Ti-based Surface Research Articles

Biochemical Characterization of the Cell-Biomaterial Interface by Quantitative Proteomics

Surface topography and texture of cell culture substrata can affect the differentiation and growth of adherent cells. The biochemical basis of the transduction of the physical and mechanical signals to cellular responses is not well understood. The lack of a systematic characterization of cell-biomaterial interaction is the major bottleneck. This study demonstrated the use of a novel subcellular fractionation method combined with quantitative MS-based proteomics to enable the robust and high-throughput analysis of proteins at the adherence interface of Madin-Darby canine kidney cells. This method revealed the enrichment of extracellular matrix proteins and membrane and stress fibers proteins at the adherence surface, whereas it shows depletion of extracellular matrix belonging to the cytoplasmic, nucleus, and lateral and apical membranes. The asymmetric distribution of proteins between apical and adherence sides was also profiled. Apart from classical proteins with clear involvement in cell-material interactions, proteins previously not known to be involved in cell attachment were also discovered.

New degradation mechanism of Ti/IrO 2 + MnO 2 anode for oxygen evolution in 0.5 M H 2SO 4 solution

Degradation mechanism of Ti/IrO 2(0.7) + MnO 2(0.3) anode for oxygen evolution was studied in 0.5 M H 2SO 4 solution by field emission scanning electron microscopes (FESEM), Tafel slope, X-ray diffraction (XRD) and electrochemical impedance spectroscopic (EIS). The whole surface of the non-electrolyzed Ti/IrO 2(0.7) + MnO 2(0.3) anode consisted of nano-IrO 2 poles array. The anode surface had hardly discovered cracks and had compact morphology that can prevent the electrolyte from entering the Ti/oxide interface and an insulating TiO 2 film from growing on the Ti-based surface. An insulating TiO 2 phase had not been generated on the Ti/oxide interface during the process of O 2 evolution and the inactive anode surface still remained mass of the IrO 2 and MnO 2 oxides. The chemical dissolution of Ti/IrO 2(0.7) + MnO 2(0.3) anode coating was not the main reason for electrode degradation in 0.5 M H 2SO 4 solution. The degradation mechanism of Ti/IrO 2(0.7) + MnO 2(0.3) anode differed from other conventional oxide electrodes for O 2 evolution in acid medium. The platforms of Tafel slope and anode potential (900–1050 h) indicated that the change of the oxygen evolution reaction (OER) mechanism was the main reason for degradation of Ti/IrO 2(0.7) + MnO 2(0.3) anode due to the change of adsorption intermediate.

Nature of adsorption on TiC(111) investigated with density-functional calculations

Extensive density-functional calculations are performed for chemisorption of atoms in the three first periods (H, B, C, N, O, F, Al, Si, P, S, and Cl) on the polar TiC(111) surface. Calculations are also performed for O on TiC(001), for full O(1x1) monolayer on TiC(111), as well as for bulk TiC and for the clean TiC(111) and (001) surfaces. Detailed results concerning atomic structures, energetics, and electronic structures are presented. For the bulk and the clean surfaces, previous results are confirmed. In addition, detailed results are given on the presence of C-C bonds in the bulk and at the surface, as well as on the presence of a Ti-based surface resonance (TiSR) at the Fermi level and of C-based surface resonances (CSR's) in the lower part of the surface upper valence band. For the adsorption, adsorption energies E-ads and relaxed geometries are presented, showing great variations characterized by pyramid-shaped E-ads trends within each period. An extraordinarily strong chemisorption is found for the O atom, 8.8 eV/adatom. On the basis of the calculated electronic structures, a concerted-coupling model for the chemisorption is proposed, in which two different types of adatom-substrate interactions work together to provide the obtained strong chemisorption: (i) adatom-TiSR and (ii) adatom-CSR's. This model is used to successfully describe the essential features of the calculated E-ads trends. The fundamental nature of this model, based on the Newns-Anderson model, should make it apt for general application to transition-metal carbides and nitrides and for predictive purposes in technological applications, such as cutting-tool multilayer coatings and MAX phases.

Correlation of microstructure with the hardness and wear resistance of (TiC,SiC)/Ti-6Al-4V surface composites fabricated by high-energy electron-beam irradiation

The correlation of microstructure with the hardness and wear resistance of (TiC,SiC)/Ti-6Al-4V surface composites fabricated by high-energy electron-beam irradiation was investigated in this study. The mixtures of TiC, SiC, or TiC + SiC powders and CaF2 flux were placed on a Ti-6Al-4V substrate, and then an electron beam was irradiated on these mixtures using an electron-beam accelerator. The surface composite layers of 1.2 to 2.1 mm in thickness were formed without defects and contained a large amount (up to 66 vol pct) of precipitates such as TiC and Ti5Si3 in the martensitic matrix. This microstructural modification, including the formation of hard precipitates and a hardened matrix in the surface composite layer, improved the hardness and wear resistance. Particularly in the surface composite fabricated with TiC + SiC powders, the wear resistance was greatly enhanced to a level 25 times higher than that of the Ti alloy substrate, because 66 vol pct of TiC and Ti5Si3 was precipitated homogeneously in the hardened martensitic matrix. These findings suggested that high-energy electron-beam irradiation was useful for the development of Ti-based surface composites with improved hardness and wear properties.

Correlation of microstructure and abrasive and sliding wear resistance of (TiC,SiC)/Ti-6Al-4V surface composites fabricated by high-energy electron-beam irradiation

This study is concerned with the correlation of microstructure and abrasive and sliding wear resistance of (TiC,SiC)/Ti-6Al-4V surface composites fabricated by high-energy electron-beam irradiation. The mixtures of TiC, SiC, Ti + SiC, or TiC+SiC powders and CaF2 flux were deposited on a Ti-6Al-4V substrate, and then an electron beam was irradiated on these mixtures. The surface composite layers of 1.2 to 2.1 mm in thickness were homogeneously formed without defects and contained a large amount (30 to 66 vol pct) of hard precipitates such as TiC and Ti5Si3 in the martensitic matrix. This microstructural modification, including the formation of hard precipitates in the surface composite layer, improved the hardness and abrasive wear resistance. Particularly in the surface composite fabricated with TiC + SiC powders, the abrasive wear resistance was greatly enhanced to a level 25 times higher than that of the Ti alloy substrate because of the precipitation of 66 vol pct of TiC and Ti5Si3 in the hardened martensitic matrix. During the sliding wear process, hard and coarse TiC and Ti5Si3 precipitates fell off from the matrix, and their wear debris worked as abrasive particles, thereby reducing the sliding wear resistance. On the other hand, needle-shaped Ti5Si3 particles, which did not play a significant role in enhancing abrasive wear resistance, lowered the friction coefficient and, accordingly, decelerated the sliding wear, because they played more of the role of solid lubricants than as abrasive particles after they fell off from the matrix. These findings indicated that high-energy electron-beam irradiation was useful for the development of Ti-based surface composites with improved abrasive and sliding wear resistance, although the abrasive and sliding-wear data should be interpreted by different wear mechanisms.

Testing biomaterials by the in-situ evaluation of cell response

In this work, we describe a technique for the in-situ observation of cells adhered on opaque biomaterial surfaces. The visualisation of the morphology of cells adhered onto a surface allows to derive nuclear apoptotic signs or even the existence of organisation between groups of these cells. The technique is based on the use of an auto-immune reaction combined with a fluorescent agent that allows a direct inspection of the cell behaviour. The versatility of the technique is demonstrated by presenting several examples with different cultured cells (human chondrosarcome cells (CSRCs) and pluripotential mesenchymal stem cells (MSCs) from bone marrow) seeded over two different Ti-based surfaces (TiO 2 and TiN, respectively). These in-vitro observations are compared with the behaviour of the same cells on bare TiAlV alloy. From our results it is concluded that both TiO 2 and TiN surfaces show enhanced biological responses.

Improvement in the morphology of Ti-based surfaces: a new process to increase in vitro human osteoblast response

Surface roughness has been shown to be an influencing parameter for cell response. In this experience we attempted to compare the effect of roughness organization of Ti6Al4V or pure titanium substrates on human osteoblast (hOB) response (proliferation, adhesion). Surface roughness was extensively analyzed at scales above the cell size (macro-roughness) or below the cell size (micro-roughness) by calculation of relevant classic amplitude parameters (Ra, Rt) and original frequency parameters (Order, Delta). We developed a new process to prepare isotropic surfaces (electro-erosion), which were compared to isotropic surfaces obtained by polishing and anisotropic surfaces obtained by machine-tooling. The hOB response on electro-eroded (EE) Ti6Al4V surfaces or pure titanium (Ti) surfaces was largely increased when compared to polished or machine-tooled surfaces after 21 days of culture. Moreover, the polygonal morphology of hOB on these EE surfaces was very close to the aspects of hOB in vivo on human bone trabeculae. By a complete description of the surface topography of EE surfaces, we concluded that when the topography was considered below the cell scale, hOB appreciated their isotropic smooth aspect, although when the topography was considered above the cell scale they appreciated their rough isotropic ‘landscape’ formed by many ‘bowl-like nests’ favouring cell adhesion and growth. Electro-erosion is a promising method for preparation of bone implant surfaces, as it could easily be applied to preparation of most biomaterials with complex geometries.