Nano Titanium Research Articles

Differential toxic effects of nano-titanium dioxide on clams (Meretrix meretrix) with various individuality

Nano-TiO2 is inevitably released into aquatic environment with increasing of nanotechnology industries. Study pointed that different individuality showed divergent behavioral and physiological response when facing environmental stress. However, the effects of nano-TiO2 on tolerance of bivalves with different individualities remain unknown. In the study, clams were divided into two types of individuality - proactive and reactive by post-stress recovery method. It turned out that proactive individuals had quicker shell opening level, stronger burrowing behavior, faster feeding recovery, higher standard metabolic rate and more rapid ammonia excretion ability than reactive individuals after exposed to air. Then, the survival rate, hemocytes response and oxidase activity of classified clams were evaluated after nano-TiO2 exposure. Results showed that after 30 d exposure, proactive individuals accelerated burrowing behavior with higher survival rate. Moreover, proactive clams had better adaptability and less hemocytes response and oxidative damage than reactive clams. The study highlights the individualities of marine shell fish determine individual capacity to adapt to environmental changes, play important roles in aquaculture and coastal ecosystem health.

Effects of Nano-Titanium Dioxide on the Horizontal Transfer of Antibiotic Resistance Genes in Microplastic Biofilms

Emerging pollutants such as microplastics in water environments readily accumulate microorganisms on their surfaces, forming biofilms and concentrating antibiotic-resistant bacteria (ARB) and antibiotic resistance genes (ARGs). Consequently, microplastic biofilms have attracted the attention of researchers. Horizontal gene transfer (HGT) of ARGs is one of the primary ways that bacteria acquire antibiotic resistance. Most studies focus on the effects of nanomaterials on suspended bacteria, but microplastic biofilms as hotspots for horizontal gene transfer also warrant significant investigation. This study primarily explored and compared the effects of nano-titanium dioxide on the conjugation transfer frequency of ARGs in suspended bacteria and microplastic biofilms. Nano-titanium dioxide could promote ARG conjugation in both suspended bacteria and microplastic biofilms, with a greater effect on the former. The mechanism involved nano-titanium dioxide promoting the production of reactive oxygen species (ROS) in suspended and biofilm bacteria, increasing the synthesis of outer membrane proteins, enhancing the cell membrane permeability, and elevating the expression levels of conjugation-related genes, thereby facilitating the conjugation transfer of ARGs. Biofilm bacteria, being heavily encased and protected by extracellular polymeric substances (EPS), exhibit greater resistance to external environmental pressure, resulting in the weaker impact of nano-titanium dioxide on biofilm bacteria compared to suspended bacteria. This study reveals the risk of ARG conjugation transfer within microplastic biofilms induced by nanomaterials, providing valuable insights into the risks of microplastic and antibiotic resistance dissemination in water environments.

INVESTIGATION OF THE EFFECTS OF THE ADDITION OF TITANIUM DIOXIDE (TiO2) NANOPARTICLE FUEL ADDITIVE IN COTTON BIODIESEL ON ENGINE PERFORMANCE

The importance of renewable fuels as an alternative to fossil fuels is increasing due to environmental problems such as the decrease in the reserves of fossil fuels, their presence in certain regions, air pollution and global warming. Two important parameters of biodiesel fuel, which is one of these fuel types, such as high viscosity and density, negatively affect its use. One of the ways to overcome this negative situation is to improve the fuel properties by adding nano fuel additives into biodiesel. In this study, titanium dioxide nano fuel additive was added to biodiesel obtained from cottonseed oil at the rates of 50 ppm and 75 ppm. Specific fuel consumption, brake thermal efficiency and cylinder pressure values, which are the basic performance parameters of the fuel mixtures, were determined in a single cylinder engine at 1800 rpm at 4 different engine loads. According to C100 fuel SFC decreased by 5.03% and 6.29% at 10 Nm load, respectively in CTi-50 and CTi-75 fuels. This improvement rate was 8.73% and 12.58% at 40 Nm load. BTE increased by 8.97% and 13.17% with NPs additives. Thanks to the thermophysical properties of the titanium dioxide fuel additive, the combustion reaction has improved and cylinder pressure increased. It was determined in the study that it positively affected the engine performance and fuel economy.

Microstructural analysis and densification of ordinary Portland cement mortars incorporated with minimal nano-TiO2: intermixing and surface coating on both fresh and hardened surfaces

The present study investigated the microstructural properties of ordinary Portland cement (OPC)-modified with minimum dosage of nano TiO2 on fresh and hardened cement mortar surfaces and intermixed samples. X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX) were used to analyze the morphology and hydration products of the OPC specimens doped with nanotitanium (NT).Additionally, XRD coupled with Rietveld refinement was employed to quantify the crystal phases and refine the crystal structure model through the comparison of the calculated diffraction pattern to the measured pattern. Subsequently, crystallographic analysis was conducted to evaluate the crystallographic structure and to confirm the existence of specific atoms and bonds within the crystal structure altered with NT. The findings revealed that the addition of minimal NT resulted in a more compact and denser microstructure, characterized by increased formation of calcium silicate hydrate (CSH) gel and a reduction in calcium hydroxide (CH) crystals.This led to a reduction in the porosity of the hardened coating surface, with similar improvements observed for the fresh coating and intermixed samples compared to those of the control mortar. A decrease in the lattice parameters, accompanied by an increase in the number of atoms, bonds and polyhedra in the crystal structure, led to alterations in the interatomic spacing and contributed to the densification of the cementitious matrix.The findings also showed that NT integration led to a more compact structure with shorter bond distances and smaller polyhedral volumes for the Ti samples than for the control sample. Moreover, compared with the freshly cast and hardened coating samples, the NT-intermixed samples exhibited the shortest Ti–O bond distances and the smallest polyhedral volume. Overall, the analysis presented in this study significantly contributes to the development of novel and environmentally friendly photocatalytic cementitious materials at minimal dosages.

Steady state chloride diffusivity in mortar containing nano titanium dioxide using response surface methodology

Steady state chloride diffusivity in mortar containing nano titanium dioxide using response surface methodology

REVIEW: AN EXPERIMENTAL STUDY ON EFFECT OF NANO MATERIALS ON STRENGTH OF CONCRETE AND PLANE STRESS ANALYSIS USING ANSYS SOFTWARE

These days, making efficient and cost-effective use of resources has taken precedence. The main ingredient in concrete, cement has been under criticism in recent years for the quantity of CO2 released during production. Although cement has better mechanical properties, it hasn't been able to live up to the expectations in terms of durability. Owing to cement's shortcomings, scientists started looking into additives that would enhance concrete's qualities while also making it stronger and lighter. Fly ash, silica fume, and other micro particles were added to cementitious materials to improve their compactness, strength, and durability. These additives were also selected because they are eco-friendly by products of industrial waste that may be handled ethically. Fly ash has significant disadvantages because it is not good for initial strength increase and setting time. Because silica fume affects cementitious material performance, researchers have recently become interested in combining it with ceramic waste and rice husk ash. A more effective way to utilize rice husk ash, a by-product of rice cultivation, would be to replace 10% to 15% of cement. Studies have shown improvements in the durability performance of recycled ceramic waste concrete and rice husk ash concrete. There are issues since the RHA production process is quite time-consuming. With the discovery of nano-particles (NP) smaller than 100 nm, researchers have advanced the field of nanotechnology to new levels. The mechanical properties of many materials, including polymers and cementitious materials, can be enhanced by NP. NP is also helpful in the fields of food, engineering, and medicine. This led researchers to investigate the effects of nano-silica (NS) on concrete in further detail. Nano materials can improve the compressive strength and ductility of concrete. In this project an effort will be made to increase the compressive strength of concrete using Nano materials and waste product like GGBS. Also plane stress analysis of concrete cubes and cylinders is to be done using Ansys Software to find deformation, principal stresses and shear stresses. Keywords: Nano –Silica, Nano Titanium dioxide, Ansys, GGBS, Compressive strength

Nano titanium dioxide alleviates the toxic effects of tris (2-chloropropyl) phosphate on the digestive gland and hemolymph of thick-shell mussel Mytilus coruscus

In the marine environment, nanoparticles play a role in adsorbing and catalytically degrading organic pollutants, thereby mitigating their toxic effects on aquatic organisms. This study aimed to investigate the impact of nano titanium dioxide (nTiO2) and tris (2-chloropropyl) phosphate (TCPP) on the hemolymph and digestive function of the thick-shell mussel Mytilus coruscus. Mussels were divided into a control group, a group exposed to TCPP alone, a group exposed to a combination of TCPP and 0.5 mg/L nTiO2, and a group exposed to a combination of TCPP and 1 mg/L nTiO2. After 14 days of exposure, oxidative stress responses, including superoxide dismutase (SOD) activity and malondialdehyde (MDA) content, immune defense responses, including acid phosphatase (ACP) and alkaline phosphatase (AKP) activities, and gene expression, including HSP70 expression, were measured in the hemolymph and digestive glands of the mussels. Compared to the control group, mussels solely exposed to 100 μg/L TCPP exhibited a significant reduction in SOD activity in the hemolymph. When TCPP was co-exposed with 0.5 mg/L nTiO2, there were significant increases in MDA content and AKP activity in both the digestive gland and hemolymph compared to the control group. Upon co-exposure of TCPP with 1 mg/L nTiO2, MDA content and AKP activity in the digestive gland significantly decreased, while SOD, ACP, and AKP activity in the hemolymph significantly increased and MDA content significantly decreased, returning to the control group levels. Furthermore, in the combined exposure, HSP70 gene expression significantly decreased as the nTiO2 concentration increased from 0.5 mg/L to 1 mg/L. In summary, TCPP impacted the hemolymph and digestive function of mussels, whereas a concentration of 1 mg/L nTiO2 effectively alleviated the toxic effects of TCPP. This study is crucial for assessing the ecological risks of nanoparticles and emerging organic pollutants in marine environments, and provides new insights into the interaction between nTiO2 and TCPP, as well as the influence of nTiO2 concentration on mitigating TCPP toxicity.

Uniaxial compression behavior of glass fabric/epoxy composites sprayed with nano titanium dioxide

ABSTRACT In this study, we have tried to study the compression behaviour of composites by a different technique of spraying nano – TiO2 on glass fibre fabrics with vinyl resin as binder and epoxy resin as matrix. It was found that the air spraying method was effective in loading the nanoparticles onto the fabrics and improving their wetting properties with the resins. The experimental results showed that the compressive strength of the modified specimens was lower than that of the untreated ones, while their compressive strength was increased. On this basis, the fracture process of the material was observed using microscopy, and electron microscopy observations revealed that the degree of interfacial bonding between the material and the substrate was improved, while the bond strength demonstrated the strong toughening effect of nano – TiO2 on the substrate. Electron microscopy tests also showed that the composites modified by nano- TiO2 showed significant improvement in matrix fracture, fibre breakage and delamination. This study provides a theoretical basis for the study of the mechanical properties of composite materials used as supports under uniaxial compression.

Effect of titania nano composite on structural and optical properties of Ho3+ doped silica glasses for green laser applications

Effect of titania nano composite on structural and optical properties of Ho3+ doped silica glasses for green laser applications

Enhancing dynamic viscoelastic performance of flax fiber/fly ash hollow cenosphere‐reinforced composites coated by in situ fabrication of ultrasonically synthesized nanotitanium dioxide

AbstractThis study demonstrates a novel, single‐step, and low‐energy ultrasonic approach to fabricate lightweight, high‐performance flax fiber‐reinforced composites enhanced by nanotitanium dioxide coating and fly ash hollow cenospheres. This innovative approach leads to a remarkable 23% weight reduction compared with conventional composites, making it ideal for the applications demanding both lightweight and superior mechanical properties. Through dynamic mechanical testing, it is found that the composites' viscoelastic behavior, including storage modulus and damping factor, is significantly influenced by both frequency and temperature. By applying time–temperature superposition principles, the composite's dynamic properties are comprehensively characterized across a wider frequency range. A modified fractional calculus Huet–Sayegh model accurately captures the observed viscoelastic behavior. The combined effect of nanotitanium dioxide coating, which strengthens the fiber–matrix interface, and the inclusion of rigid fly ash hollow cenospheres results in significant improvements in both storage modulus (10% increase at room temperature) and peak loss factor (80% increase) compared with uncoated flax fiber‐reinforced composites. The nanocoating and cenospheres' rigid shells contribute to enhanced stiffness, while the cenospheres' hollow structure provides efficient energy dissipation mechanisms, leading to an improved damping performance. This ultrasonic approach offers a promising and sustainable method for synthesizing natural fiber nanocomposites with superior viscoelastic properties.

Probabilistic material flow analysis of released nano titanium dioxide in Mexico

Engineered Nanomaterials (ENMs) or products containing ENMs, known as nano-enabled products are commercialized globally by a large number of companies. Concern about the potential risks and negative impacts of releasing ENMs into the environment is under investigation. For this reason, methodologies to estimate the probable mass concentrations of ENMs released in different regions of the world have been developed. As a first attempt to estimate the probable mass flows of nanosized titanium dioxide (nano-TiO2) released in Mexico, we developed a Probabilistic Material Flow Analysis (PMFA) for 2015.The model describes probabilistic mass flows of released nano-TiO2 during the life cycle of sunscreens, coatings, ceramic, and other nano-enabled products, including the flows through the solid waste and wastewater management systems, as well as the transfer of nano-TiO2 to three environmental compartments (atmosphere, topsoil, and surface water). The PMFA incorporates the uncertainty related to the input data. We observed that the most significant nano-TiO2 flows occur to the surface water, landfill, and soil compartments, targeted as the main “hot-spots”, where living organisms could be more exposed to this material. Further improvements in the model are needed due to some data gaps at some life cycle stages, for instance, solid waste management and reused wastewater manipulation for irrigation purposes. Finally, the model developed in this study can be adjusted to assess other ENM releases and can be beneficial for further investigation in fate modeling and environmental risk assessment.

Effect on concrete strength and durability with partial replacement of cement by Nano-titanium dioxide (nano-TiO2) and ground granulated blast furnace slag (GGBS): A Review Summary

Effect on concrete strength and durability with partial replacement of cement by Nano-titanium dioxide (nano-TiO2) and ground granulated blast furnace slag (GGBS): A Review Summary

Magnesium‐based nanocomposites developed through multi‐pass friction stir processing and strengthening mechanisms exploration

AbstractIn the current experimental work, using secondary phase hard nano titanium carbide (TiC) particles as reinforcement, two different magnesium metal matrices i. e., AZ31B/TiC and AZ61 A/TiC composite materials were synthesized by friction stir processing. Using the traditional testing approach for the developed materials, the simultaneous gain in metallurgical, mechanical, electrical, and tribological characteristics compared to the base substrate was examined. The microstructure study results for AZ31B/TiC and AZ61 A/TiC composites showed a uniform distribution of reinforced particles as well as an evolution in grain size, from 82 μm to 4.2 μm and from 74 μm to 3.7 μm, respectively, which consequently contribute in a significant gain in the microhardness of both composites i. e., around 2.2 times and 2.67 times respectively, greater than the base metal. When compared to monolithic alloys, the synthesized AZ31B/TiC and AZ61 A/TiC composites showed improvements in the areas of tensile strength, compressive strength, and coefficient of friction up to 1.81 times, and 1.64 times, 1.74 times and 1.58 times, and 57.92 % and 58.47 %, respectively. Furthermore, these improvements in characteristics also increase the final strengthening of the nanocomposite and reduce electrical conductivity.

Effective impact of nano-plastic-waste incorporated with nanotitina on the physical, mechanical and microstructural properties of white cement pastes composites for progressing towards sustainability

Plastic waste (PW) has received a lot of attention as a possible additional material for industrial and environmental applications, particularly cement and/or concrete production for a more environmentally and economically sound use of raw materials and energy sources. PW has been investigated as an inert and/or active hydraulic filler for cement and/or concrete by numerous scientists. Plastic garbage is cheap, abundant, and takes long period of time to degrade in the eco-system (soil and water). The main goal of the ongoing research is to offer safety and efficacy by partially substituting nano-plastic waste (NPW), incorporated with nano-titania (NT), for the composition of white cement (WC). Blends are built up by substitution of WC with different ratios of NPW incorporated with fixed ratios of nano-titania (1.0 wt.%). Workability, physical, mechanical and microstructural properties have gone through laboratory and instrumental analysis. The results showed improvement in the compressive strength, density and microstructure due to the effective impact of fillers. Consequently, a decrease in total porosity, whiteness reflection (Ry) and early-rapid expansion. Eventually, the outcomes may reduce the pandemic strength, especially in the external environment, and other epidemics.

Synthesis and utilization of titanium dioxide nano particle (TiO2NPs) for photocatalytic degradation of organics

A green technique that emerged as a promise in the degradation of numerous organic contaminants is photocatalysis. The aim of this study concerns photocatalytic degradation of organic using titanium dioxide nano particles (TiO2 NPs) which syntheses from ilmenite by different leaching methods using different ingredients such as HCl, HNO3 and Aqua Regia. The affecting factors such as rate of addition, reaction time, ilmenite grain size, acid to ilmenite ratio and reaction temperature were conducted. Comprehensive physicochemical characterization of Ilmenite and TiO2 NPs were conducted using different analytical techniques such as XRD, XRF, SEM, TEM and FTIR. Photocatalytic degradation of organics is confirmed by studies of affecting factors on the effectiveness of TiO2 NPs such as dose, agitation forces, light intensity, initial concentration, pH, time, and temperature. The removal percentages of TSS, COD, BOD and TN of organics were explored. From the results the maximum removal percentage of TSS were 97.3 and 96.9% before and after secondary treatment conducted using ferric chloride (FC). The maximum removal percentage of TKN, BOD, and COD before secondary treatment were conducted using mixture of TiO2 NPs, FC, and chitosan, which reached 44.2, 44 and 46.3%, respectively. The maximum removal percentage of TKN, BOD, and COD after secondary treatment were conducted using mixture of TiO2 NPs, FC, and chitosan, which reached 94.9, 99.7 and 99.6%, respectively. Overall, the results derived from this investigation suggest that the TiO2 NPs/UV holds significant advanced treatment of sewage water, making it a viable choice for water reuse applications.

Flexocatalysis of nanoscale titanium dioxide

Piezocatalysis emerges as a distinctive approach for producing free radicals to drive catalysis. However, the piezoelectric effect exclusively manifests in non-centrosymmetric materials, which largely constraints the use of materials with centrosymmetry. To address this challenge, the concept of flexocatalysis is explored to bypass the structural constraints of materials by harnessing strain-gradient-induced polarization, taking advantage of universality of flexoelectricity. As an exemplar of flexocatalysis, centrosymmetric rutile titanium dioxide (TiO2) nano particles are selected due to its high permittivity, non-toxicity, biocompatibility, and wide-ranging utility. The effectiveness of flexocatalysis in generating free radicals (·H, and ·OH) is validated through hydrogen generation (∼2380 μmolg−1h−1 in pure water) and Rhodamine B dye degradation. Additionally, the size effect on flexoelectricity is examined both experimentally and theoretically, revealing that materials at nanoscale exhibit greatly enhanced flexoelectricity that can rival the traditional piezoelectricity. This work endows TiO2 with novel capabilities and broadens material’s selection in mechanochemistry applications.

Titanium Dioxide and Calcium Sulfate Whiskers Are Used for the Preparation of High Performance Polypropylene and Reduce White Pollution.

The anti-aging agent TiO2-polyacrylonitrile (PAN) and the mechanical strengthening agent CSW-PAN were prepared by radical polymerization using rutile nano-titanium dioxide (TiO2) and anhydrous calcium sulfate whisker (CSW) as raw materials. The structures of TiO2-PAN and CSW-PAN were characterized using Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). Simultaneously, the mechanical properties, aging properties, and thermal stability of TiO2-PAN/CSW-PAN/polypropylene (PP) composites were studied, and the results showed that the surfaces of nano-titanium dioxide and calcium sulfate whiskers were successfully grafted with acrylonitrile. Owing to the introduction of new elements, such as acrylonitrile, nano-titanium dioxide and calcium sulfate whiskers have anti-aging properties. In comparison of the impact strength and tensile strength of TiO2-PAN/PP and TiO2-PAN/CSW-PAN/PP before aging, it can be proven that adding CSW-PAN can significantly enhance the mechanical properties of TiO2-PAN/CSW-PAN/PP. After 1000 h of aging, the tensile strength of the ternary composite TiO2-PAN/CSW-PAN/PP was 19.88 MPa when the addition amount of TiO2-PAN and CSW-PAN was 3%. Moreover, the impact strength of the ternary composite material TiO2-PAN/CSW-PAN/PP after 1000 h of aging is even better than that of non-aging pure PP materials, proving that the service life of improved PP products is extended, unnecessary waste and environmental pollution can be relieved, and the needs of specific engineering fields can be met.

Development and analysis of the physical and electrochemical characteristics of a nano titanium (IV) tungstomolybdate supported on polyethersulfone composite cation exchange membrane

In this study, a series of novel composite membranes were synthesized utilizing polyethersulfone (PES), sulfonated polyethersulfone (SPES) as base polymer and titanium tungstomolybdate (TWM) as an inorganic ion exchange resin. The membranes were fabricated through the solution casting technique. The composite membranes exhibited enhanced thermal and chemical stability, as well as improved oxidative stability. All the composite membranes demonstrated higher hydrophilicity, with the SPES-TWM composite membranes displaying the lowest contact angle of 65°. The composite membranes also displayed favorable water uptake (up to 26% for SPES-TWM) and lower methanol uptake (maximum 12% for SPES-TWM) and better mechanical stability (maximum of 40 MPa for SPES-TWM). The SPES-TWM composite membranes exhibited the maximum ion exchange capacity of 1.32 meq.g−1. The transport number of 0.95 was obtained for SPES-TWM, which is comparable to the Nafion-117 membrane. The proton conductivity of both membranes increased as the temperature increased. The maximum proton conductivity of 6.3 mScm−1 was observed for SPES-TWM at 60 °C.

Nano-Additives in Asphalt Binder: Bridging the Gap between Traditional Materials and Modern Requirements

This research delves into the realm of asphalt technology, exploring the potential of nano-additives to enhance traditional asphalt binder properties. Focusing on Nano-Titanium Dioxide (NT), Nano-Aluminum Oxide (NA), and Nano-Silica Oxide (NS), this study investigates the effects of incorporating these nanomaterials at varying dosages, ranging from 0% to 8%, on the asphalt binder’s performance. This study employs a series of experimental tests, including consistency, storage stability, rotational viscosity, mass loss due to aging, and rheological properties, to assess the impact of nano-additives on asphalt binder characteristics. The findings indicate a substantial improvement in the consistency of the asphalt binder with the addition of nanomaterials, particularly NS, which shows a 41% reduction in penetration at an 8% content and a notable increase in the softening point. The storage stability tests reveal that NS-modified asphalt exhibits superior stability compared to NT and NA, with a significantly lower ΔT increase. Furthermore, the investigation into rotational viscosity suggests that NS, despite increasing the binder’s viscosity, does not exceed the AASHTO M320 threshold, ensuring the binder’s workability. Aging tests demonstrate that NT, at lower concentrations, acts as an effective anti-aging agent, whereas NA and NS tend to increase the mass loss, impacting thermal stability. This study concludes that while each nanomaterial uniquely influences the asphalt binder’s properties, NS stands out in terms of enhancing the high-temperature performance and storage stability. Optimal dosages of 6% for NT and NA and 4% for NS are recommended based on the Overall Desirability analysis. This research bridges the gap between traditional asphalt materials and modern requirements, highlighting the transformative impact of nano-additives in advancing asphalt pavement technology.

Effects of Modified Distillers' Grains Biochar on Cadmium Forms in Purple Soil and Cadmium Uptake by Rice

Biochar and modified biochar have been widely used as remediation materials in heavy metal-contaminated agricultural soils. In order to explore economical and effective materials for the remediation of cadmium (Cd)-contaminated acidic purple soil, distillers 'grains were converted into distillers' grains biochar (DGBC) and modified using nano-titanium dioxide (Nano-TiO2) to produce two types of modified DGBCs:TiO2/DGBC and Fe-TiO2/DGBC. A rice pot experiment was used to investigate the effects of different biochar types and application rates (1%, 3%, and 5%) on soil properties, nutrient content, Cd bioavailability, Cd forms, rice growth, and Cd accumulation. The results showed that:① DGBC application significantly increased soil pH, cation exchange capacity (CEC), and nutrient content, with TiO2/DGBC and Fe-TiO2/DGBC exhibiting better effects. ② DGBC and modified DGBCs transformed Cd from soluble to insoluble forms, increasing residual Cd by 1.22% to 18.46% compared to that in the control. Cd bioavailability in soil decreased significantly, with available cadmium being reduced by 11.81% to 23.67% for DGBC, 7.64% to 43.85% for TiO2/DGBC, and 19.75% to 55.82% for Fe-TiO2/DGBC. ③ DGBC and modified DGBCs increased rice grain yield, with the highest yields observed at a 3% application rate:30.60 g·pot-1 for DGBC, 37.85 g·pot-1 for TiO2/DGBC, and 39.10 g·pot-1 for Fe-TiO2/DGBC, representing 1.13, 1.40, and 1.44 times the control yield, respectively. Cd content in rice was significantly reduced, with grain Cd content ranging from 0.24 to 0.30 mg·kg-1 for DGBC, 0.16 to 0.26 mg·kg-1 for TiO2/DGBC, and 0.14 to 0.24 mg·kg-1 for Fe-TiO2/DGBC. Notably, Cd content in rice grains fell below the food safety limit of 0.2 mg·kg-1 (GB2762-2022) at 5% for TiO2/DGBC and 3% and 5% for Fe-TiO2/DGBC. In conclusion, Nano-TiO2 modified DGBC effectively reduced the bioavailability of soil Cd through its own adsorption and influence on soil Cd forms distribution, thus reducing the absorption of Cd by rice and simultaneously promoting rice growth and improving rice yield. It is a type of Cd-contaminated soil remediation material with a potential application prospect. The results can provide scientific basis for farmland restoration and agricultural safety production of Cd-contaminated acidic purple soil.