Total Sediment Research Articles

Simulation of Bed Change in Al-Musayyab Canal using HEC-RAS Software

This study focuses on the simulation of the bed change and total sediment concentration in the Al-Musayyab Canal, which is a vital irrigation system located in the central region of Iraq, using HEC-RAS V 6.3 software. The 49.5 km canal, with 13 branches, faces challenges from sediment influx originating from the Euphrates River. The primary objective is to analyze sedimentation, erosion patterns, and sediment discharge variations to support effective canal management. Field sampling collected suspended and bed load samples for laboratory tests, providing input data for the sediment transport model. Simulation results show steady flow water surface elevations ranging from 26.32 to 33.16 m.a.s.l, with velocities from 0.24 to 0.98 m/s. Significant sediment deposition and erosion variations are observed as data for 2019 and 2020 are analyzed. Notable changes in the canal's invert levels occurred in both years, with maximum deposition depths reaching 14 cm in 2019 and 21 cm in 2020. Erosion depths ranged from 3 to 15 cm in 2019 and 5 to 25 cm in 2020. The total sediment discharge for 2019 in the Al-Musayyab Canal amounted to 17 tons/day, while 22 tons/day in 2020.

On the sediment deposition on Barugbug Situdam Weir

In this paper, we investigate the behavior of total sediment transport in the Barudbug weir, Situdam, Karawang, West Java, Indonesia, which is a crucial aspect of water management in the Citarum river basin. We utilize SESAME instrument observation data, encompassing rainfall, TSS, and depth parameters, gathered over a period of approximately three years. Additionally, we employ a two-dimensional Advection-Diffusion analytic model that takes into account settling velocity. The observation results reveal a positive correlation between TSS and depth, with TSS levels increasing following heavy rainfall. Furthermore, there exists a time delay between rainfall events and the subsequent rise in TSS concentration, suggesting an upstream source of sediment. The model outcomes demonstrate an inverse relationship between TSS concentration and the velocity of river flow, as the river flow acts as a leaching mechanism.

Cost-effectiveness of erosion mitigation to meet water clarity targets in the Manawatū-Whanganui Region of New Zealand

Soil erosion is a significant environmental issue worldwide. It affects water quality, biodiversity, and land productivity. New Zealand government agencies and regional councils work to mitigate soil erosion through policies, management programmes, and funding for soil conservation projects. Information about cost-effectiveness is crucial for planning, targeting, and implementing erosion mitigation to achieve improvements in sediment-related water quality. While there is a good understanding of the costs of erosion mitigation measures, there is a dearth of literature on their cost-effectiveness in reducing sediment loads and improving water quality at the catchment level. In this study, we estimate the cost-effectiveness of erosion mitigation measures in meeting visual water clarity targets. The analysis utilizes the spatially explicit SedNetNZ erosion process and sediment budget modelling in the Manawatū-Whanganui Region and region-specific mitigation costs. The erosion mitigation measures considered in the analysis include afforestation, bush retirement, riparian retirement, space-planted trees, and gully tree planting. We modelled two scenarios with on-farm erosion mitigation implemented across the region from 2021 to 2100, resulting in a 48% and 60% reduction of total sediment load. We estimate the marginal costs to achieve the visual national bottom line for water clarity, as assessed by the length of waterways that meet the clarity targets. We also estimate the marginal costs of improving average water clarity, which can be linked with non-market valuation studies when conducting a cost-benefit analysis. We find that gully tree planting and space-planted trees are the most cost-effective mitigation measures and that riparian retirement is the least cost-effective. Moreover, cost-effectiveness is highly dependent on current land use and the biophysical features of the landscape. Our estimates can be used in cost-benefit analysis to plan and prioritize soil erosion mitigation at the catchment and regional levels.

Evaluating the long-term effects of best management practices on pollution reduction and soil quality improvement in sloping farmland of the Three Gorges Reservoir area

Reducing nonpoint-source pollution and improving soil quality by applying best management practices (BMPs) on sloping farmland are essential for ensuring water environmental safety and sustainable agricultural development. However, little is known about the accumulative effect of the long-term application of BMPs on reducing pollution and improving soil quality in major land use types of sloping farmland in watersheds. We conducted a nine-year field experiment for citrus orchard and cropland of sloping farmland in the Three Gorges Reservoir area of China. The treatment settings for the citrus experimental plots were as follows: (1) citrus intercropped with white clover (WC), (2) citrus orchard soil mulched with straw (SM), (3) citrus intercropped with Hemerocallis flava contour hedgerows (HF) and (4) conventional citrus planting pattern (C-CK). The treatment settings for the crop experimental plots were as follows: (1) wheat-peanut rotation intercropped with Toona sinensis contour hedgerows (TS), (2) wheat-peanut rotation intercropped with alfalfa contour hedgerows (AF), (3) ryegrass-sesame rotation (RS) and (4) conventional wheat-peanut rotation (W-CK). We found that compared with C-CK and W-CK, (1) runoff, sediment, total nitrogen and total phosphorus losses were reduced by 18.0 %, 66.1 %, 35.6 % and 40.2 %, respectively, in WC; by 22.4 %, 61.2 %, 43.9 % and 52.4 %, respectively, in SM; by 25.4%, 69.5 %, 52.0 % and 58.1 %, respectively, in HF; by 45.1 %, 73.7 %, 64.6 % and 66.0 %, respectively, in TS; by 41.8 %, 67.4 %, 59.3 % and 60.8 %, respectively, in AF; and by 24.1 %, 42.9 %, 39.3 % and 40.3 %, respectively, in RS; (2) the soil quality index values of the BMP treatments increased; and (3) the application of these BMPs did not significantly affect yield or product value. We suggest the application of these BMPs on sloping farmland to (1) efficiently reduce total runoff, total sediment, and soil total nitrogen and total phosphorus losses; (2) improve soil quality; and (3) have no significant effect on output, of which the BMP HF applied to citrus orchard and the BMP TS applied to cropland are the most effective.

A Comparative Analysis of Sediment Concentration Using Artificial Intelligence and Empirical Equations

Morphological changes in canals are greatly influenced by sediment load dynamics, whose estimation is a challenging task because of the non-linear behavior of the sediment concentration variables. This study aims to compare different techniques including Artificial Intelligence Models (AIM) and empirical equations for estimating sediment load in Upper Chenab Canal based on 10 years of sediment data from 2012 to 2022. The methodology involves utilization of a newly developed empirical equation, the Ackers and White formula and AIM including 20 neural networks with 10 training functions for both Double and Triple Layers, two Artificial Neuro-Fuzzy Inference System (ANFIS), Particle Swarm Optimization, and Ensemble Learning Random Forest models. Sensitivity analysis of sediment concentration variables has also been performed using various scenarios of input combinations in AIM. A state-of-the-art optimization technique has been used to identify the parameters of the empirical equation, and its performance is tested against AIM and the Ackers and White equation. To compare the performance of various models, four types of errors—correlation coefficient (R), T-Test, Analysis of Variance (ANOVA), and Taylor’s Diagram—have been used. The results of the study show successful application of Artificial Intelligence (AI) and empirical equations to capture the non-linear behavior of sediment concentration variables and indicate that, among all models, the ANFIS outperformed in simulating the total sediment load with a high R-value of 0.958. The performance of various models in simulating sediment concentration was assessed, with notable accuracy achieved by models AIM11 and AIM21. Moreover, the newly developed equation performed better (R = 0.92) compared to the Ackers and White formula (R = 0.88). In conclusion, the study provides valuable insights into sediment concentration dynamics in canals, highlighting the effectiveness of AI models and optimization techniques. It is suggested to incorporate other AI techniques and use multiple canals data in modeling for the future.

Sounding out horse mussel sediment thickness: an integrated data approach

Horse mussel beds are listed as a Priority Marine Feature (PMF) in Scotland for their influence in the creation of diverse benthic communities and provision of ecosystem services. In Scotland, horse mussel beds are also recognised for their importance in marine carbon sequestration. Unfortunately, there is a paucity of data on horse mussel bed carbon stocks and sediment thickness. There are also significant financial and logistical barriers with which to address these data gaps. This study investigates the robustness of Sub-Bottom Profiling (SBP) as a cost-effective method to quantify horse mussel sediment thickness across a landscape. Integrating SBP and Drop-Down Video (DDV) data, this study also details an integrated approach to investigate the links between horse mussel habitat condition and sediment thickness. With the addition of abiotic data, this study uses Structural Equation Modelling (SEM) to elucidate key relationships between abiotic factors, biotic variables, and sediment thickness. There is a significant positive correlation of horse mussel habitat condition and sediment thickness. Average horse mussel total sediment thickness, across all measures of habitat condition, was 1.37m. These findings substantially increase previous estimates of horse mussel sediment thickness, and potential value to climate change mitigation through blue carbon frameworks. This study highlights the importance of both abiotic and biotic factors on marine carbon sediment quantification.

Suspended Sediment Source and Transport Mechanisms in a Himalayan River

The process of estimating sediment load has been a daunting issue in hydraulics and the water resource field. Several methods exist for predicting the sediment load in a catchment or river, but the majority of these methods are empirical and depend on the specific location where they are used. Understanding the underlying mechanism of sediment generation and its transport in connection with precipitation, topography, and subsurface conditions to characterize its process is helpful for determining the sediment load in a river. For this purpose, we analyzed the daily suspended sediment data measured for 8 years at the headworks of the Kabeli A hydropower project in the Kabeli River, which originates from the Himalayan region. The analyses show that the suspended sediment concentration (SSC) varies in an orderly manner over time and asynchronously between seasons with respect to the river discharge. Clockwise hysteresis is observed in the yearly plots between the SSC and river discharge. The hysteresis becomes narrower when compared with the direct runoff obtained from a digital filtering algorithm and, even more so with the direct runoff from the hydrological model SWAT. The analysis shows that the sediment concentration is controlled not only by the total discharge in the river but also by the contribution of ground water to the river discharge, indicating that the total discharge alone cannot reflect the seasonal variation in SSC. It is inferred that the river is supply-limited and the hillslope is transport-limited with respect to sediment sources. The SWAT model suggests that the base flow contribution to the total river discharge is 78%. Here, we present a method for constructing the suspended sediment rating curve by comparing the direct runoff with the sediment concentration. The deduced sediment rating curve captures 84.51% of the total sediment load over the study period in the Kabeli River. This method may potentially be used in similar catchments with supply-limited rivers and transport-limited hillslopes.

GASTROPOD DIVERSITY AS A BIO-INDICATOR OF AQUATIC POLLUTION IN SIRONJONG GADANG ISLAND PESISIR SELATAN DISTRICT

This study aims to determine the diversity of gastropods and water conditions on Sironjong Gadang Island, Pesisir Selatan Regency. This research was conducted in August 2022 in the waters of Sironjong Gadang Island and the Marine Biology Laboratory and Marine Chemistry Laboratory of the Department of Marine Science, Universitas Riau. The method used in this research is the survey method, which is direct observation of the research area and sampling and measurement of water quality parameters in the field. The results of the study found gastropod species consisting of 4 (four) families, 4 (four) genera, and 8 (eight) species. The diversity value (H') was at a moderate level of diversity. The highest gastropod density was found at Station I, with a density value of 16.33 ind/m², and the lowest density was found at Station III, with a density value of 13.89 ind/m². The highest relative density was Monodonta labia species, with a relative density value of 27.6%, while the lowest relative density was Haustrum-scoring species, with a relative density value of 3.3%. Temperature 28-29˚C; salinity 25-27 ppt; pH 7.91-7.95; brightness 1.55-2.65 m. The sediment type at Station I was dominated by muddy gravel, Station II was dominated by sandy gravel, and Station III was defeated by sandy gravel with a total sediment organic matter content of 6.10-10.05%.

Controls on Sediment Transport From a Glacierized Catchment in the Swiss Alps Established Through Inverse Modeling of Geomorphic Processes

AbstractAs climate warms, hydrology and geomorphology in glacierized catchments are evolving, changing sediment export from these catchments, thus impacting downstream ecosystems and communities. Currently, much uncertainty persists regarding interactions among geomorphic processes that evacuate sediment from glacierized catchments. Here, we present a catchment‐scale numerical model of subglacial and proglacial sediment transport with debris meltout processes. We apply the model in a Monte Carlo framework to suspended sediment data collected over 2014–2020 from the Fieschertal catchment in the Swiss Alps, assessing possible combinations of geomorphic processes responsible for suspended sediment discharge. The ensemble of model outputs quantifies the interaction of different geomorphic processes, including the trade‐off between bedrock erosion and sediment previously stored in the catchment. Model runs suggest that, at some periods, up to 20% of the sediment leaving the glacier is deposited in the proglacial area relative to the catchment's total sediment discharge. This shows that the model captures the proglacial area change from sediment source to sediment sink in different hydrological and glaciological conditions. Furthermore, the findings highlight the impact of glacier retreat on the catchment's sediment dynamics, which both reduces the proglacial area's slope and introduces additional sediment to the proglacial area through debris meltout. The model outputs and the parameters quantify the interaction among geomorphic processes, yielding key insights into the drivers of sediment transport in alpine regions. The implications of these interactions are discussed in the context of interpreting processes responsible for controlling erosion rates from glacierized regions and modeling sediment transport in glacierized catchments.

Serra da Canastra National Park: Influence of forest fires on the RUSLE C factor and its impact on water erosion

The adverse impacts of soil degradation and nutrient loss resulting from water erosion are significant environmental concerns that have profound implications for both water quality and biodiversity. This study aims to evaluate the impact of forest fires on soil loss through water erosion in the Serra da Canastra National Park, in Minas Gerais state, Brazil. Using the Revised Universal Soil Loss Equation (RUSLE), which considers rainfall erosivity, soil erodibility, slope length and slope and vegetation cover, the C factor (vegetation cover) values were obtained from data from literature and methods based on the Normalized Differential Vegetation Index (NDVI). Validation was carried out using data on total sediment, water flow and daily runoff from the hydrosedimentological station and the InVEST software. The results highlight the significant impact of wildfires on soil loss through water erosion and indicate that areas recently affected by wildfires, especially on steep slopes and with more erodible soils, are subject to the highest rates of soil loss. Soil loss rates varied from 0.75 to 12.55 Mg ha-1 yr-1, in part due to the different ways of obtaining factor C. The research emphasizes the need to conserve vegetation cover to prevent soil erosion, particularly in regions impacted by forest fires. This study offers valuable insights that can contribute to enhancing the sustainable environmental management of the Serra da Canastra National Park.

Sediment and phosphorus transport during flood events in a Mediterranean temporary river

Flood events, whose number and intensity are predicted to increase in the Mediterranean region, are difficult to monitor. This causes the number of observations of suspended sediment and total phosphorus concentration (|SS| and |TP|, respectively) during their occurrence to be still scarce. Non-perennial or temporary water bodies, which react more promptly to rainfall events, represent ideal natural observatories. In this study, observations of streamflow, |SS| and |TP|, carried out during some flood events, in the Celone river basin, a temporary river located in south-eastern Italy, are presented. The research examined the correlations between flows, concentrations and loads of sediment and phosphorus and investigated factors that influence sediment and phosphorous dynamics in the river basin. The results show no relationship between the time of the year and the precipitation quantity of each event. The high coefficient of determination of the |SS|–|TP| correlations (R2 = 0.67 on average) proves the importance of soil erosive processes in the delivery of phosphorus to the river. More than 73% of the total suspended sediment load and 83% of total phosphorus load in the period 2010–2011 were transported during the 11 monitored events. In addition to the discharge, |SS| and |TP| also depend on numerous other factors related to land management, such as soil cover and fertilizations. The study, thanks to the improved understanding of the mechanisms governing sediment and phosphorus losses, represents a useful contribution for river basin authorities who have to draw up management plans aimed at preventing eutrophication phenomena and soil fertility reduction.

Assessment of lake-level variations to decipher geological controlling factors and depositional architecture of Lake Fuxian, Yunnan Plateau: preliminary insights from geophysical data

Lake Fuxian is one of the deepest tectonic plateau freshwater lakes in the southeastern Tibetan Plateau, China. However, questions such as how old the lake is, how deep the total sedimentary thickness sequences are, and what landscape of the lake basin settings and geological structures are unknown. Here, based on fifteen seismic reflection profiles, we applied seismic facies and seismic sequence stratigraphic analyses to interpret the lake sequences. The results of the seismic response reveal that the maximum thickness of the sedimentation is ca. 1238 m and lies toward the NNE region of the lake basin on the L10-2 survey line. Lake sediments can be categorized into five seismic sequences and six seismic horizons. The oldest clinoforms in the deepest sequence (Sq-5) show that the depositional center was shifted to ~ 19 km from the NNE region to the SSW modern location and was ~ 930 m lower than the current lake floor. Multiple and complex tectonic activities strongly impacted on the lake basin, and a series of normal faults created an overall crustal extensional regime, resulting in the formation of many horst and graben structures.

Temporal variation of braided intensity and morphodynamic changes in a regulated braided river using 2D modeling and satellite images

AbstractThe river morphology of a braided‐type river is rather complex. High sediment transport rates and frequently changing discharges are the cause of dynamic planform evolution. Over the past few decades, scientific attention has been directed toward understanding the coexistence of alternating bars and the consequent emergence of confluences and divergences, all of which interact intricately with the process of bank erosion. It is still rather challenging to estimate or predict the total sediment transport rate in this type of river, especially by considering various hydrologic data and climate effects. This study is focused on the reach of the Devoll River in Albania, located upstream of the Banja dam. Understanding the morphodynamics of this river reach holds significance due to the expanding delta upstream of the dam reservoir. The objectives of the two‐dimensional depth‐averaged approach of the present study are to investigate the temporal variation of braided intensity of Devoll River and the effect of using a discharge hydrograph from hydrologic data compared to the regulated one from the upstream dam on the morphodynamics and sediment transport of the river. After evaluating various parameters such as 11 different sediment transport functions, the best results were reached for a cell size of 5 × 5 m2, Manning roughness coefficient of 0.03, Meyer‐Peter and Müller's sediment function, Hayashi et al. (1980) hiding function, and Van Rijn bed roughness predictor in this study. In addition, the results of comparing satellite images and modeling the river from 2019 to 2023 show that the braided index decreased, and this can be due to the fact that the real scenario of the river has a regulated discharge compared to the non‐regulated discharge from hydrologic data, in the mentioned period.

Erosion processes and sediment source tracing on heterogeneous slopes in the red soil region of southern China

AbstractUnderstanding erosion, sediment sources and the spatial distribution along heterogeneous slopes is essential for soil and water conservation. In this study, soils derived from nodular limestone, mud‐like limestone and limestone breccia (abbreviated as SMTL, SMDL and SLBC, respectively) were utilized to establish artificial homogeneous and heterogeneous slopes. The homogeneous slopes MTL, MDL and LBC represent SMTL‐, SMDL‐ and SLBC‐filled‐ slopes, respectively. The heterogeneous slopes were abbreviated as MTL/MDL, MDL/LBC and LBC/MTL. Rare earth elements (REEs; lanthanide, cerium and ytterbium) were used to tag soils on the upper and lower slope sections to track sediment transport and deposition. The results showed that for homogeneous slopes, the LBC slope was the most severely eroded, followed by the MDL and MTL slopes. For heterogeneous slopes, the order of erosion was LBC/MTL > MTL/MDL > MDL/LBC. Upslope sections contributed a sizable portion of the total sediment yield, ranging from 51% to 79%. Over time, the difference in the sediment contribution between the upslope and downslope regions decreased and reached equilibrium. Runoff rates on heterogeneous slopes demonstrated an inverse function (R2 > 0.75) in contrast to a logarithmic distribution (R2 > 0.87) on homogeneous slopes. Heterogeneous slopes displayed minimal intersegment variation and the absence of a consistent ordering of the magnitude of hydraulic parameters. Conversely, the hydraulic parameters of homogeneous slopes were consistently ordered across the slope sections. For sediment transport, all slopes exhibited suspension‐dominated flow with percentages greater than 89%. However, the particle size distribution of the sediment of heterogeneous slopes exhibited greater diversity and complexity because of the coexistence of distinct soils. These findings underscore the importance of customized strategies for soil and water conservation in environments characterized by diverse soil parent materials.

Fine particle contents in sediment drive silica transport and deposition to the estuary in the turbid river basin

Changes in riverine sediment transport are an important part of land-sea geochemical cycling and further impact geochemical element fluxes in turbid rivers. However, as a vital nutrient element supporting primary productivity, silica mobilization from drainage in turbid rivers is overlooked. The turbid Yellow River has a strong ability to adsorb reactive silica, thereby exerting a substantial impact on the estuarine deposition of silica. Through an integration of monitoring databases, field sampling and historical hydrological data, we concluded that riverine fine particles control the exchangeable silica in the river and its estuary under soil erosion. Indoor simulation further revealed that the adsorbed content of exchangeable silica (ex-Si) in fine sediment constituted 35 % of total sediment matter. In addition, the transport of phosphorus and ex-Si was jointly regulated by fine sediment in global fluvial sediment transport, thereby exerting additional influence on the trophic structure of estuarine ecosystems. Against the backdrop of sediment budget deficit in the estuary, the heightened content of fine particles is depleting the silica storage from estuarine sediments.

Efek Perbedaan Jenis Rumput Laut Sebagai Agen Fitoremediasi Pada Sistem Budidaya Udang Windu (Penaeus monodon) Semi Intensif

The primary sources of organic waste in prawn ponds include feed waste from the farming process as well as ongoing metabolic activity, such as the production of urine and faeces. The increase in organic waste has an impact on reducing the water quality, one of the solutions is by implementing phytoremediation with seaweed. This research aimed to analyzed the growth and ability of seaweed Sargassum sp., Gracillaria sp., and Caulerpa sp. as phytoremediation agents to reduce organic matter in waters. This research was conducted for 68 days and used an experimental method with a completely randomized design (CRD) with 4 treatments and 3 replications. The treatment are A Sargassum sp., B Gracillaria sp., C Caulerpa sp. and D control. The results indicated that treatment C tended to decrease total organic matter (TOM) and sediment organic matter by 123.74 mg/l and 1.37%, respectively. The result also revealed that Caulerpa sp. the most effective seaweed to be used as phytoremediation organic materials in tiger shrimp farms compared to the two other seaweed species (i.e., Gracillaria sp. and Sargassum sp.). The growth of seaweed showed that there was a significant difference in specific growth of seaweed. The best specific growth rate value in treatment C was 1.37 ± 0.1%. The results of this study shown that Caulerpa sp. has more effective remediate organic matter and improve seaweed growth than Gracillaria sp. and Sargassum sp.

Sediment sorting and transport mechanism controlled by both soil properties and hydraulic parameters on hillslopes

Understanding the sediment sorting and transport processes is is crucial for enhancing the understanding of soil erosion mechanisms and improving soil erosion prediction. However, quantitative studies based on the coupling effects of both hydraulic parameters and soil properties are still lacking. In this study, five loessial soils with varying physicochemical properties were collected in the Loess Plateau of China, and simulated rainfall experiments were carried out in a metal box with a slope of 20 degrees under rainfall intensities of 1, 1.5, and 2 mm min−1. Runoff samples were collected to analyze the variation in erosion rates and effective particle size distribution of eroded sediments during the rainfall process. The results showed that the stream power was the optimal parameter to model the erosion rate, and a power function incorporating the clay content and stream power could well predict the erosion rate of different soils. The enrichment ratio indicated the enrichment of fine particles and depletion of coarse particles. And the sediment sorting degree increased with increasing soil clay content. The critical particle size for distinguishing different transport mechanisms varied among soils, with more than 55.46 % of the total sediment transported by suspension/saltation. A linear function and power function including the original soil particle size distribution and stream power were developed to quantify the sediment clay content and the relative contribution of different transport mechanisms. This study could be helpful to improve the soil erosion prediction model and provide basic guidelines for regional soil and water conservation.

Spatial distribution, source identification, ecological risk assessment, and air–seawater/seawater– Sediment exchange rates of polycyclic aromatic hydrocarbons in Pars special economic energy zone, Iran

Polycyclic aromatic hydrocarbons (PAHs) have been introduced as major pollutants released by the oil, gas, and petrochemical industries. Against this background, the present study examined the coastal air, seawater, and sediments in the Pars Special Economic Energy Zone (PSEEZ), Iran, in terms of pollution caused by such compounds. Considering the industrial facilities and residential areas in this region, the total suspended particulate (TSP), seawater, and sediments were sampled (n = 10) and then analyzed over the course of two seasons via gas chromatography-mass spectrometry (GC–MS). The total concentrations in the TSP, seawater, and sediments were found to be in the range of 346-739ngPAH/gTSP, ND-84.87 µg/L, and ND–306.7 ngg−1(dw), respectively. The positive correlation coefficients between sediment organic matter (OM) and concentrations did not show a significant relationship. Crude oil and its derivatives and biomass-coal combustion were identified as the main sources of pollution. Carcinogenic PAHs (CPAHs) were further detected at much higher concentrations near industrial facilities. Sediment qualityguidelines (SQGs) and risk quotients (RQs) showed that coastal seawater and sediments posed acceptable and moderate ecological risks. According to the fugacity diagrams, the seabed and seawater served as secondary sources of pollution. The total concentration and values obtained in earlier investigations were also comparable. Nonetheless, most maximum points could provide a point-form of the pollutant concentration. Therefore, preventive measures are required to ensure the protection of the environment.

HAEMATO-BIOCHEMCIAL STUDIES OF NANOPARTICLE-BASED VACCINE AGAINST R2B STRAIN OF NEW CASTLE DISEASE IN CHICKS

HAEMATO-BIOCHEMCIAL STUDIES OF NANOPARTICLE-BASED VACCINE AGAINST R2B STRAIN OF NEW CASTLE DISEASE IN CHICKS

Sediment transport modelling upstream of Al Kufa Barrage

Abstract This study estimated the amount of bed sediment load upstream of Kufa Barrage mainly depending on the hydrodynamic conditions, sediment concentration, and hydraulic parameters. Ten cross-sections approximately over 2 km in length in front of the barrage were selected. Velocities and suspended sediment concentrations at 0.2, 0.6, and 0.8 of the water depth at each section were recorded using an ADCP device. A depth-integrated sampling was utilized to examine the collected data from 6th January to 15th October 2022. It was noted that the effective depth-to-width computation methods and the Toffaleti sediment transport function with the Van Rijn fall velocity were the most compatible and appropriate approaches for determining the sediment transport potential in the selected reach. It was also noted that such techniques were better than the previous formulae to predict the total sediment load. The results revealed excellent agreement between the mean sediment discharge obtained using HEC-RAS 6.2, equal to 6.214 kg/s, and the mean sediment discharge obtained from the field measurements, equivalent to 7.142 kg/s.