Transmission Electron Microscopy Investigations Research Articles

Hydrophobic polymer nano hybrid ternary composite electrode for nanomolar tracing of Cd2+ ions

AbstractIn the present study, we reported the successful synthesis of a ternary nano hybrid polymer composite system obtained by solution casting. Composing carbon nanotubes (CNTs) and molybdenum disulfide (MoS2) in ethylene vinyl acetate (EVA) derived ECM ternary electrode. It demonstrated an excellent electrochemical sensor performance and a more efficient supercapacitor. Chemical structure of hybrid electrode Fourier transform Infrared Spectroscopy (FTIR) illustrated the CS and CN stretching with MoS2 and CNT new bands (at 1368 and 1032 cm−1). FE‐SEM and Atomic force microscopy (AFM) 3D topographic image identified the decreased rough morphology of the hybrid electrode. Whereas contact angle measurements revealed the enhanced wettability of electrode system. Microporous nature of the hybrid electrode was observed through SEM investigation. Transmission electron microscopy (TEM) revealed the nano hybrid entity in a hybrid electrode system. XRD and TEM investigation confirmed semicrystalline phase of the hybrid electrode system due to the presence of MoS2. D band, G bands, E12g and A1g vibrational modes in Raman spectroscopy revealed the occupied hybrid filler CNTs and MoS2. An electroactive site for the Cd2+ ion sensor was confirmed by the ECM/PGE hybrid electrode. It comply the desirable sensor qualities, such as excellent selectivity, reproducibility and repeatability with a high accuracy and lower detection limit of 15 nM. Additionally, the ECM/PGE electrode demonstrated a capacitive nature with an aerial capacitance of 73 μF/cm2 at an applied current density of 3 μA/cm2. Furthermore, it exhibited a power density of 44 mW/cm2 and an energy density of 148 μWh/cm2 over a wide potential range of 1 V.

Ultrastructural and morphological studies on variables affecting Escherichia coli with selected commercial antibiotics

BackgroundMany studies reported the effects of antibiotic exposure on E. coli bacterial growth and cell modification. However, scarce descriptive information on ultrastructural effects upon exposure of commercial antibiotics. MethodsThis study described the morphological and ultrastructural alterations caused by selected antibiotics (amoxicillin-clavulanate, ceftriaxone, polymyxin B, colistin, gentamicin, and amikacin) that targeted cell wall, plasma membrane, and cytoplasmic density, and also proteins synthesis. We determined extracellular morphological changes of exposure through scanning electron microscopy (FESEM) and intracellular activities through transmission electron microscopy (TEM) investigation. ResultsFESEM and TEM micrograph of E. coli exposed with selected antibiotics shows ultrastructural changes in beta-lactam class (amoxicillin-clavulanate, ceftriaxone) elongated the cells as the cell wall was altered as it inhibits bacterial cell wall synthesis, polymyxin class (polymyxin B, colistin) had plasmid and curli-fimbriae as it breaking down the plasma/cytoplasmic membrane, and aminoglycoside class (gentamicin, and amikacin) reduced ribosome concentration as it inhibits bacterial protein synthesis by binding to 30 s ribosomes. ConclusionMorphological and ultrastructural alterations of E. coli’s mechanism of actions were translated and depicted. This study could be reference for characterization studies for morphological and ultrastructural of E. coli upon exposure to antimicrobial agents.

Atomic-scale investigation of γ-Ga2O3 deposited on MgAl2O4 and its relationship with β-Ga2O3

Nominally phase-pure γ-Ga2O3 was deposited on (100) MgAl2O4 within a narrow temperature window centered at ∼470 °C using metal-organic chemical vapor deposition. The film deposited at 440 °C exhibited either poor crystallization or an amorphous structure; the film grown at 500 °C contained both β-Ga2O3 and γ-Ga2O3. A nominally phase-pure β-Ga2O3 film was obtained at 530 °C. Atomic-resolution scanning transmission electron microscopy (STEM) investigations of the γ-Ga2O3 film grown at 470 °C revealed a high density of antiphase boundaries. A planar defect model developed for γ-Al2O3 was extended to explain the stacking sequences of the Ga sublattice observed in the STEM images of γ-Ga2O3. The presence of the 180° rotational domains and 90° rotational domains of β-Ga2O3 inclusions within the γ-Ga2O3 matrix is discussed within the context of a comprehensive investigation of the epitaxial relationship between those two phases in the as-grown film at 470 °C and the same film annealed at 600 °C. The results led to the hypotheses that (i) incorporation of certain dopants, including Si, Ge, Sn, Mg, Al, and Sc, into β-Ga2O3 locally stabilizes the “γ-phase” and (ii) the site preference(s) for these dopants promotes the formation of “γ-phase” and/or γ-Ga2O3 solid solutions. However, in the absence of such dopants, pure γ-Ga2O3 remains the least stable Ga2O3 polymorph, as indicated by its very narrow growth window, lower growth temperatures relative to other Ga2O3 polymorphs, and the largest calculated difference in Helmholtz free energy per formula unit between γ-Ga2O3 and β-Ga2O3 than all other polymorphs.

Electron beam-induced demetallation of Fe, Co, Ni, Cu, Zn, Pd, and Pt metalloporphyrins: insights in e-beam chemistry and metal cluster formations.

Electron beams are versatile tools for nanoscale fabrication processes, however, the underlying e-beam chemistry remains in its infancy. Through operando transmission electron microscopy investigations, we elucidate a redox-driven cargo release of individual metal atoms triggered by electron beams. The chosen organic delivery molecule, tetraphenylporphyrin (TPP), proves highly versatile, forming complexes with nearly all metals from the periodic table and being easily processed in solution. A comprehensive cinematographic analysis of the dynamics of single metal atoms confirms the nearly instantaneous ejection of complexed metal atoms under an 80 kV electron beam, underscoring the system's broad versatility. Providing mechanistic insights, we employ density functional theory to support the proposed reductive demetallation pathway facilitated by secondary electrons, contributing novel perspectives to electron beam-mediated chemical reaction mechanisms. Lastly, our findings demonstrate that all seven metals investigated form nanoclusters once ejected from TPP, highlighting the method's potential for studying and developing sustainable single-atom and nanocluster catalysts.

In-depth insight into the structural properties of nanoparticulate NiO for CO sensing

The outstanding properties exhibited by the p-type NiO nanostructures can be greatly affected by morpho-structural and defect characteristics with constructive or competing effects. We have conducted an in-depth study on NiO nanoparticles obtained by hydrothermal synthesis and submitted to various thermal treatments, to monitor the evolution of their structural properties and the effect of the thermal history on their CO sensing. Correlated electron paramagnetic resonance and analytical transmission electron microscopy investigations evidenced an amount of up to 1 % metallic nickel clusters close to surface in the NiO nanoparticles calcined at 400 °C and 500 °C for 8 h. Subsequent annealing in vacuum and in air of the sample calcined at 400 °C resulted in different size distributions and morphology of the NiO nanoparticles and an increase/decrease of the nickel phase, respectively. Comparative CO sensing tests on the two pristine samples and on the sample calcined at 400 °C and further annealed in air at 500 °C for 2 h showed an increase in the baseline resistance of the later due to the decrease of free charge carriers induced by the dissolution of the nickel clusters. The overall CO sensing results show a strong dependence on the samples thermal history.

Highly Stable and Active Ru Clusters Supported on Boron Carbon Nitride for Acidic Water Oxidation

In recent years, metal oxides, such as IrO2, have been widely used in proton exchange membrane water electrolysis (PEMWE) because of their excellent catalytic activity and long-term stability [1]. However the high price and scarcity of these catalysts were not enough to meet the requirements of PEMWE [2]. Therefore, it is significant to explore novel electrochemically active, stable, and low-cost catalysts.In this paper, a uniformly dispersed Ru confined on boron carbon nitride support was synthesized and studied. The surface chemical states of Ru were tuned by the interaction between Ru and the active N in boron carbon nitrogen (BCN), forming a highly stable Ru-N bond. Benefiting from a graphene-like structure, the BCN-0.5Ru catalyst exhibited greater conductivity than RuO2. The strong interaction between Ru and the BCN support also allowed for accelerated charge transfer at the electrode interface.Transmission electron microscopy (TEM) investigations revealed that Ru clusters were uniformly dispersed on BCN (Figure 1a), and the particle size distributions (Figure 1b) showed that the Ru clusters possessed an average particle size of 4 nm. It suggests that the Ru nanoclusters on the BCN support had small particle sizes and a narrow particle size distribution. These results demonstrated that the BCN support helped disperse the Ru metal nanoclusters more homogeneously than what occurred when RuO2 was prepared via direct RuCl3 annealing. The electrochemical performance of oxygen evolution reaction (OER) for BCN-xRu catalysts in O2-saturated 0.5 M H2SO4 solution was evaluated. The BCN-0.5Ru catalyst demonstrates a low overpotential of 164 mV at a current density of 10 mA cm–2 and remains stable for 12 h in acidic electrolyte (Figure 1c). In contrast, RuO2 without any support fails in only 1 h (Figure 1c). We propose that the surface chemical states of Ru supported by BCN may play an important role in enhancing stability. This study provides insights into designing and synthesizing high-performance electrocatalysts for acidic OER.

Cold sintering of BaZr0.8Y0.2O3-ẟ ceramics: Phase formation and grain boundary properties

Electrochemical devices based on the proton conducting ceramic BaZrO3 have shown their immense potential for efficient energy conversion and gas separation processes at intermediate temperatures. A major drawback of this material class is the inevitably high sintering temperature, which is necessary to reach sufficient densities for gas tightness. Recently, cold sintering has been applied to densify BaZrO3 – BaCeO3 solid solutions at low temperatures using a partial dissolution of the Ce-rich phase. Here, we apply the method to BaZr0.8Y0.2O3-ẟ (BZY20), which is a Ce-free proton conducting ceramic. We show that densification by cold sintering is viable at temperatures between 150 °C and 250 °C under uniaxial pressures of 400 MPa and deionized water as a sintering aid. The dissolution of yttrium from BZY20 during cold sintering acts as the trigger for densification at low temperatures but forms Y(OH)3 as an instable side product. Therefore, we developed a two-step cold sintering process that adds an additional thermal treatment between 900 and 1100 °C directly after the cold sintering process to enable electrochemical characterization and transmission electron microscopy investigations.

Insight into grain boundaries with reduced liquid metal embrittlement susceptibility in a boron-added 3rd generation advanced high strength steel

The addition of boron to the advanced high-strength steels (AHSS) enhances grain boundary cohesion and can play a significant role in intergranular degradation phenomena such as Zn-assisted liquid metal embrittlement (LME). The objective of this study is to reveal a thorough understanding of the effect of B on LME behaviour, where the welding test results indicated substantial improvement even at relatively low B concentration. Here, we adopted the strategy of identifying LME-sensitive grain boundaries, followed by characterizing grain boundary chemistry. EBSD measurements and prior austenite grain (PAG) reconstruction provided strong evidence of intergranular LME crack propagation via PAGBs. Further transmission electron microscopy and energy dispersive X-ray spectroscopy investigations demonstrated an asymmetric Mn profile along the PAGB in B-free steel. Therefore, we propose that B addition and consequently, lower grain boundary energy appears to prevent Mn segregation. Based on our observation, we conclude that B seems to have the similar desired effect on Zn diffusion along the PAGBs and eventually mitigates Zn-assisted LME.

Quantitative study on the microstructural evolution and dimensional stability mechanism of 2024 Al alloy during long-term thermal cycling

During the start-stop process of high-precision instruments in service, the critical materials of instruments undergo thermal cycling, resulting in changes in microstructure and dimension. In this paper, the evolution and coupling effects of dislocations and precipitates within 2024 Al alloy during 500 cycles were investigated, and their influence on the dimensional change was quantitatively characterized and decoupling analyzed. Transmission Electron Microscopy (TEM)/aberration-corrected scanning TEM (CS-TEM), X-ray diffraction (XRD), and Three-Dimensional Atom Probe Tomography (3D-APT) were used for microstructural evolution analysis and quantitative statistics. The dislocation density increased from 3.32 × 1014 m−2 to 5.75 × 1014 m−2 after 500 cycles, which accelerated elemental diffusion and provided nucleation sites of precipitates, contributing to an increase in the number density of the S'/S phase from 1.04 × 1024 m−3 to 1.41 × 1024 m−3. Based on the quantitative statistics of precipitate types and corresponding volume fractions, the dimensional change induced by precipitate evolution was −1.25 × 10−4. The dimensional change caused by the free volume introduced by dislocation density was 3.32 × 10−6. Comparing these values with the experimental value of −1.94 × 10−4, it is clear that the precipitate evolution is the main factor that triggers the dimensional change.

In Situ TEM/STEM Investigation of Crystallization in Y3Al5O12:Ce at High Temperatures Inside a Transmission Electron Microscope.

Y3Al5O12:Ce (YAG:Ce) phosphors are extensively used in the field of white light-emitting diodes (LEDs) due to their efficient luminescent properties. To optimize the performance of YAG:Ce phosphors, a comprehensive understanding of their synthesis and structural evolution is essential. This paper presents a direct in situ transmission electron microscopy (TEM) /scanning TEM (STEM) investigation on the transformation process of a precursor comprising nanocrystalline CeO2 dispersed in an amorphous Y-Al oxide matrix into crystalline YAG:Ce particles. The study reveals that nanocrystalline CeO2 particles dissolve completely in the Y-Al oxide matrix at a temperature above 900 °C, while YAlO3 (YAP)-type crystalline particles with Al2O3 phase in grain boundaries are observed above 1000 °C. Finally, YAG:Ce-type crystalline particles are formed above 1180 °C. Atomic-resolution energy-dispersive X-ray spectroscopy (EDS) elemental mapping demonstrates that the doped cerium (Ce) atoms occupy the same atomic sites as yttrium (Y). Photoluminescence measurements validate the efficient luminescent properties of the obtained YAG:Ce phosphor.

Dielectric, conductivity properties, elastic moduli, and gamma-ray attenuation abilities: A wide-ranging investigation into Molybdenum added ferrite nanoparticles

The auto combustion technique was employed to synthesis magnesium nano ferrite (MgMoxFe2-xO4). The impact of Mo-doped on the crystal’s structural, morphological, and elastic properties were inspected by applying x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Fourier transform infrared (FTIR) spectroscopy techniques. Pursuant to the XRD analysis, all samples have a cubic structure with single-phase. The average crystallite size was identified to be in the nanometer range confirmed by SEM and TEM investigations. FTIR data was implemented to assign the force constants of the octahedral and tetrahedral sites. Elastic moduli including the Poisson ratio, Young’s modulus, bulk modulus, and rigidity modulus have been estimated. The division of elastic moduli for all synthesized concentrations was interpreted using binding forces between ions of the cubic lattice spinel. Over and above, the AC conductivity (σ AC) and dielectric properties and their frequency dependence were investigated for the nano ferrites samples as a function of dopant Mo content and temperature. Finally, the radiation shielding capacities of the proposed samples against gamma and fast neutron radiation have been assessed. The findings reveal that the higher the Mo content, the lower the value of the mass attenuation coefficient. There is no significant diversity between the obtained mass attenuation coefficients for the nano and the micro. Among the samples investigated in this study, the highest Mo concentration sample had the largest fast neutron removal cross-section.

Room‐Temperature Synthesis of a Compositionally Complex Rare‐Earth Carbonate Hydroxide and its Conversion into a Bixbyite‐Type High‐Entropy Sesquioxide

AbstractIn the present work, the solvent‐deficient synthesis of the high‐entropy rare‐earth carbonate hydroxide RE(CO3)(OH) (RE=La, Ce, Pr, Nd, Sm, and Gd) and its thermal conversion into bixbyite‐type sesquioxide RE2O3 are reported for the first time. The high‐entropy rare earth carbonate hydroxide was prepared via mechanochemical reaction of the corresponding metal nitrate hydrates with ammonium hydrogen carbonate followed by the removal of the NH4NO3 by‐product. Calcination of the carbonate hydroxide precursor in ambient atmosphere at temperatures in the range from 500 to 1000 °C led to the high‐entropy rare earth sesquioxide which exhibited a bixbyite‐type structure ( ) independent of the calcination temperature. Transmission electron microscopy (TEM) investigation revealed the homogeneous distribution of all six rare earth cations in the high‐entropy sesquioxide lattice, however, with some compositional variation between individual grains. The bixbyite‐type structure may be considered as the result of heavy doping of the fluorite‐type CeO2 lattice with the other rare earth cations, which leads to a high concentration of oxygen vacancies, as revealed by electron diffraction and Raman spectroscopy data. The solvent‐deficient synthesis method used in the present study is considered as a valuable, straightforward and easily up‐scalable method to synthesize compositionally complex oxide ceramics.

TEM investigation of helium bubble evolution in tungsten and ZrC-strengthened tungsten at 800 and 1000°C under 40keV He+ irradiation

Helium-induced defect nucleation and accumulation in polycrystalline W and W0.5 wt%ZrC (W0.5ZrC) were studied in-situ using the transmission electron microscopy (TEM) combined with 40 keV He+ irradiation at 800 and 1000°С at the maximum damage level of 1 dpa. Radiation-induced dislocation loops were not observed in the current study. W0.5ZrC was found to be less susceptible to irradiation damage in terms of helium bubble formation and growth, especially at lower temperature (800 °C) when vacancies were less mobile. The ZrC particles present in the W matrix pin the forming helium bubbles via interaction between C atom and neighbouring W atom at vacancies. This reduces the capability of helium to trap a vacancy which is required to form the bubble core and, as a consequence, delays, the bubble nucleation.At 1000 °C, significant bubble growth occurred in both materials and all the present bubbles transitioned from spherical to faceted shape, whereas at 800 °C, the faceted helium bubble population was dominated in W.

Defect Structure of α-Ga2O3 Film Grown on a m-face Sapphire Substrate, According to Transmission Electron Microscopy Investigation

Defect Structure of α-Ga2O3 Film Grown on a m-face Sapphire Substrate, According to Transmission Electron Microscopy Investigation

Alfalfa vein mottling virus, a novel potyvirid infecting Medicago sativa L.

BackgroundWe have recently identified a novel virus detected in alfalfa seed material. The virus was tentatively named alfalfa-associated potyvirus 1, as its genomic fragments bore similarities with potyvirids. In this study, we continued investigating this novel species, expanding information on its genomic features and biological characteristics.MethodsThis research used a wide range of methodology to achieve end results: high throughput sequencing, bioinformatics tools, reverse transcription-polymerase chain reactions, differential diagnostics using indicator plants, virus purification, transmission electron microscopy, and others.ResultsIn this study, we obtained a complete genome sequence of the virus and classified it as a tentative species in the new genus, most closely related to the members of the genus Ipomovirus in the family Potyviridae. This assumption is based on the genome sequence and structure, phylogenetic relationships, and transmission electron microscopy investigations. We also demonstrated its mechanical transmission to the indicator plant Nicotiana benthamiana and to the natural host Medicago sativa, both of which developed characteristic symptoms therefore suggesting a pathogenic nature of the disease.ConclusionsConsistent with symptomatology, the virus was renamed to alfalfa vein mottling virus. A name Alvemovirus was proposed for the new genus in the family Potyviridae, of which alfalfa vein mottling virus is a tentative member.

Effect of High-Temperature Tempering on Microstructure and Mechanical Strength of Laser-Welded Joints between Medium-Mn Stainless Steel and High-Strength Carbon Steel

The strengthening effect due to high-temperature tempering (HTT) at 700 °C on the microstructure and mechanical properties of welded joints between medium-Mn stainless steel (MMnSS) and high-strength carbon steel (CS) was studied. The microstructure of the weldments was investigated using Laser and scanning electron microscopes. An Electron probe microanalyzer (EPMA) was used to assess quantitatively the elemental distribution profiles of alloying elements within the weld zone. The strengthening precipitates induced during welding and HTT were characterized by transmission electron microscopy (TEM). Uniaxial tensile tests and microindentation hardness (HIT) measurements of the weld joints were conducted to evaluate the strengthening effect. Fully fresh-martensite and fine-tempered martensitic structures were promoted in the as-weld and HTT processes, respectively. The HTT structure exhibited a remarkable improvement in mechanical properties (a better combination of yield and tensile strength together with moderate ductility) compared to its weld counterpart. TEM investigation revealed that various types of precipitates have been promoted in the structures of the weld and HTT, e.g., nanosized vanadium and chromium carbides. It is apparent that the proposed HTT of the joints is an effective treatment for improving the mechanical properties due to inducing the formation of fine interphase precipitates, resulting in enhanced mechanical strength of the joints.

Microstructure and electrical property of composite Co-W/CuO multilayered oxide coating for solid oxide fuel cell interconnector

To overcome the challenges related to the electrical resistance owing to the growth of the Cr-containing oxide layer in the SOFC system at high temperature, a composite coating of Co-W/CuO was fabricated on ferritic stainless steel for interconnectors by composite electroplating and pre-oxidation treatment. Compared to the Co-W alloy coating, the addition of CuO led to the formation of Cu-Co spinels and Cu-W composites, which affected the surface microstructure of the coating. Scanning electron microscopy with energy-dispersive spectroscopy (SEM-EDS) and transmission electron microscopy (TEM) investigations shows that CuWO4 nano-particles formed in the Cr-rich layer beneath the CoWO4 layer, of which the lattice deviation leads to the formation of oxygen vacancies. The CuWO4 acted as conductive pathways, reducing the electrical resistance. Long-term oxidation exposure further demonstrated that the Co-W/CuO coated SUS 430 exhibited a stable electrical conductivity of 10.23 mΩ cm2.

Antimicrobial efficacy of aloe-emodin mediated photodynamic therapy against antibiotic-resistant Pseudomonas aeruginosa in vitro

Multidrug-resistant Pseudomonas aeruginosa is a common pathogen that causes topical infections following burn injuries. Antimicrobial photodynamic therapy (aPDT) has emerged as a promising approach for treating antibiotic-resistant bacterial infections. The objective of this study was to evaluate the aPDT efficacy of aloe-emodin (AE), which is a photosensitizer extracted from traditional Chinese herbs, on antibiotic-sensitive and antibiotic-resistant P. aeruginosa in vitro.In this study, we confirmed the effectiveness of AE-mediated aPDT against both standard and MDR P. aeruginosa, explored the effects of irradiation time and AE concentration on bacterial survival in AE-mediated aPDT, and observed the structural damage of P. aeruginosa by using transmission electron microscope. Our results showed that neither AE nor light irradiation alone caused cytotoxic effects on P. aeruginosa. However, AE-mediated aPDT effectively inactivated both antibiotic-sensitive and antibiotic-resistant P. aeruginosa. The transmission electron microscope investigation showed that aPDT mediated by AE primarily caused damage to the cytoplasm and cell membrane.Our findings suggest that AE is a photosensitizer in the aPDT of MDR P. aeruginosa-caused topical infections following burn injuries. Future investigations will concentrate on the safety and efficacy of AE-mediated aPDT in animal models and clinical trials.

Adhesion of WTi to polyimide measured by complementary methods

Quantification of thin film adhesion to their substrates is crucial to ascertain reliable multi-material components, which are typically encountered in technologically relevant structures such as microelectronic devices. Metal-polymer interfaces have gained increased attention in the past since they open a new research field towards developing flexible electronic devices, yet their quantification is often experimentally challenging since standard routes to assess adhesion such as nanoindentation-based techniques or four-point bending may not be applicable due to lack of rigidity. In the present study interface adhesion of nominally 150 nm thin WTi films sputtered onto polyimide, part of a multi-material stack consisting of brittle and compliant materials, was determined experimentally. Upon contactless removal of the bilayer by etching a sacrificial layer, originally part of the multilayer stack, the WTi film showed cracks and buckles, which could be characterized by atomic force and confocal laser scanning microscopy. Hence, two models to quantify adhesion were compared: the model of tensile induced delamination – typically employed for metal films on compliant substrates – and the model of Hutchinson and Suo, which is usually applied on spontaneously formed, straight buckles. The first model reveals adhesion values for the native WTi-polyimide interface of 2.4 ± 0.8 J/m2 and the latter model 4.7 ± 2.3 J/m2. The slight difference in adhesion results, which are both rooted in the same theory, could be rationalized by the fact that the model for tensile induced delamination gives a measure of the lower bound of the adhesion energy. The overall rather lower adhesion values could be explained by additional transmission electron microscopy investigations conducted on the cross section of the interface, which reveals no interlinking morphology and a flat interface.

Advanced approach of bulk (111) 3C-SiC epitaxial growth

3C-SiC films grown on (111) Si substrates exhibit poor crystal quality and experience wafer cracks and bowing preventing access to bulk growth. This work reports innovative Chemical Vapor Deposition (CVD) growth methodology on 4 in. Si substrates which allowed the growth of 230 mm thick layer of (111) 3C-SiC through the melting of the Si substrate in the CVD chamber and the adoption of the resulting free standing 3C-SiC for the growth of bulk (111) 3C-SiC layer under high N fluxes. From the molten KOH etching and subsequent SEM investigation it has been ascertained that with a N2 flux of 1600 sccm there is a significant reduction in the concentration of stacking faults (SFs) from (7.16 ± 0.04) × 103 cm−1 to (0.4 ± 0.3) × 103 cm−1. This reduction is consistent with the cross section m-PL response displaying steep and uniform increase in the intensity of the band-edge signal a factor 10 higher on the surface with respect to the equal (100) 3C-SiC grown thickness. Furthermore, the emission attributed to point defects is considerably lower in (111) 3C-SiC. From Scanning Transmission Electron Microscopy (STEM) investigation it appears evident how the typical mechanism valid in (100) growths consisting in the mutual closure of SFs coming from opposing {111} planes that give rise to Lomer and l-shaped dislocations is replaced by a different panorama of evolution. Indeed, it is shown how the SFs shred but do not interrupt each other during growth. Furthermore, dropping in the number of atomic planes composing SFs layers appears to be a key phenomenon leading to both the shrinkage of the number of SF atomic layers as well as to the SF self-closure. High Angle Annular Dark Field-Scanning Transmission Electron Microscopy (HAADF-STEM) attested how the crystal tends to smooth out the lattice mismatch until the SF is suppressed. Because of the foregoing, the mechanisms of evolution of the defects in (111) 3C-SiC revealed in this study, demonstrates how the growth parameters must be matched with the kinetics of the defects in order to endorse (111) 3C-SiC adoption in high performing devices.