Tibiofemoral Forces Research Articles

The Influence of Component Alignment and Ligament Properties on Tibiofemoral Contact Forces in Total Knee Replacement

The study objective was to investigate the influence of coronal plane alignment and ligament properties on total knee replacement (TKR) contact loads during walking. We created a subject-specific knee model of an 83-year-old male who had an instrumented TKR. The knee model was incorporated into a lower extremity musculoskeletal model and included deformable contact, ligamentous structures, and six degrees-of-freedom (DOF) tibiofemoral and patellofemoral joints. A novel numerical optimization technique was used to simultaneously predict muscle forces, secondary knee kinematics, ligament forces, and joint contact pressures from standard gait analysis data collected on the subject. The nominal knee model predictions of medial, lateral, and total contact forces during gait agreed well with TKR measures, with root-mean-square (rms) errors of 0.23, 0.22, and 0.33 body weight (BW), respectively. Coronal plane component alignment did not affect total knee contact loads, but did alter the medial-lateral load distribution, with 4 deg varus and 4 deg valgus rotations in component alignment inducing +17% and -23% changes in the first peak medial tibiofemoral contact forces, respectively. A Monte Carlo analysis showed that uncertainties in ligament stiffness and reference strains induce ±0.2 BW uncertainty in tibiofemoral force estimates over the gait cycle. Ligament properties had substantial influence on the TKR load distributions, with the medial collateral ligament and iliotibial band (ITB) properties having the largest effects on medial and lateral compartment loading, respectively. The computational framework provides a viable approach for virtually designing TKR components, considering parametric uncertainty and predicting the effects of joint alignment and soft tissue balancing procedures on TKR function during movement.

The effect of barefoot and barefoot inspired footwear running on tibiofemoral kinetics

PurposeThe current investigation aimed to examine the effects of running barefoot and in conventional and barefoot inspired footwear on the loads borne by the tibiofemoral joint.MethodsFifteen male participants ran at 4.0 m/s over a force platform whilst running barefoot, in barefoot inspired footwear and also in conventional footwear. Lower body kinematics were collected using an eight-camera motion capture system. Peak tibiofemoral force, peak tibiofemoral stress, and tibiofemoral load rate were extracted and compared between footwear via one-way repeated measures ANOVA.ResultsThe results showed that the tibiofemoral instantaneous load rate was significantly lower in conventional footwear (106.63 BW/s) in comparison with barefoot running (173.87 BW/s), Vibram Five Fingers (160.17 BW/s), Merrell (155.32 BW/s), Inov-8 (167.79 BW/s), and Nike Free (144.72 BW/s).ConclusionsThis indicates that running barefoot and in barefoot inspired footwear may place runners at increased risk from running-related tibiofemoral pathologies.

FE analysis of the effects of simplifications in experimental testing on micromotions of uncemented femoral knee implants.

Experimental testing of orthopaedic implants requires simplifications concerning load application and activities being analyzed. This computational study investigated how these simplifications affect micromotions at the bone-implant interface of an uncemented femoral knee implant. As a basis, validated in vivo loads of the stance phase of gait and a deep knee bend were adopted. Eventually, three configurations were considered: (i) simulation of the complete loading cycle; (ii) inclusion of only tibiofemoral loads (ignoring patellofemoral loads); and (iii) applying only a single peak tibiofemoral force. For all loading conditions the largest micromotions found at the proximal anterior flange. Without the patellofemoral force, peak micromotions increased 6% and 22% for gait and deep knee bend, respectively. By applying a single peak tibiofemoral force micromotions were overestimated. However, the peak micromotions corresponded to the maximum tibiofemoral force, and strong micromotion correlations were found between a complete loading cycle and a single peak load (R(2) = 0.73 and R(2) = 0.89 for gait and deep knee bend, respectively). Deep knee bend resulted in larger micromotions than gait. Our study suggests that a simplified peak force can be used to assess the stability of cementless femoral components. For more robust testing, implants should be subjected to different loading modes. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:812-819, 2016.

A dynamic multibody model of the physiological knee to predict internal loads during movement in gravitational field

Obtaining tibio-femoral (TF) contact forces, ligament deformations and loads during daily life motor tasks would be useful to better understand the aetiopathogenesis of knee joint diseases or the effects of ligament reconstruction and knee arthroplasty. However, methods to obtain this information are either too simplified or too computationally demanding to be used for clinical application. A multibody dynamic model of the lower limb reproducing knee joint contact surfaces and ligaments was developed on the basis of magnetic resonance imaging. Several clinically relevant conditions were simulated, including resistance to hyperextension, varus–valgus stability, anterior–posterior drawer, loaded squat movement. Quadriceps force, ligament deformations and loads, and TF contact forces were computed. During anterior drawer test the anterior cruciate ligament (ACL) was maximally loaded when the knee was extended (392 N) while the posterior cruciate ligament (PCL) was much more stressed during posterior drawer when the knee was flexed (319 N). The simulated loaded squat revealed that the anterior fibres of ACL become inactive after 60° of flexion in conjunction with PCL anterior bundle activation, while most components of the collateral ligaments exhibit limited length changes. Maximum quadriceps and TF forces achieved 3.2 and 4.2 body weight, respectively. The possibility to easily manage model parameters and the low computational cost of each simulation represent key points of the present project. The obtained results are consistent with in vivo measurements, suggesting that the model can be used to simulate complex and clinically relevant exercises.

A subject-specific musculoskeletal modeling framework to predict in vivo mechanics of total knee arthroplasty.

Musculoskeletal (MS) models should be able to integrate patient-specific MS architecture and undergo thorough validation prior to their introduction into clinical practice. We present a methodology to develop subject-specific models able to simultaneously predict muscle, ligament, and knee joint contact forces along with secondary knee kinematics. The MS architecture of a generic cadaver-based model was scaled using an advanced morphing technique to the subject-specific morphology of a patient implanted with an instrumented total knee arthroplasty (TKA) available in the fifth "grand challenge competition to predict in vivo knee loads" dataset. We implemented two separate knee models, one employing traditional hinge constraints, which was solved using an inverse dynamics technique, and another one using an 11-degree-of-freedom (DOF) representation of the tibiofemoral (TF) and patellofemoral (PF) joints, which was solved using a combined inverse dynamic and quasi-static analysis, called force-dependent kinematics (FDK). TF joint forces for one gait and one right-turn trial and secondary knee kinematics for one unloaded leg-swing trial were predicted and evaluated using experimental data available in the grand challenge dataset. Total compressive TF contact forces were predicted by both hinge and FDK knee models with a root-mean-square error (RMSE) and a coefficient of determination (R2) smaller than 0.3 body weight (BW) and equal to 0.9 in the gait trial simulation and smaller than 0.4 BW and larger than 0.8 in the right-turn trial simulation, respectively. Total, medial, and lateral TF joint contact force predictions were highly similar, regardless of the type of knee model used. Medial (respectively lateral) TF forces were over- (respectively, under-) predicted with a magnitude error of M < 0.2 (respectively > -0.4) in the gait trial, and under- (respectively, over-) predicted with a magnitude error of M > -0.4 (respectively < 0.3) in the right-turn trial. Secondary knee kinematics from the unloaded leg-swing trial were overall better approximated using the FDK model (average Sprague and Geers' combined error C = 0.06) than when using a hinged knee model (C = 0.34). The proposed modeling approach allows detailed subject-specific scaling and personalization and does not contain any nonphysiological parameters. This modeling framework has potential applications in aiding the clinical decision-making in orthopedics procedures and as a tool for virtual implant design.

Voluntary Enhanced Cocontraction of Hamstring Muscles During Open Kinetic Chain Leg Extension Exercise

Background: A number of research studies provide evidence that hamstring cocontraction during open kinetic chain knee extension exercises enhances tibiofemoral (TF) stability and reduces the strain on the anterior cruciate ligament. Purpose: To determine the possible increase in hamstring muscle coactivation caused by a voluntary cocontraction effort during open kinetic chain leg-extension exercises, and to assess whether an intentional hamstring cocontraction can completely suppress the anterior TF shear force during these exercises. Study Design: Descriptive laboratory study. Methods: Knee kinematics as well as electromyographic activity in the semitendinosus (ST), semimembranosus (SM), biceps femoris (BF), and quadriceps femoris muscles were measured in 20 healthy men during isotonic leg extension exercises with resistance (R) ranging from 10% to 80% of the 1-repetition maximum (1RM). The same exercises were also performed while the participants attempted to enhance hamstring coactivation through a voluntary cocontraction effort. The data served as input parameters for a model to calculate the shear and compressive TF forces in leg extension exercises for any set of coactivation patterns of the different hamstring muscles. Results: For R≤ 40% 1RM, the peak coactivation levels obtained with intentional cocontraction (l) were significantly higher (P < 10–3) than those obtained without intentional cocontraction (l0). For each hamstring muscle, maximum level l was reached at R = 30% 1RM, corresponding to 9.2%, 10.5%, and 24.5% maximum voluntary isometric contraction (MVIC) for the BF, ST, and SM, respectively, whereas the ratio l/l0 reached its maximum at R = 20% 1RM and was approximately 2, 3, and 4 for the BF, SM, and ST, respectively. The voluntary enhanced coactivation level l obtained for R≤ 30% 1RM completely suppressed the anterior TF shear force developed by the quadriceps during the exercise. Conclusion: In leg extension exercises with resistance R≤ 40% 1RM, coactivation of the BF, SM, and ST can be significantly enhanced (up to 2, 3, and 4 times, respectively) by a voluntary hamstring cocontraction effort. The enhanced coactivation levels obtained for R≤ 30% 1RM can completely suppress the anterior TF shear force developed by the quadriceps during the exercise. Clinical Relevance: This laboratory study suggests that leg extension exercise with intentional hamstring cocontraction may have the potential to be a safe and effective quadriceps-strengthening intervention in the early stages of rehabilitation programs for anterior cruciate ligament injury or reconstruction recovery. Further studies, including clinical trials, are needed to investigate the relevance of this therapeutic exercise in clinical practice.

Influences of alignment and obesity on knee joint loading in osteoarthritic gait

To determine the influences of frontal plane knee alignment and obesity on knee joint loads in older, overweight and obese adults with knee osteoarthritis (OA). Cross-sectional investigation of alignment and obesity on knee joint loads using community dwelling older adults (age ≥ 55 years; 27 kg m(-2) ≥ body mass or body mass index (BMI) ≤ 41 kg m(-2); 69% female) with radiographic knee OA that were a subset of participants (157 out of 454) enrolled in the Intensive Diet and Exercise for Arthritis (IDEA) clinical trial. A higher BMI was associated with greater (P = 0.0006) peak knee compressive forces [overweight, 2411 N (2182, 2639), class 1 obesity, 2772 N (2602, 2943), class 2+ obesity, 2993 N (2796, 3190)] and greater (P = 0.004) shear forces [overweight, 369 N (322, 415), class 1 obesity, 418 N (384, 453), class 2+ obesity, 472 N (432, 513)], independent of alignment, and varus alignment was associated (P < 0.0001) with greater peak external knee adduction moments, independent of BMI [valgus, 18.7 Nm (15.1, 22.4), neutral, 27.7 Nm (24.0, 31.4), varus, 37.0 Nm (34.4, 39.7)]. BMI and alignment were associated with different joint loading measures; alignment was more closely associated with the asymmetry or imbalance of loads across the medial and lateral knee compartments as reflected by the frontal plane external adduction moment, while BMI was associated with the magnitude of total tibiofemoral force. These data may be useful in selecting treatment options for knee OA patients (e.g., diet to reduce compressive loads or bracing to change alignment).

THE EFFECT OF A SIX WEEK ECCENTRIC HAMSTRING STRENGTHENING PROTOCOL ON ANTERIOR TIBIO-FEMORAL TRANSLATION

BackgroundThe anterior cruciate ligament (ACL) is the main source of anterior knee joint stability and excessive anterior tibio-femoral translation (ATFT) (>5mm) can be a risk factor for ACL injury (Alentorn-Geli...

Changes in tibiofemoral forces due to variations in muscle activity during walking

Muscles induce large forces in the tibiofemoral joint during walking and thereby influence the health of tissues like articular cartilage and menisci. It is possible to walk with a wide variety of muscle coordination patterns, but the effect of varied muscle coordination on tibiofemoral contact forces remains unclear. The goal of this study was to determine the effect of varied muscle coordination on tibiofemoral contact forces. We developed a musculoskeletal model of a subject walking with an instrumented knee implant. Using an optimization framework, we calculated the tibiofemoral forces resulting from muscle coordination that reproduced the subject's walking dynamics. We performed a large set of optimizations in which we systematically varied the coordination of muscles to determine the influence on tibiofemoral force. Model-predicted tibiofemoral forces arising with minimum muscle activation matched in vivo forces measured during early stance, but were greater than in vivo forces during late stance. Peak tibiofemoral forces during late stance could be reduced by increasing the activation of the gluteus medius, uniarticular hip flexors, and soleus, and by decreasing the activation of the gastrocnemius and rectus femoris. These results suggest that retraining of muscle coordination could substantially reduce tibiofemoral forces during late stance.

Evaluation of a musculoskeletal model with prosthetic knee through six experimental gait trials

Knowledge of the forces acting on musculoskeletal joint tissues during movement benefits tissue engineering, artificial joint replacement, and our understanding of ligament and cartilage injury. Computational models can be used to predict these internal forces, but musculoskeletal models that simultaneously calculate muscle force and the resulting loading on joint structures are rare. This study used publicly available gait, skeletal geometry, and instrumented prosthetic knee loading data [1] to evaluate muscle driven forward dynamics simulations of walking. Inputs to the simulation were measured kinematics and outputs included muscle, ground reaction, ligament, and joint contact forces. A full body musculoskeletal model with subject specific lower extremity geometries was developed in the multibody framework. A compliant contact was defined between the prosthetic femoral component and tibia insert geometries. Ligament structures were modeled with a nonlinear force–strain relationship. The model included 45 muscles on the right lower leg. During forward dynamics simulations a feedback control scheme calculated muscle forces using the error signal between the current muscle lengths and the lengths recorded during inverse kinematics simulations. Predicted tibio-femoral contact force, ground reaction forces, and muscle forces were compared to experimental measurements for six different gait trials using three different gait types (normal, trunk sway, and medial thrust). The mean average deviation (MAD) and root mean square deviation (RMSD) over one gait cycle are reported. The muscle driven forward dynamics simulations were computationally efficient and consistently reproduced the inverse kinematics motion. The forward simulations also predicted total knee contact forces (166N<MAD<404N, 212N<RMSD<448N) and vertical ground reaction forces (66N<MAD<90N, 97N<RMSD<128N) well within 28% and 16% of experimental loads, respectively. However the simplified muscle length feedback control scheme did not realistically represent physiological motor control patterns during gait. Consequently, the simulations did not accurately predict medial/lateral tibio-femoral force distribution and muscle activation timing.

The effects of childhood obesity on compressive tibiofemoral force and muscle functions during normal walking

The effects of childhood obesity on compressive tibiofemoral force and muscle functions during normal walking

A comparison of slow, uphill and fast, level walking on lower extremity biomechanics and tibiofemoral joint loading in obese and nonobese adults

We determined if slow, uphill walking (0.75 m/s, 6°) reduced tibiofemoral (TF) loading compared to faster, level walking (1.50 m/s) in obese and nonobese adults. We collected kinematic, kinetic, and electromyographic data as 9 moderately obese and 10 nonobese participants walked on a dual-belt instrumented treadmill. We used OpenSim to scale a musculoskeletal model and calculate joint kinematics, kinetics, muscle forces, and TF forces. Compressive TF forces were greater in the obese adults during both speed/grade combinations. During level walking, obese participants walked with a straighter leg than nonobese participants, resulting in early stance vasti muscle forces that were similar in the obese and nonobese participants. Early stance peak compressive TF forces were reduced by 23% in obese (2,352 to 1,811 N) and 35% in nonobese (1,994 to 1,303 N) individuals during slow, uphill walking compared to brisk level walking. Late stance peak TF forces were similar across speeds/grades, but were greater in obese (∼2,900 N) compared to nonobese (∼1,700 N) individuals. Smaller early stance TF loads and loading rates suggest that slow, uphill walking may be appropriate exercise for obese individuals at risk for musculoskeletal pathology or pain.

Towards a Fine-tunable Tibial Implant for the in-vivo Correction of Ligament Imbalance Resulting from Patient Morpho-functional Evolution

The main purpose of this paper is to summarize the results of our research to develop a new generation of instrumented knee implant. The proposed implant is supposed to provide the clinician with significant information on the tibiofemoral force distribution during normal walking in order to assess the ligament imbalance and correct it as needed. The electronics embedded into the implant to achieve this task should be miniaturized enough to fit the limited space available inside it. These electronics should also be self-powered to eliminate the need for periodic replacement of a rechargeable battery or the need for an external source of electric power. Therefore, the possibility to use the piezoceramics not only as imbalance sensors but also as energy harvesters within the tibial baseplate of knee implant has been investigated by means of theoretical modeling and experimental trials.

The Effects of Walking Speed on Tibiofemoral Loading Estimated Via Musculoskeletal Modeling

Net muscle moments (NMMs) have been used as proxy measures of joint loading, but musculoskeletal models can estimate contact forces within joints. The purpose of this study was to use a musculoskeletal model to estimate tibiofemoral forces and to examine the relationship between NMMs and tibiofemoral forces across walking speeds. We collected kinematic, kinetic, and electromyographic data as ten adult participants walked on a dual-belt force-measuring treadmill at 0.75, 1.25, and 1.50 m/s. We scaled a musculoskeletal model to each participant and used OpenSim to calculate the NMMs and muscle forces through inverse dynamics and weighted static optimization, respectively. We determined tibiofemoral forces from the vector sum of intersegmental and muscle forces crossing the knee. Estimated tibiofemoral forces increased with walking speed. Peak early-stance compressive tibiofemoral forces increased 52% as walking speed increased from 0.75 to 1.50 m/s, whereas peak knee extension NMMs increased by 168%. During late stance, peak compressive tibiofemoral forces increased by 18% as speed increased. Although compressive loads at the knee did not increase in direct proportion to NMMs, faster walking resulted in greater compressive forces during weight acceptance and increased compressive and anterior/posterior tibiofemoral loading rates in addition to a greater abduction NMM.

Effects of workload and pedalling cadence on knee forces in competitive cyclists

Limited evidence showed that higher workload increases knee forces without effects from changes in pedalling cadence. This study assessed the effects of workload and cadence on patellofemoral and tibiofemoral joint forces using a new model. Right pedal force and lower limb joint kinematics were acquired for 12 competitive cyclists at two levels of workload (maximal and second ventilatory threshold) at 90 and 70 rpm of pedalling cadence. The maximal workload showed 18% larger peak patellofemoral compressive force PFC (large effect size, ES) than the second ventilatory threshold workload (90 rpm). In the meantime, the 90-rpm second ventilatory threshold was followed by a 29% smaller PFC force (large ES) than the 70-rpm condition. Normal and anterior tibiofemoral compressive forces were not largely affected by changes in workload or pedalling cadence. Compared to those of previous studies, knee forces normalized by workload were larger for patellofemoral (mean = 19 N/J; difference to other studies = 20–45%), tibiofemoral compressive (7.4 N/J; 20–572%), and tibiofemoral anterior (0.5 N/J; 60–200%) forces. Differences in model design and testing conditions (such as workload and pedalling cadence) may affect prediction of knee joint forces.

Joint Torques and Joint Reaction Forces During Squatting With a Forward or Backward Inclined Smith Machine

We developed a biomechanical model to determine the joint torques and loadings during squatting with a backward/forward-inclined Smith machine. The Smith squat allows a large variety of body positioning (trunk tilt, foot placement, combinations of joint angles) and easy control of weight distribution between forefoot and heel. These distinctive aspects of the exercise can be managed concurrently with the equipment inclination selected to unload specific joint structures while activating specific muscle groups. A backward (forward) equipment inclination decreases (increases) knee torque, and compressive tibiofemoral and patellofemoral forces, while enhances (depresses) hip and lumbosacral torques. For small knee flexion angles, the strain-force on the posterior cruciate ligament increases (decreases) with a backward (forward) equipment inclination, whereas for large knee flexion angles, this behavior is reversed. In the 0 to 60 degree range of knee flexion angles, loads on both cruciate ligaments may be simultaneously suppressed by a 30 degree backward equipment inclination and selecting, for each value of the knee angle, specific pairs of ankle and hip angles. The anterior cruciate ligament is safely maintained unloaded by squatting with backward equipment inclination and uniform/forward foot weight distribution. The conditions for the development of anterior cruciate ligament strain forces are clearly explained.

The Application of Computer Musculoskeletal Modeling and Simulation to Investigate Compressive Tibiofemoral Force and Muscle Functions in Obese Children

This study aimed to utilize musculoskeletal modelling and simulation to investigate the compressive tibiofemoral force and individual muscle function in obese children. We generated a 3D muscle-driven simulation of eight obese and eight normal-weight boys walking at their self-selected speed. The compressive tibiofemoral force and individual muscle contribution to the support and progression accelerations of center of mass (COM) were computed for each participant based on the subject-specific model. The simulated results were verified by comparing them to the experimental kinematics and EMG data. We found a linear relationship between the average self-selected speed and the normalized peak compressive tibiofemoral force (R 2 = 0.611). The activity of the quadriceps contributed the most to the peak compressive tibiofemoral force during the stance phase. Obese children and nonobese children use similar muscles to support and accelerate the body COM, but nonobese children had significantly greater contributions of individual muscles. The obese children may therefore adopt a compensation strategy to avoid increasing joint loads and muscle requirements during walking. The absolute compressive tibiofemoral force and muscle forces were still greater in obese children. The long-term biomechanical adaptations of the musculoskeletal system to accommodate the excess body weight during walking are a concern.

Anti‐gravity treadmills are effective in reducing knee forces

Lower body positive pressure (LBPP) treadmills permit significant unweighting of patients and have the potential to enhance recovery following lower limb surgery. We determined the efficacy of an LBPP treadmill in reducing knee forces in vivo. Subjects, implanted with custom electronic tibial prostheses to measure forces in the knee, were tested on a treadmill housed within a LBPP chamber. Tibiofemoral forces were monitored at treadmill speeds from 1.5 mph (0.67 m/s) to 4.5 mph (2.01 m/s), treadmill incline from -10° to +10°, and four treadmill chamber pressure settings adjusted to decrease net treadmill reaction force from 100% to 25% of the subject's body weight (BW). The peak axial tibiofemoral force ranged from 5.1 times BW at a treadmill speed of 4.5 mph (2.01 m/s) and a pressure setting of 100% BW to 0.8 times BW at 1.5 mph (0.67 m/s) and a pressure setting of 25% BW. Peak knee forces were significantly correlated with walking speed and treadmill reaction force (R(2) = 0.77, p = 0.04). The LBPP treadmill might be an effective tool in the rehabilitation of patients following lower-extremity surgery. The strong correlation between tibiofemoral force and walking speed and treadmill reaction forces allows for more precisely achieving the target knee forces desired during early rehabilitation.

Loading of the Knee Joint During Ergometer Cycling: Telemetric In Vivo Data

Within-subject, repeated-measures design. To measure tibiofemoral contact forces during cycling in vivo and to quantify the influences of power, pedaling cadence, and seat height on tibiofemoral contact forces. Cycling is usually classified as a low-demand activity for the knee joint and is therefore recommended for persons with osteoarthritis and rehabilitation programs following knee surgery. However, there are limited data regarding actual joint loading. Instrumented knee implants with telemetric data transmission were used to measure the tibiofemoral contact forces. Data were obtained in 9 subjects, during ergometer cycling and walking, 15 ± 7 months after total knee arthroplasty. Tibiofemoral forces during cycling at power levels between 25 and 120 W, cadences of 40 and 60 rpm, and 2 seat heights were investigated. Within the examined power range, tibiofemoral forces during cycling were smaller than those during walking. At the moderate condition of 60 W and 40 rpm, peak resultant forces of 119% of body weight were measured during the pedal downstroke. Shear forces ranged from 5% to 7% of body weight. Forces increased linearly with cycling power. Higher cadences led to smaller forces. A lower seat height did not increase the resultant force but caused higher posterior shear forces. Due to the relatively small tibiofemoral forces, cycling with moderate power levels is suited for individuals with osteoarthritis and rehabilitation programs following knee surgery, such as cartilage repair or total knee replacement. The lowest forces can be expected while cycling at a low power level, a high cadence, and a high seat height.

Paper 217: Posterior Stabilized TKA's are Less Sensitive to Implantation Tightness than PCL-Retaining Designs: A Biomechanical Study

Restricted range of motion or excessive laxity are potential complications of total knee arthroplasty (TKA). In contrast patients demand more function for daily activities. To achieve a good function after TKA is important but the aim for all patients should be a better flexion to kneel, work and live without restrictions. Hence the present study was to investigate the effects of implantation tightness on soft tissue strain during passive range of motion. Fourteen fresh frozen cadaver knee joints mounted in a passive flexion rig. Passive flexion was applied to the tibia in 15 deg increments from 0 to 150 deg of flexion. Tibiofemoral force and ligament strain of the medial and lateral collateral ligaments were measured using a custom-built force platform inserted beneath the polyethylene inlay. The standard implantation technique and two variations (2 mm tighter, 2 mm looser) were tested for four prosthesis types: fixed-bearing PCL-retaining (with and without PCL) (PFC), mobile-bearing PCL-sacrificing (LCS), posterior-stabilised (PS), posterior-stabilised with HiFlex femoral component (HF). As expected all prostheses showed a significant increase in tibiofemoral force at full extension when implantation tightness was increased. By comparison in the midrange between 15-90 deg the tibiofemoral force dropped down and was independent of variation in implantation tightness in all designs. Beyond 90 deg the fixed bearing design (PFC) and in the LCS knee were sensitive on implantation tightness. In contrast the two posterior stabilised prosthesis types (PS and HF) showed a different pattern of tibiofemoral force during flexion, with low force throughout the range of motion. As a result in full extension and deep flexion both the PFC prosthesis and the LCS knee represent sensitive designs when considering implantation tightness. Whereas posterior stabilised knee implants are associated with lower tibiofemoral force during the range of motion and more forgiving designs in relation to implantation tightness. The data also suggest that soft tissue structures other than the collaterals tighten as the knee flexes and cause an increase in tibiofemoral compressive force.