Theoretical Capacity Research Articles

Ga-polymer dual interfacial layer modified Li metal for high-energy Li metal batteries

Lithium metal is regarded as the ultimate anode material for its extremely exceptional theoretical capacity and low reduction potential. Unfortunately, its practical utility has been constrained by changings such as the formation of lithium dendrites, volume expansion resulting from host-free structure, and uncontrollable side reactions with electrolyte. To achieve long cycle life, conventional single artificial layer strategy fails to solve due to ununiform lithium deposition problem. Consequently, the adoption of dual interfacial layer on lithium metal has emerged as prevailing strategy. In this study, we present a design of dual interface protective layer that combines a Ga-based liquid metal with the organic polymer Poly (ethylene glycol) diacrylate (PEGDA). This innovative combination offers synergistic benefits, including alleviate the volume effect and suppressing undesired interface side reactions. In practical test, the Li || Li symmetrical cell assembled from PEGDA LiGa dual interfacial layer maintains a low overpotential of 36.8 mV after 1400 h (2 mA cm−2, 2mAh cm−2). Moreover, even at a high rate of 5C, Li || LiNi0.8Co0.1Mn0.1O2 (NCM811, 1.0 mAh cm−2) cell still delivers a discharge capacity of 120 mAh g−1, 1.4 times higher than bare Li. Notably, when integrated into a pouch cell with a LiNi0.6Co0.2Mn0.2O2 (NCM622) cathode (1.52 mAh cm−2), this dual interface layers ensures stable performance over 60 cycles, with a capacity retention of 82 %. In summary, this innovative dual interface layer design offers a promising approach to address the intricate challenges associated with lithium metal protection and interface modification.

Mo4/3B2Tx induced hierarchical structure and rapid reaction dynamics in MoS2 anode for superior sodium storage

Molybdenum sulfide (MoS2) with large layer distance and high theoretical capacity has been identified as one of the most promising anodes for sodium ion batteries, but the poor intrinsic conductivity and severe structural agglomeration restricted its diffusion kinetic and specific capacity. In this work, the synergistic effect of heterogeneous interface and Na2S adsorption/conversion active sites was employed to construct Mo4/3B2Tx-MoS2@C composites using a self-assembly and calcination strategy. Theoretical calculation and experimental results demonstrated that the charge transfer and interface between Mo4/3B2Tx and MoS2 along with the 3D hydrangea-like structure improved the intrinsic conductivity and provided fast ion diffusion channels, boosting the electrochemical kinetics; while the favorable adsorption of Na2S and weakened Na-S bond at Mo4/3B2Tx-Mo interface optimized the recombination energies of Mo-S bond, accelerating the ion diffusion and enhancing the electrochemical reversibility. In addition, the copious sulfur vacancies provided additional active sites for ion storage, ameliorating the electrochemical capacity. As expected, the novel Mo4/3B2Tx-MoS2@C electrode delivered a satisfactory rate capacity (340.6 mAh g−1 at 1 A g−1) and durable cyclic performance (267.2 mAh g−1 after 600 cycles at 2 A g−1). When paring with Na3V2(PO4)3, the Mo4/3B2Tx-MoS2@C||Na3V2(PO4)3 full cell exhibited high energy densities of 234.0 and 131.7 Wh kg−1 at 215.7 W kg−1 and 4.4 kW kg−1, respectively. The proposed synergistic strategy of heterogeneous interface and Na2S adsorption/conversion active sites provided a new guidance for the rational design of transitional metal sulfide anodes for sodium ion batteries.

Enhancing Performance and Longevity of Solid-State Zinc-Iodine Batteries with Fluorine-Rich Solid Electrolyte Interphase

Abstract Rechargeable zinc-iodine (ZnI2) batteries have gained popularity within the realm of aqueous batteries due to their inherent advantages, including natural abundance, intrinsic safety, and high theoretical capacity. However, challenges persist in their practical applications, notably battery swelling and vulnerability in aqueous electrolytes, primarily linked to the hydrogen evolution reaction and zinc dendrite growth. To address these challenges, this study presents an innovative approach by designing an all-solid-state ZnI2 battery featuring a solid perfluoropolyether (PFPE)-based polymer electrolyte. The results demonstrate the formation of a solid electrolyte interphase (SEI) layer on zinc, promoting horizontal zinc growth, mitigating dendrite penetration, and enhancing battery cycle life. Moreover, the solid electrolyte hinders the iodine ion shuttle effect, reducing zinc foil corrosion. Symmetric batteries employing this electrolyte demonstrate excellent cycle performance, maintaining stability for approximately 5000 hours at room temperature, while all-solid-state ZnI2 batteries exhibit over 7000 cycles with a capacity retention exceeding 72.2%. This work offers a promising pathway to achieving reliable energy storage in solid-state ZnI2 batteries and introduces innovative concepts for flexible and wearable zinc batteries.

Facile Fabrication of Large-Area CuO Flakes for Sodium-Ion Energy Storage Applications

CuO is recognized as a promising anode material for sodium-ion batteries because of its impressive theoretical capacity of 674 mAh g−1, derived from its multiple electron transfer capabilities. However, its practical application is hindered by slow reaction kinetics and rapid capacity loss caused by side reactions during discharge/charge cycles. In this work, we introduce an innovative approach to fabricating large-area CuO and CuO@Al2O3 flakes through a combination of magnetron sputtering, thermal oxidation, and atomic layer deposition techniques. The resultant 2D CuO flakes demonstrate excellent electrochemical properties with a high initial reversible specific capacity of 487 mAh g−1 and good cycling stability, which are attributable to their unique architectures and superior structural durability. Furthermore, when these CuO flakes are coated with an ultrathin Al2O3 layer, the integration of the 2D structures with outer nanocoating leads to significantly enhanced electrochemical properties. Notably, even after 70 rate testing cycles, the CuO@Al2O3 materials maintain a high capacity of 525 mAh g−1 at a current density of 50 mA g−1. Remarkably, at a higher current density of 2000 mA g−1, these materials still achieve a capacity of 220 mAh g−1. Moreover, after 200 cycles at a current density of 200 mA g−1, a high charge capacity of 319 mAh g−1 is sustained. In addition, a full cell consisting of a CuO@Al2O3 anode and a NaNi1/3Fe1/3Mn1/3O2 cathode is investigated, showcasing remarkable cycling performance. Our findings underscore the potential of these innovative flake-like architectures as electrode materials in high-performance sodium-ion batteries, paving the way for advancements in energy storage technologies.

High Safety Electrolyte Design for Enabling High Energy-Density System of LiNi0.8Co0.1Mn0.1O2//Phosphorus by Simultaneously Adjusting Dual Electrode/Electrolyte Interfaces.

The demand for state-of-the-art high-energy-density lithium-ion batteries is increasing. However, the low specific capacity of electrode materials in conventional full-cell systems cannot meet the requirements. Ni-rich layered oxide cathodes such as Li(Ni0.8Co0.1Mn0.1)O2 (NCM811) have a high theoretical specific capacity of 200 mAh g-1, but it is always accompanied by side reactions on the electrode/electrolyte interface. Phosphorus anode possesses a high theoretical specific capacity of 2596 mAh g-1, but it has a huge volume expansion (≈300%). Herein, a highly compatible and secure electrolyte is reported via introducing an additive with a narrow electrochemical window, Lithium difluoro(oxalato)borate (LiDFOB), into 1m LiPF6 EC/DMC with tris (2,2,2-trifluoroethyl) phosphate (TFEP) as a cosolvent. LiDFOB participates in the formation of organic/inorganic hybrid electrode/electrolyte interface layers at both the cathode and anode sides. The side reactions on the surface of the NCM811 cathode and the volume expansion of the phosphorus anode are effectively alleviated. The NCM811//RP full cell in this electrolyte shows high capacity retention of 82% after 150 cycles at a 0.5C rate. Meanwhile, the electrolyte shows non-flammability. This work highlights the importance of manipulating the electrode/electrolyte interface layers for the design of lithium-ion batteries with high energy density.

Mechanochemically Robust LiCoO2 with Ultrahigh Capacity and Prolonged Cyclability.

Pushing intercalation-type cathode materials to their theoretical capacity often suffers from fragile Li-deficient frameworks and severe lattice strain, leading to mechanical failure issues within the crystal structure and fast capacity fading. This is particularly pronounced in layered oxide cathodes because the intrinsic nature of their structures is susceptible to structural degradation with excessive Li extraction, which remains unsolved yet despite attempts involving elemental doping and surface coating strategies. Herein, we develop a mechanochemical strengthening strategy through gradient disordering structure to address these challenges and push the LiCoO2 layered cathode approaching the capacity limit (256 mAh g-1, up to 93% of Li utilization). This innovative approach also demonstrates exceptional cyclability and rate capability, as validated in practical Ah-level pouch full cells, surpassing the current performance benchmarks. Comprehensive characterizations with multiscale X-ray, electron diffraction and imaging techniques unveil that the gradient disordering structure notably diminishes the anisotropic lattice strain and exhibits high fatigue resistance, even under extreme delithiation states and harsh operating voltages. Consequently, our designed LiCoO2 cathode impedes the growth and propagation of particle cracks, and mitigates irreversible phase transitions. This work sheds light on promising directions towards next-generation high-energy-density battery materials through structural chemistry design. This article is protected by copyright. All rights reserved.

Boosting the Electrochemi,cal Performance of Primary and Secondary Lithium Batteries with Mn-Doped All-Fluoride Cathodes.

Transition metal fluorides are potentially high specific energy cathode materials of next-generation lithium batteries, and strategies to address their low conductivity typically involve a large amount of carbon coating, which reduces the specific energy of the electrode. In this study, MnyFe1-yF3@CFx was generated by the all-fluoride strategy, converting most of the carbon in MnyFe1-yF3@C into electrochemical active CFx through a controllable NF3 gas phase fluorination method, while still retaining a tightly bound graphite layer to provide initial conductivity, which greatly improved the energy density of the composite. This synergistic effect of nonfluorinated residual carbon (∼11%) and Mn doping ensures the electrochemical kinetics of the composite. The loading mass of the active substance had been increased to 86%. The theoretical and actual discharge capacity of MnyFe1-yF3@CFx composite was up to 765 mAh g-1 (pure FeF3 is 712 mAh g-1) and 728 mAh g-1, respectively. The discharge capacity at the high-voltage (3.0 V) platform was more than three times higher than that of the non-Mn-doped composite (FeF3@CFx).

Novel design of Sn4P3@NxC electrodes and their electrochemical properties

Tin phosphide (SnxPy) is recognized as one of the most promising anode materials for lithium-ion batteries due to its exceptionally high theoretical capacity. However, its application is hampered by significant volume expansion during charge-discharge cycles and inferior electrical conductivity. Proper structural design placs a pivotal role in addressing these challenges, paving the way for high-performance anode materials. This study introduces a nitrogen-doped carbon-coated Sn4P3 nanosphere with a core-shell structure, employing dopamine as the nitrogen source. This innovative approach, utilizing template removal and solid-phase phosphorization, results in both the core and shell acting as active materials, thereby enhancing the volumetric energy density of the electrode. The internal voids within the shell layer mitigate volume expansion during charge-discharge cycles, while the presence of the nitrogen-doped carbon layer maintains the material's stability throughout cycling and improves its electrical conductivity. Electrochemical performance tests confirm the outstanding energy storage capability of this material, with an initial Coulombic efficiency reaching up to 73.6 %. Furthermore, it maintains a stable capacity of 585 mAh g^-1 after 1200 cycles at a current density of 2 A g^-1. This research offers a design paradigm for the development of novel energy storage materials.

Anchored VN Quantum Dots Boosting High Capacity and Cycle Durability of Na3V2(PO4)3@NC Cathode for Aqueous Zinc-Ion Battery and Organic Sodium-Ion Battery.

Na3V2(PO4)3 is a promising high-voltage cathode for aqueous zinc-ion batteries (ZIBs) and organic sodium-ion batteries (SIBs). However, the poor rate capability, specific capacity, and cycling stability severely hamper it from further development. In this work, Na3V2(PO4)3 (NVP) with vanadium nitride (VN) quantum dots encapsulated by nitrogen-doped carbon (NC) nanoflowers (NVP/VN@NC) are manufactured as cathode using in situ nitridation, carbon coating, and structural adjustment. The outer NC layer increases the higher electronic conductivity of NVP. Furthermore, VN quantum dots with high theoretical capacity not only improve the specific capacity of pristine NVP, but also serve as abundant "pins" between NVP and NC to strengthen the stability of NVP/VN@NC heterostructure. For Zn-ion storage, these essential characteristics allow NVP/VN@NC to attain a high reversible capacity of 135.4mAhg-1 at 0.1Ag-1, and a capacity retention of 91% after 2000 cycles at 5Ag-1. Meanwhile, NVP/VN@NC also demonstrates to be a stable cathode material for SIBs, which can reach a high reversible capacity of 124.5mAhg-1 at 0.1Ag-1, and maintain 92% of initial capacity after 11000 cycles at 5Ag-1. This work presents a feasible path to create innovative high-voltage cathodes with excellent reaction kinetics and structural stability.

Synergetic Dual-Additive Electrolyte Enables Highly Stable Performance in Sodium Metal Batteries.

Sodium (Na)-metal batteries (SMBs) are considered one of the most promising candidates for the large-scale energy storage market owing to their high theoretical capacity (1,166 mAh g-1) and the abundance of Na raw material. However, the limited stability of electrolytes still hindered the application of SMBs. Herein, sulfolane (Sul) and vinylene carbonate (VC) are identified as effective dual additives that can largely stabilize propylene carbonate (PC)-based electrolytes, prevent dendrite growth, and extend the cycle life of SMBs. The cycling stability of the Na/NaNi0.68Mn0.22Co0.1O2 (NaNMC) cell with this dual-additive electrolyte is remarkably enhanced, with a capacity retention of 94% and a Coulombic efficiency (CE) of 99.9% over 600 cycles at a 5 C (750mA g-1) rate. The superior cycling performance of the cells can be attributed to the homogenous, dense, and thin hybrid solid electrolyte interphase consisting of F- and S-containing species on the surface of both the Na metal anode and the NaNMC cathode by adding dual additives. Such unique interphases can effectively facilitate Na-ion transport kinetics and avoid electrolyte depletion during repeated cycling at a very high rate of 5 C. This electrolyte design is believed to result in further improvements in the performance of SMBs.

Theoretical investigation of NbB as an electrode material for Li/Na-ion batteries

The utilization of MBenes as electrode materials for lithium/sodium-ion batteries (LIBs/NIBs) has emerged as a prominent research area. The potential application of two-dimensional niobium boride (NbB) in LIBs/NIBs was explored through first-principles calculations. The results indicate that the monolayer of NbB exhibits exceptional dynamic stability, thermodynamic stability and electrical conductivity. The migration path of Li/Na on the NbB surface was determined, revealing diffusion barriers as low as 0.034 and 0.017 eV respectively, indicating the exceptional mobility and reversibility exhibited by NbB. The theoretical capacities of Li and Na on NbB are 258 and 323 mAh g−1, respectively. The open circuit voltage (OCV) varies within the range of 0.58 to 0.71 V and 0.05 to 0.81 V for Li/Na concentrations. Meanwhile, the investigation into the influence of various functional groups of NbB on the adsorption properties of Li/Na atoms reveals that both NbBO and NbBS surfaces retain their maximum capacity for Li/Na adsorption, whereas the NbBSe surface fails to achieve complete layer adsorption of Li/Na atoms. The introduction of the S functional groups not only maintains the ultra-low diffusion barrier (0.09 eV) of Na ions but also results in a significant decrease in the average OCV of Li/Na adsorption, which is approximately 0.37 and 0.14 V, respectively. The electrochemical properties of NbB in LIBs/NIBs are exceptional, positioning it as a promising electrode material within the MBenes family.

Investigation of cathode properties of two-dimensional NbS2Cl2 for Li and Na-ion batteries using density functional theory

Exploring novel two-dimensional materials (2D) for electrode and electrochemical storage applications stands as a pivotal pursuit in advancing renewable energy technologies. While recent research has predominantly focused on anode materials, cathode materials have received comparatively lesser attention. This study delves into the potential cathode applications of the novel two-dimensional material NbS2Cl2 using density functional theory. Fundamental properties, encompassing electronic and thermodynamic attributes, were scrutinized to comprehend the material’s characteristics. Our investigation extended to examining the adsorption and diffusion properties of these electrode materials. Comprehensive calculations of mechanical and thermodynamic properties reaffirmed the stability of this system. Upon adsorption of Li/Na atoms, the conducting nature emerged, evident through charge density difference and projected density of states. Our findings notably reveal minimal diffusion barriers of 1.5 eV and 0.35 eV for Li and Na atoms. Moreover, the observed open circuit voltages for adsorbed Li and Na ions were 4.69 V and 2.62 V, respectively. The calculated theoretical capacity for adsorbed Li-ion on 2D-NbS2Cl2 is 400 mAh g−1, while for Na-ion adsorption, it is 353 mAh g−1, awaiting validation through future experimental verifications.

Additive-Free Anode with High Stability: Nb2CTx MXene Prepared by HCl-LiF Hydrothermal Etching for Lithium-Ion Batteries.

MXenes, represented by Ti3C2Tx, have been widely studied in the electrochemical energy storage fields, including lithium-ion batteries, for their unique two-dimensional structure, tunable surface chemistry, and excellent electrical conductivity. Recently, Nb2CTx, as a new type of MXene, has attracted more and more attention due to its high theoretical specific capacity of 542 mAh g-1. However, the preparation of few-layer Nb2CTx nanosheets with high-quality remains a challenge, which limits their research and application. In this work, high-quality few-layer Nb2CTx nanosheets with a large lateral size and a high conductivity of up to 500 S cm-1 were prepared by a simple HCl-LiF hydrothermal etching method, which is 2 orders of magnitude higher than that of previously reported Nb2CTx. Furthermore, from its aqueous ink, the viscosity-tunable organic few-layer Nb2CTx ink was prepared by HCl-induced flocculation and N-methyl-2-pyrrolidone treatment. When using the organic few-layer Nb2CTx ink as an additive-free anode of lithium-ion batteries, it showed excellent cycling performance with a reversible specific capacity of 524.0 mAh g-1 after 500 cycles at 0.5 A g-1 and 444.0 mAh g-1 after 5000 cycles at 1 A g-1. For rate performance, a specific capacity of 159.8 mAh g-1 was obtained at a high current density of 5 A g-1, and an excellent capacity retention rate of about 95.65% was achieved when the current density returned to 0.5 A g-1. This work presents a simple and scalable process for the preparation of high-quality Nb2CTx and its aqueous/organic ink, which demonstrates important application potential as electrodes for electrochemical energy storage devices.

Ball Milling Innovations Advance Mg-Based Hydrogen Storage Materials Towards Practical Applications

Mg-based materials have been widely studied as potential hydrogen storage media due to their high theoretical hydrogen capacity, low cost, and abundant reserves. However, the sluggish hydrogen absorption/desorption kinetics and high thermodynamic stability of Mg-based hydrides have hindered their practical application. Ball milling has emerged as a versatile and effective technique to synthesize and modify nanostructured Mg-based hydrides with enhanced hydrogen storage properties. This review provides a comprehensive summary of the state-of-the-art progress in the ball milling of Mg-based hydrogen storage materials. The synthesis mechanisms, microstructural evolution, and hydrogen storage properties of nanocrystalline and amorphous Mg-based hydrides prepared via ball milling are systematically reviewed. The effects of various catalytic additives, including transition metals, metal oxides, carbon materials, and metal halides, on the kinetics and thermodynamics of Mg-based hydrides are discussed in detail. Furthermore, the strategies for synthesizing nanocomposite Mg-based hydrides via ball milling with other hydrides, MOFs, and carbon scaffolds are highlighted, with an emphasis on the importance of nanoconfinement and interfacial effects. Finally, the challenges and future perspectives of ball-milled Mg-based hydrides for practical on-board hydrogen storage applications are outlined. This review aims to provide valuable insights and guidance for the development of advanced Mg-based hydrogen storage materials with superior performance.

Pressure‐Induced Dense and Robust Ge Architecture for Superior Volumetric Lithium Storage

AbstractThe germanium (Ge) anode attains wide attention in lithium‐ion batteries because of its high theoretical volumetric capacity (8646 mAh cm−3). However, the huge volume expansion (≈230%) results in its poor electrochemical performances. The strategies reported in the literature to solve the issue often cause a low packing density, lowering the volumetric capacity. Here, a pressure‐induced route is proposed to fabricate a Ge architecture, in which nano‐sized Ge (≈15 nm) is encapsulated by robust TiO2 and highly conductive carbon, which offer the advantages of a low stress–strain characteristic, low volume expansion in thickness change, high electrical conductivity (463.2 S m−1), high Li‐ion diffusion coefficient (9.55 × 10−9–8.51 × 10−12 cm2 s−1), and high tapping density (1.79 g cm−3). As a result, the dense architecture obtains outstanding volumetric capacities of 3559.8 mAh cm−3 at 0.1 A g−1 and 2628.2 mAh cm−3 at 20 A g−1, along with excellent cycling life over 5000 cycles at 10 A g−1. Remarkably, the full cell achieves a high volumetric energy density of 1760.1 Wh L−1, along with impressive fast‐charging performances and long cycling life. This work provides a new synthesis strategy and deep insight into the design of high‐volumetric capacity alloy‐based lithium‐ion‐battery anodes.

Assembled MXene-Liquid Metal Cages on Silicon Microparticles as Self-Healing Battery Anodes.

In pursuit of higher energy density in lithium-ion batteries, silicon (Si) has been recognized as a promising candidate to replace commercial graphite due to its high theoretical capacity. However, the pulverization issue of Si microparticles during lithiation/delithiation results in electrical contact loss and increased side reactions, significantly limiting its practical applications. Herein, we propose to utilize liquid metal (LM) particles as the bridging agent, which assemble conductive MXene (Ti3C2Tx) sheets via coordination chemistry, forming cage-like structures encapsulating mSi particles as self-healing high-energy anodes. Due to the integration of robust Ti3C2Tx sheets and deformable LM particles as conductive buffering cages, simultaneously high-rate capability and cyclability can be realized. Post-mortem analysis revealed the cage structural integrity and the maintained electrical percolating network after cycling. This work introduces an effective approach to accommodate structural change via a resilient encapsulating cage and offers useful interface design considerations for versatile battery electrodes.

First-principles study of high-entropy sulfides and their alkali metal-doped modification as cathode material for sodium-ion batteries.

High-entropy materials (HEMs) have been explored as high-capacity cathode materials for sodium-ion batteries (SIBs) due to their excellent structural stability and abundant metal redox sites. Among them, high-entropy sulfides (HESs) have greater potential and more extensive research than high-entropy oxides, as they exhibit higher charging voltage and theoretical capacity as cathodes. Furthermore, alkali metal doping of HESs can further enhance their performance and broaden their application fields. Inspired by the cocktail effect of HEMs, we performed the first theoretical calculation of the properties of Na(MnFeCoNi)1/2S and its Li-doped derivative, Na7/8Li1/8(MnFeCoNi)1/2S, to understand their potential as SIB cathode materials. Using density functional theory based on first principles, we investigated the structure and electronic characteristics of Na(MnFeCoNi)1/2S and Na7/8Li1/8(MnFeCoNi)1/2S, and calculated their theoretical voltage and capacity, respectively. Compared with Na(MnFeCoNi)1/2S, Na7/8Li1/8(MnFeCoNi)1/2S showed better electronic performance in reducing the band gap and increasing the density of states, ultimately providing a specific capacity of 160.3 mAh·g-1 and a charging voltage of 4.85 V in sodium-ion storage. Moreover, Na7/8Li1/8(MnFeCoNi)1/2S exhibited remarkable structural stability throughout the sodium-ion deintercalation process, thus it can be reasonably concluded that Na7/8Li1/8(MnFeCoNi)1/2S can serve as an excellent cathode material for future SIB applications.

Impact of LaZnFe2O4 supported NiWO4@D400-MMT@CMS/MMA nanocomposites as a catalytic system in remediation of dyes from wastewater

Herein, a novel nanocomposite based on lanthanum zinc ferrite and nickel tungstate was created by incorporation between (MMT-jeffamine-400) nanoparticles (NPs), chloromethyl styrene as a binder and polymethyl methacrylate monomer using solution polymerization. The as-designed nanocomposites were employed to confiscate xylenol orange “X.O” as an acidic dye and rhodamine B “RhB” as “an amphoteric dye” from colored wastewater. The impact of several parameters such as solution pH, initial dye concentration, the effect of time, and the effect of temperature was explored. The consequences indicated that the pure organoclay had negligible adsorption while that composed of organoclay with PMMA@CMS-polymer incorporated with LaZnFe2O4@NiWO4 particles detached more than 90% for xylenol orange (XO) and 93% for “rhodamine B” molecules. Electrostatic interactions are the predominant factor in the adsorption of cationic and amphoteric adsorbates, as proven by zeta-potential measurement. Additionally, the adsorbent may be regenerate and utilized up to five times with good adsorption capabilities by adding sodium hydroxide. As a result, the removal can be effectively accomplished using the nanocomposite as an adsorbent. The actual and theoretical adsorption capacity values for both dyes at all doses were closely matched, which supported the adsorption kinetics data that fit the pseudo-first order rate model well. The adsorption data’s correlation values (0.995 for XO and 0.98 for RhB) indicated that both dyes’ Langmuir adsorption would perform well. Furthermore, the adsorption of XO and RhB dyes on the adsorbent is confirmed to be a viable reaction by the negative values of ΔGo. The enhanced adsorbent material for the removal of amphoteric and anionic dyes from waste water is the synthesized LaZnFe2O4 supported NiWO4@D400-MMT@CMS/MMA nanocomposites, which exhibits a reusability affinity of up to five cycles.

Fast-Charging Phosphorus-Based Anodes: Promises, Challenges, and Pathways for Improvement.

Fast-charging batteries are highly sought after. However, the current battery industry has used carbon as the preferred anode, which can suffer from dendrite formation problems at high current density, causing failure after prolonged cycling and posing safety hazards. The phosphorus (P) anode is being considered as a promising successor to graphite due to its safe lithiation potential, low ion diffusion energy barrier, and high theoretical storage capacity. Since 2019, fast-charging P-based anodes have realized the goals of extreme fast charging (XFC), which enables a 10 min recharging time to deliver a capacity retention larger than 80%. Rechargeable battery technologies that use P-based anodes, along with high-capacity conversion-type cathodes or high-voltage insertion-type cathodes, have thus garnered substantial attention from both the academic and industry communities. In spite of this activity, there remains a rather sparse range of high-performance and fast-charging P-based cell configurations. Herein, we first systematically examine four challenges for fast-charging P-based anodes, including the volumetric variation during the cycling process, the electrode interfacial instability, the dissolution of polyphosphides, and the long-lasting P/electrolyte side reactions. Next, we summarize a range of strategies with the potential to circumvent these challenges and rationally control electrochemical reaction processes at the P anode. We also consider both binders and electrode structures. We also propose other remaining issues and corresponding strategies for the improvement and understanding of the fast-charging P anode. Finally, we review and discuss the existing full cell configurations based on P anodes and forecast the potential feasibility of recycling spent P-based full cells according to the trajectory of recent developments in batteries. We hope this review affords a fresh perspective on P science and engineering toward fast-charging energy storage devices.

Successful In Situ Growth of Conductive MOFs on 2D Cobalt-Based Compounds and Their Electrochemical Performance.

Conductive metal-organic frameworks (cMOFs), as a kind of porous material, are considered to be highly promising materials in the field of electrochemistry due to their excellent conductivity. However, due to the low specific capacitance of pure cMOFs, their application in supercapacitors is limited. By virtue of the high theoretical capacity and excellent chemical stability of Co-based compounds, in this work, cMOFs' M-HHTP (M = Ni, Co, NiCo, HHTP = 2,3,6,7,10,11-hexahydroxytriphenylene) are grown in situ on Co(OH)2, CoP, and Co3O4 nanosheets, resulting in a series of electroactive compounds as electrode materials used in supercapacitors. Among all of the compounds, Ni-HHTP@Co(OH)2 shows the most excellent energy storage performance and outstanding cyclic stability in the application of aqueous asymmetric supercapacitors.