Thermal Capacity Research Articles

Impact of Temperature Variations on Torque Capacity in Shrink-Fit Junctions of Water-Jacketed Permanent Magnet Synchronous Motors (PMSMs)

This study investigates the impact of temperature variations on the torque capacity of shrink-fit junctions in water-jacketed permanent magnet synchronous motors. Focusing on both baseline and improved designs; torque capacities were evaluated across a temperature range from −40 °C to 120 °C under different material conditions: Least material condition, nominal, and maximum material condition. The baseline design exhibited torque capacities from 7648 Nm to 9032 Nm at −40 °C, decreasing significantly to 549 Nm to 1533 Nm at 120 °C. The improved design showed enhanced performance, with torque capacities ranging from 8055 Nm to 9247 Nm at −40 °C and from 842 Nm to 1618 Nm at 120 °C. The maximum improvement was observed at 120 °C for least material conditions, with a 55.4% increase, and the minimum improvement at −40 °C for maximum material conditions, with a 2.4% increase. Our findings demonstrate a significant increase in torque capacity by up to 20% under varied thermal conditions. These results underscore the effectiveness of design modifications in enhancing thermal stability and torque capacity, making the improved design a more reliable choice for high-performance applications subject to significant thermal fluctuations. This research highlights the critical role of material selection, thermal management, and precise design adjustments in optimizing the performance and reliability of permanent magnet synchronous motors.

Computational and experimental analysis of PCM-infused brick for sustainable heat regulation

Examining the thermodynamics of phase change materials (PCMs) when merged into construction materials is a significant subject within the realm of building science and environmental responsibility. When infused to construction materials like bricks, PCMs have the capacity to elevate a building’s temperature regulation by minimizing the energy required for thermal contentment. This research is dedicated to learn about the thermal conduct and the consequences of the fusion of calcium chloride hexahydrate mineral (CCHPCM) within the pores of a masonry unit. To achieve this, we implemented a practical testing specifically designed to scrutinize how CCHPCMs alter the thermal performance of studied compounds. Multiple configurations were designed by adjusting the arrangement of CCHPCM within the bricks, resulting in three distinct setups. The first set involved filling one row of the bricks, the second set entailed filling two rows, and the final configuration entailed filling all the pores with PCM. Additionally, a computational modeling was executed to survey the thermic behavior of bricks infused with CCHPCM, operating with COMSOL Multiphysics application program. The elaborated work concluded to having an enhancement of the brick’s thermal storage capacity, for Set-3, in which all rows of bricks are filled with PCM, a delay of 2 h is observed compared to Set-0 the brick without CCHPCM. This simulation also encompassed comparative findings regarding the thermal performance of CCHPCM when incorporated into the masonry unit. Overall, this study supplied the valorization of CCHPCMs infused in masonry units and their usage in distinct layouts on upgrading its candidature to achieving environmental responsibility.

Optimal refrigerant selection and parameter analysis of a wastewater heat pump using CO2 zeotropic mixtures

Heat pump technology can effectively recover waste heat from low-grade wastewater, which is crucial for energy conservation and carbon emission reduction in buildings. In this study, zeotropic mixtures were used to recover heat from low-grade wastewater and produce high-temperature water in a heat pump. The deep recovery of waste heat was realized by using a CO2 zeotropic mixture with a large glide temperature. Furthermore, this method ensures an excellent temperature matching between the heat transfer fluids and effectively reduces irreversible losses. To obtain an optimal zeotropic mixture, a method based on heuristic screening of the optimal CO2 zeotropic mixture was proposed. Furthermore, a model of a CO2 zeotropic mixture heat pump was established and experimentally validated. Based on the validated model, a sensitivity analysis of the various operating parameters of the heat pump was conducted. The results show that the zeotropic mixture CO2/R1234yf with a mass fraction of 0.17/0.83 is selected as the optimal refrigerant for the heat pump with the coefficient of performance, exergy efficiency and volumetric heating capacity of 7.46, 0.37, and 7978 kJ⋅m−3, respectively. The sensitivity analysis of operating parameters shows that the inlet temperature of hot water has more crucial influence on the coefficient of performance and exergy efficiency than various operating parameters, with sensitivity coefficients of −0.3868 and 0.2157, respectively. The volumetric heating capacity and system total exergy destruction per heating capacity unit are most sensitive to the flow rate of wastewater and hot water, with sensitivity coefficients of 0.1121 and −0.4985, respectively. These results provide a foundation for the design and optimization of a CO2 zeotropic mixture heat pump system.

Configuration method for medium-deep ground source heat pump system considering renewable energy consumption and smart grid interaction

Medium-deep ground source heat pump (GSHP) systems have the advantages of low carbon, high heat exchange intensity, good thermal storage capacity, and intermittent operation characteristics, which are conducive to renewable energy consumption and grid demand response. The source-side parameters affect the configuration of underground borehole engineering, heat pump units, and other equipment. However, current research mainly focuses on the underground heat exchanger modeling, underground heat exchange, and system operation control, while there are few studies on multi-factor ground source-side parameter design and optimal configuration. In this study, the indicator analyzing the unsteady features and thermal balance state of medium-deep geothermal resources was introduced, and the source-side water temperatures were optimized based on the dynamic characteristics of the geothermal and building sides. A simulation configuration methodology for the source-side flow rate and storage capacity was developed considering the electricity prices, life-cycle cost (LCC), and grid interaction. The optimization of the ground source-side design temperature, flow rate, and capacity parameters of residential and office building heating scenarios were analyzed in northern China, respectively. The results showed that the borehole inlet and outlet temperature can be designed to 5.5 °C/17.5 °C under the annual sustainable state, and the optimal flowrate can be set to 65.77 m3/h, to achieve the lowest cost and highest heating season guarantee rate for the residential scenario. For the office building with optimal system and storage capacity, the average annual LCC is 192,000 yuan/year, with the cumulative peak shaving of 55.8 %, and an increase of 103.3MWh renewable electricity consumption.

RADIANT HEATING AND COOLING SYSTEM EFFICIENCY OF OFFICE PREMISE BASED ON TABS

In this article the specific heating and cooling capacity of the ceiling TABS was determined. The step of tube laying varied and was 10, 15, 20, 25, and 30 cm. Determination of the specific heating capacity was carried out for th /tc = 35/31; 36/32; 34/30 oC. The determination of the specific cooling capacity was carried out for tcold /theated = 15/18; 16/19; 16/20oC. The radiant heating system based on ceiling TABS allows providing the necessary heating capacity to fully cover the heat loss of the room. The maximum values of the carrier temperature are th /tc = 34/30 oC. In the warm period, the ceiling TABS does not allow to provide the necessary cooling capacity of the room. Thus, the greatest cooling capacity of TABS is observed at coolant parameters tcold /theated = 15/18оC, which allows covering about 70% of the estimated heat gains of the room. Therefore, during the hours of peak heat gains an additional cooling device should be used in the room.

Magnetically assembled flexible phase change composites with vertically aligned structures for thermal management and electromagnetic interference shielding

Phase change material (PCM) is promising in achieving zero-energy thermal management because of its prominent thermal storage capacity and steady phase-change temperature. However, low intrinsic thermal conductivity (TC), liquid leak, and solid rigidity are long-standing bottlenecks for heat-related applications. Here, we report an innovative dual-encapsulation strategy to develop multifunctional phase change composite (FMP) with vertically aligned NdFeB@Ag arrays and styrene-ethylene-propylene-styrene (SEPS) crosslinked network in paraffin (PA). The NdFeB@Ag arrays induced by magnetic-field driven procedure can offer the consecutive/oriented highways for efficient heat-transfer, and an electric/magnetic heterostructure for electromagnetic interference shielding efficiency (EMI SE). The flexible SEPS block copolymer not only ensures the high flexibility of PCM, but also combines with oriented NdFeB@Ag arrays for dual encapsulating PA. This multifunctional FMP can achieve high TC of 2.59 W m−1 K−1, attractive EMI SE of 35.42 dB, prominent enthalpy density of 120 J g−1, and impressive Joule heating performance, together with leakage-proof, dynamic assembly, and salient charging/discharging durability. Furthermore, the FMP-supported device is demonstrated for thermal energy harvesting and utilization. This dual-encapsulation design opens a new avenue for exploiting multifunctional PCMs for thermal management, anti-EM radiation, and low-grade exhaust heat utilization.

Optimal sizing and energy management strategy for an office building with photovoltaic, heat pump, thermal tank, and electric vehicle under time-of-use tariff

The increasing demand for sustainable energy solutions is driving the integration of various renewable energy technologies. Integrating electric vehicle batteries, photovoltaics, heat pumps, and thermal tanks into building energy systems offers a promising approach to enhancing energy flexibility and efficiency. However, research on such integrated energy systems is still in its infancy. Optimizing the configuration and operation of the system may lead to significant cost savings and improved energy management. A coupled model and simulation-based optimization approach are used to optimize the thermal tank capacity and key operational parameters to minimize the annual total cost. The results show that the integrated energy system reduces the annual total cost by 36.35% and monthly electricity bills by up to 69.26% compared to the base system. As for energy flexibility, only 13.91% of electricity demand is supplied by the grid during peak periods, and the monthly load coefficient, load cover ratio, and photovoltaic self-consumption ratio of the integrated energy system are significantly improved. This study demonstrates the economic and operational benefits of integrating various renewable energy technologies into building energy systems and provides new insights into their design and optimization.

Research on working characteristics of composite two-stage ventilation heat recovery system with heat pipe and heat pump

In this paper, a composite two-stage ventilation heat recovery system with heat pipe and heat pump is proposed, heat pipe is used to recover the exhaust air energy to improve the operating performance of the system under all operating conditions. The split heat pipe heat exchanger is designed and manufactured, the working characteristics and performance of the composite heat recovery system under different working conditions are tested, and it is compared with the parallel-loop heat pump ventilation heat recovery system also. The results show that the optimal working fluid charge rate of the split heat pipe used in the composite system is 50 %–60 %, the temperature efficiency of the composite system in winter is higher than 64.31 %, the heating COP is up to 7.17, and the total heating capacity is 5.09 kW. Temperature efficiency and heating capacity of the system are 4.01 %–66.6 % and 7.68 %–67.19 % higher than that of the double loop heat pump heat recovery system, respectively.

Characterization of microstructure, texture, grain structure, and thermal properties of Al/Ni/Al multilayered composites fabricated through cross-accumulative roll bonding

This research investigates microstructure, texture, and thermal properties of Al/Ni/Al composites fabricated by cross-accumulative roll bonding (CARB) process. According to the microstructural results, ultra-fine grain structure was observed in severely deformed layers. More grain refinement occurred when the content of Ni increased. In addition, shear texture components became stronger by increasing the CARB passes and Ni content even though the Copper-based texture components of {112}<111> existed in all deformed samples. Also, despite an improvement in thermal features of deformed aluminum and nickel layers versus temperature rise, the TD, and TC decreased as the number of passes increased. However, by increasing the rolling passes, the measured thermal capacity values modestly increased while the thermal expansion values first decreased and then increased. Regarding composites, all thermal features decreased with an increase in Ni volume fraction. Due to the restricting effect of harder reinforcement layers, the measured thermal expansion declined from 17.01 × 10−6 1/k in Al/0.2 Vf Ni to 15.4 × 10−6 1/k in Al/0.8 Vf Ni.

Mechanically strong, healable, and recyclable supramolecular solid–solid phase change materials with high thermal conductivity for thermal energy storage

Conventional polymeric solid–solid phase change materials (SSPCMs) have garnered significant attention in the development of state-of-the-art latent heat storage (LHS) systems. However, the industrial application of polymeric SSPCMs is compromised by inferior mechanical properties and intrinsic low thermal conductivity. In addition, they are unable to be recycled and self-healed due to permanently cross-linked structures. In this study, a series of healable and recyclable supramolecular SSPCMs (PEG4K-Bx-PEG6K), possessing robust tensile strength (∼22.90 MPa), excellent strain-at-break (∼733.62 %), and high toughness (∼120.05 MJ/m3), are designed and developed by incorporating dynamic boroxines and hydrogen bonds. Because of the reversibility of dynamic boroxines and hydrogen bonds, the PEG4K-Bx-PEG6K was able to be healable and conveniently processed into packaging bag. More importantly, the PEG4K-Bx-PEG6K also possessed high thermal storage capacity (98.03 J/g), and excellent thermal shape memory capability. To achieve efficient heat transfer, an orientated solar thermal composite with high thermal conductivity was fabricated by compression-induced repetitive stacking of oriented graphene nanosheets (GNs) layers in PEG4K-Bx-PEG6K. Thanks to the efficient heat conduction of oriented GNs layers in the composite, the directional thermal conductivity of composite was up to 3.639 W/mK at 5 wt% loading of GNs. Combining the above excellent heat conduction, the solar thermal composite developed in this work offered efficient solar thermal conversion, fast transportation and storage of the harvested thermal energy.

Weathering resistance of novel sustainable prefabricated thermal insulation wall

External walls, serving as the primary medium for heat exchange between the building and the external environment, has its thermal loss comprising the largest proportion of building energy consumption. Therefore, enhancing the thermal insulation capacity of the wall is of great significance in reducing building energy consumption. In this paper, a novel sustainable prefabricated expanded polystyrene (EPS) thermal insulation wall panel with irregular column frame structures was developed. And weathering tests combined with finite element simulations were conducted to investigate its weathering performance and degradation patterns. The results revealed that In the weathering test, the panel surfaces did not exhibit apparent water seepage cracks, powdering, hollowing, peeling, etc. There was no occurrence of facing brick detachment or damage. The outer surface concrete of the wall panel experienced resistance during normal thermal expansion and contraction, generating compressive stress during expansion and tensile stress when contracted. In addition, the bond strength of the specimens decreased by 8.1% after the thermal-rain cycles, 5.1% after the thermal-cold cycles, and 12.1% after the freeze-thaw cycles. In the numerical simulations, the temperature stress at various positions on the concrete wall had a noticeable mutual restraining effect on the force deformation of the nearby concrete. There was a significant risk of cracking in the middle and around the opening, particularly in the lower part of the wall panel. This study serves as a basis for the degradation analyses and optimization design of the sandwich insulation wall panels for sustainability.

Solar-driven high-performance biomass porous carbon for efficient CO2 capture

Temperature swing adsorption (TSA) based on solid adsorbents is an efficient CO2 capture technology, but the temperature swing process is energy-intensive. Utilizing solar energy to regenerate adsorbents during the CO2 swing adsorption process can decrease energy consumption. This work reports a novel high-performance biomass porous carbon for efficient CO2 capture and separation in the solar-driven TSA process. Inspired by the distinctive internal expansion structure of succulents, the adsorbent is synthesized using succulents as precursors with a large specific surface area (1715 m2/g) and high solar absorbance (90.38 %), resulting in high CO2 adsorption capacity and solar thermal conversion capacity. It achieves a remarkable working capacity of 30.94 mg/g at a low desorption temperature (60 °C) in the solar-driven TSA process with a light intensity of 600 W/m2, 80.7 % higher than commercial activation carbon. The proposed biomass porous carbon derived from succulent plants has substantial potential for application in the solar-driven TSA process.

Nanoengineering-Enhanced Capillary Cooling Achieves Sustained Thermal Protection for Ultra-High Heat Flux and Temperature.

Extreme thermal conditions with heat flux densities exceeding 1 MW·m-2 or temperatures reaching up to 1000 °C are prevalent in various situations. However, the ability of thermal protection either depends on specialized materials or is currently limited with existing cooling schemes. Herein, we propose an innovative cooling scheme that relies on evaporation-driven capillary flow enhanced by nanoengineering-designed porous structures with common materials. Experimentally-obtained capillary flow cooling curve identifies critical heat flux corresponding to evaporation-driven flow stage, where coolants cool the surface and subsequent vapor impedes heat transfer from thermal boundaries. Nanoengineering provides opportunities for enhanced capillary flow, which proves to endow bronze, TC4, and Al2O3 with thermal protection ability 50%-180% higher than that without nanoengineering-designed. Our scheme achieves critical heat flux up to 2.0-3.1 MW·m-2, and performs thermal dissipation capacity almost twice higher than inherent latent heat of coolant. Furthermore, in a supersonic wind tunnel with total temperature reaching up to 1792 K, our scheme effectively protects surfaces by cooling them to surface temperatures below 500 K. Nanoengineering-enhanced capillary cooling gives access to the application of common materials for high-temperature and high-heat-flux environments and paves the way for the development of lightweight, long-lasting, and large-scale solutions for thermal protection. This article is protected by copyright. All rights reserved.

Open-source simulation platform for air source heat pump integrated with thermal energy storage

This article introduces a modular simulation platform for assessing thermal energy storage (TES) integrated with air source heat pumps (ASHP). The Python platform is an open-source library that includes classes for modeling air-air and air-water heat pumps, TES devices, and the heating load of residential buildings. To validate the ASHP model, the study utilized experimental data obtained from a commercial heat pump evaluated at the National Renewable Energy Laboratory (NREL). The results indicate a mean deviation of 0.7% for COP across the operating range, with a maximum relative deviation of 12.6%. In terms of system heating capacity, the model had an average deviation of 4.3% compared to experimental results, with a maximum deviation of 8.2%. Three classes were implemented for modeling distinct types of TES devices: a generic TES based on energy balances, a sensible isothermal water tank, and a stratified water tank. Details of the mathematical models are provided, along with their respective strengths and limitations. An example is provided showcasing the integration of a residential 10 kWh thermal storage unit with an ASHP operating in Denver, CO. The comparison of two different discharge criteria for the TES unit highlights the importance of control strategies in the system performance.

Thermal-Responsive Smart Windows with Passive Dimming and Thermal Energy Storage.

Chromogenic smart windows are one of the key components in improving the building energy efficiency. By simulation of the three-dimensional network of polymer hydrogels, thermal-responsive phase change materials (TRPCMs) are manufactured for energy-saving windows. For simulated polymer hydrogels, tetradecanol (TD) and a color changing dye (CCD) are filled in situ in poly(n-butyl isobutyrate) (PBB) networks. TRPCMs convert solar energy into thermal energy through a dark blue CCD. The TD phase change material (PCM) absorbs heat energy to become a transparent liquid. Simultaneously, the CCD changes from blue to colorless and transparent at around 45 °C. As a result, as-prepared TRPCMs transform from an opaque state at room temperature to a high-transparency state after melting (74.5%). TRPCMs also show a good thermal storage capacity, with a phase transition enthalpy exceeding 161.9 J g-1. As-prepared smart materials can simultaneously achieve photothermal conversion, thermal energy diffusion, latent heat storage, and resistance to liquid leakage at the phase interface between opaque and transparent states, providing more options for the design of energy-saving buildings.

Thermal storage cementitious materials containing SiO2-coated cenosphere@bio-based PCMs: Microstructural, mechanical, and thermal properties

Integration of phase change materials (PCMs) into buildings contributes to mitigating indoor temperature fluctuations, offering opportunities for alleviating energy crisis. However, prevalent PCM integration methods commonly suffer from shortcomings in mechanical properties, compatibility, and environmental sustainability, restricting their applications. This study developed a novel shape-stabilized PCM (SSPCM) using cenospheres from coal-fired power waste and bio-based PCMs from vegetable oil by-products, subsequently sealed with silica coatings to inhibit PCM leakage and improve thermal stability, termed as SCS@PCM, exhibiting melting enthalpy up to 103.9 J/g. SCS@PCM was then integrated into cement mortars by replacing fine sand to fabricate thermal storage cement-based materials (TSCM), followed by assessments of their microstructural, mechanical, and thermal properties. The results showed that the silica coating helps to lowrer adverse impact of SCS@PCM on the compressive strength and thermal conductivity of TSCM. TSCM containing 30.0 vol% SCS@PCM reached a 28-day compressive strength of 45.3 MPa, exhibiting only a 17.4 % reduction compared to the control group, notably less than reductions observed for other SSPCMs reported in literature. Moreover, integration of SCS@PCM improved thermal storage capacities and decreased thermal fluctuation rates of TSCM, evidenced by a 4.7 ℃ decrease in peak temperature at dosage of 30.0 vol%. This study endeavors to develop an eco-friendly TSCM with excellent thermal and mechanical properties, providing insights for applications in improving the thermal regulation and energy efficiency in building roofs.

Precise integration boundary element method for solving nonlinear transient heat conduction problems with temperature dependent thermal conductivity and heat capacity

The precise integration boundary element method (PIBEM) is used to solve nonlinear transient heat conduction problems with temperature dependent thermal conductivity and heat capacity in this article. At first, a boundary-domain integral equation can be obtained by using the fundamental solution for steady linear heat conduction problems. Secondly, the domain integrals are converted into boundary integrals by using the radial integration method to get a pure boundary integral equation, which can retain the advantage of dimension reduction of the boundary element method. Then, after discretization, a first-order nonlinear differential equation system in time is obtained, and the precise integration method with predictor-corrector technique is used to solve the system of nonlinear equations. In the end, several numerical examples are presented to verify the accuracy and stability of the presented method. The results obtained by the presented method are less affected by the time step size and satisfactory results can be obtained even for a large time step size.

Multi-objective optimization and evaluation of the building-integrated photovoltaic/thermal-energy pile ground source heat pump system

Building integrated photovoltaic thermal (BIPV/T)-energy pile ground source heat pump (GSHP) system effectively maintains the soil thermal balance and improves the photovoltaic efficiency by recovering the waste solar heat from the BIPV/T collector to charge the ground. However, due to the strict carbon emission restriction and economic consideration for system application, multi-objective optimization should be implemented for the system design to further enhance its overall performance. Therefore, a complete optimization framework is proposed in this paper, which is based on the NSGA-II algorithm and functions by coupling TRNSYS and jEPlus+EA. Using the proposed optimization frame, a comprehensive optimization is conducted for the system, which optimizes five main design variables and adopts the total power consumption (TPC), life cycle climate performance (LCCP), and life cycle cost (LCC) to reflect the system's energetic, environmental, and economic performances. Seven optimization cases are included in the optimization project to identify design schemes that meet all possible proposed performance requirements for the system application. The optimized results show that the system optimization improves its performance greatly compared to the design condition, with a range of 38.03% ∼ 50.05% for the TPC, 24.52% ∼ 25.86% for LCCP, and 56.74% ∼ 61.66% for LCC. The energetic, environmental and economic performances of the system can be maximized by minimizing the TPC to 357.29 MWh in Case 1, LCCP to 596.15 tCO2 in Case 2, and LCC to 17.03 × 104 CNY in Case 3. By breaking down the objective functions, it is found that the heat pump unit holds paramount importance in all aspects of system performance, and the BIPV/T collector proves advantageous in enhancing the system's long-term performance due to its massive electricity generation. Accordingly, one important finding is that it is advisable to incorporate as many BIPV/T collectors as feasible while maintaining soil heat balance. The optimal energy pile number varies among the seven optimization cases, resulting in different heating capacities for the heat pump unit. Research outcomes in this work offer references for designing the energy-pile GSHP system to enhance the penetration of renewable energy into buildings.

Model Optimization of Ice Melting of Bridge Pylon Crossbeams with Built-In Carbon Fiber Electric Heating

This paper aims to improve the deicing performance and energy utilization of bridge pylon crossbeams with built-in carbon fiber electric heating (BPB–CFEH). Therefore, a three-dimensional thermal transfer model of BPB–CFEH with one arrangement is established. Two ice-melting regions and two ice-melting stages were set up according to the characteristics of the icing of the crossbeam. The effects of wind speed and ambient temperature on the paving power required to reach the complete melting of the icicles within 8 h were analyzed. The effects of the laying spacing and rated voltage of the carbon fiber heating cable on the melting ice sheet and the thermal exchange of the two regions of the icicle after heating for 8 h were compared. Additionally, its effect on energy utilization of the process from the ice sheet melting stage to the ice column melting stage was analyzed. Ice-melting experiments verified the applicability and reasonableness of the simulated ice-melting calculation formula. The results show that under ambient temperature of −10 °C and wind speed of 4.5–13.5 m/s, the proposed paving power is 817.5–2248.12 W/m2. Increasing the rated voltage and shortening the spacing increases the thermal exchange capacity of the two melting regions. The shortening of the spacing improves the energy utilization rate of the melting stage of the ice sheet to the melting stage of the icicle processes. The difference between the melting time obtained from the formula proposed by numerical simulation and the melting time obtained from indoor tests is about 10 min. This study provides a design basis for the electrothermal ice melting of bridge pylon crossbeams.

Thermal performance assessment of the dynamic rotating latent-energy-storage envelope (DRLESE) during winter

The conventional latent-energy-storage-envelope relies solely on the phase changes of Phase-Change Materials (PCMs) to regulate heat transfer, thereby lacking the effectiveness in active indoor heating or cooling. To overcome this technical barrier, the Dynamic Rotating Latent-Energy-Storage Envelope (DRLESE) was proposed to achieve active indoor heating by rotating the PCM layer. The DRLESE can absorb solar gain efficiently and release thermal energy directly indoors. In order to assess the application efficiency of DRLESE, two high-insulation walls incorporating a PCM layer were constructed, with the static one serving as a reference. A numerical heat transfer method was employed and verified an experiment. The numerical results demonstrated that compared to the Static Latent-Energy-Storage Envelope (SLESE), the DRLESE system can release stored thermal energy directly indoors by rotating the PCM layer near the interior, resulting in a released heat flow ranging from −22W/m2 to −80W/m2. However, due to differences in the heat release environment, DRLESE exhibits a lower thermal release rate leading to a reduction of up to 33.8 %∼34.8 % in its thermal release and storage capacity. The DRLESE not only limits thermal dissipation from outdoors but also provides indoor heating, while it provides the thermal energy per unit area to minimize the cooling load of the SLESE with 10.39 m2∼14.10 m2. Finally, it is identified on the present deficiencies and limitations for further the comprehensive investigations.