Cell Wall Thickness Research Articles

Mechanical properties of a novel negative Poisson's ratio gradient structure

A novel cellular structure is proposed based on bionic structure with negative Poisson's ratio characteristic, and the cell is periodically expanded in the in-plane direction to create a new honeycomb structure. The influence of gradient changes of the structural parameters on the load-bearing capacity and damping characteristics of the structure is investigated through a combination method of finite element numerical simulations and experiments. The results indicate that the concentric gradient arrangement of cell wall thickness and angle parameters, and the symmetrical gradient arrangement of cell height, wall thickness and angle parameters have the most significant influence on the static bearing capacity of the structure. In contrast, the gradient arrangement under the corner circle diameter has minimal effect on the static bearing capacity of the structure. Under the same conditions, the peak values of the transmissibility of C2 (large angle at constraint end and loading end, and smaller angle in the middle) and C3 structures (angle gradually increases from the loading end to the constraint end) are significantly reduced between the frequency 2 Hz and 1024 Hz. The peak values of the transmissibility of the structures C2 and C3 are respectively decreased by 20% and 25% compared to that of the non-gradient structure. This shows that the vibration damping effect of these two structures is better. The structure with the gradient change and the structure without the gradient change of the new honeycomb structure can both achieve certain vibration reduction and isolation from the middle to high frequency range.

Staphylococcus aureus Stress Response to Bicarbonate Depletion.

Bicarbonate and CO2 are essential substrates for carboxylation reactions in bacterial central metabolism. In Staphylococcus aureus, the bicarbonate transporter, MpsABC (membrane potential-generating system) is the only carbon concentrating system. An mpsABC deletion mutant can hardly grow in ambient air. In this study, we investigated the changes that occur in S. aureus when it suffers from CO2/bicarbonate deficiency. Electron microscopy revealed that ΔmpsABC has a twofold thicker cell wall thickness compared to the parent strain. The mutant was also substantially inert to cell lysis induced by lysostaphin and the non-ionic surfactant Triton X-100. Mass spectrometry analysis of muropeptides revealed the incorporation of alanine into the pentaglycine interpeptide bridge, which explains the mutant's lysostaphin resistance. Flow cytometry analysis of wall teichoic acid (WTA) glycosylation patterns revealed a significantly lower α-glycosylated and higher ß-glycosylated WTA, explaining the mutant's increased resistance towards Triton X-100. Comparative transcriptome analysis showed altered gene expression profiles. Autolysin-encoding genes such as sceD, a lytic transglycosylase encoding gene, were upregulated, like in vancomycin-intermediate S. aureus mutants (VISA). Genes related to cell wall-anchored proteins, secreted proteins, transporters, and toxins were downregulated. Overall, we demonstrate that bicarbonate deficiency is a stress response that causes changes in cell wall composition and global gene expression resulting in increased resilience to cell wall lytic enzymes and detergents.

Effects of foliar treatments with urea and nano-urea on the cell walls of Monastrell grape skins

Cell wall composition can be affected by nitrogen availability in the vineyard. Foliar application of urea is effective in supplying nitrogen needs and increasing the nitrogen content of musts. Due to the low recoveries of urea fertilisation, more effective application methods such as the use of nanotechnology are needed. In this work, the effect on the composition of Monastrell grape skin cell walls, after foliar application of urea and amorphous calcium phosphate nano-particles doped with urea was studied. The treatments with urea and nano-urea, although the urea content in the nano-treatment was eight times lower than in the conventional treatment, produce an equivalent modification of the cell wall. In fact, both treatments produced an increase in cell wall thickness and in cell wall composition, contents of proteins, hemicellulose and uronic acids also increased. However, phenolic compounds were not affected and cellulose showed lower concentrations than control grapes. Regarding the spectrophotometric parameters of the wine studied, the anthocyanins content and colour intensity were reduced in wines with both treatments and the total polyphenol index was slightly affected.

Nonlinear models based on leaf architecture traits explain the variability of mesophyll conductance across plant species.

Mesophyll conductance ( ) describes the efficiency with which moves from substomatal cavities to chloroplasts. Despite the stipulated importance of leaf architecture in affecting , there remains a considerable ambiguity about how and whether leaf anatomy influences . Here, we employed nonlinear machine-learning models to assess the relationship between 10 leaf architecture traits and . These models used leaf architecture traits as predictors and achieved excellent predictability of . Dissection of the importance of leaf architecture traits in the models indicated that cell wall thickness and chloroplast area exposed to internal airspace have a large impact on interspecific variation in . Additionally, other leaf architecture traits, such asleaf thickness, leaf densityand chloroplast thickness, emerged as important predictors of . We also found significant differences in the predictability between models trained on different plant functional types. Therefore, by moving beyond simple linear and exponential models, our analyses demonstrated that a larger suite of leaf architecture traits drive differences in than has been previously acknowledged. These findings pave the way for modulating by strategies that modify its leaf architecture determinants.

Biochar and soil contributions to crop lodging and yield performance - A meta-analysis

Applying biochar has beneficial effects on regulating plant growth by providing water and nutrient availability for plants due to its physicochemical characteristics. Nevertheless, it is still unclear how soil and biochar interactions strengthen crop lodging resistance. The objective of the current study was to find out how soil physicochemical conditions and alterations in biochar affect lodging resistance and crop productivity in cereals. To do this, a meta-analysis was carried out using nine groups of effective variables including type of feedstock, pyrolysis temperature, application rate, soil pH, total nitrogen, available phosphorus, potassium, organic matter (OM), and soil texture. Results showed that straw-derived biochar caused the highest positive effect size in the dry weight of biomass (20.5%) and grain yield (19.9%). Also, the lowest lodging index was observed from straw (−8.3%) and wood-based (−5.6%) biochars. Besides, the high application rate of biochar results in the highest positive effect sizes of plant cellulose (8.1%) and lignin content (7.6%). Soils that contain >20 g kg−1 OM, resulted in the highest positive effect size in dry biomass (27.9%), grain yield (30.2%), and plant height (4.7%). Also, fine-textured soil plays an important role in increasing polymers in the anatomical structure of plants. Overall, the strong connection between biochar and soil processes, particularly the availability of OM, could strengthen plants' ability to tolerate lodging stress and contribute to high nutrient efficiency in terms of crop output and cell wall thickening.

The structural organization of the outer tissues in the gametophytic stem of the umbrella moss Hypnodendron menziesii optimizes load bearing.

The ultrastructural design and biochemical organization of the significantly thickened outer tissues of the gametophytic stem of Hypnodendron menziesii optimizes load bearing of the stem. Hypnodendron menziesii is a bryoid umbrella moss growing in high humid conditions on the forest floors of New Zealand. The erect gametophyte bears up to eight whorls of branches in succession, spreading across the stem that bears the heavy weight of branches with highly hydrated leaves. Our investigation using a combination of light microscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM), and TEM-immunolabeling techniques provided novel information on the structural design and biochemical organization of greatly thickened cell walls of epidermal, hypodermal, and outermost cortical tissues, comparing underlying thin-walled cortical tissues in the gametophytic stem. Probing into the ultrastructure of the cell wall architecture of these target tissues by TEM and SEM revealed the cell walls to display a multilamellar organization, in addition to demonstrating the presence of an electron-dense substance in the cell wall, presumably flavonoids. The pattern of distribution and concentration of rhamnogalacturonan, homogalacturonan, and heteromannan, as determined by immunogold labeling, suggests that it is the combination of structural and molecular design of the cell wall that may optimize the mechanical function of the epidermal, hypodermal, and outer cortical tissues. Statistical relationships between the overall thickness of epidermal, hypodermal, and outer cortical cell walls, the lumen area of cells and the percentage area of cell wall occupied in these tissues at different heights of the stem, and thickness of secondary cell wall layers (L1-L4/5) were explored. The results of these analyses unequivocally support the contribution of outer tissues to the mechanical strength of the resilient stem.

Assessing the effects of mechanical damage on optical properties of strawberries in the 950−1650 nm range

To investigate the effect mechanism of early damage on optical properties of strawberries, the optical parameters, internal qualities and microstructure parameters of bruised samples and intact ones were acquired and quantitatively analyzed. The results showed that the soluble solids content increased with damage time, while the moisture content decreased. Firmness showed no difference between intact and bruised samples. The cell circularity (Cc) initially decreased, then slightly increased over damage time. The average cell diameter (Davg) increased with longer damage durations, and the average values of cell wall thickness (Tcw) decreased with longer damage durations. The absorption coefficient (µα) values of bruised samples were higher than the intact ones at 970 nm and 1190 nm. For reduced scattering coefficient (µ′s), at 970 nm and 1190 nm, differences were observed between intact strawberries and bruised samples subjected to three different durations of damage. The average R values of µ′s with Cc, Tcw and Davg were 0.79, 0.93 and −0.93, respectively, confirming a strong correlation of µ′s with cell diameter and cell wall thickness. The support vector machine classification model built based on µα spectra had better performance than that based on µ′s spectra, and the model based on combinations of µα and µ′s (µeff) exhibited the highest accuracy for both the calibration set and prediction set with accuracies of 96.00 % and 92.19 %, respectively. The study provides a theoretical basis for detecting latent damaged strawberries based on optical properties.

A gyroid TPMS heat sink for electronic cooling

The trend toward thinner and lighter electronic devices necessitates developing advanced thermal management solutions to address modern microprocessors’ escalating heat dissipation demands. This study introduces an advanced thermal solution incorporating a gyroid TPMS structure with remarkable physical properties for microprocessor cooling. Detailed investigations were conducted using a full-scale heat sink model to understand the inner geometric structure, flow, and heat transfer characteristics within a gyroid heat sink (GHS). The thermo-hydraulic performance of the GHS design was systematically assessed against that of a pinfin heat sink (PHS) across different porosities and flow rates. Both heat sinks were evaluated under non-uniform heating conditions, considering three heating schemes, each with eleven randomly distributed hotspots. The thermohydraulic performance was assessed by calculating temperature non-uniformity, thermal resistance, and pumping power. A correlation was established using the cell size and cell wall thickness of a unit cell of gyroid TPMS to calculate its hydraulic diameter. The analysis revealed that the enhanced thermal performance of the GHS design can be attributed to its intricate and convoluted flow structure, along with a significantly large heat transfer surface area. However, these same factors contribute to a notably high-pressure drop. Compared to the PHS design, the GHS design showed better thermal performance at all the selected porosities and flow rates, albeit with higher pumping powers. The GHS design showed improvement in the thermal performance as the porosity decreased. Investigation under heterogeneous heating conditions showed substantially lower temperatures at the hotspots in the GHS design, along with reduced temperature variation among them. The study’s findings provide valuable insight into the advantages and drawbacks of gyroid TPMS structure for their application in electronic cooling.

Host-induced cell wall remodeling impairs opsonophagocytosis of Staphylococcus aureus by neutrophils.

Understanding how bacteria adapt to the host environment is critical in determining fundamental mechanisms of immune evasion, pathogenesis, and the identification of targets for new therapeutic approaches. Previous work demonstrated that Staphylococcus aureus remodels its cell envelope in response to host factors and we hypothesized that this may affect recognition by antibodies and thus killing by immune cells. As expected, incubation of S. aureus in human serum resulted in rapid binding of antibodies. However, as bacteria adapted to the serum, the increase in cell wall thickness resulted in a significant reduction in exposure of bound antibodies. This reduced antibody exposure, in turn, led to reduced killing by human neutrophils. Importantly, while antibodies bound to some cell surface structures became obscured, this was not the case for those bound to wall teichoic acid, which may have important implications for vaccine design.

Functional profiling of CHAP domain-containing peptidoglycan hydrolases of Staphylococcus aureus USA300 uncovers potential targets for anti-staphylococcal therapies

The bacterial pathogen Staphylococcus aureus employs a thick cell wall for protection against physical and chemical insults. This wall requires continuous maintenance to ensure strength and barrier integrity, but also to permit bacterial growth and division. The main cell wall component is peptidoglycan. Accordingly, the bacteria produce so-called peptidoglycan hydrolases (PGHs) that cleave glycan strands to facilitate growth, cell wall remodelling, separation of divided cells and release of exported proteins into the extracellular milieu. A special class of PGHs contains so-called ‘cysteine, histidine-dependent amidohydrolase/peptidase’ (CHAP) domains. In the present study, we profiled the roles of 11 CHAP PGHs encoded by the core genome of S. aureus USA300 LAC. Mutant strains lacking individual CHAP PGHs were analysed for growth, cell morphology, autolysis, and invasion and replication inside human lung epithelial cells. The results show that several investigated CHAP PGHs contribute to different extents to extracellular and intracellular growth and replication of S. aureus, septation of dividing cells, daughter cell separation once the division process is completed, autolysis and biofilm formation. In particular, the CHAP PGHs Sle1 and SAUSA300_2253 control intracellular staphylococcal replication and the resistance to β-lactam antibiotics like oxacillin. This makes the S. aureus PGHs in general, and the Sle1 and SAUSA300_2253 proteins in particular, attractive targets for future prophylactic or therapeutic anti-staphylococcal interventions. Alternatively, these cell surface-exposed enzymes, or particular domains of these enzymes, could be applied in innovative anti-staphylococcal therapies.

Quantitative Trait Loci Mapping and Candidate Gene Analysis for Fiber Quality Traits in Upland Cotton

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 13 major effect QTLs that contributed more than 10% toward phenotypic variation (PV) and 9 stable QTLs that could be repeatedly mapped in different generations. Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosomes D1 and D11. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18–21.45% of PV and qFS-A11-1 in F2:3, F2:4, and F2:5 with 6.05–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, while Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Reduced mesophyll conductance under chronic O3 exposure in poplar reflects thicker cell walls and increased subcellular diffusion pathway lengths according to the anatomical model.

Ozone (O3) is one of the most harmful and widespread air pollutants, affecting crop yield and plant health worldwide. There is evidence that O3 reduces the major limiting factor of photosynthesis, namely CO2 mesophyll conductance (gm), but there is little quantitative information of O3-caused changes in key leaf anatomical traits and their impact on gm. We exposed two O3-responsive clones of the economically important tree species Populus × canadensis Moench to 120 ppb O3 for 21 days. An anatomical diffusion model within the leaf was used to analyse the entire CO2 diffusion pathway from substomatal cavities to carboxylation sites and determine the importance of each structural and subcellular component as a limiting factor. gm decreased substantially under O3 and was found to be the most important limitation of photosynthesis. This decrease was mostly driven by an increased cell wall thickness and length of subcellular diffusion pathway caused by altered interchloroplast spacing and chloroplast positioning. By contrast, the prominent leaf integrative trait leaf dry mass per area was neither affected nor related to gm under O3. The observed relationship between gm and anatomy, however, was clone-dependent, suggesting that mechanisms regulating gm may differ considerably between closely related plant lines. Our results confirm the need for further studies on factors constraining gm under stress conditions.

Enhanced lignin and cellulose metabolism promote cell wall synthesis and growth of wild soybean HRA under alkali stress.

Soil salinization adversely threatens plant survival and food production globally. The mobilization of storage reserves in cotyledons and establishment of the hypocotyl/root axis (HRA) structure and function are crucial to the growth of dicotyledonous plants during the post-germination growth period. Here, we report the adaptive mechanisms of wild and cultivated soybeans in response to alkali stress in soil during the post-germination growth period. Diferences in physiological parameters, microstructure, and the types, amounts and metabolic pathways of small molecule metabolites and gene expression were compared and multi-omics integration analysis was performed between wild and cultivated soybean under sufcient and artifcially simulated alkali stress during the post-germination growth period in this study. Structural analysis showed that the cell wall thickness of wild soybean under alkali stress increased, whereas cultivated soybeans were severely damaged. A comprehensive analysis of small molecule metabolites and gene expression revealed that protein breakdown in wild soybean cotyledons under alkali stress was enhanced, and transport of amino acids and sucrose increased. Additionally, lignin and cellulose synthesis in wild soybean HRA under alkali stress were enhanced. verall, protein decomposition and transport of amino acids and sucrose increased in wild soybean cotyledons under alkali stress, which in turn, promotes HRA growth. Similarly, lignin and cellulose synthesis in wild soybean HRA enhanced, which subsequently, enhanced cell wall synthesis, thereby maintaining the stability and functionality of HRA under alkali stress. This study presents important practical implications for the utilization of wild plant resources and sustainable development of agriculture.

Anatomical characteristic and fiber morphology of fibrovascular bundle of Indonesian nipa (Nypa fruticans) frond

Nipa (Nypa Fruticans) is a palm tree that grows in wetlands and mangroves. Nipa fronds possess lignocellulose and hold the potential as a viable source for producing composite boards, pulp, and paper. This research aims to identify the anatomical and morphological characteristics of nipah fronds fiber, especially in the fibrovascular bundle. Nipa fronds were observed in the radial and longitudinal directions. There are four zones in the radial direction, consisting of the outer zone (convex and concave), middle zone, and inner zone. The longitudinal positions consist of the bottom, intermediate, and upper. Anatomical characteristics were observed using a light microscope focused on the fibrovascular bundle's characteristics. Fiber morphology was measured at each position with 20 repetitions of each measurement. The results showed that the number of FVB increased from the outer zone, especially convex towards the middle and inner zone. Thus, the outer fronds are denser than the inner zone. Based on observations of fiber morphology, the concave (radial) zone in the intermediate position (longitudinal) has the longest fiber compared to the other parts. Meanwhile, the cell wall thickness is greatest at the bottom of the concave zone. The widest lumen diameter is the convex zone at the bottom position. This research can conclude that the FVB of nipa palm fronds, both longitudinal and radial, are included in quality class III, which is good enough to be used as raw material for pulp and paper.

Mechanical Properties and Deformation Behavior of Open-Cell Type Aluminum Foams with Structural Conditions and Alloy Composition

Open-cell type aluminum foams with various structural conditions and alloy compositions were manufactured using the replication casting process. The porosity of the foams ranged from 55% to 62%, with pore sizes of 0.7~1.0 mm, 1.0~2.0 mm, and 2.8~3.4 mm. The alloys employed included commercial A356 and A383, as well as Al-6Mg-(0, 2, 4, 6)Si alloys. Compression tests were conducted under various conditions of the foams, and the results were comparatively analyzed based on the detailed structural conditions and alloy compositions. It was observed that for the same alloy composition and equivalent porosity, a reduction in pore size led to an increased number of cell walls, enhancing energy dispersion and resulting in higher compressive yield strength and energy absorption. Under the same pore size, a decrease in porosity increased the relative density and cell wall thickness, leading to improved compressive yield strength and energy absorption. Furthermore, compressive evaluation based on alloy composition revealed the influence of the inherent mechanical properties of the material on the mechanical properties of open-cell type aluminum foams. Specifically, it was confirmed that alloys with higher ductility exhibited elastic behavior of the internal cells under external stress, significantly influencing the energy absorption of foams.

Identification and Analysis of the Mechanism of Stem Mechanical Strength Enhancement for Maize Inbred Lines QY1.

Enhancing stalk strength is a crucial strategy to reduce lodging. We identified a maize inbred line, QY1, with superior stalk mechanical strength. Comprehensive analyses of the microstructure, cell wall composition, and transcriptome of QY1 were performed to elucidate the underlying factors contributing to its increased strength. Notably, both the vascular bundle area and the thickness of the sclerenchyma cell walls in QY1 were significantly increased. Furthermore, analyses of cell wall components revealed a significant increase in cellulose content and a notable reduction in lignin content. RNA sequencing (RNA-seq) revealed changes in the expression of numerous genes involved in cell wall synthesis and modification, especially those encoding pectin methylesterase (PME). Variations in PME activity and the degree of methylesterification were noted. Additionally, glycolytic efficiency in QY1 was significantly enhanced. These findings indicate that QY1 could be a valuable resource for the development of maize varieties with enhanced stalk mechanical strength and for biofuel production.

Mesophyll conductance limits photosynthesis and relates to anatomical traits in high-elevation plants in the Andes

Plants face harsher conditions with increasing elevation, including shorter growing seasons, lower temperatures, and reduced gas pressure. This often leads to increased leaf mass per area, suggesting greater limitation to photosynthesis due to decreased mesophyll conductance. However, some species maintain consistent photosynthetic rates at higher elevations, suggesting compensatory mechanisms. In the central Chile Andes, high-elevation habitats present cold temperatures with no soil moisture deficits, whereas low-elevations experience warm temperatures and summer droughts. Zonal plants adapt to these changes, whereas azonal plants grow near water sources and avoid drought. We assessed how elevation affects photosynthesis and its limitations in these plant-types, together with the role of leaf internal anatomy. This was done with gas exchange and chlorophyll fluorescence analyses, along with measurements of leaf inner structure, on zonal and azonal species growing at 2600 and 3550 m a.s.l. Results showed that whilst photosynthesis decreased with elevation in azonal plants, zonal plants showed no change, with mesophyll conductance being a primary limitation, influenced by chloroplast arrangement rather that cell wall thickness. This affects carbon acquisition in high-elevation plants due to low gas pressure and light availability.

Bioinformatics-Driven mRNA-Based Vaccine Design for Controlling Tinea Cruris Induced by Trichophyton rubrum.

Tinea cruris, a dermatophyte fungal infection predominantly caused by Trichophyton rubrum and Epidermophyton floccosum, primarily affects the groin, pubic region, and adjacent thigh. Its recurrence is frequent, attributable to repeated fungal infections in susceptible individuals, especially those with onychomycosis or tinea pedis, which act as reservoirs for dermatophytes. Given the persistent nature of tinea cruris, vaccination emerges as a promising strategy for fungal infection management, offering targeted, durable protection against various fungal species. Vaccines stimulate both humoral and cell-mediated immunity and are administered prophylactically to prevent infections while minimizing the risk of antifungal resistance development. Developing fungal vaccines is challenging due to the thick fungal cell wall, similarities between fungal and human cells, antigenic variation, and evolutionary resemblance to animals, complicating non-toxic target identification and T-cell response variability. No prior research has shown an mRNA vaccine for T. rubrum. Hence, this study proposes a novel mRNA-based vaccine for tinea cruris, potentially offering long-term immunity and reducing reliance on antifungal medications. This study explores the complete proteome of T. rubrum, identifying potential protein candidates for vaccine development through reverse vaccinology. Immunogenic epitopes from these candidates were mapped and integrated into multitope vaccines and reverse translated to construct mRNA vaccines. Then, the mRNA was translated and computationally assessed for physicochemical, chemical, and immunological attributes. Notably, 1,3-beta-glucanosyltransferase, CFEM domain-containing protein, cell wall galactomannoprotein, and LysM domain-containing protein emerged as promising vaccine targets. Antigenic, immunogenic, non-toxic, and non-allergenic cytotoxic T lymphocyte, helper T lymphocyte, and B lymphocyte epitopes were selected and linked with appropriate linkers and Toll-like receptor (TLR) agonist adjuvants to formulate vaccine candidates targeting T. rubrum. The protein-based vaccines underwent reverse translation to construct the mRNA vaccines, which, after inoculation, were translated again by host ribosomes to work as potential components for triggering the immune response. After that, molecular docking, normal mode analysis, and molecular dynamic simulation confirmed strong binding affinities and stable complexes between vaccines and TLR receptors. Furthermore, immune simulations of vaccines with and without adjuvant demonstrated activation of immune responses, evidenced by elevated levels of IgG1, IgG2, IgM antibodies, cytokines, and interleukins. There was no significant change in antibody production between vaccines with and without adjuvants, but adjuvants are crucial for activating the innate immune response via TLRs. Although mRNA vaccines hold promise against fungal infections, further research is essential to assess their safety and efficacy. Experimental validation is crucial for evaluating their immunogenicity, effectiveness, and safety.

GhMAX2 Contributes to Auxin-Mediated Fiber Elongation in Cotton (Gossypium hirsutum).

Strigolactones (SLs) represent a new group of phytohormones that play a pivotal role in the regulation of plant shoot branching and the development of adventitious roots. In cotton (Gossypium hirsutum, Gh), SLs play a crucial role in the regulation of fiber cell elongation and secondary cell wall thickness. However, the underlying molecular mechanisms of SL signaling involved in fiber cell development are largely unknown. In this study, we report two SL-signaling genes, GhMAX2-3 and GhMAX2-6, which positively regulate cotton fiber elongation. Further protein-protein interaction and degradation assays showed that the repressor of the auxin cascade GhIAA17 serves as a substrate for the F-box E3 ligase GhMAX2. The in vivo ubiquitination assay suggested that GhMAX2-3 and GhMAX2-6 ubiquitinate GhIAA17 and coordinately degrade GhIAA17 with GhTIR1. The findings of this investigation offer valuable insights into the roles of GhMAX2-mediated SL signaling in cotton and establish a solid foundation for future endeavors aimed at optimizing cotton plant cultivation.

Mechanical strategies supporting growth and size diversity in Filamentous Fungi.

The stereotypical tip growth of filamentous fungi supports their lifestyles and functions. It relies on the polarized remodeling and expansion of a protective elastic cell wall (CW) driven by large cytoplasmic turgor pressure. Remarkably, hyphal filament diameters and cell elongation rates can vary extensively among different fungi. To date, however, how fungal cell mechanics may be adapted to support these morphological diversities while ensuring surface integrity remains unknown. Here, we combined super-resolution imaging and deflation assays to measure local CW thickness, elasticity and turgor in a set of fungal species spread on the evolutionary tree that spans a large range in cell size and growth speeds. While CW elasticity exhibited dispersed values, presumably reflecting differences in CW composition, both thickness and turgor scaled in dose-dependence with cell diameter and growth speeds. Notably, larger cells exhibited thinner lateral CWs, and faster cells thinner apical CWs. Counterintuitively, turgor pressure was also inversely scaled with cell diameter and tip growth speed, challenging the idea that turgor is the primary factor dictating tip elongation rates. We propose that fast-growing cells with rapid CW turnover have evolved strategies based on a less turgid cytoplasm and thin walls to safeguard surface integrity and survival.