Thermal Characterization Research Articles

Surface Modification of Copper-Based Flakes for Conductive Polymer Composites.

The physical properties as well as thermal and electrical stability of copper particles can be improved by surface protection, which mainly depends on the coating material. Our study was, therefore, focused on the rheological, thermal, mechanical and electrical characterization of polymer composites by comparing uncoated (Cu), silver-coated (Cu@Ag) and silica-coated (Cu@Si) copper flakes in low-density polyethylene at various volume concentrations (up to 40%). Interactions among particles were investigated by rheological properties, as these indicate network formation (geometrical entanglement), which is important for mechanical reinforcement as well as establishing an electric pathway (electrical percolation). The results showed that geometrical and electrical percolation were the same for Cu and Cu@Si, ~15%, while, surprisingly, Cu@Ag exhibited much lower percolation, ~7.5%, indicating the fusion of the Ag coating material, which also decreased crystal growth (degree of crystallinity). Furthermore, the magnitude of the rheological and mechanical response remained the same for all investigated materials, indicating that the coating materials do not provide any load transfer capabilities. However, they profoundly affect electron transfer, in that, Cu@Ag exhibited superior conductivity (74.4 S/m) compared to Cu (1.7 × 10-4 S/m) and Cu@Si (1.5 × 10-10 S/m). The results obtained are important for the design of advanced polymer composites for various applications, particularly in electronics where enhanced electrical conductivity is desired.

Characterization and Implementation of Cocoa Pod Husk as a Reinforcing Agent to Obtain Thermoplastic Starches and Bio-Based Composite Materials.

When the cocoa pod husk (CPH) is used and processed, two types of flour were obtained and can be differentiated by particle size, fine flour (FFCH), and coarse flour (CFCH) and can be used as a possible reinforcement for the development of bio-based composite materials. Each flour was obtained from chopping, drying by forced convection, milling by blades, and sieving using the 100 mesh/bottom according to the Tyler series. Their physicochemical, thermal, and structural characterization made it possible to identify the lower presence of lignin and higher proportions of cellulose and pectin in FFCH. Based on the properties identified in FFCH, it was included in the processing of thermoplastic starch (TPS) from the plantain pulp (Musa paradisiaca) and its respective bio-based composite material using plantain peel short fiber (PPSF) as a reinforcing agent using the following sequence of processing techniques: extrusion, internal mixing, and compression molding. The influence of FFCH contributed to the increase in ultimate tensile strength (7.59 MPa) and higher matrix-reinforcement interaction when obtaining the freshly processed composite material (day 0) when compared to the bio-based composite material with higher FCP content (30%) in the absence of FFCH. As for the disadvantages of FFCH, reduced thermal stability (323.57 to 300.47 °C) and losses in ultimate tensile strength (0.73 MPa) and modulus of elasticity (142.53 to 26.17 MPa) during storage progress were identified. In the case of TPS, the strengthening action of FFCH was not evident. Finally, the use of CFCH was not considered for the elaboration of the bio-based composite material because it reached a higher lignin content than FFCH, which was expected to decrease its affinity with the TPS matrix, resulting in lower mechanical properties in the material.

Mineralogical, Geotechnical, Thermal and Mechanical Characterizations of an Energy-Efficient Building Material: Clay Stabilized by Wood Ashes or Crushed Waste from Traditional Pottery

Mineralogical, Geotechnical, Thermal and Mechanical Characterizations of an Energy-Efficient Building Material: Clay Stabilized by Wood Ashes or Crushed Waste from Traditional Pottery

In situ thermal conductivity measurement revealing kinetics of thermochemical reactions

Utilizing thermochemical reactions for thermal energy storage and solar fuel production has been an emerging research topic. Thermal transport properties of the materials are an important parameter that can determine the kinetics and efficiency of thermochemical reactions. With the increasing number of new thermochemical materials (TCMs); however, there is a lack of reliable techniques to monitor the thermal transport property of the materials and their changes as a function of reactions in real time. In this work, we report the in situ monitoring of thermochemical reactions using modulated photothermal radiometry (MPR). The thermal conductivities of two TCMs, namely, calcium hydroxide (Ca(OH)2) and Ba0.15Sr0.85FeO3−δ (BSF1585), were measured as a function of temperature and time using the MPR technique. The measured thermal conductivities were correlated to the reaction. The work has two significant contributions to the research communities. First, it provides a non-invasive diagnostic tool for monitoring the thermal transport properties of TCMs that can potentially be a high-throughput measurement technique conducive to optimizing TCMs, reactors, and related thermal systems. Second, for TCMs that show observable changes in thermal transport properties, a correlation between the measured thermal conductivity and the conversion fraction of the reaction can be established for monitoring the reaction kinetics based on thermal characterization.

Thermal, dosimetric and thermo-mechanical characterization of ABS and PLA polymer materials via plastic injection molding for innovative bolus materials in radiotherapy applications

The impact of radiation on polymer materials, and consequently on their mechanical and physical properties, is a burgeoning field of research. This research assesses the dosimetric, mechanical, and thermal characteristics of Acrylonitrile Butadiene Styrene (ABS) and Polylactic Acid (PLA) materials developed through plastic injection molding as possible alternatives to commercial bolus used in radiotherapy. The materials were thoroughly compared with the commercial bolus material, EXAFLEX, by various tests such as Hounsfield Unit (HU) Analysis, Radiation Transmittance, Thermogravimetric Analysis (TGA), Thermomechanical Analysis (TMA), and Fourier Transform Infrared Spectroscopy (FTIR). The research indicates that ABS and PLA materials have similar radiological qualities to EXAFLEX, showing constant surface and accumulation area doses. Minor differences are seen deeper inside the phantom, indicating a stable tissue equivalency. ABS demonstrated strong resistance to radiation-induced chemical modifications, but PLA exhibited susceptibility to molecular changes. The TMA findings showed that radiation caused a decrease in softening temperatures and an increase in the coefficient of thermal expansion for both ABS and PLA, indicating changes in their thermal stability and mechanical characteristics after irradiation. The study highlights the potential of ABS and PLA materials made through plastic injection molding as efficient and safety substitutes for commercial bolus materials, particularly for large area irradiation. This requires more research into their clinical uses and consequences.

Enrichment of Trypsin Inhibitor from Soybean Whey Wastewater Using Different Precipitating Agents and Analysis of Their Properties.

Recovering valuable active substances from the by-products of agricultural processing is a crucial concern for scientific researchers. This paper focuses on the enrichment of soybean trypsin inhibitor (STI) from soybean whey wastewater using either ammonium sulfate salting or ethanol precipitation, and discusses their physicochemical properties. The results show that at a 60% ethanol content, the yield of STI was 3.983 mg/mL, whereas the yield was 3.833 mg/mL at 60% ammonium sulfate saturation. The inhibitory activity of STI obtained by ammonium sulfate salting out (A-STI) was higher than that obtained by ethanol precipitation (E-STI). A-STI exhibited better solubility than E-STI at specific temperatures and pH levels, as confirmed by turbidity and surface hydrophobicity measurements. Thermal characterization revealed that both A-STI and E-STI showed thermal transition temperatures above 90 °C. Scanning electron microscopy demonstrated that A-STI had a smooth surface with fewer pores, while E-STI had a rough surface with more pores. In conclusion, there was no significant difference in the yield of A-STI and E-STI (p < 0.05); however, the physicochemical properties of A-STI were superior to those of E-STI, making it more suitable for further processing and utilization. This study provides a theoretical reference for the enrichment of STI from soybean whey wastewater.

Failure analysis of thermoplastic composites subject to galvanic corrosion in hybrid metal–composite joints

The damage sustained by carbon fibre reinforced polymers due to the effect of galvanic corrosion induced by coupling between carbon fibres and a metallic material in a hybrid joint is investigated. Composite laminates with two fibre architectures and two thermoplastic matrices (polycarbonate and polyamide 6) are coupled to a metallic fastener and exposed to salted fog conditions. Both the effects of the salted fog environment and the coupled effect of the environmental and the galvanic corrosion are analysed. The analysis is centred in, firstly, characterising the functional properties of the hybrid joint, secondly characterising the laminate properties and finally characterising the chemical degradation of the matrix. The results show a degradation of properties for the polycarbonate material, in terms of bearing performance and interlaminar shear strength as well as presenting obvious changes in the thermal characterisation. The polyamide composites remain largely unaffected and only minor changes in the surface appearance are noteworthy.

Publisher's Note: “Phase change-related thermal property characterization and enhancement in carbon-based organic phase change composites” [Appl. Phys. Rev. 11, 021322 (2024)

Publisher's Note: “Phase change-related thermal property characterization and enhancement in carbon-based organic phase change composites” [Appl. Phys. Rev. <b>11</b>, 021322 (2024)

Evaluation of the Temperature Sensitivity of the Lachrymatory Irritant 2-Chlorobenzalmalononitrile by Differential Scanning Calorimetry and Gas Chromatography-Mass Spectrometry

Abstract Pyrotechnic compositions are mixtures of several components which, when ignited, undergo energetic chemical reactions at a controlled rate to produce on-demand delay times, amounts of heat, noise, smoke, light or IR radiation. In general, pyrotechnic compositions are easily ignited, burn quickly and produce residues that are very hot. 2-Chlorbenzalmalononitrile (CS) belongs to the category of riot control agents and is used in various pyrotechnic tear gas compositions. The thermal characterization of tear pyrotechnic compositions is important for setting operating limits in the safety of the production process, storage, handling and even safe demilitarization. In this sense, an experimental study was carried out to evaluate the behavior of CS at high temperatures, at different heating rates, by differential scanning calorimetry. Thermal changes were evaluated at a heating rate of 10, 20, 100 and 200οC/minute. The remaining residue was extracted in a suitable organic solvent and analyzed by gas chromatography coupled with mass spectrometry for the detection, identification and confirmation of the products formed during the controlled heating processes.

Artificial Intelligence Approach for Bio-Based Materials’ Characterization and Explanation

This paper introduces a numerical methodology for classifying and identifying types of bio-based materials through experimental thermal characterization. In contrast to prevailing approaches that primarily focus on thermal conductivity, our characterization methodology encompasses several thermal parameters. In this paper, the physical characteristics of seven types of bio-based concrete were analyzed, focusing on the thermal properties of palm- and esparto-fiber-reinforced concrete. The proposed method uses artificial intelligence techniques, specifically the k-means clustering approach, to segregate data into homogeneous groups with shared thermal characteristics. This enables the elucidation of insights and recommendations regarding the utilization of bio-based insulation in building applications. The results show that the k-means algorithm is able to efficiently classify the reference concrete (RC) with a performance of up to 71%. Additionally, the technique is more accurate when retaining only six centroids, which, among other things, allows all the characteristics associated with each type of concrete to be grouped and identified. Indeed, whether for k clusters k = 7 or k = 5, the technique was not able to predict the typical characteristics of 2% or 3% esparto concrete (EC).

Paracoccus kondratievae produces poly(3-hydroxybutyrate) under elevated temperature conditions.

As part of ongoing efforts to discover novel polyhydroxyalkanoate-producing bacterial species, we embarked on characterizing the thermotolerant species, Paracoccus kondratievae, for biopolymer synthesis. Using traditional chemical and thermal characterization techniques, we found that P. kondratievae accumulates poly(3-hydroxybutyrate) (PHB), reaching up to 46.8% of the cell's dry weight after a 24-h incubation at 42°C. Although P. kondratievae is phylogenetically related to the prototypical polyhydroxyalkanoate producer, Paracoccus denitrificans, we observed significant differences in the PHB production dynamics between these two Paracoccus species. Notably, P. kondratievae can grow and produce PHB at elevated temperatures ranging from 42 to 47°C. Furthermore, P. kondratievae reaches its peak PHB content during the early stationary growth phase, specifically after 24 h of growth in a flask culture. This is then followed by a decline in the later stages of the stationary growth phase. The depolymerization observed in this growth phase is facilitated by the abundant presence of the PhaZ depolymerase enzyme associated with PHB granules. We observed the highest PHB levels when the cells were cultivated in a medium with glycerol as the sole carbon source and a carbon-to-nitrogen ratio of 10. Finally, we found that PHB production is induced as an osmotic stress response, similar to other polyhydroxyalkanoate-producing species.

Thermal, morphological, and structural characterization of starch-based bio-polymers for melt spinnability

Abstract The demand for sustainable textiles has increased research on bio-based biopolymers. Fiber spinning from starch biopolymer and its blends was widely attempted using electro-spinning; however, it is less attempted using melt spinning which is an industrially feasible method. In this study, native tapioca starch is converted into thermoplastic starch (TPS), blended with polylactic acid (PLA), and is attempted for melt spinnability in its neat and blended form TPS/PLA (70/30) with the intention of checking the possibility of melt spinning. The results from characterization of the prepared biopolymers show that thermal analysis of neat TPS does not reveal clear thermal transitions, glass transition (T g), and melting (T m), in the second heating curve, rather it influenced crystallization behavior of PLA as seen from differential scanning calorimetry result and degradation temperature (T d) was found to be in the range of 296–352°C from thermogravimetric analysis showing that addition of PLA improved thermal stability of TPS. Morphology analysis with AFM images revealed the presence of granular starch in neat TPS and phase separation in TPS/PLA blends with finer phase distribution in the presence of additives. Fourier transform infrared spectroscopy result shows the interaction between starch, glycerol, and PLA showing the effect of thermoplasticization of starch which brings rupture or weakening of the strong glycosidic bonds in between starch molecules and interaction between TPS and PLA as it can be seen from peak shift and peak intensity. The melt spinning trials show the possibility of melt spinning TPS-based biopolymers into fibers even with higher content of TPS as well as neat TPS giving an insight and motivation for more research engagement. The melt-spun fibers were found to have a diameter in the range of 160.0–117.0 μm. However, additional experiments and investigations are required to improve the mechanical and other properties of the fibers.

Enhancing sustainability in polymer 3D printing via fusion filament fabrication through integration of by-products in powder form: mechanical and thermal characterization

FFF (fused filament fabrication) is a type of 3D printing that utilizes filament for part creation. This study proposes using by-products or waste to replace part of the plastic in FFF filament, reducing environmental impact. The aim is to maintain a simple manufacturing process involving extrusion on a single-screw desktop machine followed by printing. The plastic matrix comprises polylactic acid (PLA) and polyethylene glycol (PETG), with added powdered by-products: seashells, car glass and mill scale (metal). Additives will be incorporated at 10% and 20% by weight, with two grain sizes: up to 0.09 mm and up to 0.018 mm. Mechanical tests (tensile, flexural and hardness) and thermal characterization tests will be conducted. Findings suggest adding 10%w powder of any variety to PETG increases tensile strength up to 48%, with metal powder (mill scale) showing the highest enhancement, even at 20%w, resulting in a 41% increase. Conversely, adding powder to PLA worsens mechanical properties without stiffening the material; instead, the elastic modulus decreases. Metal grain size has minimal impact, with grain sizes lower than 0.09 mm optimal for PLA. Thermal conductivity in polymers blended with powder additives is lower than in virgin polymers, likely due to air void formation, supported by density and microscopic evaluations. This research underscores the potential of utilizing waste materials with a simple FFF filament production to enhance sustainability in 3D printing practices.

Experimental investigation of 3D printed polylactic acid and polylactic acid – hydroxyapatite composite through material extrusion technique for biomedical application

In biomedical industries, composite additive manufacturing are employed for customization, quicker production, efficient use and capital reduction. This experimental work focuses on the development of poly lactic acid (PLA) and novel extruded hydroxyapatite (HA) reinforced poly lactic acid (HPLA) by material extrusion (ME) technique and their properties were compared with that of standard 3D printed PLA. The extruded composite filaments were subjected to thermal characterization (DSC, TGA) and chemical characterization (FTIR) to ensure filament quality and its implementation in ME technique for 3D printing process. In addition, the melt compounded composite filaments were subjected to annealing to observe the influence of heat treatment upon their mechanical properties and thereby to validate their potential to resist breakage during ME process. Taguchi orthogonal array method using MiniTab software is employed to execute the parameter optimization for the 3D printing process. The 3D printed tensile, flexural and impact specimens, using pure PLA and extruded composite filaments, as per American Society for Testing and Materials (ASTM) standards were subjected to a comparative experimental study which showed that 3D printed specimens using PLA and HPLA performed better than that of standard PLA specimens due to the improvement in their crystalline nature. The ruptured specimens were subjected to microstructural characterization (optical microscopy, SEM) to observe failure modes and ash content test was conducted to validate the homogenous distribution HA filler particles in PLA matrix. In addition, mechanical characterization was also performed on 3D printed bone plate/bone scaffold application using extruded filaments of PLA and HPLA, as per ASTM F543 standards, to validate incorporation of the composite filaments in real-time application in biomedical industry.

Thermal characterization of Sutterby nanofluid flow under Riga plate: Tiwari and Das model

This investigation uses the Tiwari and Das nanofluid model to enhance the heat transfer rate in Sutterby nanofluid over a Riga plate. The effects of heat source/sink, viscosity dispersion, and mass flow for water-based fluids are also considered in this work. Sutterby fluid has been utilized to investigate the rheological features of nanofluids. The transverse Lorentz force produced by the Riga plate assists in the flow down the plate by producing an electromagnetic field. The main aim of this investigation is to evaluate the presence of two different types of nanoparticles in water, specifically silicon carbide [Formula: see text] and copper [Formula: see text]. Dimensionless variables are first used to convert the mathematical model into a non-dimensional form. The similarity approach is then used to further rewrite the non-dimensional partial differential equations into a set of similarity equations. The bvp4c function in MATLAB software provides a numerical solution to these equations. The effects on temperature and velocity profiles of many physical factors, including the Reynold number, heat source/sink, and Deborah number, have been analyzed and presented. Furthermore, using tables, a detailed analysis of the skin friction coefficient and local Nusselt numbers is conducted. The results show that convective flow is suppressed when solid nanoparticles are added to the base fluid. The velocity distribution improves as Deborah and Reynold’s numbers get a higher value. Also, the temperature field improves by incrementing exponential and thermal heat source/sink parameters.

Polyaniline/titanium phosphate as a biosensor detection of glucose performance

In this study, we have prepared titanium phosphate (TiPO4) by photolysis-hydrothermal method, and then incorporated it with polyaniline (PANI) by oxidative polymerization method. FTIR, XRD and XPS confirmed the formation of nanocomposite. TGA analysis were also carried out for thermal stability characterization. The TiPO4/PANI nanocomposite has been employed as a biosensor for glucose disclosure via immobilization with glucose oxidase enzyme. Amperometry, cyclic voltammetry (CVs) and chemical impedance (EIS) were carried out for sensing of glucose. The linear range of glucose detection was noted from 20 to 100 μM by using amperometric analysis, and the LOD was found to be 5.44 μM.

On the influence of graphene oxide and hydroxyapatite modification on alginate-based hydrogel matrix: thermal, physicochemical, and biological considerations

Sodium alginate (SA) hydrogels with an addition of graphene oxide (GO) and hydroxyapatite (HAp) crosslinked by calcium chloride solution were investigated as potential materials for osteochondral tissue regeneration. The influence of various ratios of the nanoadditives in the natural derived polymer matrix on the thermal, physiochemical and biological properties was studied. Two thermal characterization methods (DSC and TGA) were employed to examine the thermal properties of the materials and provide information regarding the different types of water within the hydrogel structure. These parameters are crucial for the assessing and understanding of the adsorption/desorption processes in hydrogels and also impact their biocompatibility. The effect of GO and HAp addition on thermal characteristics of alginate hydrogel is reported, as well as the nanoadditives polymer chains interaction, as evidenced by FTIR results. The compression test confirmed that the nanoadditives, uniformly dispersed in the polymer matrix, improved the mechanical properties of the hydrogels, but only up to a certain content of additives. The composite hydrogels exhibited a very low friction coefficient. Both GO and HAp also enhanced chemical stability of alginate hydrogels under in vitro conditions. Biological assays demonstrated that most of the tested hydrogel extracts were not cytotoxic to hUC-MSCs, but they can affect the proliferation rate of the cells. Developed materials may present an intriguing alternative for osteochondral tissue regeneration.

Thermal Characterization of [C2Im][NO3] and Multivalent Nitrate Salts Mixtures

Due to their intrinsic properties, the current applicability of ionic liquids is enormous. In particular, their use in electrochemistry is beyond question. Numerous studies on these compounds and their mixtures, especially with lithium salts, focus on their use as electrolytes for batteries and other energy storage devices. This includes thermal energy storage devices, where 4th generation ionic liquids and their derivatives show a huge potential. Nevertheless, considering the uneven availability of the raw materials, such as lithium, research has extended to mixtures of these compounds with other salts of different metals that are more abundant and widely distributed, such as magnesium or aluminum. This work presents a comprehensive thermal characterization, using differential scanning calorimetry and thermogravimetry, of the protic ionic liquid ethylimidazolium nitrate and its mixture with magnesium and aluminum nitrate salts at different concentrations. Additionally, a comparison between these results and previous studies of mixtures of this ionic liquid with lithium nitrate, as well as mixtures of the protic ionic liquid EAN with the same metal salts, was also performed. The results indicated that the salt addition tends to broaden and reduce crystallization and melting peaks, while the glass transition becomes more visible and shifts to higher temperatures with increasing salt concentration. This is due to the disorder generated by the rearrangement of ions in the polar domains, which erodes the hydrogen bond network of the protic ionic liquid. Nevertheless, the thermal stability of the blended samples does not change significantly compared to the bulk ionic liquid.

Preparation of CuBTC@PET Hierarchically Porous Composite Membranes via In Situ Growth Method and Their Antibacterial Filtration Performance

Processing polyethylene terephthalate (PET) into functional materials has both sustainable and economic significance. Therefore, this study aims to prepare functional nanofibers using PET, combining electrospun nanofibers with metal–organic frameworks (MOFs), which is an effective solution to increase the added value of functional nanofiltration membranes (NFMs). The surface morphology of PET fibers is successfully controlled by electrospinning parameters and post-treatment. The formation of a uniform coating of CuBTC crystals on the PET surface is induced by a simple and low-cost in situ growth technique. CuBTC@PET was treated to prepare superhydrophobic CuBTC@PET (SCP), thus improving the stability of CuBTC in water and expanding its potential applications. Through a series of optical and thermal characterizations, the porous morphology formation mechanism and MOF in situ growth mechanism of SCP fibers were discussed. Then, the air filtration performance and bacteriostatic properties of SCP nanofiltration membranes were investigated. The as-prepared SCP showed a high water contact angle (146.4°), low-pressure drop (39.7 Pa), and high filtration efficiency (95.3%, 3 μm NaCl), as well as unique, broad-spectrum antibiosis potency against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli). This study shows that SCP nanofiltration membranes can be practically applied in high-performance antibacterial filtration membranes.

Phase change-related thermal property characterization and enhancement in carbon-based organic phase change composites

By utilizing the significant amount of energy absorbed and released during their phase transitions, phase change materials (PCMs) can capture and store thermal energy to fill gaps between supply and demand. Due to their many favorable properties, organic PCMs have gained attention in a wide range of applications. Nevertheless, their inherent low thermal conductivity has limited the direct use of organic PCMs in thermal energy storage (TES). Extensive research has been conducted on enhancing organic PCM thermal conductivity by incorporating high thermal conductivity materials. Owing to their high thermal conductivity and low density, carbon-based materials have been extensively used for thermal conductivity enhancement in phase change composites (PCCs). Carbon-based organic PCCs, which incorporate highly thermally conductive carbon allotropes and their direct chemical derivatives with organic PCMs, are a group of diverse PCCs with highly promising potential for TES applications. Adequate latent heat and shape stability performances are crucial to the success of the applicational performances of these PCCs. Much empirical research has pushed efforts to enhance these phase change properties, yet a logical understanding of these enhancement efforts based on the thermodynamics and intermolecular interactions of carbon-based organic PCCs has been elusive. In particular, the effect of characterization methods on the evaluation of phase change properties has been largely understudied. This review strives to provide novel physical and chemical insights into latent heat and shape stabilization evaluation processes and enhancement efforts in carbon-based organic PCCs through a detailed review and analysis of recent literature. The review provides an unprecedented comprehension of newly developed PCCs that challenge the traditional understanding that the latent heat of PCCs cannot exceed that of its base PCM. Efforts on phase change property enhancement driven by these new insights have the potential for carbon-based organic PCCs to succeed in a variety of TES applications, including solar-thermal harvesting, thermal management of batteries and electronics, thermoregulating textiles, and infrared stealth and infrared responsive materials.