Titanium Dioxide Thin Films Research Articles

Zn-Modified TiO2 Thin-Films for Real-Time Formaldehyde Sensing at Room Temperature

Abstract This study explores the fabrication and application of zinc-modified titanium dioxide (Zn-TiO2) thin-films for real-time recognition of volatile organic compounds (VOCs), with a particular emphasis on formaldehyde (HCHO) sensing at room temperature. The Zn-TiO2 thin-films were produced using an economical spray-pyrolysis method. Structural, morphological, and optical characterizations confirmed the successful integration of zinc with varied Wt.% (0, 2, 4, and 6) into the TiO2 lattice. The real-time monitoring capabilities of the sensors were assessed against a range of VOCs, highlighting its specificity for formaldehyde detection amidst diverse environmental constituents. The fabricated thin film sensors with zinc dopant were optimized to enhance the sensor's performance. 4 Wt.% Zn-TiO2 demonstrated excellent sensitivity to formaldehyde vapor at ambient conditions, showcasing a rapid and selective response. The underlying sensing mechanism was explored, emphasizing the role of zinc doping in tailoring the material's surface properties and facilitating enhanced adsorption of formaldehyde molecules. The study underscores the potential of Zn-modified TiO2 thin films as a reliable and efficient platform for real-time VOC monitoring, with a specific focus on HCHO sensing at room-temperature. The sensor shows remarkable stability and repeatability, making it a promising candidate for continuous monitoring applications.

Enhanced ferroelectric photovoltaics by interfacial conductivity by stacking of bismuth ferrite and titanium dioxide thin films

Ferroelectric photovoltaic devices were assembled by direct stacking of bismuth ferrite (BFO) thin film with titanium dioxide (TiO2) thin film deposited on fluorine tin oxide (FTO) substrates. An enhanced short-current density of 4.06 mA/cm2 was received. The conductive atomic force microscopy (CAFM) confirms one order of magnitude increase on the collecting currents after coating of TiO2 on BFO thin film, majorly contributing from the interfaces among TiO2 and BFO particles. The ferroelectric photovoltaics generate an open-circuit voltage (VOC) of 1.66 V and a power conversion efficiency (PCE) of 4.18 %, benefiting from the enhanced conductivity of the thin film.

Exploration of physical properties of DC magnetron sputtered titania thin films and performance evaluation of Au/titania-based ultraviolet photodetectors

Exploration of physical properties of DC magnetron sputtered titania thin films and performance evaluation of Au/titania-based ultraviolet photodetectors

Investigating the influence of RF power on the surface morphological and optical properties of sputtered TiO2 thin films

Thin films of titanium dioxide (TiO2), with thicknesses ranging from 105 to 231 nm, were deposited on glass substrates using radio-frequency (RF) magnetron sputtering in an argon atmosphere at four distinct RF power levels: 40, 70, 100, and 130 W, with the deposition time kept constant. The crystalline structure, surface morphology and optical and semiconductor properties of the obtained films were analyzed using X-ray diffraction (XRD), Atomic Force Microscopy (AFM) and UV–visible transmittance spectroscopy. These analyses revealed that the crystallinity of the films improves with increasing RF power, corresponding to an increase in film thickness. Consequently, the samples transition from poorly crystalline or amorphous structure to a monocrystalline rutile phase with a (110) texture. However, at the highest RF power studied, this texture is partially disrupted by the formation of nanocrystals with different orientations. The surface roughness exhibited multifractal characteristics, with complexity systematically decreasing and surface stiffness reducing as RF power increased. Refractive indices and optical band gap energies were determined using the Swanepoel and Tauc plot methods, respectively. The films exhibited a notable increase in the refractive index and a decrease in the optical band gap, from 3.81 eV to 3.52 eV, as the RF power was increased. This underscores the influence of RF power on the optical and semiconductor properties of TiO2 films.

Characterization and Performance Analysis of TiO<sub>2</sub> Coated UHMWPE for Biomedical Applications

Ultra-high Molecular Weight Polyethylene (UHMWPE) is a highly versatile polymer known for its exceptional mechanical properties, however, its limited life as an implant material for Total Joint Replacement (TJR) necessitates surface modification to extend its lifespan. This study aims to enhance the surface properties of UHMWPE through application of ceramic coatings. Magnetron sputtering method was used to deposit thin film of white Titania (TiO2) on the material’s surface. To evaluate the surface characteristics, such as surface roughness, uniformity and structure, coated and uncoated samples were analyzed through Atomic Force Microscopy (AFM), Scanning Electron Microscopy (SEM) and X-ray Diffraction Analysis (XRD). The material performance in relation to biological context was investigated through Contact Angle measurement. A comparative analysis of coated and uncoated samples was then performed. The coated samples showed better wettability compared to uncoated sample. This fact highlights the hydrophilic nature of film. The results of the coated UHMWPE suggest that this surface modification technique could significantly extend the lifespan of UHMWPE implants in TJR, potentially addressing the current limitations associated with their longevity.

Low-temperature Deposited Highly Sensitive Integrated All-Solid Electrodes for Electrochemical pH Detection

This article describes the process of fabricating an integrated all-solid electrode (IASE) by integrating thin films of titanium dioxide (TiO<i>2</i>) and silver/silver chloride (Ag/AgCl) onto an indium tin oxide (ITO) substrate. The fabrication of a pH sensing electrode (SE) involved utilizing a spin-coated thin film composed of TiO<i>2</i>. Thermally produced thin films of Ag/AgCl were used to develop solid reference electrodes (RE). The present work examined the impact of the drying process on the pH sensitivity and linearity of the low-temperature deposited IASE. The drying procedure was carried out within a temperature range from room temperature to 100°C. The investigation involved the examination of crystallinity, surface morphology, and thin film composition through the utilization of field effect scanning electron microscopy (FESEM), X-ray diffraction (XRD), and energy-dispersive X-ray (EDX) methods. In addition, a comparison was made between the pH sensing performance of the IASE and a commercially available Ag/AgCl RE. The findings of this research demonstrate that the IASE sample, which underwent a drying process at a temperature of 100°C, exhibited remarkable sensitivity and linearity values of 66.7 mV/pH and 0.9827, separately, when compared to the commercially available RE.

Unification of insertion and supercapacitive storage concepts: Storage profiles in titania

Insertion storage in battery electrodes and supercapacitive storage are typically considered to be independent phenomena and thus are dealt with in separate scientific communities. Using tailored experiments on titanium oxide thin films of various thicknesses, we demonstrate the simultaneous occurrence of both processes. For the interpretation of the entire storage profile encompassing both contributions, the (free) energies of the charge carriers in the mixed conductor and the neighboring phase are the only materials parameters required. The experimental results enable no less than a unification of insertion and supercapacitive storage, the first being dominant for thick films, the latter for thin films or negligible electronic conductivity. Therefore, the size of the storage medium and the nature of the current collecting phases can be used to tune power density versus energy density.

Optimizing deposition parameters and characterizing TiO2 thin films for future memristor applications

Titanium dioxide (TiO2) thin films were deposited on glass substrates using Spray Pyrolysis technique, with variations in multiple deposition parameters. The molarity of the precursor was altered within a small range from 0.09 M–0.15 M. The deposition temperature was systematically adjusted from 200 °C to 400 °C while the ratio between precursor and chelating agent varied between 1:1,1:2 and 1:3. The thickness of TiO2 films were found to be in the range of 216 nm to 14.9 μm. Structural analysis conducted by XRD confirmed the formation of anatase TiO2 thin films. Optical studies using UV-Visible spectrophotometer determined the absorption and indirect bandgap ranging from 299 nm to 326 nm and 3.08 eV to 3.44 eV respectively. Electrical studies carried out evaluated the leakage currents and DC resistivity for all individual films with the input voltage applied from ± 0.5 V to ± 5V. Impedance studies were conducted by varying input voltages from 0.2V–3V for each film, so as to examine the resultant impedance, dielectric constant, dielectric loss, conductivity, admittance and modulus spectra. The obtained results were analysed to optimise the deposition parameters for designing future memristors with specific individual or combined characteristics, such as high ON/OFF, switching speed, endurance and retention.

Preparation and Photodegradation of TiO2 Thin Films on the Inner Wall of Quartz Tubes.

Titanium dioxide thin films on the inner wall of quartz tubes were prepared in situ by the sol-gel method. Meanwhile, copper and cerium were loaded onto the surface of the titanium dioxide thin films to enhance photocatalytic activity and broaden the range of light absorption. X-ray diffractometer, X-ray photoelectron spectroscopy, scanning electron microscopy, energy dispersive X-ray spectrum, N2 gas adsorption, UV diffuse reflectance spectroscopy, electron paramagnetic resonance, photoluminescene spectroscopy, and so on were used to characterize the structure, morphology, chemical composition, and optical properties of the prepared photocatalyst. Methylene blue (MB) was used as a simulated organic pollutant to study the photocatalytic performance of the photocatalyst, which was a translucent, structurally stable, and reusable high-efficiency photocatalytic catalyst. Under UV lamp irradiation, the MB photodegradation efficiency was 94.5%, which reached 91.2% after multiple cycles.

Preparation and optical characterization of 3D-TiO2 thin films with brilliant colors

In this paper, three-dimensional titanium dioxide (3D-TiO2) thin films with periodic structure were obtained by periodic pulse anodization of high-purity titanium wafers under specific alternating voltage (AV) using asymmetric sawtooth waveforms. The effect of voltage amplitude and electrolyte concentration on the structural color of the 3D-TiO2 thin films were investigated. It is shown that the nanotubes grown by asymmetric sawtooth wave at a specific AV have a “bamboo” shape, and the cycle length, as well as the inner and outer tube diameters of the nanotubes are closely related to the AV. The structural color of the samples was different at varying voltages and electrolyte concentrations for the same oxidation cycle time. The structural color of films grown under low voltage is analyzed to be related to the scattering and absorption of light on their surfaces. The thickness of the film grown under high voltage satisfies the conditions for light interference. The maximum reflected wavelength is red-shifted and then blue-shifted as the electrolyte concentration decreases. The study shows that the microstructure is the main influence on the color change of 3D-TiO2 thin films.

Unusual magnetism from lead adsorption on the surface of brookite titanium dioxide thin film

The adsorption of Lead (Pb) on brookite titanium dioxide thin films is determined using spin-polarized density functional theory. Band structures as well as density of states are shown. Magnetic irregularities are observed in thin layers that Pb atoms adsorb. The thin film has been identified to have a pivotal thickness of 1.6 nm. Beyond the essential thickness, Pb is unable to cause magnetic anomalies. The atypical magnetic properties stem from the quantum confinement phenomenon and the relaxation of the surface. The film’s long-range sequence presents complexity. The positioning of defects is dictated by the concentration of Pb volume rather than its concentration on the surface. The thin film exhibits a pivotal interaction range of 1.0 nm. A gap between two neighboring spins can lead to fluctuations in the magnetic configuration’s stability or instability, contingent on the Pb volume concentration. If not, the impact of long-range order is minimal, and the stability between magnetic and non-magnetic setups is nearly identical.

Features of the structure and resistive switching of titanium oxide films on Y-cut piezoelectric substrate of a LiNbO3 crystal

The difference in the structure of titanium oxide thin films deposited on fused silica substrates and the Y-cut of a lithium niobate crystal is demonstrated. In both cases, the film is amorphous; however, an insignificant amount of rutile crystallites is observed in the film formed on the Y-cut of the lithium niobate crystal. It is shown that the electrical characteristics of the films depend not only on the material of the substrate, but, in the case of the lithium niobate substrate, also on the direction of an electric field. This is caused by the deformation of the substrate due to the inverse piezoelectric effect.

Characterizations and optical discussions of thermally evaporated titanium dioxide thin films

Characterizations and optical discussions of thermally evaporated titanium dioxide thin films

Influence of Ag doping on structural, morphological, and optical characteristics of sol-gel spin-coated TiO2 thin films

Pure and Ag-doped Titanium dioxide (TiO2) thin films have been synthesized via the sol-gel spin coating method, and their structural, morphological, and optical properties have been investigated. X-ray diffraction analysis verifies that the polycrystalline anatase TiO2 phase is retained up to 2 % Ag doping. However, lattice expansion and grain refinement down to 25.345 nm are observed with increasing Ag content. Scanning electron microscopy (SEM) reveals the formation of large, isolated TiO2 aggregates separated by drying-induced cracks across the film surface. Optical studies show the undoped TiO2 films demonstrate excellent visible transparency (>75 % transmittance) that slightly decreases upon Ag doping, though it remains suitably high for device applications. Meanwhile, optical absorption and defect states improve with more Ag incorporation, narrowing the TiO2 bandgap from 3.83 eV (undoped) to 3.51 eV (2 % Ag-doping) due to the incorporation of Ag-induced electronic states just below the conduction band minimum. The capability to control optical and structural properties through Ag doping highlights the potential of these TiO2 films suitably tailored for photovoltaic devices or self-cleaning coatings.

Isolation of individual Er quantum emitters in anatase TiO2 on Si photonics

Defects and dopant atoms in solid state materials are a promising platform for realizing single photon sources and quantum memories, which are the basic building blocks of quantum repeaters needed for long distance quantum networks. In particular, trivalent erbium (Er3+) is of interest because it couples C-band telecom optical transitions with a spin-based memory platform. In order to produce quantum repeaters at the scale required for quantum networks it is imperative to integrate these necessary building blocks with mature and scalable semiconductor processes. In this work, we demonstrate the optical isolation of single Er3+ ions in CMOS-compatible titanium dioxide (TiO2) thin films monolithically integrated on a silicon-on-insulator photonics platform. Our results demonstrate an initial step toward the realization of a monolithically integrated and scalable quantum photonics package based on Er3+ doped thin films.

Nanoparticle/Cellulose-Based Surface Enhanced Raman Scattering Hybrid Sensors

Surface-Enhanced Raman Scattering (SERS) sensors are versatile biosensors for detecting very low concentrations of molecules. Their molecular and chemical sensitivity crucially depends on the tailoring of their nanostructure. These sensors rely on noble metal or oxide cluster layers, with their crystallinity and nanostructure carefully tuned to enable a maximum of plasmonic hot spots and enabling charge transfer. Typically, such sensors are in thin film geometry. In order to optimize their nanostructure and optical properties of the metal or oxide clusters, cellulose nanofibrils (CNFs) as template for nanoparticle-biopolymer hybrid materials are readily employed due to their high mechanical strength and ability to establish nanoporous, scalable thin films via spray deposition.[1] In order to characterize their nanostructure during synthesis of the hybrid nanoparticle-CNF material, grazing incidence X-ray scattering (GIXS) is ideally suited due to its ability to observe the nanostructural changes during farication and optimization of the sensor materials. The resulting nanostructure is then directly correlation to the sensor capability of the hybrid materials. As a first example, we use the catalytic properties of CNF during thermal decomposition of silver nitrate as precursor for fabrication of size-tuned silver clusters on CNF to tune their optical band-gap. The correlation between hot-spot size and silver nanoparticle size for optimizing the SERS sensitivity is elucidated using GIXS, showing for the first time the optimum hot spot size.[2] In order to facilitate an equal distribution of hot-spots, we make use of the three-dimensional nanoporous structure of the CNF thin films by adding shell-free silver nanoparticles in aqueous solution, again applying spray deposition.[3] The nanoporosity allows for reducing drastically agglomerations of silver nanoparticles, detrimental to hot-spots. At the same time, the spectral position of the plasmon resonance is tuned by the amount of CNF as structural matrix. As a final example we extend these results to novel semiconductor metal oxide nanomaterial (SMON)-based sensors.[4] Here, titanium oxide is deposited via atomic layer deposition (ALD) on the nanoporous CNF network, preserving its three-dimensional morphology. We optimize the nanostructure, crystallinity and rutile-to-anatase ratio in order to obtain superior sensitivity of the hybrid titania/CNF thin films as SMON SERS substrates. The improvement of SERS activity relies on the cooperative modulation of the CNF network and the crystalline states of the deposited titania. To summarize, we present new routes for SERS sensors based on plasmonic and charge transfer properties of hybrid materials by tailoring the hybrid nanostructure.[1] Brett, C. J.; Ohm, W.; Fricke, B.; Alexakis, A. E.; Laarmann, T.; Körstgens, V.; Müller-Buschbaum, P.; Söderberg, L. D.; Roth, S. V. Nanocellulose-Assisted Thermally Induced Growth of Silver Nanoparticles for Optical Applications. ACS Appl. Mater. Interfaces 2021, 13 (23), 27696–27704. https://doi.org/10.1021/acsami.1c07544.[2] Santoro, G.; Yu, S.; Schwartzkopf, M.; Zhang, P.; Koyiloth Vayalil, S.; Risch, J. F. H.; Rübhausen, M. A.; Hernández, M.; Domingo, C.; Roth, S. V. Silver Substrates for Surface Enhanced Raman Scattering: Correlation between Nanostructure and Raman Scattering Enhancement. Appl. Phys. Lett. 2014, 104 (24), 243107. https://doi.org/10.1063/1.4884423.[3] Chen, Q.; Brett, C. J.; Chumakov, A.; Gensch, M.; Schwartzkopf, M.; Körstgens, V.; Söderberg, L. D.; Plech, A.; Zhang, P.; Müller-Buschbaum, P.; Roth, S. V. Layer-by-Layer Spray-Coating of Cellulose Nanofibrils and Silver Nanoparticles for Hydrophilic Interfaces. ACS Appl. Nano Mater. 2021, 4 (1), 503–513. https://doi.org/10.1021/acsanm.0c02819.[4] Chen, Q.; Betker, M.; Harder, C.; Brett, C. J.; Schwartzkopf, M.; Ulrich, N. M.; Toimil‐Molares, M. E.; Trautmann, C.; Söderberg, L. D.; Weindl, C. L.; Körstgens, V.; Müller‐Buschbaum, P.; Ma, M.; Roth, S. V. Biopolymer‐Templated Deposition of Ordered and Polymorph Titanium Dioxide Thin Films for Improved Surface‐Enhanced Raman Scattering Sensitivity. Adv. Funct. Mater. 2022, 32 (6), 2108556. https://doi.org/10.1002/adfm.202108556.

Synthesis and Characterization of Cobalt-doped Titanium Dioxide Thin Films as Solar Cell Components using UV-SEM Analysis

Research has been carried out in the form of the synthesis and characterization of thin films of titanium dioxide with the addition of cobalt doping. The purpose of this research was to synthesize and characterize thin films related to optical properties, morphological shapes, and components of thin film compounds that are good for use as basic materials for the development of nanoparticle technology in the form of solar cells. The research was carried out in two stages, namely synthesis such as preparation of glass substrates, preparation of sol-gel solutions, deposition of solutions onto glass substrates, and heating of TiO2:Co thin film samples. The next stage is the thin film characterization test, where the optical properties of the thin film, such as absorbance, transmittance, gap energy, and activation energy, are measured using a UV-vis spectrophotometer, while morphological data and components of the thin layer compounds are measured using a Scanning Electron Microscope-Energy Dispersive X-rays (SEM-EDX). Based on data analysis and discussion, it was found that the optical properties, such as the transmittance value of the thin film, experienced the lowest point at a wavelength of 250–280 nm with a maximum percentage value of 62.14 to 78.85%. The greater the doping concentration, the lower the transmittance value. This condition is inversely proportional to the absorbance value of the maximum TiO2:Co thin film, which is in the region with a wavelength of 280–300 nm and a value of 5.70–6.31. The greater the doping concentration, the greater the absorbance value. The energy bandgap values of TiO2:Co thin films for doping concentrations (0, 5, 10, 15, 20)% were 3.44; 3.39; 3.38; 3.32; 3.22 eV for the direct energy bandgap and 3.86; 3.85; 3.84; 3.85; 3.82 eV for the indirect energy gap. The activation energy of the TiO2:Co thin film decreased from 2.86 to 2.26 eV. As for the morphological data of the TiO2:Co thin film, it was found that the greater the concentration of doping, the layer was deposited evenly, finely, and homogeneously. Regarding the data on the components of the thin layer compounds, it was found that the percentage of TiO2 content was in the range of 64.48–95.94%, while for Co, it was in the range of 0.00–19.21%.

Interfacial studies of Cu2O/TiO2 junction deposited at different electropotentials

Based on the simplistic two-step preparation method, a Cu2O/TiO2 junction was synthesized by electrodepositing a Cuprous Oxide layer on Titanium Oxide thin films at different deposition potentials. The thin films and junction were characterized for their structural, morphological, optical, and electrical properties using X-ray diffraction, Scanning Electron Microscopy, UV–visible spectroscopy, and Electrochemical Impedance Spectroscopy. The XRD analysis of the Cu2O/TiO2 junction indicated no sharp diffraction peaks of TiO2, only Cu2O peaks were observed. The Scanning Electron Microscopy also demonstrated that the Cuprous Oxide thin films possessed three-sided pyramidal structures on their surface. The band gaps of Cu2O and TiO2 thin films were calculated as 2.2 eV and 3.3 eV respectively by using Tauc’s plots. Electrochemical impedance spectroscopy revealed reduced interfacial charge transfer resistance and a boost in charge carrier generation in fabricated junctions (grown at −0.6 V). The flat band potentials and carrier concentrations of the fabricated thin films and their junction were calculated using Mott-Schottky analysis. Meanwhile, charge transfer resistance, solution resistance, constant phase element, and other circuit parameters of the electrochemical cell were studied using Nyquist plots.

Conformal TiO2 Aerogel-Like Films by Plasma Deposition: from Omniphobic Antireflective Coatings to Perovskite Solar Cell Photoelectrodes.

The ability to control the porosity of thin oxide films is a key factor determining their properties. Despite the abundance of dry processes for synthesizing oxide porous layers, a high porosity range is typically achieved by spin-coating-based wet chemical methods. Besides, special techniques such as supercritical drying are required to replace the pore liquid with air while maintaining the porous network. In this study, we propose a new method for the fabrication of ultraporous titanium dioxide thin films at room or mild temperatures (T ≤ 120 °C) by a sequential process involving plasma deposition and etching. These films are conformal to the substrate topography even for high-aspect-ratio substrates and show percolated porosity values above 85% that are comparable to those of advanced aerogels. The films deposited at room temperature are amorphous. However, they become partly crystalline at slightly higher temperatures, presenting a distribution of anatase clusters embedded in the sponge-like open porous structure. Surprisingly, the porous structure remains after annealing the films at 450 °C in air, which increases the fraction of embedded anatase nanocrystals. The films are antireflective, omniphobic, and photoactive, becoming superhydrophilic when subjected to ultraviolet light irradiation. The supported, percolated, and nanoporous structure can be used as an electron-conducting electrode in perovskite solar cells. The properties of the cells depend on the aerogel-like film thickness, which reaches efficiencies close to those of commercial mesoporous anatase electrodes. This generic solvent-free synthesis is scalable and applicable to ultrahigh porous conformal oxides of different compositions, with potential applications in photonics, optoelectronics, energy storage, and controlled wetting.

Understanding the effect of number of layers on the optical and wetting properties of titania thin films fabricated by sol-gel spin coating technique

Understanding the effect of number of layers on the optical and wetting properties of titania thin films fabricated by sol-gel spin coating technique