Outlet Air Temperature Research Articles

Simulation and experiment on pneumatic defrosting of evaporators with heat storage

In order to solve the problem of frosting on surface of the evaporators in rapid freezing equipment, a new defrosting system was proposed based on pneumatic defrosting and heat storage defrosting. A three-dimensional flow model including an evaporator and a thermal flow defrosting system was established to observe the temperature distributions of the fins and gas flowing outside the evaporator and to reflect the defrosting effect. The correctness of the model was verified by a freezing experiment. On this basis, the effects of the nozzle placement hole sizes, hot air inlet temperatures and velocities on the fins and cold air temperatures were simulated. The results show that the appropriate horizontal distance between the nozzle and the evaporator is 40 mm considering the large area of heat transfer. The initial temperatures of the hot gas and nozzle sizes have little effects on the heat exchange areas, but the initial velocities of the hot gas have great effects on the heat exchange areas. It takes 180 s for the air outlet temperature of the heat accumulator with the decrease of the temperature from 44 °C to 25 °C. The frost on the surface of the fin melts rapidly within the time that the heat accumulator can maintain a certain temperature range. More studies are required to perform defrosting experiments by choosing appropriate heat storage materials and elevating gas pressure and temperature.

The effect of the fluidized bed agglomeration process on the powder properties of black carrot juice powders

AbstractThis study aims to apply fluidized bed agglomeration process performed at 60°C and 1.6 m/s as air temperature and velocity, to improve the powder properties of the black carrot juice powders obtained by spray drying at the inlet and outlet air temperatures of 160 and 100°C, respectively. The binders maltodextrin, gum arabic, whey protein isolate and water were added to the powders at 1:0.1, and 1:0.2 powder/binder solution (BS) ratios. The agglomerates have higher moisture content (11.35%–12.88%, wet basis) and water activity (0.256–0.379) values than the powders (9.18 ± 0.03% and 0.25 ± 0.00, respectively). While the angle of repose value of black carrot juice agglomerates decreased compared to powders, the porosity values (54.17%–66.87%) and the hygroscopic properties were improved. The friability values for the agglomerates were 37.21%–77.04%. The agglomeration process improved the microstructure, glass transition temperature and particle size distribution as determined with scanning electron microscope, differential scanning calorimeter, and laser diffraction method analysis.Practical applicationsBlack carrot is a vegetable with high nutritional value and its consumption is limited to a certain season. For this reason, the production of the powders of vegetable juices and having the agglomerated form of them, an important improvement will be achieved in the production of healthy and easy to use foods for children and adults. Fluidized bed agglomeration which is a novel application is important in the creation of easy‐to‐use meals. Black carrot juice powders could be successfully agglomerated with some different binders in fluidized beds. Powder properties of agglomerates containing water were as good as the binder agents.

Performance evaluation of a solar photovoltaic-thermal (PV/T) air collector system

In the present study, the performance of a photovoltaic-thermal (PV/T) air collector is evaluated by revealing the temperature distribution and investigating the effect of the inlet and outlet air temperature and PV cell temperature. Solar PV/T collectors have been recently introduced as a promising solution for the global energy crisis. There is a lack of literature investigating the effect of changing duct depth and velocity, which this study explores. Two scenarios are considered: a PV system and a PV/T system. Equations for efficiency are derived based on thermal and electrical parameters. The simulation results were validated by a set of experimental results from a similar PV/T set-up. Simulations were carried out to a high degree of accuracy with ‘R’ values ranging between 0.881 and 0.952. The air duct improved the electrical efficiency of the PV module by 13.67 %. The PV/T system improved efficiency while limiting its variance throughout the day. It was found that increasing the duct depth reduced the electrical and thermal efficiency. The efficiency of the system improved with rising duct air velocity. Ideal design parameters were identified with a duct depth of 0.01 m and a duct air velocity of 2.5 m/s.

Techno-economic analysis of an indirect solar dryer with thermal energy storage: An approach with machine learning algorithms for decision making

Machine learning models effectively forecast and improve engineering systems as solar dryers, making them valuable replacements for traditional physics-based models. Also, according to the literature, there is a research gap in solar drying regarding the lack of a comprehensive comparison of machine learning algorithms, neglecting the importance of cross-validation and tuning parameters. Therefore, this research focuses on employing machine learning models as effective surrogate models for solar dryers that attend to this gap, reducing the computational burden. A methodology for developing and comparing machine learning surrogate models of three indirect solar drying technologies (conventional, energy storage with beach sand, and storage with limestone) is proposed. The algorithms were trained using the database generated from a tomato solar drying process, where the solar dryer type, solar irradiance, ambient temperature, wind velocity, and relative humidity were considered model inputs to estimate the absorber plate, solar collector outlet air, and drying chamber outlet air temperatures. Subsequently, from the best predictive algorithm, a techno-economic analysis was conducted annually. The results revealed a high accuracy (R2 of 0.9917) and similar values regarding metrics that measure precision and variance. The solar dryer with thermal energy storage using beach sand exhibited the highest thermal and drying efficiency values (52.52 % and 12.57 %, respectively), while the limestone variant reported the shortest drying time (22 h). The economic evaluation indicated minimal monetary loss (3.09 %) compared to the current system’s annual projection. Finally, the framework presented in this research emphasizes using machine learning models to forecast the system’s energetic and economic performance indicators and contributes as a substitute for experimental studies that involve high cost and long duration. This work lays the bases and guides future research where machine learning algorithms are needed to compare energetic systems’ best computational and techno-economic performance.

Alternative Approaches for Real-time Monitoring of the Effectiveness of Hydrogenerator Heat Exchangers

Heat exchangers require periodic maintenance. Offline cleaning scheduled shutdowns are usually needed to restore the exchanger effectiveness, drastically reduced when fouling accumulation occurs. An online real-time alternative for monitoring the effectiveness of exchanger (during a period of eleven months of continuous operation) and an adapted version of the ε-NTU method to calculate its effectiveness are discussed. The experimental difficulties of measuring the mass flow rate and the hot air temperature at the exit of the exchanger is examined. Detailed analysis confirmed that the outlet temperature of the hot fluid could introduce errors of up to 30% in the calculation of the exchanger effectiveness. A skillful treatment of the energy balance is proposed to address the issue. The associated uncertainties are estimated by two independent approaches, the so-called classic method, i.e., the Guide to the Expression of Uncertainty in Measurement and the Monte Carlo method. Both confirmed that measurements of the air outlet temperature accounts for more than 50% of the uncertainty associated with the calculation of the exchanger effectiveness. It is suggested that the conventional method (based on measurements of the outlet air temperature) is not suitable for traditional everyday practices to monitor the effectiveness of the heat exchangers of hydrogenerators.

Experimental and numerical study of a natural convection indirect solar dryer with PCM tubes: Dynamic, thermal and nutritional quality analysis

A natural convection solar dryer was investigated in this paper with a storage unit in the form of copper tubes filled with Paraffin wax as a PCM, experimentally and numerically using the ANSYS Fluent software. The storage unit was placed in a side-mounted plenum chamber for air uniformity and heat recovery. The validations made for the drying chamber’s temperature with and without storage, the outlet air temperature, and velocity of the SAH, show good accordance with the experimental results, which promote the use of this method in investigating the solar dryer numerically. The drying of orange slices in different modes were studied; open sun drying, in a solar dryer with and without PCM. The drying time required to reduce the moisture content from 81.19% (wb) to 19% (wb) was respectively 216 h, 144 h, and 168 h. In terms of the quality of orange slices, the open sun drying showed the poorest quality in terms of color, texture, shape, and odor. However, all these properties were enhanced with the solar dryer, particularly with the use of PCM tubes. The most valuable nutritional value of oranges is vitamin C, which was measured per slice in all mentioned cases. One fresh orange slice contains 11.34 mg of vitamin C, while it contains 7.77 mg, 7.34 mg, and 5.99 mg in the drying cases with and without PCM as well as in open sun drying respectively.

Energetic and exergetic performance analysis of finned plate solar air heater integrated with PCM-aluminium chips composite as heat storage system

ABSTRACT In this experimental work, the effect of combining a finned absorber solar air heater (FSAH) with PCM-aluminum chips composite on enhancing its thermal response is experimentally investigated based on energy and exergy standpoints. Experiments are conducted to compare the thermal response of FSAH using PCM-aluminum chips composite against the FSAH with no PCM and with PCM only, under weather circumstances in Baghdad city, Iraq. The thermal response factors of the proposed FSAH are examined for varying air mass flow rates, such as 0.009, 0.029, and 0.061 kg/s, and constant PCM’s mass. The results reveal that against the FSAH with no PCM, the energy heat gain of FSAH with PCM is only increased by 65.1% and its energy and exergy efficiencies are increased by 55% and 12%. Meanwhile, the inclusion of an aluminum chips within the PCM is found to be the best configuration among all the tested cases, providing an outlet air temperature for a long duration time of about 2.25 hr compared to FSAH with no PCM. In addition, the energy heat gain is increased by 115.4% and its energy and exergy efficiencies are increased by 168% and 123%, respectively, which is suitable for agricultural drying and space heating operations.

Phonon-Engineered Hard-Carbon Nanoflorets Achieving Rapid and Efficient Solar-Thermal Based Water Evaporation and Space-Heating.

Generation and utilization of green heat produced from solar energy demand broadband absorbers with the elusive combination of strong phonon-driven photon thermalization and, contrastingly, weak phonon-lattice thermal conductivity. Here, we report a new class of porous, nanostructured hard-carbon florets (NCFs) consisting of isotropically assembled conical microcavities for greater light entrapment and efficient broad-band absorption (95% over 250-2500 nm). Resembling marigolds, the NCF exhibits short-range graphitic order that promotes instantaneous and efficient solar-thermal conversion (ηSTC = 87%) while exhibiting long-range intrinsic disorder providing low thermal conductivity (1.5 W m-1 K-1) to minimize thermal loss (13%). Solution processable NCF coatings on arbitrarily substrates (filter paper, terracotta, Cu and Al tubes) generate surface temperature of 400 ± 2 K and exhibit high thermal effusance (519 W s0.5 m-2 K-1) to achieve highest combination of (a) rate of solar-driven interfacial water evaporation (Rw = 5.4 kg m-2 h-1, 2 sun), (b) solar-vapor conversion efficiency (ηSVC = 186%), and (c) ηSTC (87%) among known materials. Such robust performance is retained for beyond 30 days of continuous operation and under different solar power (1 sun to 5 sun). Furthermore, active space heating (outlet air temperature = 346 ± 3 K) using NCF coatings is demonstrated.

The energy performances of an elastocaloric device for air conditioning through numerical investigation

The urgent needing to address global warming and the rapid depletion of fossil fuel reserves has led to a demand for immediate research in sustainable and clean energy technologies. Elastocaloric cooling is a promising proposal for clean refrigeration because of the zero global warming potential of the shape memory alloys, which are solid-state materials showing elastocaloric effect. The latter manifests when the shape memory alloys are stressed through a mechanical loading, transforming from the austenite phase toward the martensite one and releasing heat, dually transforming from the martensite phase into the austenite phase and absorbing heat. The updated literature accounts for 15 elastocaloric cooling devices, but none is close to commercialization. The efforts are devoted to making this decisive step by implementing new efficient devices.This paper analyses the energy performances of an elastocaloric rotary prototype employing binary NiTi wires through the first rotary bidimensional numerical model based on the finite element method to attain the device's potential cooling and heating capacities. In this paper, the energy performances of an elastocaloric rotary prototype employing binary NiTi wires are analyzed through a 2D numerical model based on the finite element method to attain the device's potential cooling and heating capacities. The model reproduces the thermo-fluid-dynamic behaviour of an experimental rotary device for air conditioning; meanwhile, the secondary fluid in the device is air. The accuracy of the rotary model easily allows to optimize the operating parameters of the elastocaloric prototype under construction.Results in terms of outlet air temperature, cooling power and coefficient of performance are presented for different air velocities inside the air channel and different rotation frequencies of the device. A performance map has been obtained by exploring the device's behaviour in the cooling mode under variable working conditions to identify the optimal configuration. A maximum COP of 6.22 (corresponding to a second law analysis efficiency of 60%) was evaluated under an airflow speed of 6 m s−1 and a frequency of 0.3 Hz, corresponding to ϕ∗=0.44. 28.5 K and 5400 W kg−1 are the reached peaks of temperature span and cooling power.

Experimental and energy saving potential analysis of GSHP and ASAC systems using normalized sensitivity technique in cooling mode operation

ABSTRACT The current investigation examines the experimental and energy-conservation analyses of 17.5 kW cooling capacity of a ground-source heat pump (GSHP) system and an air-source air-conditioning system (ASAC) of the same cooling capacity. Using experimental data and a sensitivity technique, the thermal efficiency of both the systems were evaluated. During the experiments conducted for cooling period in June 2022, the data for six-day operation were collected and the coefficient of performance of both the systems were evaluated. Notably, the GSHP system exhibited an average cooling capacity of 10 to 15 kW, whereas the ASAC maintained a range of 9 and 13 kW. The coefficient of performance (COP) for the GSHP system was obtained as 3.8, while the ASAC system COP was 2.9. The results indicate that the use of GSHP system results in an energy-saving of 10–40% in comparison to the ASAC system. Moreover, the present study included uncertainty and propagation analyses, along with sensitivity evaluations, with the objective of identifying the most influencing parameter on the derived parameters. Sensitivity analysis indicates outlet temperature of air from the evaporator is the most influencing parameter for the performance of both the systems.

Numerical investigation of the discharging process in a latent cold storage unit

In this study, a latent cold storage unit using vertical cylindrical structure coupled with a concentric air duct is proposed. The cold discharging process of the unit is simulated by computational fluid dynamics (CFD) based on the enthalpy-porosity method. The temperature distribution and liquid fraction distribution of the latent cold storage unit are analyzed. In addition, thermal performance including the average temperature of phase change material, outlet air temperature, the liquid fraction and the cold discharging power are analyzed in detail.

Natural convection and structural impact of rectangular PCM storage units through the modular expansion

To increase the storage capacity and air flow rate of the rectangular thermal energy storage unit (RTESU) for enhancing its application capability, three modular units with air flow rates of 60 m3/h, 120 m3/h, and 180 m3/h for heights of 150 mm, 300 mm, and 450 mm are proposed. Besides, the effect of natural convection (NC) on the charging and discharging process is examined during the modular expansion of the RTESU. The melting performance including melting duration and phase change process is numerically investigated by varying the configurations such as module configuration, non-uniform, and eccentric tube arrangements. The results show that NC has a significant impact on the charging process. It is further demonstrated that the charging process can be enhanced by about 14.58 % and 13.61 % when non-uniform and eccentric tube arrangements are implemented, respectively, as they both increase the area dominated by NC. However, the non-uniform tube arrangement for acceleration of the melting process is gradually enhanced with the increase in storage unit height compared to that of the eccentric tube arrangement. It is worth noting that the Nusselt number (Nu) is introduced for examining heat transfer performance during the melting process with different unit configurations. And the correlation between the dimensionless numbers is applied to predict the liquid fraction for different configurations. For the heat release process, the performance including air outlet temperature, heat extraction, and heat release efficiency of the modular RTESU is evaluated. It is found that the NC has a negligible effect on the discharging process, which is dominated by heat conduction. With the modular expansion, an increase in air flow rate and heat storage capacity as well as the maintenance of a higher heat release efficiency of about 84.97 % can be achieved in the RTESU.

Study on Effects of Operating Parameters on a Water-Cooled Loop Thermosyphon System under Partial Server Utilization

During the operation of a data center, servers are gradually installed in racks, causing most racks to work under a low heating load for a long time and affecting the cooling efficiency of the loop thermosyphon system (LTS). Thus, the effects of operating parameters on the thermal performance should be investigated. In this study, a water-cooled LTS was experimentally investigated under different airflow rates and heating loads. The results show that the additional liquid refrigerant reduced the heat transfer performance and aggravated a drop in cooling capacity when the airflow rate and heating load were decreased. To further reveal the effects of the operating parameters on the thermal performance and cooling efficiency, a steady-state distributed-parameter model was developed and validated based on the experimental data. The results show that the excessive cooling capacity was reduced by decreasing the airflow rate according to the upper limit of the server exhaust air temperature under partial server utilization. The excessive cooling capacity was reduced by 14.5–52.1% under 5–56.5% server utilization. To further reduce the excessive cooling capacity while ensuring thermal security, the water side operating parameters (including the supply chilled water temperature and water flow rate) were adjusted according to the upper limit of the rack’s average outlet air temperature, which reduced the excessive cooling capacity by more than 23.8% under partial server utilization.

Design, CFD Simulation, Prototype, and Experimental Investigation of Indirect Active Solar Dryer for Banana

Indirect active tray solar dryer was designed, CFD simulated, and constructed for the drying of banana in Addis Ababa, Ethiopia. The experimental investigation was done after the CFD ANSYS Fluent simulation of different parameters based on the uniformity temperature and air flow distributions on the symmetry plane. The performance of the designed solar dryer was compared with that of the open sun dryer method, based on drying rate, moisture ratio, and moisture content on a wet and dry basis. From fourteen different mathematical drying thin layer kinetics models, the maximum correlation coefficient of 0.999574, the minimum root mean square of 0.0001352, and the minimum reduced chi-square of 0.007353 were obtained for the Verma et al. model for the slice banana in the designed active solar dryer. Recycling the air from the outlet of the drying chamber on the first day is not possible because the quality of the air is lower when compared with ambient air. The outlet air temperature and relative humidity of the drying chamber were 4.39℃ higher and 8.24% lower than the ambient air temperature and relative humidity respectively, so it is possible to recycle the air after the first day. The average moisture content removed from the product in the designed solar dryer and open sun dryer was 68.01% and 51.01%, respectively, in the 22 and half5 drying hour. The difference between the maximum and minimum moisture removal was 4.47%. It indicates there is a uniform drying in the designed solar dryer. The overall solar air collector efficiency was 33.80%and the maximum drying efficiency was 31.10 %.

Circuitry optimization using genetic programming for the advancement of next generation refrigerants

In this study, a new evolutionary method, which can handle the implementation of genetic operators with unrestrained number and locations of splitting and merging nodes for the optimization of heat exchanger circuitries, is developed. Accordingly, this technique expands the search space of previous optimization studies. To this end, a finned-tube heat exchanger simulator is structured around a bijective mathematical representation of a refrigerant circuitry (the tube–tube adjacency matrix), which is used in combination with traversing algorithms from graph theory to recognize infeasible circuitries and constrain the evolutionary search to coherent and feasible offspring. The performance of three refrigerants, namely R32, R410A, and R454C, commonly used in air-conditioning applications was assessed for the optimized circuitries of a 36-tube evaporator while converging to a given cooling capacity, degree of superheating, and heat source boundary conditions. At a given output capacity and air outlet temperature, larger coefficient-of-performance improvements (up to 9.99% with reference to a common serpentine configuration) were realized for zeotropic refrigerant mixtures, such as R454C, where appropriate matching of the temperature glide with the temperature variation of the air yielded the possibility of further reducing the required compression ratio under the corresponding operating conditions. Hence, it was demonstrated that low-GWP zeotropic mixtures with temperature glide can realize a performance comparable to that of R32 and higher than that of R410A by approaching the Lorenz cycle operation.

Effect of different concentrations of thermoprotectant on microencapsulation of Lactobacillus rhamnosus GG by spray-drying, and its effect on physicochemical properties and viability

Lactobacillus rhamnosus GG (LGG) is an acceptable probiotic strain that can live and grow at a gastrointestinal acidic pH and on a bile-rich medium. The influence of spray-drying microencapsulation of LGG on the physicochemical parameters and survivability was investigated in the present work. LGG was spray-dried with three different maltodextrin concentrations (6, 12, and 18% w/v). The inlet and outlet air temperatures of the spray-dryer were kept at 170 ± 5°C and 75 ± 5°C, respectively. The physicochemical parameters (moisture content (wet basis), water activity, and colour), viability (colony forming unit/g), and simulated gastrointestinal digestion were all investigated. Only 18% MD was selected on the basis of moisture content and log CFU/g. The total soluble solids (TSS) of 16.28 ± 0.93 °Brix were obtained using 18% MD. The end product had a moisture content of 5.40 ± 0.20%, and a water activity of 0.32 ± 0.02 aw, which were acceptable. The L*, a*, and b* of the final product were 95.14 ± 0.19, -2.33 ± 0.02, and 7.17 ± 0.13, respectively. The spray-dried powder had final probiotic viability of around 108 CFU/g. Based on the study, maltodextrin at 18% (w/v) concentration can be considered as an ideal formulation with acceptable powder characteristics for shielding probiotic microorganisms from harmful conditions of spray-drying.

An Experimental Study omn Evaporative Condenser in Air Conditioning Systems Using R744

Nowadays, the use of refrigerants has low GWP and zero ODP applying refrigeration and air conditioning systems is an important concern. There has been a lot of research taking about refrigeration systems using R744. In this study, we focus on the use of the mix of water and air for an evaporative condenser through an experiment to study the heat transfer efficiency between water and the R744. The results of this study show that it is feasible to use water to cool down R744 to a subcritical state. The data obtained show that the R744 temperature at the outlet condenser gradually decreases with each change in the number of tube layers, the condensing pressure is stable at 73 bar with a pressure drop of 0.4 bar. The water temperature is stable between 26oC and 28oC, and the air outlet temperature from the indoor unit gradually decreases from 28oC to 16.8oC. With the 3 configurations of the condenser, the coefficient of performance gradually increases from 3.6 to 4.5 respectively.

Study on Heat Transfer Performance and Parameter Improvement of Gravity-Assisted Heat Pipe Heat Transfer Unit for Waste Heat Recovery from Mine Return Air

One of the effective methods for energy conservation and emission reduction in coal mines is to utilize waste heat recovery technology to recover mine return air waste heat. The gravity heat pipe is widely used in mine return air waste heat recovery due to its sustainable and economic advantages, but its heat transfer is a complex process influenced by multiple parameters. A single-tube heat transfer resistance model and a heat transfer calculation model based on enthalpy difference were established for the heat exchange tubes. Four typical application cases of a low flow rate and a low number of tube rows were selected, and their heat transfer characteristics were tested onsite and analyzed. It was found that there were problems such as a low overall heat transfer efficiency, a low fresh air outlet temperature, and a risk of icing in the final tube section. The effects of the gravity heat pipe parameters on the heat transfer performance were studied, such as the tube outer diameter, tube spacing, and the finned tube outer diameter. It was found that the air-resistant force of the heat exchanger increased with the increase of the tube spacing and the finned tube outer diameter, the heat transfer resistance increased with the increase of the tube spacing and the decrease of the finned tube outer diameter, and the heat transfer coefficient first increased and then decreased with the increase of the tube outer diameter. A configuration improvement scheme with a high flow rate and a high number of tube rows is proposed here. Taking Case 2 as an example, the temperature distribution of the heat tube before and after improvement is compared and analyzed. The results show that the heat transfer performance of the heat exchange system significantly improved. Without increasing the air resistance of the heat tube, the temperature of the return air outlet after improvement was reduced to 1.1 °C, 4.1 °C lower than that before improvement, further recovering the waste heat of the mine return air. The temperature of the condensate water film was greater than 0.5 °C, avoiding the icing problem of the condensate tube section, the fresh air outlet temperature reached 5.2 °C, an increase of 7.8 °C compared to that before improvement, and the overall heat transfer efficiency increased from 56.7% to 66%.

A conceptual evaluation of cross-flow membrane contactor for desalination process

The current work objectives are providing detailed understanding of heat and mass transport in a cross-flow membrane contactor for desalination process. The numerical code was developed using MATLAB software to investigate temperature and humidity distribution in the cross-flow membrane contactor at different operating parameters. Firstly, the developed model was successfully validated by experimental data. It was found that increase in saline solution inlet temperature from 40 °C to 80 °C can enhance solution outlet temperature, outlet air temperature, and humidity of outlet air from 37.38 °C to 56.79 °C, 39.48 °C–72.33 °C, and 0.0393 kg/kg to 0.2620 kg/kg respectively. Furthermore, the results showed that increase in saline solution flowrate and its inlet temperature has significant influence on the improvement of the process performance in terms of producing more pure water. However, there was no effect on temperature and humidity profiles, vapour transport though microporous membrane with the enhancement of inlet humidity of air. It was only had small positive influence on humidity humidification efficiency at inlet temperatures in the range of 40 °C–80 °C.

Design and Performance Analysis of a Solar Air (SA) Heater with Phase Change Material (PCM) Heat Storage for Residential Applications

Outlet air temperature can be seen as one of the main determinants of the functioning of the solar air heaters and this is one of the main features of the PCM. Variations in solar radiation can be considered a key determinant of the functioning of solar air heaters used in residential applications. Weather conditions can influence the presentation of the air heaters operated by solar energy to a great extent. Structuring of collector plates needs to be done in an effective manner by designers of air heaters used in residential applications. The contact surface of the collector plates is the other determinant of the presentation of the air heaters. A blower is one of the most vital components used in air heaters and the efficiency of the blower can improve the execution of this device. Transport fluid has been identified as a vital factor that can have a huge impact on the functioning of air heaters operated by solar energy. Air thermal capacity can be considered as the other determinant of the functioning of this device. The high cost of fluid circulation has been found as one of the negative factors in the structure and functioning of the air heaters used in residential applications.