Titanium Layer Research Articles

Formation of Hybrid Membranes for Water Desalination by the Method of Membrane Distillation

A method has been developed for the formation of hybrid membranes consisting of a hydrophilic microporous substrate and a hydrophobic nanofiber polymer layer deposited by electroforming. A track-etched membrane made of polyethylene terephthalate was used as a hydrophilic microporous substrate, on the surface of which a thin layer of titanium was applied by magnetron sputtering to ensure adhesion of the nanofiber layer. Simultaneously, the titanium coating was used to make a conductive track-etched membrane that served as a collector electrode. It is been shown that the application of this method for the formation of polymer coatings when used as a starting material for the formation of polyvinylidene fluoride nanofibers makes it possible to obtain a layer with highly hydrophobic properties, the water contact angle of the surface of which, depending on the deposition density, averages 143.3 ± 1.3°. A study of the morphology of the nanofiber coating shows that it has a microstructure typical of non-woven materials. The nanofibers forming the porous system of this layer have a wide range in size. The study of the molecular structure of the nanofiber layer by IR-Fourier spectroscopy and X-ray diffraction analysis showed that its structure is dominated by the β-phase, which is characterized by a maximum dipole moment. It is been shown that the hybrid membranes of the developed sample provide high separation selectivity when desalting an aqueous solution of sodium chloride with a concentration of 26.5 g/l by membrane distillation. The salt rejection coefficient for membranes with a nanofiber layer density from 20.7 ± 0.2 to 27.6 ± 0.2 g/m2 in the studied mode of the membrane distillation process is 99.97−99.98%. It has been established that the use of a highly hydrophobic nanofiber layer with a developed pore structure in combination with a hydrophilic microporous base makes it possible to increase the productivity of the membrane distillation process. The value of the maximum condensate flow through the membranes is on average 7.0 kg m2/h and its depends on the density of the deposited nanofiber layer.

Upconverting particles in near-infrared light-induced TiO2 photocatalysis: towards the optimal architecture of upconverter/photocatalyst systems.

Preparation of highly active core-shell/hybrid materials based on up-converting particles combined with semiconductors for photocatalytic application usually requires sophisticated and multi-step synthesis procedures. We propose a new design of a highly efficient NIR-driven photocatalytic system composed of spatially separated thin films of upconverting NaYF4:Yb,Tm particles (UCPs), and TiO2. Several samples of UCPs were prepared in the form of thin films and suspensions, directly coated with a titania layer or mixed with P25. Photocatalytic and photoelectrochemical studies have shown that thin film samples achieved significantly higher photocatalytic activity than their suspended counterparts. Moreover, the sample consisting of spatially separated layers of UCPs and P25 presented a significant photocatalytic activity and generated the highest photocurrent intensity. Separating the photocatalyst and upconverter layers allows for an interchangeable photocatalytic system active in a wide range of light.

Graphene Oxide-Doped Indium Oxide Buffer Film Sandwiched between Titanium Oxide Layers for the Development of Photosensitive Resistive Memory Devices.

Over the past decade, metal oxide semiconductors have attracted considerable attention because of their transparency, high intrinsic charge carrier mobility, and charge carrier density. Metal oxide semiconductors also provide a promising route to develop resistive memory devices because of the tunability of their conductivity via the removal of oxygen ions, forming oxygen vacancies that can act as electron donors. Here, this paper reports the fabrication of a resistive random-access memory (ReRAM) device with TiO2 and TiO2-x layers and introduces a solution-processed In2O3-graphene oxide (GO) buffer layer from a water-based precursor solution to tune the switching characteristics. The devices were compared with a ReRAM device with no buffer layer, and the device composition was optimized by tuning the GO concentration in the layers. The devices showed hysteresis under cyclically scanned bias between positive and negative voltages with clear switching between the low resistance state (LRS) and the high resistance state (HRS). The optimized device also showed a more than 3 orders of magnitude difference in resistance between the LRS and HRS and a stable current retention. The devices also showed photoresponsive behaviors. In the LRS, the current increased significantly under illumination, while in the HRS, the current deteriorated slowly when constantly illuminated. These results highlight the dual role of the GO flakes in the buffer layer by increasing the resistance in the HRS and providing a photoresponsive switching capability. The ReRAM device was connected to a TFT device, and its feasibility as a memory component in a digital circuit was successfully demonstrated. These results provide a new avenue for developing metal-oxide-based ReRAM devices with GO-containing active layers.

Effect of Anchoring Unit, N-Alkyl Chain Length, and Thickness of Titanium Dioxide Layer on the Efficiency of Dye-Sensitized Solar Cells (DSSCs) and Tandem DSSCs

Effect of Anchoring Unit, <i>N</i>-Alkyl Chain Length, and Thickness of Titanium Dioxide Layer on the Efficiency of Dye-Sensitized Solar Cells (DSSCs) and Tandem DSSCs

Investigation of Hf/Ti bilayers for the development of transition-edge sensor microcalorimeters.

The superconducting properties of 85 nm thick hafnium thin films with a 5 nm thick titanium layer on top have been investigated for three different geometries, that is, a film covering the entire 7 × 7 mm2 chip surface, bridges with a width of 200 μm and length up to 1800 μm, and bridges in the form of squares with sides from 100 to 1000 μm. The bridges were formed by a photolithographic lift-off process and are intended to be used as the main sensing element of a microcalorimeter based on a transition-edge sensor (TES) in experiments to determine the magnetic moment of neutrinos. Based on the measurements of the critical current, the critical temperature, and the width of the superconducting transition, we estimate the energy resolution δE of the TES prototypes, showing that it is possible to fabricate microcalorimeters with δE less than 1 eV using these films.

Improving Bioactivity of Anodic Titanium Oxide (ATO) Layers with Chlorine Ion Addition in Electrolytes

Appending diverse quantities of additional elements to the anodizing solution leads to the formation of a highly corrosion-resistant and biocompatible anodic Ti oxide (ATO) on the titanium surface. This study aims to investigate the synergistic effect of chlorine and sulfate ions in the anodizing solution on the formation mechanism and biocompatibility of anodized layers formed on pure Ti. For this purpose, sulfuric acid-based anodizing solutions with different molar ratios () of 0.25, 0.5, and 0.75, and total molars () of 1, 1.5, and 2 M, were utilized for galvanostatic anodizing conditions at different current densities. The response surface methodology was employed on these three anodizing parameters to optimize the quality of anodic Ti oxide layers. Voltage vs. time behavior, SEM surface morphology, and FE-SEM fractured cross-sectional observations were used to thoroughly discuss the formation mechanism. X-ray diffraction method, micro-Raman spectroscopy, and water contact angle measurements were performed to characterize the coatings. Corrosion properties of ATO layers were evaluated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization in simulated body fluid (Hanks’ solution). The total molar () is recognized as the most influential factor on the anodic oxide layer properties, and a three-step formation mechanism, based on the competition between the formation and dissolution of anodic Ti oxide, was proposed in detail. The sample anodized with a molar ratio () of 0.5 at a constant current density of 70 mA.cm-2 and a total molar of 1.5 M achieved maximum corrosion resistance with a corrosion current density of 2.138e-11 A.cm-2 compares to 1.39e-8 A.cm-2 for the substrate. Furthermore, the addition of chloride ions to the anodizing bath resulted in more hydrophilic surfaces, promoting the formation of granular hydroxyapatite (HAp) on the TAO coating with maximum corrosion resistance in the Hank solution.

Synthesis and Characterization of TiO2 Nanotubes for High-Performance Gas Sensor Applications

In this study, we investigated the fabrication, properties, and sensing applications of TiO2 nanotubes. A pure titanium metal sheet was used to demonstrate how titanium dioxide nanotubes can be used for gas-sensing applications through the electrochemical anodization method. Subsequently, X-ray diffraction indicated the crystallization of the titanium dioxide layer. Scanning electron microscopy and transmission electron microscopy then revealed the average diameter of the TiO2 nanotubes to be approximately 100 nm, with tube lengths ranging between 3 and 9 µm and the thickness of the nanotube walls being about 25 nm. This type of TiO2 nanotube was found to be suitable for NO2 gas sensor applications. With an oxidation time of 15 min, its detection of NO2 gas showed a good result at 250 °C, especially when exposed to a NO2 gas flow of 100 ppm, where a maximum NO2 gas response of 96% was obtained. The NO2 sensors based on the TiO2 nanotube arrays all exhibited a high level of stability, good reproducibility, and high sensitivity.

Electroless Copper Patterning on TiO2-Functionalized Mica for Flexible Electronics

The formation of conductive copper patterns on mica holds promise for developing cost-effective flexible electronics and sensing devices, though it is challenging due to the low adhesion of mica’s atomically flat surface. Herein, we present a wet-chemical method for copper patterning on flexible mica substrates via electroless copper deposition (Cu-ELD). The process involves pre-functionalizing 50 µm thick muscovite mica with a titanium dioxide (TiO2) layer, via a sol–gel dip-coating method with a titanium acetylacetonate-based sol. Photolithography is employed to selectively activate the TiO2-coated mica substrates for Cu-ELD, utilizing in situ photodeposited silver (Ag) nanoclusters as a catalyst. Copper is subsequently plated using a formaldehyde-based Cu-ELD bath, with the duration of deposition primarily determining the thickness and electrical properties of the copper layer. Conductive Cu layers with thicknesses in the 70–130 nm range were formed within 1–2 min of deposition, exhibiting an inverse relationship between plating time and sheet resistance, which ranged from 600 to 300 mΩ/sq. The electrochemical thickening of these layers to 1 μm further reduced the sheet resistance to 27 mΩ/sq. Finally, the potential of Cu-ELD patterning on TiO2-functionalized mica for creating functional sensing devices was demonstrated by fabricating a functional resistance temperature detector (RTD) on the titania surface.

Ambient Air-Synthesized CsPbBr3 Nanocrystals Coupled with TiO2 Film as an Efficient Hybrid Photoanode for Photoelectrochemical Methanol-to-Formaldehyde Conversion.

Due to its exceptional optoelectronic properties in the visible spectrum, cesium lead bromide (CsPbBr3) perovskite has attracted considerable attention in solar-driven organic transformations via photoelectrochemical (PEC) cells. However, the performance of the devices is adversely affected by electron-hole recombination occurring between a transparent conductive substrate, such as fluorine-doped tin dioxide (FTO), and a perovskite layer. Herein, to mitigate this issue, a compact layer of titanium dioxide (TiO2) was employed as both an electron transport layer and a hole blocking layer to diminish charge recombination while facilitating electron transfer in such perovskite material. At the oxidation peak potential of 0.70 V vs Ag/AgNO3, a hybrid photoanode of CsPbBr3/TiO2/FTO exhibited a significant increase in photocurrent density, from 15 to 41 μA/cm2, compared to a configuration without a TiO2 layer. Furthermore, the introduction of methanol as a hole scavenger in the PEC system using the hybrid photoanode facilitated the separation of electron-hole pairs, which led to an enhanced photocurrent density of 60 μA/cm2 and promoted the production of formaldehyde. High-performance liquid chromatography (HPLC) confirmed the generation of formaldehyde at a concentration of 26.69 μM with a Faradaic efficiency of 92% under an applied potential of 0.50 V vs Ag/AgNO3 for 60 min of PEC reaction. In addition to the enhanced PEC performance achieved from this hybrid photoanode, CsPbBr3 nanocrystals (NCs) in this work were synthesized by the modified one-pot method under ambient air, where highly uniform and high-purity NCs were obtained. This work signifies the groundbreaking exploration of CsPbBr3 NCs with TiO2 as a photoelectrode material in the organic-based PEC cells, which efficiently improved the interfacial charge transfer within the photoanode for the conversion of methanol to formaldehyde, marking a significant advancement in the field.

Formation of Graded TiO2 Layer on Ti Wire by Direct Alternating Current Discharge Plasma at Atmospheric Pressure

Although metallic materials have been used as load-bearing materials in dental and biomedical fields since they have good mechanical properties such as good ductility and strength, their aesthetic properties are inferior to those of ceramic or resin. To obtain aesthetically improved Ti dental devices, the formation of white titanium oxide on pure Ti dental devices was studied. Direct atmospheric pressure plasma (APP) treatment using alternating current was carried out on pure a Ti plate and wire. It was found that a titanium oxide layer with enough whiteness can be obtained on pure Ti wire using direct APP treatment. Although delamination of the titanium oxide layer was found after a bending test, the concept of functionally graded materials (FGMs) can overcome the shortcoming.

Leveraging Bayesian Optimization Software for Atomic Layer Deposition: Single-Objective Optimization of TiO2 Layers.

We demonstrate the application of free-to-use and easy-to-implement Bayesian optimization (BO) software to streamline atomic layer deposition (ALD) process optimization. By employing machine learning-based Bayesian optimization algorithms, we enhanced the silicon surface passivation quality of titanium dioxide layers deposited using titanium tetraisopropoxide (TTIP). Unlike classical designs of experimental methods, such as Box-Behnken or Plackett-Burman designs, which require a predefined set of experiments and can become resource intensive, BO offers several advantages. It dynamically updates the search strategy based on previous outcomes, allowing for efficient exploration of parameter spaces with fewer experimental runs. This adaptive approach is particularly advantageous in small-scale experiments or laboratories where time, resources, and materials are limited. In a single-objective optimization experiment, we identified constrained search spaces that limited further optimization, underscoring the importance of properly defined parameter bounds prior to the optimization process. Our findings highlight that Bayesian optimization can not only reduce time and resource costs associated with ALD process optimization but also support faster discovery of more optimal ALD process parameters, even with minimal prior knowledge of the deposition process or precursor chemistry.

Multi-Color Spaceplates in the Visible.

The ultimate miniaturization of any optical system relies on the reduction or removal of free-space gaps between optical elements. Recently, nonlocal flat optic components named "spaceplates" were introduced to effectively compress space for light propagation. However, space compression over the visible spectrum remains beyond the reach of current spaceplate designs due to their inherently limited operating bandwidth and functional inefficiencies in the visible range. Here, we introduce "multi-color" spaceplates performing achromatic space compression at three distinct color channels across the visible spectrum to markedly miniaturize color imaging systems. In this approach, we first design monochromatic spaceplates with high compression factors and high transmission amplitudes at visible wavelengths based on a scalable structure and dielectric materials widely used in the fabrication of meta-optical components. We then show that the dispersion-engineered combination of monochromatic spaceplates with suitably designed transmission responses forms multicolor spaceplates that function achromatically. The proposed multicolor spaceplates, composed of amorphous titanium dioxide and silicon dioxide layers, efficiently replace free-space volumes with compression ratios as high as 4.6, beyond what would be achievable by a continuously broadband spaceplate made of the same materials. Our strategy for designing monochromatic and multicolor spaceplates, along with the presented theoretical and computational results, show that strong space-compression effects can be achieved in the visible range. Our findings may ultimately enable a new generation of ultrathin optical devices for various applications.

Novel cytotoxicity of nano-coated orthodontic micro-implants: An in vitro study

Objectives: Many attempts have been made to modify the surface of orthodontic micro-implants and prevent the development of microbes by coating them with antimicrobial nanoparticles (NPs). The purpose of the present study was to evaluate the cytotoxicity of different NPs, namely, TiO2 and zinc oxide (ZnO) NPs, that are used to coat titanium orthodontic micro-implants. Material and Methods: Thirty orthodontic micro-implants were included in this study. Those were divided into three groups: control group without coating, TiO2-coated orthodontic micro-implants, and TiO2- and ZnO-coated orthodontic micro-implants. Scanning electron microscope, energy-dispersive spectroscopy (EDS), and cytotoxicity tests were applied for all groups. Results: The results of scanning electron microscopy and EDS showed effective deposition of the titanium oxide layer onto the micro-implants. The ZnO layer applied on the micro-implants exhibited superior physicochemical characteristics in comparison to the uncoated samples with no significant cytotoxicity. Conclusion: Both NPs showed biocompatibility with the oral tissues.

Ultra-broadband polarization-insensitive versatile solar thermal harvester

Sustainable and Renewable Energy is essential because it's non-polluted and available in nature. Solar energy is the most important of them all as its the essential of them all. Sun energy is a clean and finest alternative to renewable energy sources. The slotted cylinder-shaped Mxene-based resonator solar absorber (SCMRSA) achieved an average of 95.06 % efficient absorption. The MXene material is used as a resonating material above the titanium oxide layer based on the MXene layer. The wide angle of incidence is achieved which is analyzed by changing the different angles of incidence. The E-field response is also observed for the TE and TM modes. The results show a similar response for both TE and TM modes. The optimization of the structure is also observed for different variable variations and the final optimized design is used for the highly efficient absorptance results. The SCMRSA is also applicable for various solar thermal applications and energy harvesters.

Plasma coloring of Ti via air atmospheric pressure plasma jet for dentistry

The aesthetic appeal of titanium dental implants is compromised by unattractive coloration, and extended exposure to bodily fluids can result in the release of ions, potentially causing infection or inflammation. This study introduces a direct method for oxidizing titanium through plasma coloring to enhance biocompatibility. Utilizing a tornado-type atmospheric pressure plasma jet (APPJ) with compressed dry air as the working gas, sub-stoichiometric titanium oxide was produced on sample surfaces. Analysis of reactive oxygen species (ROS) in air plasma via optical emission spectroscopy offers valuable insights into the interaction between plasma and the surface during the oxidation process. Quantification of surface coloration in titanium samples before and after treatment with air-APPJ was conducted using CIE chromaticity diagrams and color temperature analysis. This analytical approach enabled the assessment of thermal and plasma-chemical impacts of plasma coloring on the development of the sub-stoichiometric titanium oxide layer. The resulting oxide layers from the APPJ process exhibited a vibrant golden shade, along with enhanced surface hydrophilicity, improved anticorrosion properties, and enhanced cellular responses.

Regulating the interfacial structure in percolating graphite nanoplate/PVDF composites via TiO2 as an interlayer towards meliorative dielectric performances

Polymer nanocomposites combining large dielectric permittivity (ε′) but low loss along with high breakdown strength (Eb) have garnered significant attention in the fields of electronic devices and power systems. To concurrently accomplish these desirable performances in pristine graphite nanoplates (GNP)/poly(vinylidene fluoride, PVDF) composites, the GNP were initially encased by a layer of anatase-type titanium dioxide (TiO2) shell, and then incorporated into PVDF to investigate the effect of TiO2 interlayer on the dielectric properties of the nanocomposites, specifically in relation to the thickness of the TiO2 shell and the nanofiller concentration. The TiO2 shell acts as a barrier layer prohibiting the electronic percolating, thus significantly reducing the dielectric loss and leakage conductivity of the GNP@TiO2/PVDF. Moreover, it not only alleviates the strong dielectric mismatch between GNP and PVDF, which restrains local electric field distortion, but also introduces charge traps, raising the energy barrier height for captured charge detrapping and preventing the growth of electric trees and subsequently promoting the Eb. For example, the PVDF with 20 wt% of GNP@TiO2 exhibited good comprehensive dielectric performances: ε′ of 50.63, loss factor of 0.071 (100 Hz) and Eb of 7.89 kV/mm. Additionally, tailoring the TiO2’s thickness can simultaneously modulate the overall dielectric parameters in the GNP@TiO2/PVDF. Theoretical fitting of experimental data via Havriliak-Negami equation uncovers the underlying polarization mechanism and the interlayer’s impact on charge migration. This work provides an efficient method for developing and producing polymeric nanodielectrics that simultaneously incorporate increased Eb with high ε′ but low loss for potential use in power devices and microelectronic devices.

Structural state and physical-mechanical properties of multilayer vacuum arc Ti/TiN coating

Abstract. Problem. Increasing the resource of the cutting tools in conditions of variable load is of great importance, as it affects not only the cost of production but also the competitiveness of the enterprise. A wide range of properties of vacuum arc multilayer coatings allows them to be used in mechanical engineering to increase the performance of the tools in the variable conditions of cutting. Goal. The goal is to study the structural state and physical and mechanical properties of vacuum arc multilayer Ti/TiN coatings. To achieve the goal, it is necessary to analyze the effect of the thickness of the titanium layer and the amount of negative stress on the substrate on the structure, stress-strain state, and physical and mechanical properties of the multilayer Ti/TiN coating with relatively thick layers of titanium nitride. Methodology. Multilayer Ti/TiN coatings were obtained in the Bulat-6 vacuum-arc installation. The study of mechanical characteristics was carried out by the indentation method using the MicronGama microindenter. Structural studies of the samples were carried out on a DRON-3M diffractometer. Electron microscopic studies were performed on a JEOL JSM-840 scanning electron microscope. Originality. It was found that in titanium nitride layers with a thickness of 300 nm or more, a texture develops when a voltage is applied to the substrate. The degree of texture perfection increases with increasing layer thickness. When the thickness of the titanium layer is from 30 nm to 250 nm, the development of the stress-strain state in the titanium nitride layers takes place without significant relaxation. The mechanical properties of the Ti/TiN multilayer coating remain quite high (hardness 33.7...36.3 GPa with a modulus of elasticity 413...434 GPa) when the thickness of the titanium layer is less than 125 nm. Practical value. Increasing the crack resistance of Ti/TiN multilayer coatings due to the introduction of titanium layers makes their use promising for hard loads.

Tuning the toughness, strength, and biological properties of functionally graded alumina/titania-based composites for use in bone repair applications

In this study, functionally graded composite (FGC) was prepared using a high-energy ball mill by fabricating five layers of alumina (Al2O3), titania (TiO2), hydroxyapatite (HA), and iron oxide (Fe3O4), which were sintered at 1100 °C to create an FGC sample. Scanning electron microscopy (SEM), inductively coupled plasma-atomic emission spectroscopy (ICP-AES), and weight loss measurements were used to assess bioactivity and biodegradation after immersing samples in simulated body fluid (SBF). Also, the antimicrobial activity and biocompatibility of these layers were evaluated. Furthermore, their electrical, dielectric, and mechanical properties were examined. The results revealed that all sintered layers were bioactive, and adding HA and Fe3O4 enhanced this desired property. Also, S. aureus bacterial growth was inhibited by TiO2 and Fe3O4. Fortunately, the sintered layers showed no cytotoxic effect, validating the ICP findings that demonstrated acceptable biodegradation. Adding HA and Fe3O4 enhanced fracture toughness in another hopeful outcome, which is crucial for biomaterial efficacy and long-term therapeutic success. Moreover, the compressive strength of all the layers and the FGC sample was 191.7, 182.2, 171.18, 159.8, 142.5, and 171.1 MPa. Layers 3, 4, and 5 notably had a compressive strength similar to cortical bone. This means that implanting these layers into human bone will protect the bone around them from stress-shielding action. Finally, the successive increase in HA/Fe3O4 contents increased the electrical conductivity. Accordingly, the prepared FGC sample and its layers are attractive bone substitute materials.

Morphological Characterization and Tribological Properties of TiCoNi Alloy Coatings on Ti–6Al–4V Alloy via Laser Deposition

The goal of this work is to improve the Ti–6Al–4V alloy's hardness and tribological behavior. Coaxial laser surface cladding was used to develop intermetallic layers of nickel (Ni), cobalt (Co), and titanium (Ti). Laser power of 900 W, beam spot size of 3 mm, powder feed rate of 1.0 g/min, and gas flow rate of 1.2 L/min are the optimized parameters used for laser depositions. The laser scan speeds were adjusted between 0.6 and 1.2 m/min. Investigations were conducted into the effects of powder admixture and laser parameters on the fabricated coatings' microstructure, tribological behavior and hardness. X-ray diffractometry (XRD), energy dispersive spectroscopy (EDS) with Scanning electron microscopy (SEM) was employed for the characterization of the microstructural evolution and phase identification, respectively. Additionally, the tribological experiment was conducted via UMT-2 –CETR reciprocating tribometer, and the coatings’ micro-hardness characteristics were examined using EmcoTEST DURASCAN. The micrographs exhibit no signs of porousness, cracks, or stress introduction, according to the results. For every manufactured sample, good metallurgical adhesion was obtained. By comparing the hardness of the ternary coating (Co–Ni–10Ti deposited at a scan speed of 1.2 m/min, with a hardness of 980 HV) to the substrate (Ti–6Al–4V, with a hardness of 330 HV), a hardness increase of approximately 2.96 times was observed. Furthermore, the Co–Ni–10Ti coating, deposited at a scan speed of 1.2 m/min, demonstrated a 51.1% reduction in the coefficient of friction (COF) compared to the base alloy, indicating superior anti-wear performance. The enhanced properties are attributed to the formation of hard intermetallic compounds such as Ti–Co, Co2Ti, Al5Co2, and Ni3Ti, along with their uniform distribution and finely tuned grain sizes.

Combustion synthesis of the (Ti,Zr)B2-(Zr,Ti)C eutectic composites: Structure formation and properties

The macrokinetic characteristics of combustion of the quaternary Ti-Zr-B-C mixture as well as the mechanism and stages of phase formation for the synthesis products were investigated. The mechanical and thermophysical properties of the hot-pressed boride/carbide ceramics with eutectic composition (Ti,Zr)B2-43%at.(Zr,Ti)C were measured. Preliminary mechanical alloying (MA) of the (Zr + Ti) mixture was shown to yield Ti/Zr granules having a laminar structure and consisting of alternating layers of titanium, zirconium, and (Zr,Ti)ss solid solution. The method used to prepare reaction mixtures and the initial temperature T0 increased within the range of 20–370 °C have virtually no effect on combustion temperature, which is 2260–2400 °C, while higher T0 increases the combustion rate by a factor of 1.5–2. The use of MA Ti/Zr granules reduces the combustion rate as well as the specific heat release amount and the heat release rate. Time-resolved X-ray diffraction data showed that binary carbides (Zr1-xTix)C and diborides (Ti1-yZry)B2 of variable stoichiometry are formed in the combustion wave of the Ti-Zr-B-C reaction mixtures within less than 0.25 s. The carbide and diboride phases are formed simultaneously; the use of MA Ti/Zr granules in the reaction mixtures reduces the content of solid solutions of variable stoichiometry among the reaction products. The ceramics fabricated using a combination of combustion synthesis and hot pressing have a dense and homogeneous structure that consist of bonded grains of the diboride (Ti0.80Zr0.20)B2 and carbide (Zr0.83Ti0.17)C phases having the following properties: density, 5.3 g/cm3; hardness, 22.9 GPa; fracture toughness, 4.7 MPa m0.5; heat capacity, 0.52 J/(g·K); thermal diffusivity, 11.67 mm2/s; and thermal conductivity, 33.28 W/(m·K).