Thin-disk Regenerative Amplifier Research Articles

High-efficiency Yb:YAG thin-disk chirped pulse amplifier delivering 884-femtosecond laser with tunable repetition rates and high stability

We experimentally demonstrated a compact, highly efficient, stable, chirped pulse amplification (CPA) thin-disk regenerative system with a tunable repetition rate. The laser head consists of a 9 at. % Yb:YAG thin-disk with a diameter of 8.8 mm and a thickness of 150 μm, is designed for a 48-pump pass configuration. In CPA-based regenerative amplifier configuration, a maximal output power of 85 W at 500 kHz is achieved with a conversion efficiency of 53.1 %. This corresponds to a pulse energy of 170 μJ. To the best of our knowledge, this is the highest conversion efficiency in CPA thin-disk regenerative amplifiers. The pulse width is compressed to 884 fs with a pair of grating, resulting in a peak power of 192 MW. At 85 W, a near diffraction limit beam quality factor M2 of 1.40 is measured, which is essential in precision applications. In addition, remarkable long-term power stability is confirmed with a root-mean-square (RMS) fluctuation of 0.12 % over a 24-hour duration. The reported femtosecond amplifier is believed to be a promising tool for various applications such as extreme manufacturing, terahertz spectroscopy, etc.

Cpa-free Yb:YAG thin-disk regenerative amplifier laser with hundreds of watts, hundreds of kHz, and hundreds of picoseconds

This paper introduces a CPA-free Yb:YAG thin-disk regenerative amplifier laser system. The seed pulse is generated by a passive mode-locked picosecond oscillator based on a semiconductor saturable absorber mirror, with a center wavelength of 1030.7 nm, a pulse width of 7.7 ps, and a repetition frequency of 26.3 MHz. After stretched and pre-amplified by an all-fiber front stage, the seed with a pulse width of 201.3 ps and a pulse energy of 15.2 nJ was obtained, then injected into the thin-disk regenerative amplifier. Yb:YAG crystal was chosen as the material for the thin-disk, with 100 μm thickness, 9 mm diameter and 7 at.% doping rate. In order to increase the one-way round-trip gain of the thin-disk regenerative amplifier, a symmetrical dual-pass resonant cavity was designed to double the number of passing through the crystal on a round trip in the regenerative resonant cavity to reduce the times of cycles, intra-cavity loss and improve optical efficiency. We used a 969 nm fiber-coupled semiconductor laser as the pump source to pump the Yb:YAG thin-disk crystal. With zero-phonon line pumping technology, the quantum loss and thermal effect were reduced. In the end, we obtained a regenerative amplification output with an average power of 104.5 W, a repetition frequency of 200 kHz, a pulse width of 143.9 ps, and a spectrum width of 0.39 nm. The amplified pulse had quite good beam quality with Mx2 = 1.09 and My2 = 1.14.

Compact 56 mJ thin-disk regenerative amplifier with thermally-near-unstable resonator structure

We experimentally demonstrated a very compact Yb:YAG thin-disk regenerative amplifier with hundred millijoules output potential. The cavity was designed based on the thermal-near-unsteady resonator concept with a cavity length of only 2 m. Laser outputs of 205 W for continuous wave, 156 W (3.1 mJ) for pulsed waves at 50 kHz, and 56 W (56 mJ) for pulsed waves at 1 kHz were achieved. To the best of our knowledge, this is the shortest cavity length reported for a thin-disk regenerative amplifier with a thermally-nearly-unstable resonator and the first time a pulsed-wave output has been achieved. This compact hundred-millijoule-class thin-disk regenerative amplifier allows for a significant simplification of the resonator structure and thus improves the environmental suitability of the system.

Yb∶YAG Single Thin-Disk Regenerative Amplifier with High Stability and High Optical-to-Optical Efficiency

Yb∶YAG Single Thin-Disk Regenerative Amplifier with High Stability and High Optical-to-Optical Efficiency

High-repetition-rate and High-power Efficient Picosecond Thin-disk Regenerative Amplifier

High-repetition-rate and High-power Efficient Picosecond Thin-disk Regenerative Amplifier

Beam mutation and its suppression in Yb:YAG thin-disk regenerative amplifiers

Beam mutation in thin-disk regenerative amplifiers is proposed here, to the best of our knowledge, for the first time. It is proved to appear together with period doubling bifurcation and deterministic chaos experimentally. The suppression of beam mutation is achieved by reducing the gate length of the regenerative amplifier. With the gate length of 1.88 μs, a Yb:YAG thin-disk regenerative amplifier with stable beam and single-energy pulse is realized. The maximum pulse energy is 145 mJ with the optical-optical efficiency of around 10 %. The repetition rate and the pulse width are 1 kHz and 580 ps respectively.

Importance of crystal length on the stability of a picosecond supercontinuum generated in undoped YAG

In this paper, we present the stability characteristics of a supercontinuum (SC) generated in a 60 mm, 100 mm, and 130 mm long undoped yttrium aluminum garnet (YAG) crystal pumped by a Yb thin-disk regenerative amplifier. The 1.2 ps pulses with a central wavelength of 1030 nm and repetition rate of 89 kHz are loosely focused (NA = 0.0031) into the crystal in order to prevent laser-induced damage and to increase the energy stability of the generated SC. Out of the tested crystal lengths, the optimal is experimentally determined to be 130 mm. The energy contained in the blueshifted side, which has a 530 nm spectral cutoff, is 71 nJ and exhibits average power stability of 0.4% RMS, which is 2.5× better than the stability of the pump beam.

120 mJ, 1 kHz, picosecond laser at 515 nm.

We report on a 1 kHz, 515 nm laser system, based on a commercially available 230 W average power Yb:YAG thin-disk regenerative amplifier, developed for pumping one of the last optical parametric chirped pulse amplification (OPCPA) stages of the Allegra laser system at ELI Beamlines. To avoid problems with self-focusing of picosecond pulses, the 1030 nm output pulses are compressed and frequency doubled with an LBO crystal in vacuum. Additionally, development of a thermal management system was needed to ensure stable phase matching conditions at high average power. The resulting 515 nm pulses have an energy of more than 120 mJ with SHG efficiency of 60% and an average RMS stability of 1.1% for more than 8 h.

Numerical and Experimental Analysis of Yb:YAG Thin Disk Regenerative Amplifier

We present an numerical and experimental analysis of a Yb:YAG thin disk regenerative amplifier. Group velocity dispersion, third order dispersion, and self-phase modulation (SPM) effects are considered in the simulations of the amplification process. By virtue of the simulations, a compact femtosecond Yb:YAG thin-disk chirped-pulse regenerative amplifier delivering an average power of 50 W at a central wavelength of 1030 nm with a propagation factor of M <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> <; 1.4 at a repetition rate of 200 kHz and a pulse duration of 500 fs was constructed. Numerical simulation based on this Yb:YAG thin-disk was carried out to investigate the pulse parameters evolution in each round trip. The measured experimental results in pulse width, spectrum, and pulse energy together fitted quite well with the numerical simulation. This plays an important role in the design of high-peak-power regenerative amplifier and will facilitate further power scaling and suppression of gain narrowing of the whole system.

Study on X-ray enhancement in Laser-Compton scattering for auger therapy

Purpose Monochromatic hard X-rays with high brightness are desired for medical applications including Auger therapy. One can generate such X-rays through laser-Compton scattering (LCS) by allowing photons from a compact laser system to interact with electrons accelerated by a compact electron accelerator. In this paper, after a brief description of laser-Compton X-ray sources, a scheme called crab crossing to enhance the X-ray intensity is proposed. The effect of crab crossing is evaluated, and we report our dedicated laser system for the crab crossing LCS research. Materials and methods The luminosity enhancement factor by crab crossing is evaluated. For the electron beam, a rf deflector will be used to generate a tilted electron beam. For the laser system, chirped pulsed amplification is adopted. Yb-doped optical fibers and a Yb:YAG thin-disk is used for the laser gain media. Results The luminosity enhancement factor by crab crossing is expected to be 3.8 when the crossing angle is 45 degrees. 10mJ pulse energy was achieved by thin-disk regenerative amplifier. The pulse duration after the pulse compressor was about 1.5 ps. Conclusion We are going to demonstrate the LCS X-ray enhancement by crab crossing of electron beam and laser pulse. The expected enhancement factor is 3.8. We have successfully finished the laser development and the proof-of-principle experiment will be conducted soon.

Robust method for long-term energy and pointing stabilization of high energy, high average power solid state lasers.

A robust and simple method is presented for ensuring constant energy and pointing of a high average power solid state laser on a target. In addition to providing long-term stability, this scheme also eliminates any drifts in energy or pointing resulting from the initial warm-up after a cold start. This is achieved using two separate feedback loops: one loop stabilizes the pointing of the beam external to the amplifier cavity and the other locks the cavity mode to have optimum overlap with the pump spot on the active medium. The key idea of the cavity mode stabilization is to monitor the overlap of the cavity mode and the gain medium with a camera and control it with an actively controlled, intra-cavity mirror. While this method is demonstrated on a thin-disk regenerative amplifier, it can also be applied to a wide variety of solid state laser amplifiers.

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier

This is a report on a 100 W, 20 mJ, 1 ps Yb:YAG thin-disk regenerative amplifier. A homemade Yb:YAG thin-disk, Kerr-lens mode-locked oscillator with turn-key performance and microjoule-level pulse energy is used to seed the regenerative chirped-pulse amplifier. The amplifier is placed in airtight housing. It operates at room temperature and exhibits stable operation at a 5 kHz repetition rate, with a pulse-to-pulse stability less than 1%. By employing a 1.5 mm-thick beta barium borate crystal, the frequency of the laser output is doubled to 515 nm, with an average power of 70 W, which corresponds to an optical-to-optical efficiency of 70%. This superior performance makes the system an attractive pump source for optical parametric chirped-pulse amplifiers in the near-infrared and mid-infrared spectral range. Combining the turn-key performance and the superior stability of the regenerative amplifier, the system facilitates the generation of a broadband, CEP-stable seed. Providing the seed and pump of the optical parametric chirped-pulse amplification (OPCPA) from one laser source eliminates the demand of active temporal synchronization between these pulses. This work presents a detailed guide to set up and operate a Yb:YAG thin-disk regenerative amplifier, based on chirped-pulse amplification (CPA), as a pump source for an optical parametric chirped-pulse amplifier.

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier.

This is a report on a 100 W, 20 mJ, 1 ps Yb:YAG thin-disk regenerative amplifier. A homemade Yb:YAG thin-disk, Kerr-lens mode-locked oscillator with turn-key performance and microjoule-level pulse energy is used to seed the regenerative chirped-pulse amplifier. The amplifier is placed in airtight housing. It operates at room temperature and exhibits stable operation at a 5 kHz repetition rate, with a pulse-to-pulse stability less than 1%. By employing a 1.5 mm-thick beta barium borate crystal, the frequency of the laser output is doubled to 515 nm, with an average power of 70 W, which corresponds to an optical-to-optical efficiency of 70%. This superior performance makes the system an attractive pump source for optical parametric chirped-pulse amplifiers in the near-infrared and mid-infrared spectral range. Combining the turn-key performance and the superior stability of the regenerative amplifier, the system facilitates the generation of a broadband, CEP-stable seed. Providing the seed and pump of the optical parametric chirped-pulse amplification (OPCPA) from one laser source eliminates the demand of active temporal synchronization between these pulses. This work presents a detailed guide to set up and operate a Yb:YAG thin-disk regenerative amplifier, based on chirped-pulse amplification (CPA), as a pump source for an optical parametric chirped-pulse amplifier.

Generation of high-energy femtosecond pulses by use of spectral broadening effects in Yb:YAG thin-disk regenerative amplifiers

As a result of experimentally verified simulations of Yb:YAG regenerative amplifiers utilizing spectral broadening effects due to self-phase modulation, we provide a map for the optimized choice of initial chirp and internal group-delay dispersion (GDD) within the amplifier. We show that the shortest pulse durations can be obtained with negative internal GDD, being, however, limited by the damage threshold of the optical components due to increased peak powers and by a breakup of pulses comparable to the propagation of higher-order solitons. We propose that by usage of increasing amounts of positive internal GDD, along with a corresponding amount of negative initial GDD, the obtainable peak powers after compression can be scaled far beyond the usual gain-bandwidth limitation.

4-W, 100-kHz, few-cycle mid-infrared source with sub-100-mrad carrier-envelope phase noise.

We demonstrate an optical parametric chirped-pulse amplifier delivering 4-cycles (38-fs) pulses centered around 3.1 µm at 100-kHz repetition rate with an average power of 4 W and an undersampled single-shot carrier-envelope phase noise of 81 mrad recorded over 25 min. The amplifier is pumped by a ~1.1 ps, Yb-YAG, thin-disk regenerative amplifier and seeded with a supercontinuum generated in bulk YAG from the same pump pulses. Carrier-envelope phase stability is passively achieved through difference-frequency generation between pump and seed pulses. An additional active stabilization at 10 kHz combining 2f-to-f interferometry and a LiNbO3 acousto-optic programmable dispersive filter achieves a record low phase noise.

Direct regenerative amplification of femtosecond pulses to the multimillijoule level.

We present a compact femtosecond nonlinear Yb:YAG thin-disk regenerative amplifier delivering pulses carried at a wavelength of 1030nm with an average power of >200 W at a repetition rate of 100kHz and an energy noise value of 0.46% (rms) in a beam with a propagation factor of M2<1.4. The amplifier is seeded with bandwidth-limited subpicosecond pulses without temporal stretching. We give estimates for the nonlinear parameters influencing the system and show that chirped mirrors compress the 2mJ pulses to a near-bandwidth-limited duration of 210fs.

Self-compressed, spectral broadening of a Yb:YAG thin-disk amplifier.

We demonstrate pulse shortening of 1-ps Yb:YAG thin-disk regenerative amplifier to 500 fs by cross-polarized wave generation (XPW) in a 6 mm BaF2 crystal. The process is self-compressed and has 8.5% conversion efficiency corresponding to 18 µJ energy. Our theoretical and experimental investigation shows that the factor of 3 spectral broadening and pulse shortening in ps-XPW-generation only happens in unsaturated regime. We demonstrate that the initial spectral chirp affects the spectral broadening and pulse shortening of XPW pulses.

High-power, 1-ps, all-Yb:YAG thin-disk regenerative amplifier.

We report a 100 W, 20 mJ, 1-ps, all-Yb:YAG thin-disk regenerative amplifier seeded by a microjoule-level Yb:YAG thin-disk Kerr-lens mode-locked oscillator. The regenerative amplifier is implemented in a chirped pulse amplification system and operates at an ambient temperature in air, delivering ultrastable output pulses at a 5 kHz repetition rate and with a root mean square power noise value of less than 0.5%. Second harmonic generation of the amplifier's output in a 1.5 mm-thick BBO crystal results in more than 70 W at 515 nm, making the system an attractive source for pumping optical parametric chirped pulse amplifiers in the visible and near-infrared spectral ranges.

Thin disk amplifier-based 40 mJ, 1 kHz, picosecond laser at 515 nm.

We report on a frequency-doubled picosecond Yb:YAG thin disk regenerative amplifier, developed as a pump laser for a kilohertz repetition rate OPCPA. At a repetition rate of 1 kHz, the compressed output of the regenerative amplifier has a pulse duration of 1.2 ps and pulse energy of 90 mJ with energy stability of σ < 0.8% and M2 < 1.2. The pulses are frequency doubled in an LBO crystal yielding 42 mJ at 515 nm.

Yb:YAG thin-disk chirped pulse amplification laser system for intense terahertz pulse generation.

We have developed a 1 kHz repetition picosecond laser system dedicated for intense terahertz (THz) pulse generation. The system comprises a chirped pulse amplification laser equipped with a Yb:YAG thin-disk amplifier. At room temperature, the Yb:YAG thin-disk regenerative amplifier provides pulses having energy of over 10 mJ and spectral bandwidth of 1.2 nm. The pulse duration achieved after passage through a diffraction grating pair compressor was 1.3 ps. By employing this picosecond laser as a pump source, THz pulses having a peak frequency of 0.3 THz and 4 µJ of energy were generated by means of optical rectification in an Mg-doped LiNbO3 crystal.