Thick Detector Research Articles

Optimization of the Electron Spectrometer Telescope geometry for the PRESET satellite through Monte Carlo simulation

The Electron Spectrometer Telescope (EST) aboard the PRESET satellite mission aims to measure the pitch angle distribution of 0.3–4 MeV electrons in the outer Van Allen belts. The PRESET satellite is planned to launch into a sun-synchronous low Earth orbit in Q2, 2026. We present comprehensive Monte Carlo simulations to optimize the design and response of the EST instrument. The EST consists of a stack of silicon strip detectors and a collimator to take pitch-angle dependent electron spectral measurements with a target angular resolution of 6° while rejecting the proton, heavy ion and gamma detection events. Various collimator designs and detector stacking configurations are investigated using the Geant4 code to deduce an optimal design and configuration. For validation of the Geant4 simulations, a benchmark test spectrometer was set up using a stack of four silicon detectors and a good agreement between the measured and simulated responses was found for a beta spectrum from a 90Sr/90Y source. The collimator design was optimized by adjusting total length, aperture size, number of view-ports and collimator materials. The optimum aperture size and the number of view-ports were determined by varying them and selecting the best cases that meet the angular resolution and the geometric factor requirements. Moreover, to address the under-utilization of the front position-sensitive detector encountered in a typical pin-hole collimator, two offset collimators with tilted axes were employed. Extensive simulations were carried out by varying the number of silicon detectors and the thickness of each detector to optimize the configuration of the silicon detector stack. An optimum thickness of the front detector was found to be 140 µm, which can minimize the perturbation counts caused by the proton detection events. For the other detectors, a stack of four 1.5 mm thick detectors was chosen to achieve a good sensitivity to low energy electrons at a tolerable complexity of the system. The angular response simulated for the optimum design of the EST showed a resolution of 5.5°, which is slightly better than the target resolution of 6°. The response matrices of the final design simulated for isotropic electron and proton fields showed a high geometric factor, which is expected to produce an average electron counting rate of 230 cps within the trapped region with a negligible contamination of the electron spectrum by protons except for a mild contamination by the 1.0–1.1 MeV protons.

250 μm Thick Detectors for Neutron Detection: Design, Electrical Characteristics, and Detector Performances

Solid State Detectors (SSD) are crucial for fast neutron detection and spectroscopy in tokamaks due to their solid structure, neutron-gamma discrimination, and magnetic field resistance. They provide high energy resolutions without external conversion stages, enabling compact array installations in the harsh environment of a tokamak. Research comparing diamond and 4H-SiC detectors highlights thickness as a key efficiency factor. A 250 μm SiC epilayer with low doping, grown using a high-growth-rate process, exhibits sharp interfaces and minimal defects, essential for neutron detectors. The study evaluates detector designs, and performance using a 4H-SiC substrate. Various detector designs, such as Schottky diodes and p/n diodes, are assessed via I-V and C-V measurements, addressing high depletion voltage challenges. Preliminary neutron irradiation tests validate detector functionality, energy resolution and confirming detector reliability.

First measurements of energetic protons in Mega Amp Spherical Tokamak Upgrade (MAST-U).

First proton production rates from the d(d,p)t reaction in the Mega Amp Spherical Tokamak Upgrade (MAST-U) are measured. The data were taken during the MAST-U experimental campaign with an upgraded version of the proton detector (PD) previously used in MAST. The new detector array consists of three collimated silicon surface barrier detectors with a depletion depth of 300μm and a collimated 120μm thick diamond detector, mounted on the MAST-U reciprocating probe arm. This array measures the energies of unconfined energetic 3MeV protons and 1MeV tritons mainly produced by beam-thermal DD reactions during neutral beam injection heating. Diamond detectors have the potential to be uniquely suited to detect charged fusion products as they promise to be much more radiation resistant and much less sensitive to temperature variations compared to silicon-based detectors. Using silicon and diamond-based detectors simultaneously allowed us to directly compare the performance of these two detector types. PD particle rates measured during different plasma scenarios are presented and compared to neutron rates measured using the neutron camera upgrade and TRANSP predictions.

Performance evaluation of the 3D-ring cadmium–zinc–telluride (CZT) StarGuide system according to the NEMA NU 1-2018 standard

BackgroundThe application of semi-conductor detectors such as cadmium–zinc–telluride (CZT) in nuclear medicine improves extrinsic energy resolution and count sensitivity due to the direct conversion of gamma photons into electric signals. A 3D-ring pixelated CZT system named StarGuide was recently developed and implemented by GE HealthCare for SPECT acquisition. The system consists of 12 detector columns with seven modules of 16 × 16 CZT pixelated crystals, each with an integrated parallel-hole tungsten collimator. The axial coverage is 27.5 cm. The detector thickness is 7.25 mm, which allows acquisitions in the energy range [40–279] keV. Since there is currently no performance characterization specific to 3D-ring CZT SPECT systems, the National Electrical Manufacturers Association (NEMA) NU 1-2018 clinical standard can be tailored to these cameras. The aim of this study was to evaluate the performance of the SPECT/CT StarGuide system according to the NEMA NU 1-2018 clinical standard specifically adapted to characterize the new 3D-ring CZT.ResultsDue to the integrated collimator, the system geometry and the pixelated nature of the detector, some NEMA tests have been adapted to the features of the system. The extrinsic measured energy resolution was about 5–6% for the tested isotopes (99mTc, 123I and 57Co); the maximum count rate was 760 kcps and the observed count rate at 20% loss was 917 kcps. The system spatial resolution in air extrapolated at 10 cm with 99mTc was 7.2 mm, while the SPECT spatial resolutions with scatter were 4.2, 3.7 and 3.6 mm in a central, radial and tangential direction respectively. Single head sensitivity value for 99mTc was 97 cps/MBq; with 12 detector columns, the system volumetric sensitivity reached 520 kcps MBq−1 cc−1.ConclusionsThe performance tests of the StarGuide can be performed according to the NEMA NU 1-2018 standard with some adaptations. The system has shown promising results, particularly in terms of energy resolution, spatial resolution and volumetric sensitivity, potentially leading to higher quality clinical images.

Modelling Gd-diamond and Gd-SiC neutron detectors

A custom Monte Carlo (MC) computer model was developed to simulate thermal neutron absorption in, and subsequent photon and electron emission from, natural Gd with a view to using the material as a neutron conversion layer for neutron detectors. The MC code also modelled photon and electron detection with two dissimilar detectors: a thick (500 μm) single crystal diamond detector; and a thin (5.15 μm) commercial off the shelf (COTS) 4H–SiC photodiode detector. The detectors’ quantum detection efficiencies (QE) for hard X-rays and γ-rays were relatively low in comparison to their QE for electrons, thus making it possible to collect electron spectra from the Gd layer neutron conversion products which were not overwhelmed by photon emissions from the Gd. The MC code was utilised to determine the optimal thickness of Gd for the efficient detection of a thermal neutron flux. These radiation hard and spectroscopic detectors paired with natural Gd could find utility as robust and compact thermal neutron detectors for nuclear science and engineering, space science, and other applications.

Integrated Approach to the Optimization, Synthesis, Fabrication, and Application of ZnO-Based Sensors for Portable LPG Leakage Detection Systems

Liquefied petroleum gas (LPG) is used for cooking as well as in vehicles in the form of compressed natural gas (CNG) and in industries. As gas is volatile, there is the possibility of leakage which will be turned into take explosion or fire. It is a keen need to use the detection system for gas leakage for security purposes. ZnO thick film sensor was synthesized and fabricated by using the standard screen-printing method. The XRD pattern revealed that the ZnO thick film was polycrystalline, with an average crystallite size of around 27.1174 nm. The SEM scan revealed a ZnO particle size of around 1.88�m. Additionally, electrical and thermal properties were examined. This paper discussed the synthesized ZnO thick film LPG gas leakage detector prototype using Arduino ATMEGA8.

Alpha particle energy-range studies by a layer removal method in polycarbonate detectors for determining unknown ion energies

The aim of this study is to apply a “layer removal method” for alpha energy-range determination in polycarbonate detectors (PC) compared with SRIM software. This method is a precise chemical pre-etching process by which a layer of a certain thickness is removed from an exposed or unexposed PC detector surface before applying electrochemical etching (ECE). A group of 500 μm thick PC detectors was exposed to alpha particles of known fluence (∼1.0 × 104 alphas.cm−2) and ∼0.3–∼5.0 MeV energy range, followed by a pre-etching process at 12 different time intervals in 70% ethylenediamine solution. After the ECE process, alpha track density and diameter were determined. Track density versus removed layer thickness for each alpha energy follows a Bragg type peak after which approaching zero at a known removed layer thickness corresponding to the alpha range. The results also show a linear increase of the mean track diameter as the removed layer thickness increases for each energy. On the other hand, this study confirms a shift in the energy range registration by increasing the thickness of the removed layer. Using this precise method, an unknown energy can be determined by step-by-step thickness removal process until the track density approaches zero. In conclusion, the upper energy of ions emitted in a PFD can be determined. This method is a precise and simple method for ion energy-range determination studies for passive ion spectrometry.

Ultrawideband sub-pascal sensitivity piezopolymer detectors

Piezoelectric detectors are integral part of modern ultrasound imaging systems. Their utility has also been extended beyond the established methodologies into the emerging realm of hybrid optoacoustic imaging. Conventional piezoceramic detectors, however, struggle to combine high detection sensitivity with ultrawide bandwidth, both considered critical for attaining optimal optoacoustic imaging performance. Our research, both theoretical and empirical, unveils that damped piezopolymer detectors fabricated from PVDF-TrFE are markedly capable of achieving a synergistic blend between broad bandwidth and superb sensitivity. Experimental evaluations reflected an average sensitivity of 15.5 µV/Pa within a 1–10 MHz band for a 120 µm thick detector and 6.4 µV/Pa within a 1–30 MHz band for a 20 µm thick detector, thus outperforming conventional piezoelectric analogues. The resultant noise equivalent pressure (NEPs) values were 0.3 Pa and 1.2 Pa for the 20 µm and 120 µm detectors, respectively. Our findings herald a significant stride towards enhancing the efficacy of ultrawideband ultrasound and optoacoustic imaging systems.

Printed Thick Film Resistance Temperature Detector for Real-Time Tube Furnace Temperature Monitoring.

Accurately acquiring crucial data on tube furnaces and real-time temperature monitoring of different temperature zones is vital for material synthesis technology in production. However, it is difficult to achieve real-time monitoring of the temperature field of tube furnaces with existing technology. Here, we proposed a method to fabricate silver (Ag) resistance temperature detectors (RTDs) based on a blade-coating process directly on the surface of a quartz ring, which enables precise positioning and real-time temperature monitoring of tube furnaces within 100-600 °C range. The Ag RTDs exhibited outstanding electrical properties, featuring a temperature coefficient of resistance (TCR) of 2854 ppm/°C, an accuracy of 1.8% FS (full scale), and a resistance drift rate of 0.05%/h over 6 h at 600 °C. These features ensured accurate and stable temperature measurement at high temperatures. For demonstration purposes, an array comprising four Ag RTDs was installed in a tube furnace. The measured average temperature gradient in the central region of the tube furnace was 5.7 °C/mm. Furthermore, successful real-time monitoring of temperature during the alloy sintering process revealed approximately a 20-fold difference in resistivity for silver-palladium alloys sintered at various positions within the tubular furnace. The proposed strategy offers a promising approach for real-time temperature monitoring of tube furnaces.

Radiation tolerance test and performance verification of pnCCD at high temperatures for future satellite mission HiZ-GUNDAM

A wide-field X-ray survey in the soft X-ray band is crucial for future satellite missions in the astronomical observations. HiZ-GUNDAM, currently under development, is a proposed satellite designed to observe soft X-ray transients including gamma-ray bursts. This satellite employs wide-field X-ray monitors consisting of lobster-eye optics and focal-plane pixel sensors in the soft X-ray band of 0.4–4 keV. A pnCCD is a candidate for focal-plane Si pixel detectors, featuring a back-illuminated X-ray CCD, large pixel size (70–100 µm), and a large active image area of approximately 55 × 55 mm2 for the flight model. Here, we investigated the basic characteristics and performance of the small-size pnCCD with 128 × 256 pixels, a pixel size of 75 µm, and a detector thickness of 450 µm. High-energy cosmic rays such as protons can degrade the performance of pnCCDs by increasing dark current and charge transfer inefficiency due to ionizing and displacement damage. These factors may affect soft X-ray observations, potentially causing the degradation of lower-detectable energy thresholds and an increase in the number of hot pixels. Therefore, we conducted a radiation tolerance test at room temperature using a proton beam. After irradiating the pnCCD with 10-MeV protons equivalent to three years of nominal operation for HiZ-GUNDAM, we found that the operation temperatures of the pnCCD should be lower than -35 °C. This requirement will be incorporated into the design of the mission operation system.

Status of h-BN quasi-bulk crystals and high efficiency neutron detectors

III-nitrides have fomented a revolution in the lighting industry and are poised to make a huge impact in the field of power electronics. In the III-nitride family, the crystal growth and use of hexagonal BN (h-BN) as an ultrawide bandgap (UWBG) semiconductor are much less developed. Bulk crystals of h-BN produced by the high-temperature/high-pressure and the metal flux solution methods possess very high crystalline and optical qualities but are impractical to serve as substrates or for device implementation as their sizes are typically in millimeters. The development of crystal growth technologies for producing thick epitaxial films (or quasi-bulk or semi-bulk crystals) in large wafer sizes with high crystalline quality is a prerequisite for utilizing h-BN as an UWBG electronic material. Compared to traditional III-nitrides, BN has another unique application as solid-state neutron detectors, which however, also require the development of quasi-bulk crystals to provide high detection efficiencies because the theoretical efficiency (ηi) relates to the detector thickness (d) by ηi=1−e−dλ, where λ denotes the thermal neutron absorption length which is 47 μm (237 μm) for 10B-enriched (natural) h-BN. We provide an overview and recent progress toward the development of h-BN quasi-bulk crystals via hydride vapor phase epitaxy (HVPE) growth and the attainment of thermal neutron detectors based on 100 μm thick 10B-enriched h-BN with a record efficiency of 60%. The thermal neutron detection efficiency was shown to enhance at elevated temperatures. Benchmarking the crystalline and optical qualities of h-BN quasi-bulk crystals with the state-of-the-art mm-sized bulk crystal flakes and 0.5 μm thick epitaxial films identified that reducing the density of native defects such as vacancies remains the most critical task for h-BN quasi-bulk crystal growth by HVPE.

Single-layer Compton camera based on a 1 mm thick pixelated CDTE detectors

Compton camera is a novel γ-camera paradigm that relies upon the kinematics of Compton scattering for image reconstruction. A Conventional Compton camera uses two layers of sensors - the Absorber and the Scatterer. This work reports the proof of concept of a single-layer Compton camera (SLCC) where simultaneous Compton pairs events are registered in a single High-Z semiconductor sensor. The Hybrid pixel detector (HPD) is 1 mm thick, 256 x 256 square pixels with 55 μm pixel pitch CdTe sensor bonded to a Timepix3 readout ASIC. The superior spectroscopic imaging and fast timing capabilities of the Timepix3 readout ASIC coupled with a microscopic and highly pixelated CdTe enable simultaneous event detection of multi-energies occurring at multiple positions. The concept was exemplified by measuring the 122 KeV γ-ray emitted from a 57Co radioisotope source at two positions. Data were captured in the Timepix3 data-driven mode with the KATHERINE readout system via Gigabyte Ethernet data transfer. A bespoke Compton kinematics criterion algorithm implemented in Python 3 IDE was used for data analysis and Compton’s image reconstruction. Numerous events (5.2 million) were captured for 30-minute acquisitions. However, due to the thin nature of CdTe, fewer events (≈ 0.01 %) met the Compton event selection criteria. Nevertheless, the algorithm accurately pinpointed the radioisotope’s location, demonstrating proof of concept of the SLCC system.

Prototyping a High Purity Germanium cryogenic veto system for a bolometric detection experiment

The use of High Purity Germanium detectors operated in ionization mode at cryogenic temperatures is investigated as an external background mitigation solution for bolometers used in rare-event search experiments. A simple experimental setup, running a 52-g Li2WO4 bolometer sandwiched in-between two 2-cm thick High Purity Germanium cylindrical detectors in a dry cryostat, shows promising rejection to environmental gammas and atmospheric muons backgrounds. The acquired data are used together with a Monte Carlo simulation of the setup to extract the main contributions to the external backgrounds expected in an above ground experiment, such as e.g. current and future experimental efforts targeting the detection of coherent elastic neutrino-nucleus scattering at reactor facilities. Based on all these results, a 4π coverage similar veto system achieving a O(10 keV) energy threshold is expected to achieve a ≳73% and a ≳92% rejection power for gamma-like and muon-like events, respectively.

Characterisation of Redlen HF-CdZnTe at > 106 ph s-1 mm-2 using HEXITECMHz

In this paper, results are presented from the characterisation of Redlen Technologies high-flux-capable Cadmium Zinc Telluride (HF-CZT) hybridised to the HEXITECMHz ASIC, a novel 1 MHz continuous X-ray imaging system. A 2 mm thick HF-CZT HEXITECMHz detector was characterised on the B16 Test Beamline at the Diamond Light Source and displayed an average FWHM of 850 eV for monochromatic X-rays of energy 20 keV. Measurements revealed a shift in the baseline of irradiated pixels that results in a movement of the entire spectrum to higher ADU values. Datasets taken to analyse the effect's dynamics showed it to be highly localised and flux-dependent, with the excess leakage current generated equivalent to per-pixel shifts of ∼ 543 pA (8.68 nA mm-2) at a flux of 1.26×107 ph s-1 mm-2. Comparison to results from a p-type Si HEXITECMHz device indicate this `excess leakage-current' effect is unique to HF-CZT and it is hypothesised that it originates from trapping at the electrode-CZT interface and a temporary modification of the potential barrier between the CZT and metal electrode.

SiC based beam monitoring system for particle rates from kHz to GHz

The extremely low dark current of silicon carbide (SiC) detectors, even after high-fluence irradiation, was utilized to develop a beam monitoring system for a wide range of particle rates, i.e., from the kHz to the GHz regime. The system is completely built fromoff-the-shelf components and is focused on compactness and simple deployment. Beam tests using a 50 um thick SiC detector reveal, that for low fluences, single particles can be detected and counted. For higher fluences, beam properties were extracted from beam cross sections using a silicon strip detector.Overall, accurateresults were achieved up to a particle rate of 109 particles per second.

Investigation of Deconvolution Method with Adaptive Point Spread Function Based on Scintillator Thickness in Wavelet Domain.

In recent years, indirect digital radiography detectors have been actively studied to improve radiographic image performance with low radiation exposure. This study aimed to achieve low-dose radiation imaging with a thick scintillation detector while simultaneously obtaining the resolution of a thin scintillation detector. The proposed method was used to predict the optimal point spread function (PSF) between thin and thick scintillation detectors by considering image quality assessment (IQA). The process of identifying the optimal PSF was performed on each sub-band in the wavelet domain to improve restoration accuracy. In the experiments, the edge preservation index (EPI) values of the non-blind deblurred image with a blurring sigma of σ = 5.13 pixels and the image obtained with optimal parameters from the thick scintillator using the proposed method were approximately 0.62 and 0.76, respectively. The coefficient of variation (COV) values for the two images were approximately 1.02 and 0.63, respectively. The proposed method was validated through simulations and experimental results, and its viability is expected to be verified on various radiological imaging systems.

High-Density Glass Scintillators for Proton Radiography-Relative Luminosity, Proton Response, and Spatial Resolution.

Proton radiography is a promising development in proton therapy, and researchers are currently exploring optimal detector materials to construct proton radiography detector arrays. High-density glass scintillators may improve integrating-mode proton radiography detectors by increasing spatial resolution and decreasing detector thickness. We evaluated several new scintillators, activated with europium or terbium, with proton response measurements and Monte Carlo simulations, characterizing relative luminosity, ionization quenching, and proton radiograph spatial resolution. We applied a correction based on Birks's analytical model for ionization quenching. The data demonstrate increased relative luminosity with increased activation element concentration, and higher relative luminosity for samples activated with europium. An increased glass density enables more compact detector geometries and higher spatial resolution. These findings suggest that a tungsten and gadolinium oxide-based glass activated with 4% europium is an ideal scintillator for testing in a full-size proton radiography detector.

The Effect of Two Etching Solutions NaOH and KOH on Registration Properties and Etching of Polymer CR-39 Detectors

The solid – state nuclear track detector (SSNTDs) CR-39 can be used to study the different factors for alpha particle. Alpha particle is very dangerous inside the human body so the study its very important. In this article, we investigated the impact of two different etching solutions (NaOH and KOH)) on registrations properties, diameter D, track Diameter growth velocity VD, number of tracks and removal layer thickness of CR-39 nuclear track detector. The two types NaOH and KOH were dissolved in water with varied normality (3,5,7,9,11)N under a temperature of (70±1)°C to create the solution. During the experiment, a source of (α-particles) with a 4MeV energy was used to bombard all detectors (30 Sec). It was found the values of the diameter, number of tracks, removal layer thickness, track Diameter growth velocity VD by using the etching solution (NaOH +water) Solution greater than the values in (KOH + water) solution. the results showed excellent agreement with the outcomes of others who utilized different normalities.

Characterization of a flexible a-Si:H detector for in vivo dosimetry in therapeutic x-ray beams.

The increasing use of complex and high dose-rate treatments in radiation therapy necessitates advanced detectors to provide accurate dosimetry. Rather than relying on pre-treatment quality assurance (QA) measurements alone, many countries are now mandating the use of in vivo dosimetry, whereby a dosimeter is placed on the surface of the patient during treatment. Ideally, in vivo detectors should be flexible to conform to a patient's irregular surfaces. This study aims to characterize a novel hydrogenated amorphous silicon (a-Si:H) radiation detector for the dosimetry of therapeutic x-ray beams. The detectors are flexible as they are fabricated directly on a flexible polyimide (Kapton) substrate. The potential of this technology for application as a real-time flexible detector is investigated through a combined dosimetric and flexibility study. Measurements of fundamental dosimetric quantities were obtained including output factor (OF), dose rate dependence (DPP), energy dependence, percentage depth dose (PDD), and angular dependence. The response of the a-Si:H detectors investigated in this study are benchmarked directly against commercially available ionization chambers and solid-state diodes currently employed for QA practices. The a-Si:H detectors exhibit remarkable dose linearities in the direct detection of kV and MV therapeutic x-rays, with calibrated sensitivities ranging from (0.580±0.002) pC/cGy to (19.36±0.10) pC/cGy as a function of detector thickness, area, and applied bias. Regarding dosimetry, the a-Si:H detectors accurately obtained OF measurements that parallel commercially available detector solutions. The PDD response closely matched the expected profile as predicted via Geant4 simulations, a PTW Farmer ionization chamber and a PTW ROOS chamber. The most significant variation in the PDD performance was 5.67%, observed at a depth of 3mm for detectors operated unbiased. With an external bias, the discrepancy in PDD response from reference data was confined to±2.92% for all depths (surface to 250mm) in water-equivalent plastic. Very little angular dependence is displayed between irradiations at angles of 0° and 180°, with the most significant variation being a 7.71% decrease in collected charge at a 110° relative angle of incidence. Energy dependence and dose per pulse dependence are also reported, with results in agreement with the literature. Most notably, the flexibility of a-Si:H detectors was quantified for sample bending up to a radius of curvature of 7.98mm, where the recorded photosensitivity degraded by (-4.9±0.6)% of the initial device response when flat. It is essential to mention that this small bending radius is unlikely during in vivo patient dosimetry. In a more realistic scenario, with a bending radius of 15-20mm, the variation in detector response remained within±4%. After substantial bending, the detector's photosensitivity when returned to a flat condition was (99.1±0.5)% of the original response. This work successfully characterizes a flexible detector based on thin-film a-Si:H deposited on a Kapton substrate for applications in therapeutic x-ray dosimetry. The detectors exhibit dosimetric performances that parallel commercially available dosimeters, while also demonstrating excellent flexibility results.

High-energy electron measurements with thin Si detectors

A technique for measuring high-energy electrons using Si detectors of various thicknesses that are much smaller than the range of the examined electrons is presented. The advantages of the method are discussed on the basis of electron–positron pair creation recently studied in deuteron–deuteron fusion reactions at very low energies. Careful Geant4 Monte Carlo simulations enabled to identify the main spectral contributions of emitted electrons and positrons resulting from the energy loss mechanisms and scattering processes within the target, detector and their holders. Significant changes in the intensity of the detected electrons, depending on the detector thickness and the thicknesses of absorption foils placed in the front of the detector could be observed. The corresponding correction factors have been calculated and can be used for different applications in basic and applied research.