconstruction of the objects under study. A proton-radiographic investigation of static targets was carried out at the experimental facility with special magnetic optics PUMA at proton energy of 800 MeV and particle intensity 1010 per image. It has been shown that the use of the technique allows restoring the transmission of an object under study with an average relative error of about 1-1.2%.

Preparation of different carbon stripper foils and application in beam diagnostics

The production of carbon stripper foils that are mounted at different locations of the heavy-ion accelerator is an important task of the target laboratory, and the process for the preparation of carbon foils is constantly improved. Recently, we tested additional heat treatment of the carbon stripping foils following our standard procedure to reduce stress in the foils, since the performance and the durability of these stripping foils is a crucial factor for effective operation. We investigated the properties of foils produced some time ago and of foils freshly produced with the standard procedure, and foils treated thermally after the standard procedure. For the beam diagnostic department at GSI radiation resistant target materials for transverse ion beam profile measurement is an ongoing research topic. In that framework, the feasibility of Optical Transition Radiation (OTR) generation due to ion beam interaction with metal target for beam profile determination has been investigated. Here, carbon stripper foils are applied to enhance the OTR signal. The differently prepared foils were applied in many different experiments of the beam diagnostic department. We describe the performance of the foils during irradiation and compare the features of foils before and after irradiation.

Status of the development of the electron lens for space charge compensation at GSI

At GSI a prototype electron lens for space charge (SC) compensation is currently being designed and main components as the RF-modulated electron gun are already under commissioning. The goal of this project is the (partial) compensation of SC forces within the ion beam by an overlapping electron beam. This may help to increase the intensity of primary beams, especially in the FAIR facility and potentially all large synchrotrons operated at the SC limit. For an effective SC compensation, the generated electron beam needs to follow the transverse and longitudinal beam profile of the ion bunch structure. The requirements are maximum currents of 10 A and grid modulation to cover a broad frequency range from 400 kHz to 1 MHz. The RF-modulated electron gun was designed and manufactured in the scope of the ARIES collaboration and is currently being tested at the E-Lens Lab of Goethe-University Frankfurt. A dedicated test bench was built for commissioning of the major e-lens components and diagnostics. In this contribution the overall set-up will be presented putting special emphasis on the beam dynamics and collector design as well as simulation results of the electron gun.

Construction and tests of phosphor view screen station for monitoring transverse profile of electron beam at PCELL

Development of an accelerator-based light source for generating coherent terahertz (THz) and mid-infrared (MIR) free-electron laser (FEL) is ongoing at the PBP-CMU Electron Linac Laboratory (PCELL). For producing high quality radiation, suitable electron beam property is necessary. In particle accelerator technology, transverse beam distribution and profile can be measured by using several techniques. The beam monitoring using view screen station is one of popular and effective methods. At PCELL, we use stations consisting of phosphor screen equipped with CCD camera to monitor, measure and record the beam image along the accelerator system and beamlines. The phosphor screen was chosen due to its high spatial resolution. The phosphor film is uniformly coated on a thin aluminium plate. Its green emission when electrons hitting the screen is matched well with the respond of the CCD camera. The screen can be moved in and out from the vacuum chamber using the air pressurized linear actuator. This paper presents about design, construction and tests of the screen stations at PCELL. The resolution of measurements for beam transverse profile and emittance is also be discussed.

A carbon minibeam irradiation facility concept

In minibeam therapy, the sparing of deep-seated normal tissue is limited by transverse beam spread caused by small-angle scattering. Contrary to proton minibeams, helium or carbon minibeams experience less deflection, which potentially reduces side effects. To verify this potential, an irradiation facility for preclinical and clinical studies is needed. This manuscript presents a concept for a carbon minibeam irradiation facility based on a LINAC design for conventional carbon therapy. A quadrupole triplet focuses the LINAC beam to submillimeter minibeams. A scanning and a dosimetry unit are provided to move the minibeam over the target and monitor the applied dose. The beamline was optimized by TRAVEL simulations. The interaction between beam and these components and the resulting beam parameters at the focal plane is evaluated by TOPAS simulations. A transverse beamwidth of < 100 μm (sigma) and a peak-to-valley (energy) dose ratio of > 1000 results for carbon energies of 100 MeV/u and 430 MeV/u (∼ 3 cm and 30 cm range in water) whereby the average beam current is ∼ 30 nA. Therefore, the presented irradiation facility exceeds the requirements for hadron minibeam therapy.

The resistive wall impedance and the effects of the non-evaporable getter thickness in an ultra-low emittance ring

In modern particle accelerators with ultra-low emittance, the vacuum chambers are designed based on Non-Evaporable Getter (NEG)-coated vacuum chambers. The thickness of the NEG coating plays a critical role in the dynamic beam effects. So, in this paper, the longitudinal and transverse impedance of a copper chamber coated with a NEG are investigated, and the effects of the NEG thickness over a wide range of frequencies have been studied. A good selection of NEG layer thickness could minimize the coating effects on the longitudinal and transverse beam impedance. The numerical results in this work show that the beam dynamic effects could be minimal with selecting a NEG coating thickness of about 1 μm.

Surrogate-based Bayesian inference of transverse beam distribution for non-stationary accelerator systems

Constraints on the beam diagnostics available in real-time and time-varying beam source conditions make it difficult to provide users with high-quality beams for long periods without interrupting experiments. Although surrogate model-based inference is useful for inferring the unmeasurable, the system states can be incorrectly inferred due to manufacturing errors and neglected higher-order effects when creating the surrogate model. In this paper, we propose to adaptively assimilate the surrogate model for reconstructing the transverse beam distribution with uncertainty and underspecification using a sequential Monte Carlo from the measurements of quadrant beam loss monitors. The proposed method enables sample-efficient and training-free inference and control of the time-varying transverse beam distribution.

Modeling and mitigation of long-range wakefields for advanced linear colliders

The luminosity requirements of TeV-class linear colliders demand use of intense charged beams at high repetition rates. Such features imply multi-bunch operation with long current trains accelerated over the km length scale. Consequently, particle beams are exposed to the mutual parasitic interaction due to the long-range wakefields excited by the leading bunches in the accelerating structures. Such perturbations to the motion induce transverse oscillations of the bunches, potentially leading to instabilities such as transverse beam break-up. Here we present a dedicated tracking code that studies the effects of long-range transverse wakefield interaction among different bunches in linear accelerators. Being described by means of an efficient matrix formalism, such effects can be included while preserving short computational times. As a reference case, we use our code to investigate the performance of a state-of-the-art linear collider currently under design and, in addition, we discuss possible mitigation techniques based on frequency detuning and damping.

Порівняльний аналіз несучої здатності дослідних пошкоджених залізобетонних елементів, підсилених металевими обоймами

The paper presents research results and a comparative analysis of the load-bearing deformability and crack resistance of basalt concrete beams brought to the limit state (ULS) in previous tests. The beams were reinforced with prestressed metal clips under high-level static and low-cycle alternating loads. The work performed comparative calculations of reinforced building structures using proprietary methods and existing regulatory methods. A comparison of the experimental and calculated values of the bearing capacity of damaged experimental beam samples showed their unsatisfactory convergence because the well-known regulatory and proprietary methods provide for the calculation of the bearing capacity of damaged reinforced concrete structures along a dangerous inclined crack under the predominant action of transverse force, i.e. the top of a dangerous inclined crack and clamps and vertical elements of external reinforcement. However, experimental and theoretical studies have shown that the destruction of prototype beams with large and medium shear spans under a variable low-cycle load occurs along dangerous inclined through cracks, from the overwhelming action of bending moments, in the longitudinal reinforcement elements of the frame, in the longitudinal tensile reinforcement, as well as transverse beam beams and yield stress cages. That is, the real physical picture of the operation of the system “damaged reinforced concrete beam – prestressed metal reinforcement cage” under alternating transverse load at high levels differs significantly from the physical model of previously existing regulatory and proprietary methods. All existing regulatory and proprietary methods provide for the calculation of the bearing capacity of damaged reinforced concrete structures along a dangerous inclined crack under the predominant action of transverse force, that is, the components of the bearing capacity of inclined sections on concrete above the top of a dangerous inclined crack and clamps and external elements are taken into account. Experimental and theoretical studies have shown that the destruction of prototype beams with large and medium shear spans, under alternating low-cycle loads, occurs along dangerous inclined through cracks from the overwhelming action of bending moments in the longitudinal tensile reinforcement, as well as in the transverse rods of the beam and the cage yield strength.

Effect of the composition of multicomponent powders on the mechanical and tribotechnical properties of coatings obtained by laser additive technologies

The paper presents the results of metallographic studies and tribotechnical tests of samples of medium-carbon steel 34KhNi3MoA and coatings obtained by laser surfacing of a powder multicomponent charge based on iron and cobalt in a ratio of 3:1 with additives of nano particles of tantalum carbide. The samples were processed with a circular defocused beam and with transverse beam oscillations normal to the scanning speed. Comparative tests for friction and wear were carried out in a pair with a hardened 40Kh steel counterplate. The load and sliding speed during the tests varied discretely. Turbine oil TP 22C was used as a lubricant. It is shown that the introduction of additives of nano-tantalum carbide into the charge reduces friction losses, increases the wear resistance of coatings compared to the charge without carbides and the base material. The wear resistance of coatings with an increase in the amount of the hardening phase increases compared to the original steel. It has been established that the technology of laser surfacing with multicomponent coatings with nano particles of tantalum carbide can be used to restore worn surfaces of shaft necks, turbine blades, thrust discs, shut-off valves and other parts operating at high temperatures and in corrosive environments.

Spectral distribution and flux of [formula omitted]-ray beams produced through Compton scattering of unsynchronized laser and electron beams

Intense, quasi-monochromatic, polarized γ-ray beams with high and tunable energy produced by Compton scattering of laser photons against relativistic electrons are used for fundamental studies and applications. Following a series of photoneutron cross section measurements in the Giant Dipole Resonance (GDR) energy region performed at the NewSUBARU synchrotron radiation facility, we have developed the eliLaBr Monte Carlo simulation code for characterization of the scattered γ-ray photon beams. The code is implemented using Geant4 and is available on the GitHub repository (https://github.com/dan-mihai-filipescu/eliLaBr). Here we report the validation of the eliLaBr code on NewSUBARU LCS γ-ray beam flux and spectral distribution data and two applications performed with it for asymmetric transverse emittance profiles electron beams, characteristic for synchrotrons.The first application is based on a systematic investigation of transverse collimator offsets relative to the laser and electron beam axis. We show that the maximum energy of the LCS γ-ray beam is altered by vertical collimator offsets, where the edge shifts towards lower energies with the increase in the offset.Secondly, using the eliLaBr code, we investigate the effect of the laser polarization plane orientation on the properties of the LCS γ-ray beams produced with asymmetric emittance electron beams. We show that:1. The use of vertically polarized lasers contributes to the preservation of the LCS γ-ray beam maximum energy edge by increasing the precision in the vertical collimator alignment.2. Under identical conditions for the electron and laser beams phase-space distributions, the energy spectrum of the scattered LCS γ-ray beam changes with the laser beam polarization plane orientation. More precisely, the use of vertically polarized laser beams slightly deteriorates the LCS γ-ray beam energy resolution.