Tethered Bilayer Lipid Membranes Research Articles

Molecular engineering of tethered bilayer lipid membranes for impedimetric detection of pore-forming toxins

Tethered bilayer lipid membranes (tBLMs) with two different molecular architectures were investigated in the context of their utility for biosensing of pore-forming toxins (PFTs). The different architectures were achieved by using two back-filler molecules of different chain length to act as surface diluents for the molecular anchors [20-tetradecyloxy-3,6,9,12,15,18,22-heptaoxahexatricontane-1-thiol (WC14)] that ensure immobilization of the phospholipid bilayers on a solid conductive (metal, such as gold) support. The back-filler molecules were β-mercaptoethanol (BME) and HS(CH2)3(CH2CH2O)5H thiol (C3EO5H). In the case of BME, the submembrane space separating solid surface from attached bilayer (typically 1-2 nm thick) is populated with the ice-like, presumably low entropy and low dielectric constant water, however, the water fraction in the submembrane is high. Much bulkier C3EO5H back-filler renders less space for water in the submembrane, however, it is populated with more mobile water molecules resulting in higher dielectric constant. These two opposing effects result in similar submembrane specific conductances, i.e., the specific electrochemical impedance spectral (EIS) characteristics of the tBLMs and their variation, upon exposure to and reorganization with, the pore-forming toxin (PFT), alpha-hemolysin, occur in the same frequency range for both back-fillers. Significantly, the sensitivity of the C3EO5H-containing tBLMs to PFT is approximately 7–8 times higher than that of the BME-containing surface constructs. At least two physical phenomena contribute to this difference. The bulkier C3EO5H back-fillers facilitate the formation of nanoclusters of the molecular anchors, WC14, with cluster sizes ranging from 20–120 nm. These highly anchor-clustered, “patchy” tBLMs, consequently exhibit other domains devoid, or nearly so, of anchors, resulting in lowering the tBLM global 2-D viscosity by a factor of 3. Thus, a major conclusion of this study is that lower tBLM 2D fluidity increases the sensitivity of tBLMs to PFTs.

Cation Dependence of Enniatin B/Membrane-Interactions Assessed Using Surface-Enhanced Infrared Absorption (SEIRA) Spectroscopy.

Enniatins are mycotoxins with well-known antibacterial, antifungal, antihelmintic and antiviral activity, which have recently come to attention as potential mitochondriotoxic anticancer agents. The cytotoxicity of enniatins is traced back to ionophoric properties, in which the cyclodepsipeptidic structure results in enniatin:cation-complexes of various stoichiometries proposed as membrane-active species. In this work, we employed a combination of surface-enhanced infrared absorption (SEIRA) spectroscopy, tethered bilayer lipid membranes (tBLMs) and density functional theory (DFT)-based computational spectroscopy to monitor the cation-dependence (Mz+=Na+, K+, Cs+, Li+, Mg2+, Ca2+) on the mechanism of enniatin B (EB) incorporation into membranes and identify the functionally relevant EBn : Mz+ complexes formed. We find that Na+ promotes a cooperative incorporation, modelled via an autocatalytic mechanism and mediated by a distorted 2 : 1-EB2 : Na+ complex. K+ (and Cs+) leads to a direct but less efficient insertion into membranes due to the adoption of "ideal" EB2 : K+ sandwich complexes. In contrast, the presence of Li+, Mg2+, and Ca2+ causes a (partial) extraction of EB from the membrane via the formation of "belted" 1 : 1-EB : Mz+ complexes, which screen the cationic charge less efficiently. Our results point to a relevance of the cation dependence for the transport into the malignant cells where the mitochondriotoxic anticancer activity is exerted.

Dimeric peptoids as antibacterial agents

Building upon our previous study on peptoid-based antibacterials which showed good activity against Gram-positive bacteria only, herein we report the synthesis of 34 dimeric peptoid compounds and the investigation of their activity against Gram-positive and Gram-negative pathogens. The newly designed peptoids feature a di-hydrophobic moiety incorporating phenyl, bromo-phenyl, and naphthyl groups, combined with variable lengths of cationic units such as amino and guanidine groups. The study also underscores the pivotal interplay between hydrophobicity and cationicity in optimizing efficacy against specific bacteria. The bromophenyl dimeric guanidinium peptoid compound 10j showed excellent activity against S. aureus 38 and E. coli K12 with MIC of 0.8 μg mL−1 and 6.2 μg mL−1, respectively. Further investigation into the mechanism of action revealed that the antibacterial effect might be attributed to the disruption of bacterial cell membranes, as suggested by tethered bilayer lipid membranes (tBLMs) and cytoplasmic membrane permeability studies. Notably, these promising antibacterial agents exhibited negligible toxicity against mammalian red blood cells. Additionally, the study explored the potential of 12 active compounds to disrupt established biofilms of S. aureus 38. The most effective biofilm disruptors were ethyl and octyl-naphthyl guanidinium peptoids (10c and 10 k). These compounds 10c and 10 k disrupted the established biofilms of S. aureus 38 with 51 % at 4x MIC (MIC = 17.6 μg mL−1 and 11.2 μg mL−1) and 56 %-58 % at 8x MIC (MIC = 35.2 μg mL−1 and 22.4 μg mL−1) respectively. Overall, this research contributes insights into the design principles of cationic dimeric peptoids and their antibacterial activity, with implications for the development of new antibacterial compounds.

Membrane-Disruptive Effects of Fatty Acid and Monoglyceride Mitigants on E. coli Bacteria-Derived Tethered Lipid Bilayers.

We report electrochemical impedance spectroscopy measurements to characterize the membrane-disruptive properties of medium-chain fatty acid and monoglyceride mitigants interacting with tethered bilayer lipid membrane (tBLM) platforms composed of E. coli bacterial lipid extracts. The tested mitigants included capric acid (CA) and monocaprin (MC) with 10-carbon long hydrocarbon chains, and lauric acid (LA) and glycerol monolaurate (GML) with 12-carbon long hydrocarbon chains. All four mitigants disrupted E. coli tBLM platforms above their respective critical micelle concentration (CMC) values; however, there were marked differences in the extent of membrane disruption. In general, CA and MC caused larger changes in ionic permeability and structural damage, whereas the membrane-disruptive effects of LA and GML were appreciably smaller. Importantly, the distinct magnitudes of permeability changes agreed well with the known antibacterial activity levels of the different mitigants against E. coli, whereby CA and MC are inhibitory and LA and GML are non-inhibitory. Mechanistic insights obtained from the EIS data help to rationalize why CA and MC are more effective than LA and GML at disrupting E. coli membranes, and these measurement capabilities support the potential of utilizing bacterial lipid-derived tethered lipid bilayers for predictive assessment of antibacterial drug candidates and mitigants.

Effect of pH on Electrochemical Impedance Response of Tethered Bilayer Lipid Membranes: Implications for Quantitative Biosensing

Tethered bilayer lipid membranes (tBLMs) are increasingly used in biosensor applications where electrochemical impedance spectroscopy (EIS) is the method of choice for amplifying and recording the activity of membrane-damaging agents such as pore-forming toxins or disrupting peptides. While the activity of these biological agents may depend on the pH of the analytes, there is increasing evidence that the sensitivity of tethered bilayer sensors depends on the pH of the solutions. In our study, we addressed the question of what are the fundamental reasons for the variability of the EIS signal of the tBLMs with pH. We designed an experiment to compare the EIS response of tBLMs with natural membrane defects and two different membrane disruptors: vaginolysin and melittin. Our experimental design ensured that the same amount of protein and peptide was present in the tBLMs, while the pH was varied by replacing the buffers with different pH values. Using a recently developed EIS data analysis algorithm from our research group, we were able to demonstrate that, in contrast to previous literature which relates the variability of tBLM, EIS response to the variation in defect density, the main reason for the observed variability in EIS response is the change in the sub-membrane properties of tBLMs with pH. Using surface-enhanced infrared absorption spectroscopy (SEIRAS), we have shown that pH changes from neutral to slightly acidic leads to an expulsion of water, presumably bound to ions, from the sub-membrane reservoir, resulting in a marked decrease in the carrier concentration and specific conductance of the sub-membrane reservoir. Such a decrease is recorded by the EIS as a decrease in the conductance of the tBLM complex and affects the sensitivity of a biosensor. Our data provide important evidence of pH-sensitive effects that should be considered in both the development and operation of biosensors.

Sparsely tethered bilayer lipid membranes formed by self-assembly of bicelles: Spectroelectrochemical characterization and incorporation of transmembrane protein

Many biochemical processes related to proper homeostasis take place in cell membranes. The key molecules involved in these processes are proteins, including transmembrane proteins. These macromolecules still challenge the understanding of their function within the membrane. Biomimetic models that mimic the properties of the cell membrane can help understand their functionality. Unfortunately, preserving the native protein structure in such systems is problematic. A possible solution to this problem involves the use of bicelles. Their unique properties make integrating bicelles with transmembrane proteins manageable while preserving their native structure. Hitherto, bicelles have not been used as precursors for protein-hosting lipid membranes deposited on solid substrates like pre-modified gold. Here, we demonstrated that bicelles can be self-assembled to form sparsely tethered bilayer lipid membranes and the properties of the resulting membrane satisfy the conditions suitable for transmembrane protein insertion. We showed that the incorporation of α-hemolysin toxin in the lipid membrane leads to a decrease in membrane resistance due to pore formation. Simultaneously, the insertion of the protein causes a drop in the capacitance of the membrane-modified electrode, which can be explained by the dehydration of the polar region of the lipid bilayer and the loss of water from the submembrane region.

Unraveling Membrane-Disruptive Properties of Sodium Lauroyl Lactylate and Its Hydrolytic Products: A QCM-D and EIS Study.

Membrane-disrupting lactylates are an important class of surfactant molecules that are esterified adducts of fatty acid and lactic acid and possess industrially attractive properties, such as high antimicrobial potency and hydrophilicity. Compared with antimicrobial lipids such as free fatty acids and monoglycerides, the membrane-disruptive properties of lactylates have been scarcely investigated from a biophysical perspective, and addressing this gap is important to build a molecular-level understanding of how lactylates work. Herein, using the quartz crystal microbalance-dissipation (QCM-D) and electrochemical impedance spectroscopy (EIS) techniques, we investigated the real-time, membrane-disruptive interactions between sodium lauroyl lactylate (SLL)-a promising lactylate with a 12-carbon-long, saturated hydrocarbon chain-and supported lipid bilayer (SLB) and tethered bilayer lipid membrane (tBLM) platforms. For comparison, hydrolytic products of SLL that may be generated in biological environments, i.e., lauric acid (LA) and lactic acid (LacA), were also tested individually and as a mixture, along with a structurally related surfactant (sodium dodecyl sulfate, SDS). While SLL, LA, and SDS all had equivalent chain properties and critical micelle concentration (CMC) values, our findings reveal that SLL exhibits distinct membrane-disruptive properties that lie in between the rapid, complete solubilizing activity of SDS and the more modest disruptive properties of LA. Interestingly, the hydrolytic products of SLL, i.e., the LA + LacA mixture, induced a greater degree of transient, reversible membrane morphological changes but ultimately less permanent membrane disruption than SLL. These molecular-level insights support that careful tuning of antimicrobial lipid headgroup properties can modulate the spectrum of membrane-disruptive interactions, offering a pathway to design surfactants with tailored biodegradation profiles and reinforcing that SLL has attractive biophysical merits as a membrane-disrupting antimicrobial drug candidate.

Native Function of the Bacterial Ion Channel SthK in a Sparsely Tethered Lipid Bilayer Membrane Architecture.

The plasma membrane protects the interiors of cells from their surroundings and also plays a critical role in communication, sensing, and nutrient import. As a result, the cell membrane and its constituents are among the most important drug targets. Studying the cell membrane and the processes it facilitates is therefore crucial, but it is a highly complex environment that is difficult to access experimentally. Various model membrane systems have been developed to provide an environment in which membrane proteins can be studied in isolation. Among them, tethered bilayer lipid membranes (tBLMs) are a promising model system providing a solvent-free membrane environment which can be prepared by self-assembly, is resistant to mechanical disturbances and has a high electrical resistance. tBLMs are therefore uniquely suitable to study ion channels and charge transport processes. However, ion channels are often large, complex, multimeric structures and their function requires a particular lipid environment. In this paper, we show that SthK, a bacterial cyclic nucleotide gated (CNG) ion channel that is strongly dependent on the surrounding lipid composition, functions normally when embedded into a sparsely tethered lipid bilayer. As SthK has been very well characterized in terms of structure and function, it is well-suited to demonstrate the utility of tethered membrane systems. A model membrane system suitable for studying CNG ion channels would be useful, as this type of ion channel performs a wide range of physiological functions in bacteria, plants, and mammals and is therefore of fundamental scientific interest as well as being highly relevant to medicine.

Formation of tethered bilayer lipid membranes on gold surface probed by in situ SEIRAS


 
 
 
 Tethered bilayer lipid membranes (tBLMs) are versatile platforms for the analysis of biochemical and biophysical processes at biological membranes. To control the stability and functional properties of these artificial constructions, molecular-level knowledge on the organization and structure is required. We used surface-enhanced infrared absorption spectroscopy (SEIRAS) to elucidate the in situ formation of tBLMs on a gold substrate. The alkyl chains of long-chain anchoring thiol in a mixed self-assembled monolayer after 60 min of incubation in an adsorption methanol-d4 solution was found to be in a disordered state. Spectroscopic data revealed the complete formation of a bilayer after 60 min of incubation of a mixed anchoring monolayer in a phosphate buffer solution containing vesicles formed from partially deuterated lipid DPPC-d62 and cholesterol-d7. The temporal evolution of absorption bands from the lipid, anchoring mixed monolayer thiol, and water with increasing the bilayer formation time in the phosphate buffer solution containing vesicles revealed a two-stage process. Firstly, the adsorption of lipid molecules with a simultaneous withdrawal of water takes place at the interface. Secondly, the transformation of alkyl chains of the anchoring monolayer due to the insertion and interaction of lipids with the monolayer proceeds.
 
 
 

Tethered Bilayer Lipid Membrane Platform for Screening Triton X-100 Detergent Replacements by Electrochemical Impedance Spectroscopy.

In light of regulatory considerations, there are ongoing efforts to identify Triton X-100 (TX-100) detergent alternatives for use in the biological manufacturing industry to mitigate membrane-enveloped pathogen contamination. Until now, the efficacy of antimicrobial detergent candidates to replace TX-100 has been tested regarding pathogen inhibition in endpoint biological assays or probing lipid membrane disruption in real-time biophysical testing platforms. The latter approach has proven especially useful to test compound potency and mechanism of action, however, existing analytical approaches have been limited to studying indirect effects of lipid membrane disruption such as membrane morphological changes. A direct readout of lipid membrane disruption by TX-100 detergent alternatives would be more practical to obtain biologically relevant information to guide compound discovery and optimization. Herein, we report the use of electrochemical impedance spectroscopy (EIS) to investigate how TX-100 and selected replacement candidates-Simulsol SL 11W (Simulsol) and cetyltrimethyl ammonium bromide (CTAB)-affect the ionic permeability of tethered bilayer lipid membrane (tBLM) platforms. The EIS results revealed that all three detergents exhibited dose-dependent effects mainly above their respective critical micelle concentration (CMC) values while displaying distinct membrane-disruptive behaviors. TX-100 caused irreversible membrane disruption leading to complete solubilization, whereas Simulsol caused reversible membrane disruption and CTAB induced irreversible, partial membrane defect formation. These findings establish that the EIS technique is useful for screening the membrane-disruptive behaviors of TX-100 detergent alternatives with multiplex formatting possibilities, rapid response, and quantitative readouts relevant to antimicrobial functions.

Electrochemical studies of the mitochondrial ROMK2 potassium channel activity reconstituted into the free-standing and tethered bilayer lipid membranes

The renal-outer-medullary‑potassium (ROMK2) channel modulates potassium transport in the kidney. It has been postulated that the ROMK2 is the pore-forming subunit of the mitochondrial ATP-sensitive potassium channel as a mediator of cardioprotection. In this study, cell-free synthesis of the ROMK2 was performed in presence of membrane scaffold protein (MSP1D1) nanodiscs. Activity measurements were achieved after channel reconstitution into the planar lipid bilayer and tethered bilayer lipid membranes. Both methods allowed for monitoring of channel function, verified with channel blocking and activation/re-activation experiments. The primary function of the mitochondrial potassium channels is to regulate the potential of the mitochondrial membrane, which allows them to play an important role in cytoprotection. This work focuses on obtaining the ROMK2 using a cell-free expression system, followed by the incorporation of the channel protein into the lipid bilayer and studying the influence of voltage changes and molecular modulators on channel activity. Channel activity was measured after its reconstitution into two models of lipid bilayers - BLM (Bilayer Lipid Membrane) and tBLM (Tethered Bilayer Lipid Membrane) deposited on a solid gold electrode. These two model membranes and electrochemical measurements made it possible to measure the flux of K+ ions in the presence of channel modulators.

Bilayer lipid membrane formation on surface assemblies with sparsely distributed tethers.

A combined computational and experimental study of small unilamellar vesicle (SUV) fusion on mixed self-assembled monolayers (SAMs) terminated with different deuterated tether moieties (-(CD2)7CD3 or -(CD2)15CD3) is reported. Tethered bilayer lipid membrane (tBLM) formation of synthetic 1-stearoyl-2-oleoyl-sn-glycero-3-phosphocholine was initially probed on SAMs with controlled tether (d-alkyl tail) surface densities and lateral molecular packing using quartz crystal microbalance with dissipation monitoring (QCM-D). Long time-scale coarse-grained molecular dynamics (MD) simulations were then employed to elucidate the mechanisms behind the interaction between the SUVs and the different phases formed by the -(CD2)7CD3 and -(CD2)15CD3 tethers. Furthermore, a series of real time kinetics was recorded under different osmotic conditions using QCM-D to determine the accumulated lipid mass and for probing the fusion process. It is shown that the key factors driving the SUV fusion and tBLM formation on this type of surfaces involve tether insertion into the SUVs along with vesicle deformation. It is also evident that surface densities of the tethers as small as a few mol% are sufficient to obtain stable tBLMs with a high reproducibility. The described "sparsely tethered" tBLM system can be advantageous in studying different biophysical phenomena, such as membrane protein insertion, effects of receptor clustering, and raft formation.

The role of ion-lipid interactions and lipid packing in transient defects caused by phenolic compounds

The transient disruption of membranes for the passive permeation of ions or small molecules is a complex process relevant to understanding physiological processes and biotechnology applications. Phenolic compounds are widely studied for their antioxidant and antimicrobial properties, and some of these activities are based on the interactions of the phenolic compound with membranes. Ions are ubiquitous in cells and are known to alter the structure of phospholipid bilayers. Yet, ion-lipid interactions are usually ignored when studying the membrane-altering properties of phenolic compounds. This study aims to assess the role of Ca2+ ions on the membrane-disrupting activity of two phenolic acids and to highlight the role of local changes in lipid packing in forming transient defects or pores. Results from tethered bilayer lipid membrane electrical impedance spectroscopy experiments showed that Ca2+ significantly reduces membrane disruption by caffeic acid methyl ester and caffeic acid. As phenolic acids are known metal chelators, we used UV-vis and fluorescence spectroscopy to exclude the possibility that Ca2+ interferes with membrane disruption by binding to the phenolic compound and subsequently preventing membrane binding. Molecular dynamics simulations showed that Ca2+ but not caffeic acid methyl ester or caffeic acid increases lipid packing in POPC bilayers. The combined data confirm that Ca2+ reduces the membrane-disrupting activity of the phenolic compounds, and that Ca2+-induced changes to lipid packing govern this effect. We discuss our data in the context of ion-induced pores and transient defects and how lipid packing affects membrane disruption by small molecules.

A procedure for estimating the absolute potential difference across metal|water interfaces: A reassessment

The estimate of the absolute potential difference across metal|aqueous solution (M|W) interfaces is of paramount importance to compare the behavior of ion channels incorporated in metal-supported biomimetic membranes with that in biomembranes and, most importantly, to obtain further behavioral information by the use of surface sensitive techniques. In 2011 Guidelli and Becucci described a procedure based on the use of a thiolipid called DPTL, consisting of a tetraethyleneoxy (TEO) hydrophilic chain terminated at one end with a lipoic acid residue, for anchoring to the mercury surface, and covalently linked at the other end to two phytanyl chains mimicking the hydrocarbon tails of a phospholipid. DPTL has been widely employed to fabricate metal supported tethered bilayer lipid membranes (tBLMs) by anchoring it to the metal surface of Hg, Au, and Ag. The above procedure relies on an independent estimate of the surface dipole potential χTEO of the TEO chain tethered to Hg and on the reasonable assumption that it remains unaltered when tethered to other metals. The present note corrects an erroneous estimate of the absolute potential difference across a polycrystalline Au|W interface in the 2011 paper, provides a clearer explanation of the procedure using the concept of electrochemical potential of electrons, estimates the absolute potential difference across the Au(111)|W interface, and compares the results of the proposed procedure with Trasatti’s ‘interfacial term’.

Mechanistic Evaluation of Antimicrobial Lipid Interactions with Tethered Lipid Bilayers by Electrochemical Impedance Spectroscopy

There is extensive interest in developing real-time biosensing strategies to characterize the membrane-disruptive properties of antimicrobial lipids and surfactants. Currently used biosensing strategies mainly focus on tracking membrane morphological changes such as budding and tubule formation, while there is an outstanding need to develop a label-free biosensing strategy to directly evaluate the molecular-level mechanistic details by which antimicrobial lipids and surfactants disrupt lipid membranes. Herein, using electrochemical impedance spectroscopy (EIS), we conducted label-free biosensing measurements to track the real-time interactions between three representative compounds—glycerol monolaurate (GML), lauric acid (LA), and sodium dodecyl sulfate (SDS)—and a tethered bilayer lipid membrane (tBLM) platform. The EIS measurements verified that all three compounds are mainly active above their respective critical micelle concentration (CMC) values, while also revealing that GML induces irreversible membrane damage whereas the membrane-disruptive effects of LA are largely reversible. In addition, SDS micelles caused membrane solubilization, while SDS monomers still caused membrane defect formation, shedding light on how antimicrobial lipids and surfactants can be active in, not only micellar form, but also as monomers in some cases. These findings expand our mechanistic knowledge of how antimicrobial lipids and surfactants disrupt lipid membranes and demonstrate the analytical merits of utilizing the EIS sensing approach to comparatively evaluate membrane-disruptive antimicrobial compounds.

Deciphering the Assembly of Enveloped Viruses Using Model Lipid Membranes.

The cell plasma membrane is mainly composed of phospholipids, cholesterol and embedded proteins, presenting a complex interface with the environment. It maintains a barrier to control matter fluxes between the cell cytosol and its outer environment. Enveloped viruses are also surrounded by a lipidic membrane derived from the host-cell membrane and acquired while exiting the host cell during the assembly and budding steps of their viral cycle. Thus, model membranes composed of selected lipid mixtures mimicking plasma membrane properties are the tools of choice and were used to decipher the first step in the assembly of enveloped viruses. Amongst these viruses, we choose to report the three most frequently studied viruses responsible for lethal human diseases, i.e., Human Immunodeficiency Type 1 (HIV-1), Influenza A Virus (IAV) and Ebola Virus (EBOV), which assemble at the host-cell plasma membrane. Here, we review how model membranes such as Langmuir monolayers, bicelles, large and small unilamellar vesicles (LUVs and SUVs), supported lipid bilayers (SLBs), tethered-bilayer lipid membranes (tBLM) and giant unilamellar vesicles (GUVs) contribute to the understanding of viral assembly mechanisms and dynamics using biophysical approaches.

Inkjet-Printed Phospholipid Bilayers on Titanium Oxide Surfaces: Towards Functional Membrane Biointerfaces.

Functional biointerfaces hold broad significance for designing cell-responsive medical implants and sensor devices. Solid-supported phospholipid bilayers are a promising class of biological materials to build bioinspired thin-film coatings, as they can facilitate interactions with cell membranes. However, it remains challenging to fabricate lipid bilayers on medically relevant materials such as titanium oxide surfaces. There are also limitations in existing bilayer printing capabilities since most approaches are restricted to either deposition alone or to fixed microarray patterning. By combining advances in lipid surface chemistry and on-demand inkjet printing, we demonstrate the direct deposition and patterning of covalently tethered lipid bilayer membranes on titanium oxide surfaces, in ambient conditions and without any surface pretreatment process. The deposition conditions were evaluated by quartz crystal microbalance-dissipation (QCM-D) measurements, with corresponding resonance frequency (Δf) and energy dissipation (ΔD) shifts of around −25 Hz and <1 × 10−6, respectively, that indicated successful bilayer printing. The resulting printed phospholipid bilayers are stable in air and do not collapse following dehydration; through rehydration, the bilayers regain their functional properties, such as lateral mobility (>1 µm2/s diffusion coefficient), according to fluorescence recovery after photobleaching (FRAP) measurements. By taking advantage of the lipid bilayer patterned architectures and the unique features of titanium oxide’s photoactivity, we further show how patterned cell culture arrays can be fabricated. Looking forward, this work presents new capabilities to achieve stable lipid bilayer patterns that can potentially be translated into implantable biomedical devices.

A rationally designed synthetic antimicrobial peptide against Pseudomonas-associated corneal keratitis: Structure-function correlation

Contact lens wearers are at an increased risk of developing Pseudomonas-associated corneal keratitis, which can lead to a host of serious ocular complications. Despite the use of topical antibiotics, ocular infections remain a major clinical problem, and a strategy to avoid Pseudomonas-associated microbial keratitis is urgently required. The hybrid peptide VR18 (VARGWGRKCPLFGKNKSR) was designed to have enhanced antimicrobial properties in the fight against Pseudomonas-induced microbial keratitis, including contact lens-related keratitis. In this paper, VR18's modes of action against Pseudomonas membranes were shown by live cell Raman spectroscopy, live cell NMR, live-cell fluorescence microscopy and measures taken using sparsely tethered bilayer lipid membrane bacterial models to be via a bacterial-specific membrane disruption mechanism. The high affinity and selectivity of the peptide were then demonstrated using in vivo, in vitro and ex vivo models of Pseudomonas infection. The extensive data presented in this work suggests that topical employment of the VR18 peptide would be a potent therapeutic agent for the prevention or remedy of Pseudomonas-associated microbial keratitis.

Electrochemical impedance spectroscopy of heterogenous tethered lipid bilayers

Tethered lipid bilayer membranes (tBLM’s) are biomimetic model membranes, that enable protein reconstitution. Submembrane reservoir that separates lipid bilayer from solid support prevents reconstituted proteins from jamming against solid surface. However, this makes tBLM’s intrinsically asymmetric, bathed in ∼1.5-2 nm electrolyte reservoir from one side and practically infinite electrolyte layer from the other side. This asymmetry hinders possibility to measure conductance of ion channels. On the other hand, this asymmetry allows to estimate lateral organization of ionic channels without utilizing microscopic techniques.

Effect of dipole potential on the orientation of Voltage-gated Alamethicin peptides regulated by chaotropic anions

• A new tBLMs model was proposed to accommodate the voltage-gated Alm peptides. • Chaotropic anions induce dipole potential decrease by disrupting the water structure. • A lower dipole potential facilitates the peptide to adopt a more upright orientation. Understanding the gating mechanism of ion channel proteins is the basis for regulating cell activity and designing new drug molecules, but it still remains a great challenge. Herein, a new tethered bilayer lipid membranes (tBLMs) model was proposed to accommodate the voltage-gated ion channel model-Alamethicin (Alm) peptides. Using surface-enhanced infrared absorption (SEIRA) spectroelectrochemistry combined with fluorescence spectroscopy, it was found that the orientation of the peptides inserted into the membranes was affected by membrane dipole potential regulated by chaotropic anions. A lower dipole potential could reduce the energy barrier of the insertion of peptides into the membranes, which facilitates the peptides to adopt a more upright orientation in the membranes. This research is of great significance for understanding the mechanism of ion channel-related diseases.