Tensile Elastic Modulus Research Articles

Colloidal and thermal properties of poly(hydroxyethyl caprolactone acrylate‐co‐methyl methacrylate)‐g‐pullulan latex obtained by seeded semi‐batch emulsion polymerization

AbstractIn this study, the influence that the monomer composition of hydroxyethyl caprolactone acrylate/methyl methacrylate (HECLA/MMA) has on the properties of the latex films, including contact angle, thermogravimetric analysis, and mechanical properties was evaluated. The polymerization process to obtain small particle sizes, good colloidal stability, and polymer films was optimized through the use of pullulan (Pull) and different ratios of HECLA and MMA. The results revealed a substantial impact of the monomer composition and polymerization processes on the particle size and latex film properties. The use of seed latex obtained in situ reduces particle size and particle size distribution. Additionally, it was observed that the contact angle of the polymer films increased as the concentration of HECLA increased. Furthermore, the water absorption of the polymer films exhibited a decreasing trend after reaching an 80/20 monomer composition of HECLA/MMA. An increase in HECLA contents in the recipe showed a reduction in tensile strength, elastic modulus, hardness, and elongation at break. Conversely, higher HECLA contents contributed to improving the thermal properties of the polymer films. Finally, the optimal ratio of HECLA/MMA to improve the thermal degradation and tensile mechanical properties of the polymer film was 50/50 wt%. The results found in this work allow additional data for producing poly(HECLA‐co‐MMA)‐g‐Pull latexes by manipulating the ratios of HECLA and MMA, which can create new potential applications in various industrial settings for a wide range of polysaccharides.Highlights Poly(HECLA‐co‐MMA)‐g‐Pull with different ratios of HECLA/MMA were successfully obtained. The use of Pull after molar mass reduction had a significant effect on colloidal stability. A reduction in tensile strength and elongation at break was obtained by increasing the amount of HECLA. Thermal stability of the latex films showed a direct relationship with the content of HECLA. Poly(HECLA‐co‐MMA)‐g‐Pull latexes can be used in agricultural applications.

Optimization of mechanical properties and dimensional stability of densified wood using response surface methodology

Wood has gained popularity as a building and decorative material due to its environmentally friendly and sustainable characteristics. Yet, its long maturation time poses a limitation on meeting the growing demand for wood products. This challenge has led to the plantation of fast-growing wood as an alternative solution. Unfortunately, the poor mechanical properties of fast-growing wood hinder its application. In this study, we developed novel densification-modified wood by combining alkali chemical pretreatment, cyclic impregnation, and mechanical hot-pressing techniques. Additionally, the response surface method was employed to rapidly determine the optimal preparation parameters, reducing the cost of preparation under various conditions. The optimized parameters resulted in densification-modified wood with a flexural strength and modulus of elasticity of 337.04 MPa and 27.43 GPa, respectively. Furthermore, the densified wood achieved excellent dimensional stability by reducing the water-absorbing thickness swelling to 1.15 % for 72-h water soaking. The findings indicated that the densification-modified wood possessed high tensile strength and elastic modulus, along with excellent dimensional stability. The proposed densified wood modification technology in this study offers new perspectives and design guidance for the application of outdoor engineering structures, energy-efficient buildings, and decorative materials.

Biochar for sustainable additive manufacturing: Thermal, mechanical, electrical, and rheological responses of polypropylene-biochar composites

The utilization of eco-friendly reinforcing materials and the fabrication of sustainable composites with enhanced mechanical and electrical properties are a subject of great scientific interest. Such research is aiming to be applied in a variety of industrial applications. In this study, polypropylene (PP) was used as a matrix material and combined with biochar (BC) as a filler at different loadings (2.0, 4.0, 6.0, 8.0, and 10.0 wt %) to produce reinforced composites. Biochar was produced from olive tree prunings. Additively manufactured specimens underwent a variety of tests (fourteen in total) regarding their thermal, structural, mechanical, morphological, and electrical properties. The mechanical properties of the PP were improved by the addition of 4.0 wt % biochar, as the tensile strength and modulus of elasticity, presented a 28.4 % and 24.3 % increase compared to that of pure PP. Overall, the 6 wt % was the optimum loading considering all the tests conducted. The thermal stability of the PP/BC composites was significantly improved compared to that of pure PP. At a filler loading of 8.0 wt %, the dc-conductivity of PP/biochar composite increased by more than 9 orders of magnitude, suggesting the existence of a percolation threshold, above which the polymer composite switches from insulating behavior to a conductive state. Overall, biochar addition had a positive impact on all measured quantities and proved to be an eco-friendly material suitable for use in various applications of additive manufacturing (AM).

Characterization and Implementation of Cocoa Pod Husk as a Reinforcing Agent to Obtain Thermoplastic Starches and Bio-Based Composite Materials.

When the cocoa pod husk (CPH) is used and processed, two types of flour were obtained and can be differentiated by particle size, fine flour (FFCH), and coarse flour (CFCH) and can be used as a possible reinforcement for the development of bio-based composite materials. Each flour was obtained from chopping, drying by forced convection, milling by blades, and sieving using the 100 mesh/bottom according to the Tyler series. Their physicochemical, thermal, and structural characterization made it possible to identify the lower presence of lignin and higher proportions of cellulose and pectin in FFCH. Based on the properties identified in FFCH, it was included in the processing of thermoplastic starch (TPS) from the plantain pulp (Musa paradisiaca) and its respective bio-based composite material using plantain peel short fiber (PPSF) as a reinforcing agent using the following sequence of processing techniques: extrusion, internal mixing, and compression molding. The influence of FFCH contributed to the increase in ultimate tensile strength (7.59 MPa) and higher matrix-reinforcement interaction when obtaining the freshly processed composite material (day 0) when compared to the bio-based composite material with higher FCP content (30%) in the absence of FFCH. As for the disadvantages of FFCH, reduced thermal stability (323.57 to 300.47 °C) and losses in ultimate tensile strength (0.73 MPa) and modulus of elasticity (142.53 to 26.17 MPa) during storage progress were identified. In the case of TPS, the strengthening action of FFCH was not evident. Finally, the use of CFCH was not considered for the elaboration of the bio-based composite material because it reached a higher lignin content than FFCH, which was expected to decrease its affinity with the TPS matrix, resulting in lower mechanical properties in the material.

Janus organohydrogels to realize strain sensitivity, tough adhesion, and environmental stability

Conductive hydrogels (CHs) have been successfully applied in wearable sensors, health monitoring, and smart electronic skins. However, conventional CHs are unstable for long-term use, mainly because of the dehydration in dry environments, freezing at low temperatures, and lack of self-adhesion properties. Herein, a Janus organohydrogel was reported to address this issue, which had a porous matrix and a dense layer to maximize their functionalities. The bottom was made from polyvinyl alcohol (PVA), water, and glycerol, to fabricate an environmental stable and robust matrix; while the top was consisted of grape seed protein (GSP), tannic acid (TA), carbon nanotubes (CNTs), and water to form the conductive yet adhesive layer. Due to the strong hydrogen bonding between glycerol and water, the evaporation and freezing issues were restrained, resulting in a resilient, conductive, adhesive, and stable organohydrogel. For example, the weight loss was 14 % after storing at ambient conditions for 7 days, and the tensile strength and elastic modulus remained 790 and 360 kPa after cooling at −20 °C. Additionally, the catechol groups from TA and amino acids from GSP endowed robust adhesion to wood, cardboard, iron, rubber, plastics, glass, and pigskin (>7 days). Moreover, the introduction of CNTs within Janus structures promoted electron transportation, resulting in high sensitivity (GF = 1.4) at low content (0.02 wt%). Bearing several merits, the present strategy is expected to greatly enrich the functions and expand the applications of conductive hydrogels.

The effect of MgO nanoparticle on PVA/PEG-based membranes for potential application in wound healing

The interest in wound dressings increased ten years ago. Wound care practitioners can now use interactive/bioactive dressings and tissue-engineered skin substitutes. Several bandages can heal burns, but none can treat all chronic wounds. This study formulates a composite material from 70% polyvinyl alcohol (PVA) and 30% polyethylene glycol (PEG) with 0.2, 0.4, and 0.6 wt% magnesium oxide nanoparticles. This study aims to create a biodegradable wound dressing. A Fourier Transform Infrared (FTIR) study shows that PVA, PEG, and MgO create hydrogen bonding interactions. Hydrophilic characteristics are shown by the polymeric blend’s 56.289° contact angle. MgO also lowers the contact angle, making the film more hydrophilic. Hydrophilicity improves film biocompatibility, live cell adhesion, wound healing, and wound dressing degradability. Differential Scanning Calorimeter (DSC) findings suggest the PVA/PEG combination melted at 53.16 °C. However, adding different weight fractions of MgO nanoparticles increased the nanocomposite’s melting temperature (Tm). These nanoparticles improve the film’s thermal stability, increasing Tm. In addition, MgO nanoparticles in the polymer blend increased tensile strength and elastic modulus. This is due to the blend’s strong adherence to the reinforcing phase and MgO nanoparticles’ ceramic material which has a great mechanical strength. The combination of 70% PVA + 30% PEG exhibited good antibacterial spatially at 0.2% MgO, according to antibacterial test results.

Incorporation of ground mustard seeds in an active packaging film: structural properties and controlled release of allyl isothiocyanate

SummaryGround mustard seeds can be incorporated into a packaging film material to have a controlled release of allyl isothiocyanates (AITC). However, the properties of film material loaded with ground mustard seeds need to be evaluated, since they might influence the release of AITC from the film materials. This study aimed to assess properties, including surface morphology, spectral analysis, crystallinity, the moisture‐related, thermal and mechanical properties, of the film materials incorporated with the ground seeds and the release of antimicrobial compounds. Furthermore, the effects of relative humidity on AITC release in the headspace were investigated. The results showed that incorporating a larger quantity of ground mustard seeds resulted in the quicker release of AITC due to direct exposure to moisture, as indicated by higher concentrations observed in the headspace. Meanwhile, a smaller quantity of ground seeds added to the film maintained the thermal properties of the materials until 100 °C, resulting in significantly better moisture‐related properties and higher mechanical strength in terms of tensile strength, elastic modulus, and strain at break. However, the smallest ratio (1:5) showed no release of AITC into the packaging headspace at 75% and 100% RH. Furthermore, the relative humidity led to the release of more AITC in the headspace, which is potentially applied for high‐moisture food products. Based on the influence of relative humidity on AITC concentrations, the mechanism of AITC release from the film materials is proposed, describing the AITC diffusion from ground mustard seeds, film, and headspace.

Effects of high-intensity ultraviolet irradiation on the structure and mechanical properties of Sisal fibers

Abstract To explore the impact of high-intensity ultraviolet light on the structure and mechanical properties of sisal fibers, the article uses chemical methods in the sisal fiber surface silver-plated, untreated, and alkali-treated sisal fibers as a comparison, with the help of scanning electron microscopy, infrared spectroscopy on the fiber surface topography, the molecular structure of the research, determination of high-intensity ultraviolet irradiation under the mechanical tensile properties of the fiber. Exposure to high-intensity ultraviolet radiation for a brief period results in a reduction in the tensile strength, fracture elongation, and elastic modulus of untreated, alkali-treated, and chemically silver-plated sisal fibers by 95.2%, 77.7%, 55.9%, 92.8%, 76.9%, 42.1%, and 89.4%, 70.2%, 34.2%, respectively.

Mechanical properties, permeability and microstructural characterisation of rice husk ash sustainable concrete with the addition of carbon nanotubes

This study investigated the effects of incorporating carbon nanotubes (CNTs) into rice husk ash (RHA) sustainable concrete on its mechanical properties, permeability and microstructure characterisation. Mechanical test results suggested that the addition of 0.10 % multiwalled CNTs (MWCNTs) yielded optimal results, with increases in the compressive strength, splitting tensile strength, flexural strength, and elastic modulus of the RHA concrete at 28 days of 7 %, 23.81 %, 17.5 %, and 1.0 %, respectively. However, with further addition of MWCNTs, the mechanical properties ultimately deteriorated. Further, the incorporation of CNTs enhanced the long-term performance of RHA sustainable concrete. The addition of 0.1 % MWCNTs and 15 % RHA yielded a 20 %, 14 %, and 66 % decrease in water absorption, porosity, and chloride diffusion coefficient compared to the mixture solely containing 15 % RHA. Scanning electron microscopy of this mixture revealed the filling and bridging effects of MWCNTs between the hydration products have enhanced the performance of RHA sustainable concrete.

Peridynamic simulation of micro-internal damage and macro-mechanical properties of cement paste under freeze-thaw cycles

Concrete is a multi-phase, multi-component, heterogeneous composite material and a typical porous medium with a complex microstructure. Under freeze-thaw cycles (FTCs), pressures from the freezing and migration of water within the pores of the concrete cause freeze-thaw damage, which is influenced by its microstructure. To effectively simulate and understand the freeze-thaw damage mechanism, it is crucial to use a geometric structure that reflects the actual pore distribution. This study employs the μic model to create a geometric structure of hardened cement paste, capturing the spatial distribution of pores. The study utilizes the peridynamics (PD) method based on ice formation and crystallization thermodynamics to investigate the freeze-thaw damage evolution and the deterioration of mechanical properties in cement paste under FTCs. The simulations revealed the entire freeze-thaw damage process of cement paste, including internal crack initiation and propagation, as well as surface freeze-thaw spalling. The freeze-thaw damage of cement paste intensifies with increasing FTCs, and the extension of cracks diminishes the interconnection among the skeletons constituting the cement paste microstructure, leading to decreased tensile strength and elastic modulus. Additionally, the stress-strain evolution behavior of freeze-thaw cement paste under uniaxial tensile loads was obtained. The tensile strength and elastic modulus of cement paste decrease with increasing FTCs, and the higher the water-cement (w/c) ratio, the greater the reduction in strength and modulus.

Enhancement of tensile strength and elastic modulus using bio-waste based carbon nanospheres doped polymer nanocomposites

Enhancement of tensile strength and elastic modulus using bio-waste based carbon nanospheres doped polymer nanocomposites

Starch-based films affected by the addition of collagen from Prochilodus magdalenae residues and HPMC: Application in Andean blackberry (Rubus glaucus Benth) coatings.

Starch-based films offer the advantages of biodegradability, edibility, barrier properties, flexibility, and adaptability. This study compared the physicochemical properties of starch-based films by adding raw fish collagen and hydroxypropylmethylcellulose (HPMC). The tensile properties were evaluated, and the interaction with water was analyzed. Barrier properties, such as water vapor and oxygen permeability, were examined, and optical properties, such as gloss and good internal transmittance, were evaluated. The films were evaluated as coatings on Andean blackberries (Rubus glaucus Benth) for 2 weeks at 85% RH and 25°C. The results showed that the inclusion of collagen caused a reduction in the tensile strength and elastic modulus of the films. Also, the formulation with the highest collagen concentration (F7) exhibited the lowest weight loss and water vapor permeability, also it had the highest collagen concentration and showed the highest reduction in Xw and WAC, with values of 0.048 and 0.65 g water/g dry film, respectively. According to analyzing the optical properties, F1 presented the highest bright-ness and transmittance values, with 18GU and 82 nm values, respectively. In general, the films and coatings are alternatives to traditional packaging materials to prolong the shelf life of these fruits.

Lightweight, Strong, and Transparent Wood Films Produced by Capillary Driven Self-Densification.

Wood delignification and densification enable the production of high strength and/or transparent wood materials with exceptional properties. However, processing needs to be more sustainable and besides the chemical delignification treatments, energy intense hot-pressing calls for alternative approaches. Here, this study shows that additional softening of delignified wood via a mild swelling process using an ionic liquid-water mixture enables the densification of tube-line wood cells into layer-by-layer sheet structures without hot-pressing. The natural capillary force induces self-densification in a simple drying process resulting in a transparent wood film. The as-prepared films with ≈150µm thickness possess an optical transmittance ≈70%, while maintaining optical haze >95%. Due to the densely packed sheet structure with a large interfacial area, the reassembled wood film is fivefold stronger and stiffer than the delignified wood in fiber direction. Owing to a low density, the specific tensile strength and elastic modulus are as high as 282MPacm3g-1 and 31GPacm3g-1. A facile and highly energy efficient wood nanotechnology approach are demonstrated toward more sustainable materials and processes by directly converting delignified wood into transparent wood omitting polymeric matrix infiltration or mechanical pressing.

Effect of sodium 2‐acrylamido‐2‐methylpropanesulfonate on the structure and properties of thermoplastic polyvinyl alcohol copolymers

AbstractThermoplastic poly(vinyl alcohol) (PVA) with water‐soluble behavior has received great attention. In this work, a thermoplastic PVA was prepared via solution radical polymerization of vinyl acetate, vinyl pivalate and sodium 2‐acrylamido‐2‐methyl propane sulfonate (SAMPS). The effects of SAMPS content on the structure and properties of modified poly(vinyl alcohol) (MPVA) were investigated. On increasing the proportion of SAMPS, the characteristic band of –OH moved to a larger wavenumber. Compared to PVA, the melting temperature (Tm) of MPVA decreased from 223.1 to 161.5 °C at 0.03 mol of SAMPS, and the initial thermal decomposition temperature (Td) of MPVA increased from 244.3 to 262.2 °C at 0.05 mol of SAMPS. The crystallinity of the resin reduced from 51.46% to 10.21%. The enlarged difference between Td and Tm ensured the preparation of MPVA by thermal processing. The maximum tensile strength and elastic modulus of the obtained sheets were 137.56 and 2639.32 MPa, respectively. The introduction of SAMPS reduced the alcoholysis degree from 99.03% to 95.80%. The high alcoholysis degree of MPVA meant that it could be dissolved in water at 60 °C. This type of thermoplastic PVA shows a promising application on film and textiles that require water solubility. © 2024 Society of Chemical Industry.

Degradation characteristics of 3D printed continuous fibre-reinforced PA6/chopped fibre composites in simulated saltwater

AbstractThis paper investigates the performance of continuous fibre-reinforced 3D printed components in salt water medium at room temperature. Markforged® Mark Two 3D printer was employed to fabricate standard specimens made of Onyx and reinforced Onyx specimens with continuous carbon, high-strength high-temperature glass, and Kevlar fibres. Aging process was conducted to characterize the long-term effect of salt water on the mechanical behaviour of fibre-reinforced 3D printed samples. Several mechanical tests including tensile, 3-point bending test and indentation testing have been carried out on the dry and aged standard samples to evaluate tensile strength, flexural strength, micro-hardness, and modulus of elasticity in micro-scale. The mechanical tests revealed the degradation and loss in mechanical properties of the printed samples after aging in salt water. The data highlighted that Onyx samples without continuous fibres experienced the most significant reduction in both tensile (33.54%) and flexural (63.47%) strengths after 1 year, while continuous carbon fibre-reinforced Onyx samples showed comparatively lower strength reductions (28.46% in tensile strength and 18.73% in flexural strength). Optical and scanning electron microscopy were performed to investigate the fracture behaviour of the tested specimens. In addition, the DSC assessment showed a slight change in the thermal properties of aged specimens.

Physicochemical and antimicrobial characteristics of polypropylene-based nanocomposite containing SiO2-Ag nanoparticles prepared by gamma irradiation

This article evaluates the physicochemical and antimicrobial properties when silver-coated silica (SiO2-Ag) nanoparticles as active nanofiller are incorporated into the polypropylene (PP) thermoplastic matrix. The silica (SiO2) nanoparticles were prepared by precipitation method using sodium silicate. After that, silver-coated silica (SiO2-Ag) nanoparticles were synthesized by gamma radiation technique. X-ray diffraction (XRD), Infrared spectroscopy analysis (FTIR) and Transmission electron microscopy (TEM) analysis clarified the formation of SiO2-Ag nanoparticles. SiO2-Ag nanoparticles has a particle size with an average of 70 nm. The melt mixing procedure operated to fabricate PP thermoplastic nanocomposites with various ratios of 1.0, 2.0, and 3.0 part per hundred resin (phr) of the SiO2-Ag nanoparticles. To examine the effect of ionizing radiation on the prepared PP/SiO2-Ag nanocomposites, the samples were exposed to 20 kGy of gamma-irradiation. FTIR, XRD, mechanical analysis, thermogravimetric analysis (TGA), and scanning electron microscope (SEM) were utilized to characterize the physico-chemical alterations of the PP when loaded with SiO2-Ag nanoparticles. It is found that PP/1.0 phr SiO2-Ag nanocomposite revealed superior physico-chemical characteristics than the other two components. The irradiated specimens revealed superior tensile strength (TS) and elastic modulus (EM) over unirradiated ones, whereas inverse effects were predominant in case elongation at break (E%). Tmax of the native PP increased from 335°C to nearly 370°C of PP/1.0 phr SiO2-Ag nanocomposite. It is established that the fabricated PP/SiO2-Ag nanocomposites exhibited potent antimicrobial activity and can be a good candidate for food packaging applications.

Tensile and compressive properties of bamboo scrimber under different temperature conditions

AbstractBamboo scrimber demonstrates vulnerability to environmental temperature fluctuations, such as exposure to cold or fire, when deployed in structural applications. Consequently, its mechanical properties can substantially diverge from the intended design values under varying thermal conditions. This study aims to study the tensile and compressive properties of bamboo scrimber under different temperatures to provide data support for studying bamboo scrimber under low and high temperatures. The compressive properties of bamboo scrimber under temperatures ranging from −30°C to 250°C and the tensile properties under −20°C to 250°C were determined by a series of tests with a total of 125 specimens. The results show that the mass loss of bamboo scrimber increases gradually with the increase in temperature, and the increasing trend intensifies after 120°C. With the increase of temperature, the failure mode of the specimens under compression changes from the bottom compression cracking damage to the local destabilization of longitudinal fibers, while the tensile damage modes aren't influenced by temperature, and both “straight‐line” and “folded‐line” types of damage modes occur at different temperatures. The tensile and compressive strengths and elastic modulus of the specimens decreased with the increase in temperature, and the strength was more susceptible to the temperature than the elastic modulus: a rise in temperature from 20°C to 250°C resulted in a reduction of compressive strength and tensile strength by 80.80% and 84.11%, respectively, the compressive modulus and tensile modulus experienced decreases of 49.51% and 53.28%. Furthermore, equations of temperature influence coefficients of strength and elastic modulus were established based on the test results.Highlights Bamboo scrimber's mechanical properties under different temperatures are studied. Tendency and explanation of temperature influence coefficients are analyzed. Temperature coefficient equations for strength and elastic modulus are proposed.

Polyimide nanocomposites for high‐temperature capacitive energy storage applications by incorporating functional graphene oxide nanosheets: Design, preparation, and mechanism

AbstractHerein, graphene oxide (GO) and its derivative, reduced GO (rGO) and p‐phenylenediamine (PPD) functionalized GO (GO‐g‐PPD) were first synthesized and selected as dielectric fillers, and then GO/polyimide (PI), rGO/PI, and GO‐g‐PPD/PI dielectric nanocomposites were fabricated through in situ polymerization‐composition strategy. Fourier transform infrared, Ram, and x‐ray diffraction analysis confirmed the success synthesis of rGO and GO‐g‐PPD dielectric fillers. The mechanical properties showed that GO‐g‐PPD/PI nanocomposites exhibited the highest tensile strength and elasticity modulus. TGA analysis revealed that the enhancement of thermal stability by addition of dielectric fillers. The dielectric constant of 2.5 wt.% GO‐g‐PPD/PI nanocomposites reached 25.05, which was 8.55 times that of pure PI (2.93). Energy storage performance tests showed that the energy storage density of GO‐g‐PPD/PI containing 2 wt.% filler reached 0.77 J/cm3, which was 71% higher than pure PI. These findings underscore the potential of GO derivative as a cost‐effective reinforcement for PI dielectric nanocomposites for high‐temperature capacitive energy storage applications.

Experimental Investigation on Durability Properties of Slurry Infiltrated Fiber Concrete

Slurry infiltrated fibrous concrete (SIFCON) can be considered as a special and advanced type of steel fiber reinforced concrete composite. SIFCON is produced by infiltrating rich flow able cement slurry into the bed of preplaced fibers in the mold. In this paper, an attempt has been made to investigate the durability study of SIFCON. An ordinary Portland cement is used with fiber contents of (5%, 7.5%, 10%, and 12%). This study also presents the effect of incorporating Metakaolin (MK) on the mechanical and durability properties of SIFCON for a constant water/cement ratio of 0.5. The physical properties include the specific gravity, density, fineness modulus, water absorption, consistency. The above properties are studied for materials used like cement, fly ash, coarse aggregate, ceramic, sand and laterite. Mechanical properties of the hardened concrete such as compressive strength, tensile strength, flexural strength, and durability properties like water absorption, sorptivity, acid test, marine environment are tested and the values are validated. Metakaolin is a waste/non-conventional material which can be utilized beneficially in the construction industry. From the literature survey, Metakaolin inclusion increases the compressive, tensile, flexural and bend strength and modulus of elasticity of mortar considerably; however, the workability is slightly compromised.

Optimized Functionalization of Graphene Oxide for Enhanced Mechanical Properties in Epoxy Resin Composites

Optimized Functionalization of Graphene Oxide for Enhanced Mechanical Properties in Epoxy Resin Composites