Terahertz Near-field Imaging Research Articles

Terahertz Near-Field Imaging of Buried Structures

Terahertz Near-Field Imaging of Buried Structures

Non-contact imaging of terahertz surface currents with aperture-type near-field microscopy.

Terahertz (THz) near-field imaging and spectroscopy provide valuable insights into the fundamental physical processes occurring in THz resonators and metasurfaces on the subwavelength scale. However, so far, the mapping of THz surface currents has remained outside the scope of THz near-field techniques. In this study, we demonstrate that aperture-type scanning near-field microscopy enables non-contact imaging of THz surface currents in subwavelength resonators. Through extensive near-field mapping of an asymmetric D-split-ring THz resonator and full electromagnetic simulations of the resonator and the probe, we demonstrate the correlation between the measured near-field images and the THz surface currents. The observed current dynamics in the interval of several picoseconds reveal the interplay between several excited modes, including dark modes, whereas broadband THz near-field spectroscopy analysis enables the characterization of electromagnetic resonances defined by the resonator geometry.

THz near-field intensity distribution imaging in the 0.3 THz band using a highly sensitive polarization CMOS image sensor using a 0.35 μm CMOS process

In this paper, we propose a low-disturbance and fast terahertz (THz) near-field intensity distribution imaging method. The THz detector is fabricated using an oriented multiwalled carbon nanotube (CNT) thin film and a LiNbO3(LN) crystal to the thin film is attached. The CNT absorbs and converts THz waves into heat, and the birefringence change of the LN crystal owing to the heat is used. The birefringence change was measured with high sensitivity using a dual-polarizer configuration of a uniform polarizer and a polarization CMOS image sensor. The fabricated THz detector is a low-disturbance method because it does not use metal, and it can measure the THz distribution in the plane all at once, which is faster than the antenna scanning method. Using the proposed method, we have successfully imaged the THz near-field intensity distribution emitted from an impact avalanche and transit time diode oscillating at 0.278 THz.

Biomedical application of terahertz imaging technology: a narrative review.

Terahertz (THz) imaging has wide applications in biomedical research due to its properties, such as non-ionizing, non-invasive and distinctive spectral fingerprints. Over the past 6 years, the application of THz imaging in tumor tissue has made encouraging progress. However, due to the strong absorption of THz by water, the large size, high cost, and low sensitivity of THz devices, it is still difficult to be widely used in clinical practice. This paper provides ideas for researchers and promotes the development of THz imaging in clinical research. The literature search was conducted in the Web of Science and PubMed databases using the keywords "Terahertz imaging", "Breast", "Brain", "Skin" and "Cancer". A total of 94 English language articles from 1 January, 2017 to 30 December, 2022 were reviewed. In this review, we briefly introduced the recent advances in THz near-field imaging, single-pixel imaging and real-time imaging, the applications of THz imaging for detecting breast, brain and skin tissues in the last 6 years were reviewed, and the advantages and existing challenges were identified. It is necessary to combine machine learning and metamaterials to develop real-time THz devices with small size, low cost and high sensitivity that can be widely used in clinical practice. More powerful THz detectors can be developed by combining graphene, designing structures and other methods to improve the sensitivity of the devices and obtain more accurate information. Establishing a THz database is one of the important methods to improve the repeatability and accuracy of imaging results. THz technology is an effective method for tumor imaging. We believe that with the joint efforts of researchers and clinicians, accurate, real-time, and safe THz imaging will be widely applied in clinical practice in the future.

Fiber-tip spintronic terahertz emitters.

Spintronic terahertz emitters promise terahertz sources with an unmatched broad frequency bandwidth that are easy to fabricate and operate, and therefore easy to scale at low cost. However, current experiments and proofs of concept rely on free-space ultrafast pump lasers and rather complex benchtop setups. This contrasts with the requirements of widespread industrial applications, where robust, compact, and safe designs are needed. To meet these requirements, we present a novel fiber-tip spintronic terahertz emitter solution that allows spintronic terahertz systems to be fully fiber-coupled. Using single-mode fiber waveguiding, the newly developed solution naturally leads to a simple and straightforward terahertz near-field imaging system with a 90%-10% knife-edge-response spatial resolution of 30 µm.

Label-free detection and identification of single bacteria via terahertz near-field imaging.

In recent years, terahertz (THz) imaging has attracted much attention because of its ability to obtain physical and chemical information in a label-free, noninvasive and nonionizing manner. However, the low spatial resolution of traditional THz imaging systems and the weak dielectric response of biological samples hinder the application of this technology in the biomedical field. In this paper, we report a new THz near-field imaging method for a single bacteria, through the coupling effect of nanoscale radius of probe and platinum gold substrate, which greatly enhances THz near-field signal of biological samples. A THz super-resolution image of bacteria has been successfully obtained by strictly controlling the relevant test parameters such as tip parameters and driving amplitude. By analyzing and processing the THz spectral image, the morphology and inner structure of bacteria have been observed. The method has been used to detect and identify Escherichia coli represented by Gram-negative bacteria and Staphylococcus aureus represented by Gram-positive bacteria. This application provides a new label-free, noninvasive and nonionizing testing protocol for the detection of single bacteria.

Terahertz near-field imaging of graphene disks

Due to the weak power of Terahertz sources, metal tips are often used to enhance the signal intensity of the Terahertz scattering scanning near-field optical microscope (THz s-SNOM). However, while enhancing the near-field, metal tips also affect the field distribution on the sample surface. In this paper, a home-built 97.8GHz sub-Terahertz near-field imaging system was used to image graphene disks with dozens of microns in diameter. It was found that the field distribution was significantly different from that without the tip, and was related to the incident direction of the terahertz wave.

Curved Synthetic Aperture Radar for Near-Field Terahertz Imaging

High resolution imaging technique will play an essential role in the future smart imaging applications to provide potential solutions for accurate detection, monitoring and classification of the target. The potential of synthetic aperture radar (SAR) systems to acquire high resolution images has opened new frontiers and led to its exploration in new applications. The conventional microwave radar imaging suffers limited range resolution in the sub-millimeter wave range and optical imaging methods are constrained by the diffraction limit. In the terahertz (THz) regime of the spectrum, the SAR systems could be operated in all the weather, all the time and are capable of penetrating through clouds, smoke, dust etc. to achieve high resolution images beyond the diffraction limit. The curved SAR presents a SAR system created by circularly encircling the target scene. The Circular SAR and Spiral SAR which are based on a circular and cylindrical spiral scanning trajectory, respectively are the scanning methods used for curved SAR. In this paper, we have explored a new toolbox that enables the rapid development of near-field THz-SAR imaging systems and generation of large near-field THz imaging scenarios with the goal to support and facilitate data driven research such as deep learning in the THz community through synthetically generated SAR images as well as its potential for THz based high resolution and 2D/3D near-field imaging application. Initially, the potential advantages of THz-SAR over Microwave SAR and optical imaging methods are presented. Further, a frequency modulated continuous wave (FMCW) radar testbed is simulated in multi-input multi-output (MIMO) configuration for the target frequency band. Moreover, the circular and cylindrical SAR scanning methods are explored for near-field imaging of point targets to obtain 2D and 3D THz-SAR images, respectively. Also, the radar images are reconstructed using the Back Propagation and Polar Formatting Algorithms, focusing on short range applications like indoor environments. Finally, the SAR performance evaluation metrics are reported and a roadmap for future work is presented.

Review on Super-Resolution Near-Field Terahertz Imaging Methods

Review on Super-Resolution Near-Field Terahertz Imaging Methods

Focus on lasers, imaging, microscopy, and photonics

Focus on lasers, imaging, microscopy, and photonics

Fabrication and characterization of a composite TiO2-polypropylene high-refractive-index solid immersion lens for super-resolution THz imaging

Terahertz (THz) near-field imaging is attracting a lot of attention for its potential applications in medical diagnosis and material characterization. However, the spatial resolution of the recorded THz image was mainly limited by the diffraction limit of the commonly used lens- and mirror-based THz optical systems. Alternatively, a solid immersion lens (SIL) can be a promising approach for achieving super-resolution imaging as it reduces the spot size of the focused THz beam by a factor of 1/n, where n is the refractive index (RI) of the lens material. In this work, we present the design and fabrication of hemispherical THz SIL using powder mixes of titanium dioxide (TiO2) and polypropylene (PP) whose RIs are ≈10 and ≈1.51, respectively, at 1.0 THz. In particular, we present two different lens fabrication strategies that are simple and cost-effective solutions. The first strategy uses pressing the TiO2 powder with a PP powder at the Vicat temperature of PP while controlling the concentration of TiO2 and the resultant lens porosity. The second design consists in pressing the TiO2 powder in a hollow hemisphere that is 3D printed using PP. The fabricated lenses are then characterized physically and optically, and their RIs are compared to the theoretical estimates using the Bruggeman model of the effective media. From the experimental measurements of the proposed SIL, a resolution limit as low as 0.2λ was achieved at 0.09 THz (λ ≈ 3.3 mm), which is comparable to the best resolutions reported in the literature.

Dual-band giant spin-selective full-dimensional manipulation of graphene-based chiral meta-mirrors for terahertz waves.

The ability to simultaneous achieve circular dichroism (CD) and wavefront manipulation is extremely important for many practical applications, especially for detecting and imaging. However, many of the previously observed weakness chiral features are limited to nanostructures with complex three-dimensional building configurations, single narrow-band response, and no active tunability, which are getting farther and away from the goal of integration and miniaturization. Here, a platform of bi-layer all-graphene meta-mirrors with spin-selective full-dimensional manipulation is proposed to simultaneously achieve giant dual-band CD response and wavefront shaping, based on the principle of the hybridization coupling. By simply controlling the structural variables of the meta-mirror and the characteristic parameters of graphene, that is, the combination of passive and active regulation, the proposed design can selectively manipulate the polarization, amplitude, phase, and working frequency of the incident circularly polarized wave near-independently. As a proof of concept, we used the meta-mirror to design two metasurface arrays with spin-selective properties for dynamic terahertz (THz) wavefront shaping and near-field digital imaging, both of which show a high-performance dynamic tunability. This method could provide additional options for the next-generation intelligent THz communication systems.

Dual-band terahertz all-silicon metasurface with giant chirality for frequency-undifferentiated near-field imaging.

Chiral metasurfaces are widely used in imaging and biosensing due to their powerful light field control capabilities. Most of the work is devoted to achieving the goals of chirality enhancement and tunability, but lacks consideration of design complexity, loss, cost, and multi-band operation. In order to alleviate this situation, we propose a pair of dual-frequency giant chiral structures based on all-silicon, which can achieve excellent and opposite spin-selective transmission around 1.09 THz and 1.65 THz. The giant chirality derives from the in-plane electric and magnetic dipole moments excited in different degrees. Theoretically, the maximum circular dichroism at the two frequencies are both as high as 0.34, and the coverage bandwidths of the two giant chirality are 85.5 GHz and 41.4 GHz, respectively. The experimental results are in good agreement with the simulation results. Based on the dual-band giant chiral patterns, the terahertz near-field imaging of different Chinese character images is demonstrated at two frequencies. The frequency-undifferentiated characteristics, good intensity contrast and three-dimensional imaging information are shown by the results. This work provides new ideas for the design of terahertz devices with simple structure and multi-functions, which are expected to be applied in the field of terahertz imaging or multi-channel communication.

Nondestructive inspection of packaged microcircuits by aperture-type terahertz near-field imaging

A scanning aperture-type terahertz near-field imaging system is developed to perform precise nondestructive testing on packaged aluminum etched antenna arrays, and surface imaging of a flexible gold electrode array, to obtain subsurface imaging and surface imaging. The resolution of subsurface imaging is 110 and 500 μm when the packaging (polyethylene terephthalate) thickness is 50 and 200 μm respectively, and the surface imaging resolution is 6 μm at 0.11 THz. An adaptive threshold segmentation algorithm of Hilbert scan combined with wavelet transform were employed to successfully suppress the noise of the imaging results due to the change of near-field distance. We also proposed a derivative filtering extremum threshold segmentation algorithm to effectively suppress severely uneven threshold distribution of the packaged aluminum etched antenna arrays.

Unveiling the Symmetry Protection of Bound States in the Continuum with Terahertz Near-Field Imaging.

Bound states in the continuum (BICs) represent a new paradigm in photonics due to the full suppression of radiation losses. However, this suppression has also hampered the direct observation of them. By using a double terahertz (THz) near-field technique that allows the local excitation and detection of the THz amplitude, we are able to map for the first time the electromagnetic field amplitude and phase of BICs over extended areas, unveiling the field-symmetry protection that suppresses the far-field radiation. This investigation, done for metasurfaces of dimer scatterers, reveals the in-plane extension and formation of BICs with antisymmetric phases, in agreement with coupled-dipole calculations. By displacing the scatterers, we show experimentally that a mirror symmetry is not a necessary condition for a BIC formation. Only π-rotation symmetry is required, making BICs exceptionally robust to structural changes. This work makes the local field of BICs experimentally accessible, which is crucial for the engineering of cavities with infinite lifetimes.

Aperture-type terahertz near-field imaging with a cylindrical frustum-shaped plastic probe.

We designed an aluminum-coated plastic probe made from the combination of cylinder and a frustum of a cone for terahertz near-field imaging. The bunching width of the probe is 12 µm and the electric field intensity enhancement factor just outside the probe tip reaches up to 25. An imaging resolution obtained through near-field imaging experiments on a variety of targets, including narrow metals and narrow media, is 6 µm (λ/450) at 0.11 THz. By adopting an adaptive threshold segmentation image processing algorithm that combines Hilbert scanning and wavelet transform, the influence of a large area of metal near the imaging area on the imaging result is successfully suppressed. Imaging of a scratch on the plastic substrate makes the new probe feasible for quality identification of nonmetallic cultural relics.

Label-Free Observation of Micrometric Inhomogeneity of Human Breast Cancer Cell Density Using Terahertz Near-Field Microscopy

Terahertz-light imaging is attracting great attention as a new approach in non-invasive/non-staining biopsy of cancerous tissues. Positively, terahertz light has been shown to be sensitive to the cell density, the hydration content, and the chemical composition of biological samples. However, the spatial resolution of terahertz imaging is typically limited to several millimeters, making it difficult to apply the technology to image biological tissues which have sub-terahertz-wavelength-scale inhomogeneity. For overcoming the resolution, we have recently developed a terahertz near-field microscope with a spatial resolution of 10 µm, named scanning point terahertz source (SPoTS) microscope. In contrast to conventional far-field terahertz techniques, this microscope features the near-field interactions between samples and point terahertz sources on a sub-terahertz-wavelength scale. Herein, to evaluate the usefulness of terahertz imaging in cancer tissue biopsy in greater detail, we performed terahertz near-field imaging of a paraffin-embedded human-breast-cancer section having sub-terahertz-wavelength-scale inhomogeneity of the cancer cell density using the SPoTS microscope. The observed terahertz images successfully visualized local (~250 µm) inhomogeneities of the cell density in breast invasive ductal carcinoma. These results may bypass the terahertz limitation in terms of spatial resolution and may further motivate the application of terahertz light to cancer tissue biopsy.

Phase-Controlled Planar Metalenses for High-Resolution Terahertz Focusing

We experimentally demonstrate that high-resolution terahertz focusing can be realized in planar metalenses, which consist of arrays of different V-shaped antenna units on a silicon substrate. Numerical results show that a larger numerical aperture of metalenses can provide smaller full width at half maximum of field distribution, leading to higher spatial resolution. The measurement of fabricated metalenses samples was performed by a terahertz near-field imaging system, and experimental results agree well with the numerical prediction. Especially for 1.1 THz incident light, when the numerical aperture increases from 0.79 to 0.95, the full width at half maximum correspondingly decreases from 343 μm to 206 μm, offering an improvement of spatial resolution.

Terahertz measurement based on Rydberg atomic antenna

Rydberg atoms have large electric dipole moments in the microwave and terahertz frequency band. The detection of electromagnetic field intensity in this frequency band can be achieved by using quantum interference effects. Theoretically, this detection method can have a sensitivity much higher than the traditional detection methods. Therefore, electromagnetic field detection and precision measurement technology based on Rydberg atomic quantum effects has great application prospects in terahertz field strength and power measurement, terahertz communication and imaging. In this paper, we review the basic theory and experimental methods to realize the self-calibration and traceability measurement of electromagnetic field based on Rydberg atomic quantum effects. The principle and technical scheme of high-sensitivity terahertz field strength measurement, terahertz near-field high-speed imaging and terahertz digital communication based on Rydberg atom are introduced in detail. Finally, the processing terahertz detection work based on Rydberg atom by our research team is also mentioned briefly.

Terahertz Spectroscopy of Gas Absorption Using the Superconducting Flux-Flow Oscillator as an Active Source and the Superconducting Integrated Receiver.

We report on the first implementation of a terahertz (THz) source based on a Josephson flux-flow oscillator (FFO) that radiates to open space. The excellent performance of this source and its maturity for practical applications has been demonstrated by the spectroscopy of gas absorption. To study the radiated power, we used a bolometric detection method and additionally calibrated the power by means of pumping the superconductor–insulator–superconductor (SIS) junction, integrated on a single chip with the FFO. For calibration, we developed a program using the SIS-detected power calculations in accordance with the Tien and Gordon model. The power emitted to open space is estimated to be from fractions of µW to several µW in the wide region from 0.25 THz up to 0.75 THz for different designs, with a maximum power of 3.3 µW at 0.34 THz. Next, we used a gas cell and a heterodyne superconducting integrated receiver to trace the absorption lines of water and ammonia with a spectral resolution better than 100 kHz. Our experiment for gas absorption is the first demonstration of the applicability of the FFO as an external active source for different tasks, such as THz spectroscopy, near-field THz imaging and microscopy.