Total Reflection X-ray Fluorescence Research Articles

Ultratrace determination of metal ions using graphene oxide/carbon nanotubes loaded cellulose membranes and total-reflection X-ray fluorescence spectrometry: A green chemistry approach

In this paper, the determination of ultratrace heavy metal ions was developed by combining a preconcentration method using graphene oxide/carbon nanotubes membranes (GO/CNTs) and total-reflection X-ray fluorescence spectrometry (TXRF). Due to the excellent adsorptive properties of the GO, the foregoing membranes are suitable for effective simultaneous sorption of Co(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II) from aqueous solutions. In this method, the aqueous solution is passed through the GO/CNTs membrane. The analytes are eluted from the GO and afterward transferred onto a siliconized quartz reflector for further TXRF analysis using W and Mo target X-ray tubes. The maximum recoveries for all the elements were obtained at pH 5; thus it was chosen for all further experiments. The face centered central composite design was performed to study the influence of the flow-rate and volume of the solution on the recovery of the determined metal ions. Recovery values higher than 96% for all studied metals allow performing efficient preconcentration with an enrichment factor of 133, achieving the limits of detection (LODs) in the range of 0.08–0.21 ng mL−1 for W target X-ray tube with a measurement time of 2000 s, and much lower LODs for Mo target X-ray tube: 0.001–0.002 ng mL−1 with the exception for Cd (0.11 ng mL−1) with a very short measurement time of 600 s. Certified reference materials of spring water and seawater were examined to verify the reliability of the method. The evaluated procedure does not require toxic reagents or organic solvents, thus minimizes the portion of the sample for TXRF measurement, and stands in good accordance with green analytical chemistry basic principles.

Comparative analysis of X-ray fluorescence methods for elemental composition determination of the archaeological ceramics from low sample quantity

Wavelength-dispersive X-ray fluorescence analysis (WDXRF) and total-reflection X-ray fluorescence (TXRF) analysis were applied to study the elemental composition of the Late Neolithic ancient ceramics collected at the Popovsky Lug burial site (Kachug, Upper Lena river, Russia). Semi-quantitative non-destructive analysis of ceramic pieces showed that measurements of the upper and lower sides of the ceramic are less informative than the measurement of its cut. Various sample preparation techniques for the low quantity of crushed ceramics such as fusion, pressing and preparation of suspensions were compared to preserve the material. Samples were prepared as 150 mg fused beads and 250 mg pressed pellets for WDXRF, and as suspensions of 20 mg sample based on the aqueous solution of the Triton X-100 surfactant for TXRF. Certified methods were used to validate the obtained contents of rock-forming oxides and inductively coupled plasma mass spectrometry was used to confirm the results of trace elements determination. Based on the carried-out studies, a combination of the wavelength-dispersive X-ray fluorescence analysis (glass) and total-reflection X-ray fluorescence analysis (suspension) methods was chosen to obtain the data on the elemental bulk composition of archaeological ceramics. The proposed combination allowed the quantitative determination of Na, Mg, Al, Si, P, K, Ca, Ti, Mn, Fe, V, Cr, Ni, Cu, Zn, Ga, Rb, Sr, Y, Zr, Pb, and Ba from the sample of crushed ceramics weighing only about 170 mg.

A round robin test for total reflection X-ray fluorescence analysis using preselected and well characterized samples

A TXRF round robin test using preselected micro- and nanoscaled samples has been performed and shows excellent results, demonstrating the strength and reliability of the TXRF method when decoupled from unfavorable sample preparations.

Total reflection X-ray fluorescence analysis with a glass substrate treated with a He atmospheric pressure plasma jet

A glass substrate treated with a He atmospheric pressure plasma jet gave a film-like residue from a small droplet of the red wine. This technique was effective in decreasing the matrix effect for TXRF analysis of low-Z elements.

Total reflection X-ray fluorescence analysis of aerosol particles with direct dissolution of the collection filter on a substrate

In this study, a novel method based on total reflection X-ray analysis was developed for determining the trace elements in aerosol particles.

Highly selective and sensitive determination of mercury ions by total-reflection X-ray fluorescence spectrometry

A fast and low-cost method for the highly selective determination of ultra-trace Hg(ii) ions at ppt level using total-reflection X-ray fluorescence spectrometry.

Methodology development and optimization for direct quantification of total selenium concentration in mine water by total-reflection X-ray fluorescence spectrometry

Methodology for direct quantification of total selenium (Se) concentration in mine water by total-reflection X-ray fluorescence (TXRF) spectrometry was developed and optimized. Inductively coupled plasma – mass spectrometry (ICP-MS), as a recognized standard test method, was used as a benchmark for results verification. Preliminary measurements with aqueous multi-element standard solutions showed that Se concentration can be accurately determined down to 10 ng/g by using a single-drop of solution (10 μL) and a measurement time of 600 s. Quantification of lower Se concentration below 10 ng/g was subsequently optimized, also with aqueous multi-element standard solutions. Improvement in detection limit was accomplished by increasing amount of sample deposition as well as increasing measurement time. TXRF analysis of SRM1640a, Trace Elements in Natural Water, was also performed for accuracy check. The developed methodology was applied to analyze five raw mine water samples (MW-1, MW-2, MW-3, MW-4 and MW-5) collected from anonymous mine site locations. TXRF analysis was performed on the as-received samples directly without filtration, dilution and digestion. Samples were prepared as single-drop specimens and analyzed using a measurement time of 600 s. Se and fifteen other elements were detected in varying degree in the as-received samples. Se concentrations quantified by TXRF were 256.5 ± 22.5, 88.4 ± 1.4 and 61.3 ± 2.8 ng/g for mine water samples MW-1, MW-2 and MW-3, respectively, compared to 255.3 ± 5.6, 87.3 ± 2.6 and 59.7 ± 3.5 ng/g by ICP-MS. No clear Se-Kα peak above background was observed for samples MW-4 and MW-5. Increasing amount of sample deposition by preparing triple-drop specimens and using a longer measurement time of 1800 s, allowed a Se-Kα peak to emerge above the background for MW-4, but not MW-5. Se concentration in MW-4 quantified by TXRF was 4.9 ± 0.5 ng/g, compared to 6.7 ± 0.7 ng/g by ICP-MS, which represents an agreement within three standard deviation values between the two techniques. For sample MW-5, even after using triple-drop specimens and increasing the measurement time to 1800 s, Se concentration could not be determined because a Se-Kα peak was not detected by TXRF, compared to the Se concentration of 0.83 ± 0.1 ng/g obtained by ICP-MS. Overall, our analysis results showed that the TXRF technique can be used for direct analysis of total Se concentration in raw mine water samples down to ng/g range, providing high-quality, accurate and repeatable analysis comparable to ICP-MS while requiring much simpler sample preparation.

Study of chromium, selenium and bromine concentrations in blood serum of patients with parenteral nutrition treatment using total reflection X-ray fluorescence analysis.

Total reflection X-ray fluorescence analysis (TXRF) was used to determine chromium, selenium and bromine concentrations in blood serum samples of 50 patients with parenteral nutrition treatment. The concentrations were measured two times, namely in the first day (I measurement) of the treatment and the seventh day (II measurement) after the chromium and selenium supplementation. For comparison purposes also serum samples of 50 patients without nutritional disorders, admitted to a planned surgical procedure to remove the gall bladder (cholecystectomy), were analyzed and treated as the control group. Descriptive statistics of measured concentrations of Cr, Se and Br both for the studied and control groups was determined. In order to check the effectiveness of Cr and Se supplementation, the results of the first and seventh day measurements for studied group were statistically compared with each other, with literature reference values and with the results of the control group (two-group comparison). These comparisons indicate the effectiveness of selenium supplementation in the applied treatment procedure. In the case of Cr and Br concentrations no statistically significant differences were observed. We conclude that monitoring of the concentration of the important trace elements in human serum should be standard procedure in parenteral nutrition treatment. In this monitoring the TXRF technique can be successfully used.

Total Reflection X-Ray Fluorescence Spectroscopy (TXRF) Method Validation: Determination of Heavy Metals in Dietary Supplements

Dietary supplements may contain heavy metals with the property of bioaccumulation in humans. The aim of this research was to validate and apply two analytical methods to determine Pb, As, Cr, and Hg in dietary supplements by Total Reflection X-ray Fluorescence Spectroscopy (TXRF). Methods validation was conducted through a multivariate analysis using a central composite design (CCD) and a desirability function. Critical values for each study variable were established. The TXRF_DS_1 method was proposed for Pb, As, and Cr determinations, while the TXRF_DS_2 was established for Hg analysis. The digestion method with an acid mixture (HNO3 + HCl + H2O2) was used to break down the organic material of dietary supplements. A solution of 10 μg L−1 Ga was used as an internal standard. Excellent analytical performance was obtained as LODs of 0.59, 0.41, 0.57, and 0.75 μg L−1 and LOQs of 1.95, 1.35, 1.90, and 2.50 μgL −1 for Pb, As, Cr, and Hg, respectively. Calibration curves showed a good linearity for all elements (R2>0.999). Excellent accuracy and precision in measurements (% RSD) was achieved. The real and spiked samples analysis demonstrated the applicability of the TXRF technique (percentage recovery 91–108%). Besides, two samples were analyzed in a comparison study between the TXRF_DS_1 method and the ICP-OES method. The results obtained showed good agreement between both techniques. The TXRF technique allows the analysis of toxic heavy metals in dietary supplements, which are marketed in a wide variety of presentations.

Extracting the local electronic states of Pt polycrystalline films surface under electrochemical conditions using polarization-dependent total reflection fluorescence x-ray absorption near edge structure spectroscopy

The local atomic information about the interface between the 30 nm-thick Pt polycrystalline films and the solution with and without perfluorosulfonic acid polymers (Nafion®) for the model cathode catalyst of fuel cell has been captured under electrochemical conditions using polarization-dependent total reflection fluorescence x-ray absorption near edge structure spectroscopy (PTRF–XANES). The results show that the formation of sub-monolayer-equivalent PtO or adsorbed hydrogen/oxygen species in the surface region can be successfully observed in the PTRF–XANES spectra when the thickness of the solution layer and the incidence angle are properly controlled. This capability enables us to examine the metal /(Nafion®/) solution interface structure through XANES together with other surface analysis methods, which will enhance comprehensive understanding of the nature of the interface of the fuel cell system.

Comparison of Elemental Anomalies Following Implantation of Different Cell Lines of Glioblastoma Multiforme in the Rat Brain: A Total Reflection X-ray Fluorescence Spectroscopy Study.

Glioblastoma multiforme (GBM) is a primary brain tumor with a very high degree of malignancy and is classified by WHO as a glioma IV. At present, the treatment of patients suffering from GBM is based on surgical resection of the tumor with maximal protection of surrounding tissues followed by radio- and pharmacological therapy using temozolomide as the most frequently recommended drug. This strategy, however, does not guarantee success and has devastating consequences. Testing of new substances or therapies having potential in the treatment of GBM as well as detection of their side effects cannot be done on humans. Animal models of the disease are usually used for these purposes, and one possibility is the implantation of human tumor cells into rodent brains. Such a solution was used in the present study the purpose of which was comparison of elemental anomalies appearing in the brain as a result of implantation of different glioblastoma cell lines. These were two commercially available cell lines (U87MG and T98G), as well as tumor cells taken directly from a patient diagnosed with GBM. Using total reflection X-ray fluorescence we determined the contents of P, S, K, Ca, Fe, Cu, Zn, and Se in implanted-left and intact-right brain hemispheres. The number of elemental anomalies registered for both hemispheres was positively correlated with the invasiveness of GBM cells and was the highest for animals subjected to U87MG cell implantation, which presented significant decrease of P, K, and Cu levels and an increase of Se concentration within the left hemisphere. The abnormality common for all three groups of animals subjected to glioma cell implantation was increased Fe level in the brain, which may result from higher blood supply or the presence of hemorrhaging regions. In the case of the intact hemisphere, elevated Fe concentration may also indicate higher neuronal activity caused by taking over some functions of the left hemisphere impaired as a result of tumor growth.

Lead (Pb) exposure assessment in dried blood spots using Total Reflection X-Ray Fluorescence (TXRF)

Lead (Pb) exposure is often determined through the analysis of whole blood though venipuncture poses ethical, economic, and logistical barriers. Dried Blood Spots (DBS) may help overcome such barriers though past studies measuring Pb in DBS have been challenged with quality control, small sample volumes, and other issues. Total Reflection X-Ray Fluorescence (TXRF) may help address some of these challenges but has yet to be used to measure Pb in DBS. As such, the aim of the current study was to develop, validate, and apply a method to analyze Pb in DBS samples using TXRF for use in human biomonitoring studies. First, we developed a novel method (tested a range of parameters), and then used blood reference materials to validate the method against performance criteria listed in ICH Q2A and Q2B and the European Bioanalysis Forum. Finally, we applied the method to two populations who exemplify divergent conditions (41 university members with relatively low Pb exposures sampled in a clinical environment; 40 electronic waste workers with relatively high Pb exposures sampled in a contaminated field setting). The limits of detection and quantification of the method were 0.28 and 0.69 μg/dL, respectively. The overall precision and accuracy of the method were 15% and 111%, respectively. The mean (±SD) DBS Pb levels by TXRF in the university members and e-waste workers were 0.78 (±0.46) and 3.78 (±3.01) μg/dL, respectively, and these were not different from Pb measures in venous whole blood using ICP-MS. Bland-Altman plot analyses indicated good agreement between DBS Pb measures by TXRF versus whole blood Pb measures by ICP-MS in both groups. By combining data from the two population groups, there was no significant constant bias (intercept of 0.02 μg/dL) or proportional bias (slope was −0.02) between the two measures, and the lower and upper LoA were −0.86 and 0.91 μg/dL, respectively, with a LoA range of 1.77 μg/dL. These results demonstrate that TXRF-based analysis of Pb content in DBS is a good alternative to the gold standard (i.e., ICP-MS analysis of whole blood), and helps overcome some of the challenges associated with current methods.

Characterization of archaeological ceramics from eastern Siberia by total-reflection X-ray fluorescence spectrometry and principal component analysis

The study of the composition of archaeological ceramics provides information used to assess possible transportation routes and cultural connections between ancient people living in different regions. Total-reflection X-ray fluorescence (TXRF) was applied for the analysis of ceramics as a promising method due to the rapidity, cost-efficiency, and capability to analyze a very small amount of a sample (<20 mg), which is important for the preservation of archaeological material. Two techniques of sample preparation for the TXRF analysis of ceramics have been considered. The analysis of suspensions was applied to obtain information on the bulk composition of ceramics. Acid leaching was used for the elemental analysis of the clay component of the ceramics, with the separation of non-soluble mineral phase. The proposed TXRF techniques have been successfully validated by the analysis of reference material and comparison with independent analytical methods. Reproducibility (interlaboratory precision) was evaluated for the proposed TXRF leaching method involving two different laboratories. The application of grazing incidence X-ray fluorescence (GI-XRF) showed homogeneous distribution of elements in the specimen and correspondence of the measurements to the conditions of total external reflection. TXRF method was applied to collect the first data on the composition of archaeological samples of ceramics from Popovsky Lug, eastern Siberia (Russia). The obtained data on the elemental composition were used to classify the samples by statistical methods of analysis, including the method of principal components and factor analysis. Three different compositional groups of ceramic have been separated and accepted as corresponding to archaeological interpretation.

Towards a calibration of laboratory setups for grazing incidence and total-reflection X-ray fluorescence analysis

Grazing-Incidence X-ray fluorescence (GIXRF) analysis, which is closely related to total-reflection XRF, is a very powerful technique for the in-depth analysis of many types of technologically relevant samples, e.g. nanoparticle depositions, shallow dopant profiles, thin layered samples or even well-ordered nanostructures. However, the GIXRF based determination of the depth-dependent information about the sample is usually based on a modeling of the experimental data. This requires profound knowledge of the geometrical parameters of the setup employed, especially the incident beam profile as well as the detector aperture parameters. Together they determine the incident angle dependent so-called effective solid angle of detection which must be known in order to model any experimental data set. In this work, we demonstrate how these instrumental parameters, which are typically not known with sufficient accuracy, can be determined using dedicated experiments with a well-known calibration sample. In addition, this paves the way for a full calibration of the setup, as also information about other parameters, e.g. the incident photon flux is gained. Here, we are using a commercially available instrument for this demonstration but the principle can also be applied for other GIXRF setups.

Combining Ion Chromatography and Total Reflection X-ray Fluorescence for Detection of Major, Minor and Trace Elements in Quartz-Hosted Fluid Inclusions

The crush-leach technique is a frequently used method to determine the bulk composition of fluid inclusions trapped in a range of geological samples. We present a modified crush-leach technique combining ion chromatography (IC) and total reflection X-ray fluorescence spectroscopy (TXRF) which allows to determine a range of major, minor and trace elements out of one leachate. To date, trace element detection by means of TXRF is barely used in geosciences, although it combines the advantages of low to very low detection limits (µg/L to ng/L range), small sample amount needed (µL-range) and a fast and inexpensive analytical procedure. Previously described problems of adsorption of polyvalent cations at sample surfaces have been overcome by using acidified water as a leachate. Instead, it has been demonstrated that, for example, the syringe filter type used for IC measurements influences contamination and/or adsorption for a number of elements. The proposed method combination was evaluated for accuracy, reproducibility and system blanks and subsequently applied to quartz samples from hydrothermal vein deposits of the Schwarzwald ore district, SW Germany.

Features of sample preparation techniques in the total-reflection X-ray fluorescence analysis of tea leaves

Tea is a popular drink around the world and contains essential minerals and trace elements for human health. In this study, the analytical capabilities of the total-reflection X-ray fluorescence method (TXRF) were considered for the analysis of tea. Different sample preparation techniques, e.g. suspension, open vessel acid digestion, and microwave acid digestion were examined. The influence of particle size was investigated in the analysis of the suspension of tea samples. Mass-absorption coefficients for the tea matrix and the critical surface density of the specimen were calculated. The data obtained explain the presence of absorption effects in the determination of P, S, Cl, and K in suspensions. The digestion procedure is chosen as an optimal sample preparation technique for the TXRF analysis of tea. Nineteen real tea samples were analyzed using TXRF. The advantages of TXRF have been presented through the comparison of results with the wavelength-dispersive X-ray fluorescence spectrometry method.

X-ray Fluorescence Techniques in Determining the Habitat Preferences of Species-Ulva pilifera (Ulvales, Chlorophyta) from Montenegro Case Study.

The paper presents four new sites where bright green Ulva thalli were found inhabiting freshwater (a river, a ditch, the Milet Canal) and marine (on the rocky shore of the Adriatic Sea) habitats in Montenegro. The aims of this study were to determine, for the first time, whether specimens of Ulva pilifera collected in Montenegro are phylogenetically and morphologically the same species as the one occurring in Europe. Using total reflection X-ray fluorescence (TXRF) and wavelength dispersive X-ray fluorescence (WDXRF) techniques it assessed the elemental composition of their thalli and its influence to colonise new habitats. Elements: Al, As, Ba, Br, Ca, Cl, Cr, Cu, Fe, Hf, I, K, Mg, Mn, Na, Ni, P, Pb, Rb, S, Si, Sr, Ti, V, and Zn were determined. The highest elemental concentrations were found for Ca = 16.3% (using WDXRF) and for Sr = 292 ppm (using TXRF) in the Ulva thalli. Ulva pilifera analysed from Montenegro, based on classical morphological methods and molecular techniques, are closely related to the same species from inland and coastal waters throughout Europe. The analysis of trace elements showed that the metal content in Ulva thalli is correlated with the trace elements in water and sediments. Ulva pilifera fits numerous features that make it one of the bioindicators of marine pollution, thanks to its worldwide distribution and capacity to accumulate trace elements.

Surface analysis of lanthanum strontium cobalt oxides under cathodic polarization at high temperature through operando total-reflection X-ray absorption and X-ray fluorescence spectroscopy

The surface chemistry of perovskite-type lanthanum transition metal oxides is an important parameter in high-temperature electrochemical devices such as solid oxide fuel cells (SOFCs). Strontium segregation on the surface of lanthanum strontium cobalt oxides (LSC) may lead to poor oxygen reduction kinetics. However, previous studies have not sufficiently addressed the oxide surface chemistry, including the oxidation change of LSC under cathodic polarization. In this study, operando total-reflection X-ray fluorescence absorption and X-ray fluorescence spectroscopy were performed to investigate cathodic polarization at high temperature (773 K) and at 1 atm pressure. Dense thin-film electrodes of La0.6Sr0.4CoO3 (LSC113) on Zr0.92Y0.08O1.96 electrolytes with a gadolinium-doped ceria interlayer were examined as model SOFC cathodes. This may be the first time that predominant surface reduction of cobalt is directly observed by using LSC113 under cathodic polarization. This phenomenon is related to strontium enrichment on the LSC surface. (La0.5Sr0.5)2CoO4 decoration on LSC113 enhanced the oxygen reduction kinetics compared with that of bare LSC113. This is due to the suppression of cobalt surface reduction and Sr enrichment in the LSC113 phase.

Lead Pb exposure assessment in dried blood spots using Total Reflection X-Ray Fluorescence TXRF

Whole blood remains the most used biomarker for lead (Pb) biomonitoring, however, blood sampling has several limitations, including its invasive nature. Dried Blood Spots (DBS) have been applied as an alternative to traditional methods for decades, but there are gaps that have prevented them to be adopted in biomonitoring programs, such as their small sample volume. There are microanalytical techniques that require a low volume (&lt;10 µL) to perform the analysis, such as Total Reflection X-Ray Fluorescence (TXRF), however, this approach has not been evaluated yet. This study aimed to validate and apply a method to assess Pb exposure using DBS samples and TXRF. First, we developed a method testing different parameters including digestion and extraction procedures, and the use of different internal standards. Next, we validated our method evaluating several validation parameters, and we compared our results with standardized guidelines. Finally, we applied our method with samples from two cohorts. The limits of detection and quantification of the method were 0.28 and 0.69 µg/dL, respectively. The overall precision and accuracy of the method were 14.88 % (9.92-19.14 %) and 111.14 % (97.03-129.70 %), respectively. The Bland-Altman plot indicated a good agreement between ICP-MS and TXRF, with a mean of differences of -0.02 µg/dL. These results demonstrate that TXRF is a good alternative to traditional methods for the analysis of Pb in DBS samples and it alleviates challenges such as the low volume of sample, analytical interferences, and sample throughput.

A road map to assess critical materials content in boron industrial wastes using sustainable micro-X-ray fluorescence and total reflection X-ray fluorescence instrumentation.

Turkey is the leading country in the world in terms of boron production and sale. Increasing boron production goes along with an increasing generation of boron wastes. The pollution of the soil and the air around the waste piles, as well as the occupation of several square kilometers of ground, are major environmental problems. It is, therefore, very important to make use of the wastes to both protect the environment and create revenue. This work presenteda road map for fast screening of boron waste for critical elements followed by determination of the elements using small footprint low power instrumentation. The sample preparation was kept to a minimum. A procedure that allowed an assessment of critical materials in industrial production waste with minimal consumption of hazardous acids, energy, and time was presented. The samples were first screened for valuable and hazardous elements by micro-X-ray fluorescence (XRF). Samples with considerable contents of Cs, Rb, and Aswere then prepared as slurries for the total reflection XRF (TXRF) measurement. To evaluate the TXRF procedure, a standard reference material was analyzed. As a result, Rb and Cs in concentrations up to 420 ± 70 and 1500 ± 200 mg/kg were detected in some of the waste forms. The time savings were in order of a factor of 3 when comparing the prescreening combined micro-XRF and TXRF approach to an all TXRFanalysis approach.