Transport Properties Of Membranes Research Articles

Estimation of mixed-gas selectivity of membranes using the linear friction-based model

The development of analytical models for predicting the transport properties of membranes in the separation of multicomponent mixtures is highly relevant because (1) measurements of permeability and sorption of gas mixtures in membrane materials are laborious and time-consuming, and (2) estimation of transport properties based on pure gas measurements is desirable, however, rather unreliable and can lead to serious errors. In this paper, within the framework of the well-known frictional-coefficient formalism, we present nonlinear equations for the fluxes of gas mixture components through the membrane, which take into account the diffusional coupling of the fluxes compared to independent gas transport. As a result, an analytical equation for the mixed-gas selectivity was obtained. This equation has an implicit form, which is not quite convenient for practical application, since it has to be solved numerically. A simple explicit expression for mixed gas selectivity was derived using the so-called linear transport model, which is a linearized version of the original nonlinear flux equations. It is important to emphasize that a comparison of the linear model with the formally more rigorous nonlinear model showed only minor quantitative differences. The input parameters for the model are the single gas transport parameters. Testing the linear model using experimental data for the separation of hydrocarbons (n-butane/methane, n-butane/i-butane, propylene/propane) revealed an acceptable fit. A comparison of the model with recent experimental data on the separation of CO2-containing mixtures using microporous polymers is also presented. It is found that the calculated CO2/N2 mixed gas selectivity is in good agreement with the experimental data, while only a semi-quantitative agreement is observed for the CO2/CH4 separation. Besides, it is shown that the model developed for binary gas separation can be extended to ternary gas mixtures.

Removal of Methylene Blue Dye from Aqueous Solutions Using Polymer Inclusion Membrane Containing Calix[4]pyrrole.

The effective purification of aqueous solutions of methylene blue dye was tested using polymer inclusion membranes (PIMs) that contained cellulose triacetate (CTA) as a polymer base, o-nitrophenyl octyl ether (o-NPOE) as a plasticizer, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) as a carrier. Scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy were used to define the microstructure and surface of PIMs. Experimental results showed that, with an increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation showed that the flux increased with the rise in the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane's transport properties. The optimal composition of the membrane in percent by weight for KP was 74% plasticizer; 18% support, and 8% carrier. The maximum MB removal (93.10%) was achieved at 0.10 M HCl solution as the receiving phase. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Sulfonated poly(ether ether ketone)-Protic ionic Liquid-Based anhydrous Proton-Conducting composite polymer electrolyte membranes for High-Temperature fuel cell applications

A high-temperature polymer electrolyte membrane fuel cell (PEMFC) has enormous potential to produce clean energy with minimal environmental pollution along with high energy density and conversion efficiency. In the present work, anhydrous proton-conducting polymer electrolyte membranes for prospective high-temperature fuel cell application were successfully prepared using different protic ionic liquids (PILs) and sulfonated poly(ether ether ketone) (SPEEK). The protic ionic liquids (PILs), 2-hydroxyethylammonium formate, diethylmethyl ammonium triflate, 1-ethylimidazolium bis(trifluoromethylsulfonyl)imide, 1,2-dimethyl imidazolium bis(trifluoro methylsulfonyl)imide, and diethylmethylammonium methanesulfonate were selected based on their favorable physicochemical properties. The effect of the incorporation of the PIL on the structural, thermal, and electrical transport properties of the composite SPEEK polymer electrolyte membranes was studied. The prepared polymer electrolyte membranes (PEMs) were characterized using Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffractometry (XRD), and electrochemical impedance spectroscopy (EIS) techniques. FTIR results indicated an interaction between the PIL and the SPEEK, which resulted in homogeneous and flexible membranes. The DSC results confirmed good miscibility and elucidated plasticizing effect of the incorporated PIL on the SPEEK polymer matrix. All the PEMs showed good thermal stability and high-temperature anhydrous proton conductivity, achieving best proton conductivity, ≈8 × 10–3 S cm−1 at 120 °C and low activation energy ≈0.26 eV, making it suitable for prospective high-temperature PEMFC applications.

Transport properties of ethylene glycol functionalized membranes exposed to nonaqueous electrolytes

Non-aqueous redox flow batteries (RFBs) are a promising technology to meet growing demand for grid-scale energy storage. Membrane separators, designed specifically for use with organic solvents, are necessary to advance non-aqueous RFBs. Herein, we report the development of a series of poly(phenylene oxide) (PPO) membranes functionalized with poly(ethylene glycol) (PEG) side chains to investigate the influence of PEG side chain length and degree of PEGylation on membrane transport properties. Increasing the degree of PEGylation generally led to increases in electrolyte uptake, hydroxy TEMPO permeability, and ionic conductivity likely caused by an increase in overall PEG content, as opposed to specific interactions caused by changing the degree of PEGylation. For membranes with similar PEG content, increasing the length of the PEG side chain resulted in decreases in electrolyte uptake, permeability, and conductivity possibly due to differences in the solvation behavior of the PEG chains with different lengths.

Permeance of Condensable Gases in Rubbery Polymer Membranes at High Pressure.

The gas transport properties of thin film composite membranes (TFCMs) with selective layers of PolyActive™, polydimethylsiloxane (PDMS), and polyoctylmethylsiloxane (POMS) were investigated over a range of temperatures (10-34 °C; temperature increments of 2 °C) and pressures (1-65 bar abs; 38 pressure increments). The variation in the feed pressure of condensable gases CO2 and C2H6 enabled the observation of peaks of permeance in dependence on the feed pressure and temperature. For PDMS and POMS, the permeance peak was reproduced at the same feed gas activity as when the feed temperature was changed. PolyActive™ TFCM showed a more complex behaviour, most probably due to a higher CO2 affinity towards the poly(ethylene glycol) domains of this block copolymer. A significant decrease in the permeate temperature associated with the Joule-Thomson effect was observed for all TFCMs. The stepwise permeance drop was observed at a feed gas activity of p/po ≥ 1, clearly indicating that a penetrant transfer through the selective layer occurs only according to the conditions on the feed side of the membrane. The permeate side gas temperature has no influence on the state of the selective layer or penetrant diffusing through it. The most likely cause of the observed TFCM behaviour is capillary condensation of the penetrant in the swollen selective layer material, which can be provoked by the clustering of penetrant molecules.

Single and mixed gas permeability studies on mixed matrix membranes composed of MIL-101(Cr) or MIL-177(Ti) and highly permeable polymers of intrinsic microporosity

The gas transport properties of mixed matrix membranes (MMMs), prepared by dispersing nanoparticles of MOFs MIL-101(Cr) or MIL-177(Ti) into highly permeable Polymers of Intrinsic Microporosity PIM-EA-TB or PIM-TMN-Trip, were investigated. The homogeneity of the dispersion was confirmed by means of Scanning Electron Microscopy (SEM) and Energy-dispersive X-ray (EDX) mapping analysis. Single gas time-lag measurements provided the permeability and ideal selectivity of different gas pairs, both after treatment of the MMMs with methanol and after natural aging over an extended period (up to 2000 days). This data demonstrated that the gas size-sieving pores of MIL-101(Cr) and MIL-177(Ti) and their good dispersion into the PIM matrix results in MMMs with enhanced gas separation performance, as compared to films composed solely of the polymer. The comparison of actual permeability with the Maxwell model for PIM-EA-TB with both MOFs confirmed the good dispersion and the absence of anomalies, whereas the inconsistency of permeability with prediction data for PIM-TMN-Trip suggests that the MOFs improved the polymer properties, stiffening or occupying the polymer free volume. In particular, the incorporation of MIL-101(Cr) into PIM-EA-TB significantly enhances the H2 permeability from ∼6000 to 13,000 Barrer, with a concurrent increase of the H2/N2 selectivity from 14 to 21. MIL-177(Ti) also enhances the H2/N2 selectivity to 20 due to a slight reduction of the N2 permeability. The addition of MIL-101(Cr) and MIL-177(Ti) into the ultra-permeable PIM-TMN-Trip showed more modest increases in H2 permeability and H2/N2 selectivity from 4.6 to ∼ 10. Hence the data for some of the MMMs surpass the 2008, and even approach the 2015/2019 Robeson’s upper bounds, particularly for gas pairs including H2.

Inverse pH Gradient-Assay for Facile Characterization of Proton-Antiporters in Xenopus Oocytes.

Xenopus oocytes represent one of the most versatile model systems for characterizing the properties of membrane transporters. However, for studying proton-coupled antiporters, the use of Xenopus oocytes has so far been limited to so-called injection-based transport assays. In such assays, where the compound is injected directly into the oocytes' cytosol and transport is detected by monitoring substrate efflux, poor control over internal diffusion and concentration are incompatible with mechanistic characterizations. In this study, we present an inverse pH-gradient transport assay. Herein, an outward-facing proton gradient enables the characterization of proton antiporters via facile import-based transport assays. We describe two approaches for establishing sustained outward-facing proton gradients across the oocyte membrane, namely by applying alkaline external conditions or through surprisingly stable carbonyl cyanide m-chlorophenyl-hydrazone (CCCP)-mediated acidification of the cytosol. Previously, genetic evidence has shown that DTX18 from Arabidopsis thaliana is essential for the deposition of the hydroxycinnamic acid amide p-coumaroylagmatine (coumaroylagmatine) defence compound on the leaf surface. However, direct evidence for its ability to transport coumarol-agmatine has not been provided. Here, using Xenopus oocytes as expression hosts, we demonstrate DTX18's ability to transport coumaroyl-agmatine via both injection-based and inverse pH-gradient transport assays. Notably, by showing that DTX18 is capable of accumulating its substrate against its concentration gradient, we showcase the compatibility of the latter with mechanistic investigations.

Copolyimide molecular brushes with poly(methacrylic acid) side chains as additive to polyphthalamide membrane: Organization, physical, and transport properties

AbstractMacromolecules of complex architecture find application as modifiers of commercial polymeric membrane materials. In this work, copolyimide molecular brushes (coPI) composed of polyimide backbone and poly(methacrylic acid) side chains were used to modify poly(m‐phenylene iso‐phthalamide) (PPA). Structure, physical, mechanical, and transport properties of dense nonporous PPA/coPI membranes containing up to 10 wt% coPI were studied. The effect of included coPI on the membrane structure was estimated using atomic force microscopy and mechanical tests. The coPI modifier contributes to the additional formation of free volume elements evenly distributed throughout the membrane. Transport properties of PPA/coPI membranes were investigated via sorption tests and pervaporation separation of methanol (MeOH) and methyl tert‐butyl ether (MTBE) mixtures. The inclusion of coPI modifier in the PPA membrane leads to an increase in the total flux of the membrane. The highest separation factor was found for the PPA/coPI membrane containing 10 wt% coPI; transport properties of the best membrane were compared with the literature data on separation of the azeotropic MeOH–MTBE mixture.

A Comprehensive Study on the Effect of Plasticizers on the Characteristics of Polymer Inclusion Membranes (PIMs): Exploring Butyl Stearate as a Promising Alternative.

This study investigated the influence of various plasticizers commonly used in the manufacture of polymer inclusion membranes (PIMs), such as 2-nitrophenyl octyl ether (NPOE), phthalates, adipates, and sebacates on the mechanical, thermal, and transport properties of membranes. Additionally, butyl stearate (BTS), chosen for its non-toxic nature compared to phthalates and its cost-effectiveness relative to adipates and sebacates, was evaluated as a plasticizer in PIMs for the first time. All plasticizers were incorporated in PIMs made of either cellulose triacetate (CTA) or poly(vinyl chloride) (PVC) as the base polymers and the task-specific ionic liquid trioctylmethylammonium thiosalicylate (TOMATS) as the carrier. The plasticizers were found to significantly affect the characteristics of membrane hydrophilicity, mechanical flexibility, and thermal stability. Transport experiments using Hg(II) as a model target ion revealed that, for CTA-based PIMs, the plasticizer did not significantly affect transport efficiency. However, for PVC-based PIMs, BTS exhibited better efficiency when compared to NPOE. These findings highlight the potential of BTS as an attractive alternative to currently used plasticizers in PVC-based PIM formulations.

Mechanism of Ionomer Film Formation via Solution Drying.

Film formation via the drying of ionomer solutions is a crucial process that has a strong influence on the morphology and transport properties of polymer electrolyte membranes and thin films. However, the microscopic mechanism of this process remains unclear. Here, we elucidate this mechanism using a coarse-grained model based on all-atom molecular dynamics that accurately reproduces small-angle X-ray scattering spectra. In dilute ionomer solutions, ionomers form rod-like bundles with diameters of 1.5-2 nm. As the water solvent evaporates, these bundles gradually aggregate and connect to each other, while maintaining their diameter. Finally, the remaining water forms nanosized clusters surrounded by the surfaces of the bundles with hydrophilic sulfonate groups.

Cucurbit[6]uril builds a water channel for improving the water/salt selectivity of polybenzimidazole

Polybenzimidazole (PBI) has garnered significant interest in desalination due to its exceptional chemical stability and mechanical strength, but suffers from poor water permeability. In this work, different contents of hydroxylated Cucurbit [6]uril (CB [6] were added to PBI to build a “water transport channel”. The effects of CB [6] addition on the chemical structure and surface morphology were analyzed by FTIR, SEM, and Zeta potential, respectively. Based on the solution-diffusion model, the effect of CB [6] on the water/salt transport properties of PBI membranes was thoroughly investigated. The results show that appropriate CB [6] doping can enhance water sorption of PBI through the special “outer hydrophilic and inner hydrophobic cavity” structure, and boost water diffusion with the channeling effect of the hydrophobic CB [6] cavity. While the complexation between the carbonyl group in CB [6] and Na+ ions slightly increased salt sorption, the specific cavity structure of CB [6] can significantly decrease salt diffusion by blocking salt ions and increasing transport path tortuosity. The cavity effect of CB [6] was further confirmed by hybridizing CB [6] with biphenylsulfonyl-substituted PBI when the cavity can be occupied. Therefore, the introduction of CB [6] improves the water/salt diffusion selectivity and then the permeability selectivity of PBI. Notably, the PBI@CB [6] membrane with a 0.25 wt% CB [6] loading exhibited a 40-fold increase in water permeability coefficient compared to pure PBI, while experiencing only a slight decrease in salt permeability coefficient, water/salt selectivity almost exceeding the empirical upper bound line of polymers. This work provides a theoretical foundation for the development of high-performance desalination membranes based on macrocyclic molecules such as CB [6].

Structural Characterization and Physicochemical Properties of Functionally Porous Proton-Exchange Membrane Based on PVDF-SPA Graft Copolymers.

Fluorinated proton-exchange membranes (PEMs) based on graft copolymers of dehydrofluorinated polyvinylidene fluoride (D-PVDF), 3-sulfopropyl acrylate (SPA), and 1H, 1H, 2H-perfluoro-1-hexene (PFH) were prepared via free radical copolymerization and characterized for fuel cell application. The membrane morphology and physical properties were studied via small-(SAXS) and wide-angle X-ray scattering (WAXS), SEM, and DSC. It was found that the crystallinity degree is 17% for PEM-RCF (co-polymer with SPA) and 16% for PEM-RCF-2 (copolymer with SPA and PFH). The designed membranes possess crystallite grains of 5-6 nm in diameter. SEM images reveal a structure with open pores on the surface of diameters from 20 to 140 nm. Their transport and electrochemical characterization shows that the lowest membrane area resistance (0.9 Ωcm2) is comparable to perfluorosulfonic acid PEMs (such as Nafion®) and polyvinylidene fluoride (PVDF) based CJMC cation-exchange membranes (ChemJoy Polymer Materials, China). Key transport and physicochemical properties of new and commercial membranes were compared. The PEM-RCF permeability to NaCl diffusion is rather high, which is due to a relatively low concentration of fixed sulfonate groups. Voltammetry confers that the electrochemical behavior of new PEM correlates to that of commercial cation-exchange membranes, while the ionic conductivity reveals an impact of the extended pores, as in track-etched membranes.

Structure and transport properties of self-assembled nanofiltration membranes based on sustainably derived materials

The development of functional polymers using sustainable resources is an increasingly important pursuit. Unsaturated fatty acids represent a potentially interesting class of renewable materials for this purpose. Their unsaturated carbon bonds permit crosslinking to form solid polymers. Additionally, their carboxylic acid functional groups provide for the display of specific surface chemistry within the resulting polymers, and also enable chemical derivatization. Here, we explore the fabrication of nanometer-scale size-selective membranes using conjugated linoleic acid derived monomers. Potassium salt conjugated linoleic acid surfactants (KCLA) self-assembled to form hexagonally packed cylinders (HI) in an aqueous medium containing glycerol. This structure provides a highly ordered medium with aqueous-continuous channels for nanofiltration. The HI mesophase was crosslinked with the addition of bifunctional comonomers and the ordered structure was retained with good fidelity in the resulting thin polymer films (< 400 nm thick). These film function effectively as nanofiltration membranes, with a size cut-off of approximately 1.2 nm for charged solutes, while maintaining a high permeance of ∼ 9 LMH/bar. This performance is on par with several commercial nanofiltration membranes and these materials are therefore of potential interest for advancing sustainability concerns in practical nanofiltration applications.

Composite membranes based on ether oxygen-rich polyimide with superior CO2/N2 separation properties prepared by interfacial polymerization

Ether oxygen-rich polymeric membranes emerge as promising membranes in CO2 separation due to the high affinity between CO2 molecules and ethylene oxide segments. However, there is a massive challenge in developing asymmetric membranes with high CO2 permeation performance and CO2/light gas separation performance. This work revealed composite membranes with ether oxygen-rich polyimide separation layers were developed by interfacial polymerization between 1,2,4,5-benzenetetracarbonyl tetrachloride and commercial diamines named o,o'-bis(2-aminopropyl) polypropylene glycol-block-polyethylene glycol-block-polypropylene glycol followed by thermal imidization. The influences of the polymerization time and monomer concentrations on the gas transport and separation properties of the composite membranes were studied based on single-gas permeation. The optimum membrane possessed a superior high ideal CO2/N2 separation factor of 429 accompanied with a moderate permeance of 150 GPU for CO2 at 25oC and 0.2 MPa. The performance stability was studied by operating the membrane at various pressures and temperatures. The result showed the composite membrane possessed excellent plasticization resistivity at high pressures. The separation property of composite membranes for CO2/N2 binary mixture was also evaluated. The influences of the operation parameters, including stage-cut and pressure ratio on the product purity and recovery were investigated. The results showed great practical application potential in efficient separation of flue gas.

Membrane transport of polyfunctional alkyl (N-alkyl-N,N-dioctylammoniomethyl)phosphonates

The membrane transport properties of phosphorylated betaines in relation to mono- and polyfunctional carboxylic acids were studied. The structure of transferred H-complexes was discussed; using IR spectroscopy, the main coordination centers of carriers were revealed. Using the method of quantum chemical calculations, the relationship between the amount of substrate flux, their lipophilicity and the structure of the resulting H-complexes was shown.

Solid electrolytes based on cellulose nanocrystals with protic ionic liquid for next-generation fuel cells

AbstractThe search for solid electrolytes which have good proton conductivity in anhydrous conditions, thermal and mechanical stability, and are at the same time environmentally friendly and easy to manufacture is a big challenge which we have undertaken. This work presents new solid electrolytes based on cellulose nanocrystals with protic ionic liquid 1-methylimidazolium bis(trifluoromethylsulfonyl) imide (PIL) which have been obtained and whose thermal and conductivity properties and nanoscale organization has been determined. Two membranes were synthesized which differ as to the amount of absorbed PIL. They show excellent thermal stability up to 200 °C. The maximum value of ionic conductivity is about 10−2 S/m at 200 °C in anhydrous conditions and falls in the range of 10−3–10−2 S/m for temperatures from 150 to 200 °C. The correlation between the transport properties of membranes and their nanostructure has been probed by solid-state nuclear magnetic resonance spectroscopy. The thermal and conductivity properties of the new materials can compete with currently available membranes. Further work on a composite with a similar chemical composition should lead to obtaining a membrane capable of operating in next-generation fuel cells (T &gt; 120 °C).

Development of a Pharmacokinetic Model That Accounts for the Plasma Concentrations of Conjugated and Unconjugated Bilirubin Observed in a Variety of Disease States.

For a large variety of liver pathologies, the plasma unconjugated (UB) and conjugated (CB) bilirubin concentrations appear to be coupled. For example, in alcoholic cirrhosis, UB and CB are roughly the same over a large range of total bilirubin, requiring an initial massive increase (about 40-fold) in plasma CB to reach the level of UB and then similar increases in UB and CB as the disease progresses. This coupling has been either unrecognized or ignored and this paper is the first attempt to try to explain it quantitatively in terms of known hepatic cell metabolic and membrane transport properties. A simplified pharmacokinetic model is developed and applied to a variety of hyperbilirubinemic pathologies. A central feature of the model is based on the recent observation that double knockout of the rat OATP1A and OATP1B hepatic transporters produces a roughly 400-fold increase in plasma CB, indicating that there is a normal rapid recycling of CB from the cell to the plasma with reuptake via OATP. We use the experimental rat Km of OATP CB transport to show that OATP uptake becomes saturated at relatively low plasma CB concentrations, decreasing uptake, and producing massive (up to 1000-fold) increases in CB in some pathologies. It is assumed that UB and CB are competing for the OATP transporter, producing the increased plasma UB that is observed in "pure" CB pathologies. The model accurately describes the clinically observed UB and CB for pure UB (Gilbert's, hemolytic anemia) and CB (Dubin-Johnson, Rotor syndrome, biliary atresia) pathologies as well as in cirrhosis. This model is a preliminary, first attempt to quantitatively describe UB and CB pharmacokinetics. It is hoped that it will stimulate more detailed measurements and analysis.

Effect of Boiling Pretreatment on Physicochemical and Transport Properties of Perfluorosulfonic Acid Membrane

Effect of Boiling Pretreatment on Physicochemical and Transport Properties of Perfluorosulfonic Acid Membrane

Water vapor sorption and transport in carbon molecular sieve membranes

Carbon Molecular Sieve (CMS) membranes have been extensively studied for gas separations. Many gas separation applications involve humidified streams, but reports on water vapor transport in CMS membranes are limited. In this study, water permeability, diffusivity, and solubility were determined as a function of water activity for CMS membranes. Water transport properties of membranes synthesized at different pyrolysis temperatures (550 °C and 800 °C) and with different polyimide precursors were examined. Water sorption followed Type V isotherms as previously observed for the adsorption of water in microporous carbons. Water permeability was much higher at all water activity values for CMS samples prepared at lower pyrolysis temperature. Water permeabilities as a function of water activity of the three different polyimides pyrolyzed at 800 °C were very similar. Water permeability of CMS membranes was high compared to many other polymeric materials, showing potential for dehydration applications. Finally, the steady-state water vapor diffusivity (Dss), estimated from steady state permeability and equilibrium sorption measurements, was compared to the experimental transient diffusivity (D), matching reasonably well.

Correlations between the dopant concentration and ion transport properties of plasticized NaCMC-Pectin polyblend electrolyte membranes for electrochemical device applications

This study explores the structural and electrical properties of sodium carboxymethyl cellulose (NaCMC)–pectin (PC)–glycerol–NH4Br electrolyte films and investigates their potential applications in proton batteries. Plasticized solid polymer electrolyte (SPEs) films were fabricated using the solution casting method. The interaction between the salt and polymer blends was verified using Fourier-transform infrared (FTIR) analysis. Incorporation of various salt concentrations (up to 25 wt%) was found to enhance the amorphous phase of the polymer blend, as evidenced by X-ray diffraction (XRD) results. Additionally, the decrease in the glass transition temperature, as confirmed by DSC analysis, indicates that the inclusion of both plasticizer and salt contributed to this effect. An electrolyte with 25% wt. of NH4Br has the highest room temperature conductivity of 4.68 ×10−4 S cm−1. This electrolyte was employed to fabricate the proton battery for energy storage application.