Transference Number Research Articles

Anion trapping-coupling strategy driven asymmetric nonflammable gel electrolyte for high performance sodium batteries

Gel polymer electrolytes, promising electrolyte candidates for advanced sodium metal batteries (SMBs), suffer from the great challenges of combustion risk and inferior interfacial stability caused by poor mechanical properties and low Na+ selectivity. Herein, we proposed a rational anion trapping-coupling strategy to build a mechanically robust asymmetric nonflammable composite gel electrolyte (AS-NFCGE) by introducing in-situ coupled boron nitride nanosheets (BNNs) on glass fiber matrix embedded with synchronous polymerized flame-retardant polymer. Theoretical calculations, finite-element simulations, and experimental tests prove that the high coupling BNNs with anion trapping effect constructed asymmetric structure can significantly accelerate selective Na+ migration kinetics, enhance mechanical properties of AS-NFCGE and endow a similar single-ion conducting behavior to homogenize ion-distribution at the anode side, thus improving interfacial stability and suppressing dendrite growth to achieve ultra-stable SMBs. Specifically, the AS-NFGE delivers high ionic conductivity and Na+ transference number (0.73) together with excellent flam-retardant. Consequently, the dendrite-free Na/Na symmetric cell exhibits considerable cycling life for over 3000 h at 0.1 mA cm−2 with low overvoltage. Applications of the AS-NFCGE in SMBs further demonstrate the excellent electrochemical performances, and no thermal runaway and no electrolyte leakage occur for pouch cells using AS-NFCGE. This strategy provides new insight into the development of safe and high-energy SMBs and the beyond.

Development and analysis of the physical and electrochemical characteristics of a nano titanium (IV) tungstomolybdate supported on polyethersulfone composite cation exchange membrane

In this study, a series of novel composite membranes were synthesized utilizing polyethersulfone (PES), sulfonated polyethersulfone (SPES) as base polymer and titanium tungstomolybdate (TWM) as an inorganic ion exchange resin. The membranes were fabricated through the solution casting technique. The composite membranes exhibited enhanced thermal and chemical stability, as well as improved oxidative stability. All the composite membranes demonstrated higher hydrophilicity, with the SPES-TWM composite membranes displaying the lowest contact angle of 65°. The composite membranes also displayed favorable water uptake (up to 26% for SPES-TWM) and lower methanol uptake (maximum 12% for SPES-TWM) and better mechanical stability (maximum of 40 MPa for SPES-TWM). The SPES-TWM composite membranes exhibited the maximum ion exchange capacity of 1.32 meq.g−1. The transport number of 0.95 was obtained for SPES-TWM, which is comparable to the Nafion-117 membrane. The proton conductivity of both membranes increased as the temperature increased. The maximum proton conductivity of 6.3 mScm−1 was observed for SPES-TWM at 60 °C.

Variant-Localized High-Concentration Electrolyte without Phase Separation for Low-Temperature Batteries.

Dual-ion batteries (DIBs) present great application potential in low-temperature energy storage scenarios due to their unique dual-ion working mechanism. However, at low temperatures, the insufficient electrochemical oxidation stability of electrolytes and depressed interfacial compatibility impair the DIB performance. Here, we design a variant-localized high-concentration solvation structure for universal low-temperature electrolytes (ν-LHCE) without the phase separation via introducing an extremely weak-solvating solvent with low energy levels. The unique solvation structure gives the ν-LHCE enhanced electrochemical oxidation stability. Meanwhile, the extremely weak-solvating solvent can competitively participate in the Li+-solvated coordination, which improves the Li+ transfer kinetics and boosts the formation of robust interphases.Thus, the ν-LHCE electrolyte not only has a good high-voltage stability of >5.5 V and proper Li+ transference number of 0.51 but also shows high ionic conductivities of 1 mS/cm at low temperatures. Consequently, the ν-LHCE electrolyte enables different types of batteries to achieve excellent long-term cycling stability and good rate capability at both room and low temperatures. Especially, the capacity retentions of the DIB are 77.7% and 51.6 %, at -40 oC and -60 oC, respectively, indicating great potential for low- andtemperature energy storage applications, such as polar exploration,emergency communication equipment, and energy storage station in cold regions.

Novel PEO-based Solid Polymer Electrolyte with High Elasticity and High Ionic Conductivity for Room Temperature Lithium Metal Batteries

Abstract The development and application of polyethylene oxide (PEO) based solid polymer electrolyte (SPE) is severely constrained by its low ionic conductivity and poor tensile resistance. To improve the electrochemical performance of SPE without losing its mechanical properties, a benzene sulfonate-based additive is adopted into crosslinking system composed of -CH2-CH2-O- segments to obtain a membrane with a high ionic conductivity of 1.47×10-4 S cm-1 and an ionic transference number of 0.70 at room temperature. The activation energy value of 0.128 eV gives evidence for a favorable migration mechanism of PTH-SPE. Anti-dendrite growth and contact optimization can be realized by molecular structure design with a tensile elongation of 490%. The reversible overpotential of Li||Li symmetric cell within 1000 h demonstrates that the compact PTH-SPE can inhibit the growth of lithium dendrite. This work provides a new strategy for designing high-performance solid electrolytes for room temperature via a green solvent-free method.

Three-Component Construction of Mesoporous Metal-Organic Frameworks and Their Incorporation into Solid Polymer Electrolytes for Li-Ion Conduction.

Solid electrolytes with high ionic conductivity and satisfactory electrochemical stability are essential for the development of solid-state batteries. However, current strategies, including polymer (and polymer-based composite) electrolytes, still face challenges in meeting the bar set by real operations. We seek to improve the Li-ion conduction of the electrolytes by incorporating mesoporous metal-organic frameworks (MOFs) into the polymer matrix. Specifically, MOFs with pores larger than 3.0 nm are constructed by three-component reactions that involve the construction of both coordinative and dynamic imine linkages. The MOFs allow polymer penetration and amorphization and efficient lithium salt dissociation in the confined channels. Numerous metal sites and organic functionalities in the MOF backbone further assist the ion migration by providing strong interactions with the fluorinated polymer and the Li+. Remarkable ionic conductivity (0.95 mS cm-1) and a large lithium transference number (0.64) are achieved. Overall, the study fully utilizes both the MOF structural units with atomic precision and the encompassed space at the mesoscale for solid-state electrolyte development.

Coconstruction of Supramolecular Lithium-Conducting Cross-Linked Networks Based on PVDF and Triblock Polymer Nanomicrosphere Solid-State Polymer Electrolytes for Lithium-Metal Batteries.

Uneven lithium plating and low ionic conductivity currently impede the realization of high-capacity rechargeable lithium metal batteries. And the conventional poly(ethylene oxide) (PEO) solid-state electrolytes are unsuitable for high-energy-density Li anode applications due to their low lithium-ion transference number and high reactivity with Li metal, leading to detrimental dendrite formation and potentially hazardous exothermic reactions with the electrolyte. In this study, we employ a supramolecular approach to develop a novel polymer solid-state electrolyte based on poly(vinylidene fluoride) (PVDF) and a novel triblock polymer nanomicrosphere, (poly(ε-caprolactone)-poly(ethylene glycol)-poly(ε-caprolactone), (PCL-PEG-PCL). The abundance of carbonyl and ether-oxygen functional groups in PCL-PEG-PCL enhances the lithium coordination environment within the polymer solid-state electrolyte. Additionally, the original C-F moieties of PVDF form hydrogen bonds with C-H and terminal hydroxyl groups in PCL-PEG-PCL, collectively creating a multichannel fast Li+-conducting supramolecular cross-linked network. The resulting electrolyte demonstrates a high ionic conductivity of 1.4 × 10-3 S cm-1 and an extended electrochemical window of 5.2 V. Moreover, the electrolyte exhibits a high lithium-ion transference number (tLi+ = 0.63) at room temperature and exhibits excellent interfacial compatibility with the lithium metal anode. For the resulting electrolyte utilized in LiFePO4 batteries, the capacity retention of the cells assembled with this electrolyte exceeds 91.3% after 1000 cycles at 25 °C and 2 C (0.281 mA cm-2).

Design a polymer-based composite electrolyte with high ionic conductivity for high-performance lithium-metal batteries

Constructing a stable and robust solid polymer electrolyte (SPE) is crucial for achieving dendrite-free lithium-metal anodes and high-performance lithium batteries. However, realizing the integrity of solid electrolytes with high ion conductivity during long-life cycling under high current density remains a significant challenge. In this study, we propose a multifunctional SPE with a polyvinylidene fluoride (PVDF)/co-polyphenol coordination polymer (EACo2) hybrid composite to improve the durability of Li metal anode during repeat plating/stripping cycles by using a facile solution-casting method. The PVDF as a substrate with high mechanical strength and improved lithiophilicity exhibits high ionic conduction and excellent dendrite inhibition ability; meanwhile, the EACo2 fillers with a high density of Lewis-acidic sites contribute to the dissociation of lithium salts and decrystallization of the PVDF, resulting in a high Li-ion transference number and ion conductivity (2.66 × 10−3 S cm−1 at 30 ℃). The symmetrical cells with PVDF/EACo2 SPE can stabilize cycling over 1200 hours at a deposition capacity of 0.1 mAh cm−2. Moreover, the assembled full cells Li|LiFePO4 demonstrate long-term stability (1000 cycles at 1 C) with impressive capacity retention of 75 %, offering a promising approach towards high-performance lithium metal batteries.

Functionalized polypropylene separator coated with polyether/polyester blend for high-performance lithium metal batteries

Commercial polyolefin separators used in lithium metal batteries (LMBs) have the disadvantages of insufficient thermal stability and poor wettability with electrolytes, which causes bad safety and battery performance. Poly(ε-caprolactone) (PCL)-based electrolytes have drawn widespread attention in the field of polymer electrolytes owing to their electrochemical stability and high lithium-ion transference number. This work proposes a strategy of functionalizing commercial polypropylene (PP) separator coated by blending PCL (M w ~ 50,000) and poly(ethylene oxide) (PEO, M V ~ 600,000). Compared to commercial PP separators, PP-blended PEO60w/PCL5w separators possess better wettability with electrolytes and electrochemical performances. The initial discharge specific capacity of LiFePO4-based LMBs assembled with PP-blended PEO60w/PCL5w separators reaches 144 mAh g-1 (1C) and 103 mAh g-1 (5C) at room temperature, respectively. Notably, Li/PP-blended PEO60w/PCL5w/LiFePO4 shows an improved capacity retention rate of 77% after 800 cycles, confirming that the functionalized separator with coated PEO/PCL blend has great potential for application in the field of LMBs.

Self‐Extinguishing and Low‐Cost Quasi‐Solid Polymer Electrolyte for Room Temperature Lithium Metal Batteries

Most modification strategies of polyethylene oxide (PEO)‐based solid polymer electrolyte focus on improving the room temperature ionic conductivity, while disregarding its inherent flammability that poses substantial safety hazard. Herein, a self‐extinguishing quasi‐solid‐state polymer electrolyte (PTTF‐SPE), which combines excellent room temperature electrochemical properties and high safety, has been developed by introducing triethyl phosphate (TEP) as a low‐cost and highly effective flame retardant. The cross‐linking structure derived from ‐CH2‐CH2‐O‐ segments of tetramethylene glycol dimethyl ether (TEGDME) and PEO makes a contribution to a high amorphous state of polymer. A robust solid electrolyte interphase (SEI) formed by preferential decomposition of fluoroethylene carbonate (FEC) that acts as a film‐forming additive, which can prevent TEP from degradation at lithium metal anode. The optimized PTTF‐SPE exhibits high ionic conductivity (0.54×10‐3 S/cm) and lithium transference number (0.71) at room temperature. The LiFePO4||Li battery demonstrates excellent cycle life over 500 cycles at 0.5 C with a high average discharge capacity of 131 mAh/g. A symmetric Li||Li battery that operating for 850 hours indicates a good compatibility of PTTF‐SPE towards lithium metal. This work provides a new idea for developing high‐energy‐density and high‐safety lithium‐metal batteries (LMBs) for room temperature.

News/Resources

Self‐esteem, teamwork go hand‐in‐hand, study shows Notre Dame allocates $68M to mental health initiatives Transfer numbers increase Study links disability, incarceration

Opening and Constructing Stable Lithium‐ion Channels within Polymer Electrolytes

Lithium‐ion batteries play an integral role in various aspects of daily life, yet there is a pressing need to enhance their safety and cycling stability. In this study, we have successfully developed a highly secure and flexible solid‐state polymer electrolyte (SPE) through the in‐situ polymerization of allyl acetoacetate (AAA) monomers. This SPE constructed an efficient Li+ transport channel inside and effectively improved the solid‐solid interface contact of solid‐state batteries to reduce interfacial impedance. Furthermore, it exhibited excellent thermal stability, an ionic conductivity of 3.82×10‐4 S cm‐1 at room temperature (RT), and a Li+ transport number (tLi+) of 0.66. The numerous oxygen vacancies on layered inorganic SiO2 created an excellent environment for TFSI‐ immobilization. Free Li+ migrated rapidly at the C=O equivalence site with the poly(allyl acetoacetate) (PAAA) matrix. Consequently, when cycled at 0.5 C and RT, it displayed an initial discharge specific capacity of 140.6 mAh g‐1 with a discharge specific capacity retention rate of 70% even after 500 cycles. Similarly, when cycled at a higher rate of 5 C, it demonstrated an initial discharge specific capacity of 132.3 mAh g‐1 while maintaining excellent cycling stability.

Conformally reactive interphase enables excellent kinetics and cyclability in quasi-solid-state sodium metal battery

The rational design of flexible and robust anode-electrolyte interface is of great significance for extending the cycle life and improving the kinetics performance for sodium metal batteries (SMBs). Herein, a conformally reactive solid-electrolyte interphase (SEI) is constructed through a spontaneous absorption-oligomerization strategy in a quasi-solid-state polymer electrolyte (QSE-T). The polymeric network in the QSE-T system ensures a stable environment with high Na+ transfer number to suppress Na dendrite growth and chemical corrosion. Simultaneously, the reactive SEI is consisted of inorganic NaF and low crosslinked O-B-O and O-B-F segments derived from the 4-trifluoromethylphenylboronic acid (TFPBA) additive, which exhibits lower Na+ diffusion-barriers, and accommodates the ever-changing quasi-solid interface during cycling. Consequently, the NVP||QSE-T||Na cells exhibit ultra-stable cycling performance and high rate capability, with a high initial capacity of 95.1 mAh g−1 at a high rate of 5 C and a capacity retention rate of 86.6 % after 12,000 cycles.

Reimagining care: effectiveness of modifying an adolescent eating disorder intensive service.

The COVID-19 pandemic prompted a surge in adolescent eating disorders and rapid changes in the delivery of intensive community treatments. This study investigates the modification from a group-based day programme to an intensive family treatment approach. A retrospective chart review was performed on data from 190 patients who accessed the intensive service for anorexia nervosa in the past 6 years. Outcomes from the traditional model were compared with the new intensive family model, namely length of admission, percentage median body mass index difference and transfers to in-patient services. There was a significant reduction in the length of intensive treatment (from 143.19 to 97.20 days). The number of transfers to specialist eating disorder in-patient services also significantly reduced, and is decreasing year on year. The findings hold particular relevance as intensive services for adolescent eating disorders continue to be established within health services, with no clear unified approach to treatment.

Modulating Electron Transfer between Pt and MOF Support through Pd Doping Promotes Nanozyme Catalytic Efficiency.

Electron transfer is considered to be a typical parameter that affects the catalytic activity of nanozymes. However, there is still controversy regarding whether higher or lower electron transfer numbers are beneficial for improving the catalytic activity of nanozymes. To address this issue, we propose the introduction of Pd doping as an important electron regulation strategy to tune electron transfer between Pt and ZIF-8 carriers (PtxPd1@ZIF-8). We observe a volcano-shaped relationship between the electron transfer number and catalytic activity, reaching its peak at Pt4Pd1@ZIF-8. Mechanism studies indicate that as the electron transfer number from Pt to ZIF-8 carriers increases, the d-band center of the active site Pt increases, reducing the occupancy of antibonding states and enhancing the adsorption capacity of the key intermediate (*O). However, a further increase in the adsorption of *O energy makes it difficult to desorb and participate in the next reaction, thus exhibiting volcanic activity. The optimized Pt4Pd1@ZIF-8 nanozyme is applied to develop an immunoassay for the detection of zearalenone, achieving a detection limit of 0.01 μg/L, which is 6 times higher than that of the traditional enzyme-linked immunosorbent assay. This work not only reveals the potential regulatory mechanism of electron transfer on the catalytic activity of nanozymes but also improves the performance of nanozyme-based biosensors.

A Large-Scale Fabrication of Flexible, Ultrathin, and Robust Solid Electrolyte for Solid-State Lithium-Sulfur Batteries.

All-solid-state lithium metal batteries (ASSLMBs) are considered as the most promising candidates for the next-generation high-safety batteries. To achieve high energy density in ASSLMBs, it is essential that the solid-state electrolytes (SSEs) are lightweight, thin, and possess superior electrochemical stability. In this study, a feasible and scalable fabrication approach to construct 3D supporting skeleton using an electro-blown spinning technique is proposed. This skeleton not only enhances the mechanical strength but also hinders the migration of Li-salt anions, improving the lithium-ion transference number of the SSE. This provides a homogeneous distribution of Li-ion flux and local current density, promoting uniform Li deposition. As a result, based on the mechanically robust and thin SSEs, the Li symmetric cells show outstanding Li plating/stripping reversibility. Besides, a stableinterfacecontact between SSE and Li anode has been established with the formation of an F-enriched solid electrolyte interface layer. The solid-state Li|sulfurized polyacrylonitrile (Li|SPAN) cell achieves a capacity retention ratio of 94.0% after 350 cycles at 0.5 C. Also, the high-voltage Li|LCO cell shows a capacity retention of 92.4% at 0.5 C after 500 cycles. This fabrication approach for SSEs is applicable for commercially large-scale production and application in high-energy-density and high-safety ASSLMBs.

Alumina - Stabilized SEI and CEI in Potassium Metal Batteries.

Aluminum oxide (Al2O3) nanopowder is spin-coated onto both sides of commercial polypropene separator to create artificial solid-electrolyte interphase (SEI) and artificial cathode electrolyte interface (CEI) in potassium metal batteries (KMBs). This significantly enhances the stability, including of KMBs with Prussian Blue (PB) cathodes. For example, symmetric cells are stable after 1,000 cycles at 0.5 mA/cm2 - 0.5 mAh/cm2 and 3.0 mA/cm2 - 0.5 mAh/cm2. Alumina modified separators promote electrolyte wetting and increase ionic conductivity (0.59 vs. 0.2 mS/cm) and transference number (0.81 vs. 0.23). Cryo-stage focused ion beam (cryo-FIB) analysis of cycled modified anode demonstrates dense and planar electrodeposits, versus unmodified baseline consisting of metal filaments (dendrites) interspersed with pores and SEI. Alumina-modified CEI also suppresses elemental Fe crossover and reduces cathode cracking. Mesoscale modeling of metal - SEI interactions captures crucial role of intrinsic heterogeneities, illustrating how artificial SEI affects reaction current distribution, conductivity and morphological stability.

Building Flame-Retardant Polymer Electrolytes via Microcapsule Technology for Stable Lithium Batteries.

Flame retardants could improve the safety properties of lithium batteries (LBs) with the sacrifice of electrochemical performance due to parasitic reactions. To concur with this, we designed thermal-response clothes for hexachlorophosphazene (HCP) additives by the microcapsule technique with urea-formaldehyde (UF) resin as the shell. HCP@UF combines with polyacrylonitrile (PAN) by hydrogen bonds successfully to form PAN-HCP@UF as the flame-retardant solid polymer electrolyte. The hydrogen bonds ensure excellent mechanical properties of the polymer electrolyte. The multiscale free radical-annihilating agent HCP effectively eliminates hydrogen free radicals of electrolytes under high temperature, showing excellent flame retardation. During the operation of the battery, functional groups on the UF resin act as active sites to promote the migration of lithium ions, while the internal HCP is protected from electrochemical reaction. With 25% HCP@UF addition, the limiting oxygen index of the PAN-HCP@UF increases to 28% and the Li+ transfer number up to 0.80. By UF protection, the initial capacity retention rate of the Li||LFP battery that assembles with PAN-HCP@UF is 88.8% after 500 cycles at 0.5 C. Thus, the microcapsule-encapsulated approach is deemed to provide an innovative strategy to prepare high-safety solid-state LB with a stable long cycle life.

Alumina ‐ Stabilized SEI and CEI in Potassium Metal Batteries

Aluminum oxide (Al2O3) nanopowder is spin‐coated onto both sides of commercial polypropene separator to create artificial solid‐electrolyte interphase (SEI) and artificial cathode electrolyte interface (CEI) in potassium metal batteries (KMBs). This significantly enhances the stability, including of KMBs with Prussian Blue (PB) cathodes. For example, symmetric cells are stable after 1,000 cycles at 0.5 mA/cm2 ‐ 0.5 mAh/cm2 and 3.0 mA/cm2 ‐ 0.5 mAh/cm2. Alumina modified separators promote electrolyte wetting and increase ionic conductivity (0.59 vs. 0.2 mS/cm) and transference number (0.81 vs. 0.23). Cryo‐stage focused ion beam (cryo‐FIB) analysis of cycled modified anode demonstrates dense and planar electrodeposits, versus unmodified baseline consisting of metal filaments (dendrites) interspersed with pores and SEI. Alumina‐modified CEI also suppresses elemental Fe crossover and reduces cathode cracking. Mesoscale modeling of metal – SEI interactions captures crucial role of intrinsic heterogeneities, illustrating how artificial SEI affects reaction current distribution, conductivity and morphological stability.

Three-Dimensional Metal-Organic Framework@Cellulose Skeleton-Reinforced Composite Polymer Electrolyte for All-Solid-State Lithium Metal Battery.

High-safety and high-energy-density solid-state lithium metal batteries (SSLMBs) attract tremendous interest in both academia and industry. Especially, composite polymer electrolytes (CPEs) can overcome the limitations of single-component solid-state electrolytes. In this work, a strategy of combining a rigid functional skeleton with a soft polymer electrolyte to prepare reinforced CPEs was adopted. The in situ grown zeolitic imidazolate frameworks (ZIFs) with three-dimensional cellulose fiber skeleton (ZIF-67@CF) and succinonitrile (SN) plasticizer into poly(ethylene oxide) (PEO) together form ZIF-67@CF/PEO-SN CPEs. The addition of ZIF-67@CF and SN to PEO synergistically enhanced the physical and electrochemical properties of CPEs. Furthermore, the conduction mechanism of lithium-ion (Li+) in CPEs was studied using density functional theory. It is impressive that the ZIF-67@CF/PEO-SN CPEs at 30 °C exhibit a high ionic conductivity of 1.17 × 10-4 S cm-1, a competitive Li+ transference number of 0.40, a wide electrochemical window of 5.0 V, a notable tensile strength of 18.7 MPa, and superior lithium plating/stripping stability (>550 h at 0.1 mA cm2). Such favorable features endowed LiFePO4/(ZIF-67@CF/PEO-SN)/Li cell at 30 °C with a high discharging capacity (152.5 mA h g-1 at 0.2 C), a long cycling lifespan (>150 cycles with 99% capacity retention), and superior operating safety. This work provides insights and promotes the application of functionalized CPEs for SSLMBs.

Electrolytic performance of sodium alginate-poly vinyl alcohol matrix with ammonium bromide for proton conduction: Applications in electrochemical systems

Polymer blend electrolytes based on poly(vinyl alcohol) (PVA) and sodium alginate (NaAlg) were prepared using the solution casting method. These electrolytes were doped with varying amounts of ammonium bromide (NH4Br). The compatibility of NH4Br with PVA:NaAlg polymers was examined through X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) studies. The FTIR assessment confirmed the formation of a complex between PVA:NaAlg and the added salt, as evidenced by modifications and reductions in the intensity of FTIR bands related to functional groups. The conductivity and dielectric behavior of the samples were analyzed using AC impedance spectroscopy. The sample with 20 wt% of added salt exhibited a higher ionic conductivity of 1.661×10−5 Scm−1. Activation energy and relaxation time were estimated, and dielectric studies revealed a non-Debye nature. The conduction mechanism was best described by the correlated overlapping large polaron tunneling model (OLPT). The highest conducting sample was found to be suitable for electrochemical devices, as demonstrated by transference number (TNM), cyclic volumetric (CV), and linear sweep voltammetry (LSV) analyses. This high-conductivity sample can be employed in electrochemical devices such as EDLC. The cyclic voltammetry (CV) curve exhibited a nearly rectangular shape with non-faradaic peaks. GCD(Galvanostatic charge-discharge) analysis yielded specific capacitance, power density, and energy density values of 125.01 Fg−1, 1037 WKg−1, and 14.06 WhKg−1 respectively. These results indicate that polymer electrolytes show great promise as electrolytes in proton-conducting electrochemical devices.