Effect Of Temperature Research Articles

Effect of temperature and strain rate on the hot workability behaviour of Ni–25Cr–14W superalloy: An approach using processing map and constitutive equation

Effect of temperature and strain rate on the hot workability behaviour of Ni–25Cr–14W superalloy: An approach using processing map and constitutive equation

Effect of temperature on the stability and performance of III-nitride HEMT magnetic field sensors

The study aimed to investigate the underlying physics limiting the temperature stability and performance of non-surface passivated Al0.34Ga0.66N/GaN Hall effect sensors, including contacts, under atmospheric conditions. The results obtained from analyzing the microstructural evolution in the Al0.34Ga0.66N/GaN Hall sensor heterostructure were found to correlate with the electrical performance of the Hall effect sensor. High-resolution x-ray photoelectron spectroscopy studies revealed the signature of surface oxidation in the GaN cap layer, as well as a slight out-diffusion of “Al” from the AlGaN barrier layer. To prevent the formation of a bumpy surface morphology at the Ohmic contact, we investigated the impact of “Pt” top Ohmic contacts. The application of a top “Pt” contact stack resulted in a smooth Ohmic contact surface and provided evidence that the bumpy surface morphology in Au-based Ohmic contacts is due to the formation of an Al-Au viscous alloy during rapid thermal annealing. In the early stages of thermal aging, the small drop in contact resistivity stabilized with subsequent thermal aging past the initial 550 h at 200 °C. The outcome is that the Al0.34Ga0.66N/GaN Hall effect sensors, even without surface passivation, exhibited a stable response to applied magnetic fields with no sign of significant degradation after 2800 h of thermal aging at 200 °C under atmospheric conditions. This observed stability in the Hall sensor without surface passivation can be attributed to a self-imposed surface oxidation of the cap layer during the early stages of aging, which serves as a protective layer for the device during subsequent extended periods of thermal aging at 200 °C.

Implications of ocean warming and acidification on heavy metals in surface seawater of the Bohai Sea

At present, a clear dependency of the dynamics upon temperature and pH has not been established for many heavy metals (HMs), so making it difficult to project and quantify the impact of ocean warming and acidification on metal biogeochemistry in future scenarios. To understand the responses of HMs to future ocean warming and acidification, we estimated the spatial-temporal variations and pollution status of six dissolved HMs (i.e., Cu, Zn, Pb, Cd, Hg, and As) in surface seawater throughout the Bohai Sea during 2012–2014. The results showed that the average concentrations of Cu, Zn, Pb, Cd, Hg, and As in seawater of the Bohai Sea were between 2.01–3.18, 10.47–15.58, 0.85–2.31, 0.25–0.55, 0.05–0.13, and 1.24–1.98 μg L-1, respectively. Spatially, the average concentrations of the studied HMs generally decreased from the three bays towards the central area, except for Hg which was relatively high in the central Bohai Sea in some cases. This implied that, in addition to continental inputs, there may be other processes affecting the distribution pattern of Hg, such as cyclonic or anticyclonic gyres, benthic fluxes between surface and bottom layers, and some marine planktonic and microbial activities. The pollution assessments of six HMs in seawater revealed that the major risk pollutants were Pb and Hg across the Bohai Sea. Analyses of the local and interactive effects of temperature and pH on HMs showed that the interactive effect of changing temperature and pH on HMs is much more complex than a direct temperature/pH relationship with HMs. Altogether, the results suggested that future ocean warming and acidification will significantly influence the concentrations of dissolved HMs in seawater of the Bohai Sea, but with different relationships.

Development of a TGC-based growth model for the olive flounder, Paralichthys olivaceus, and its application in developing a fish growth simulator architecture

Temperature is one of the main factors affecting fish growth. Many studies have proposed a fish growth model considering the effect of temperature. Among these models, the TGC (thermal growth coefficient) model which digitized the influence of temperature on fish growth is the most notable. The original TGC model was made in the form of applying 1/3 as an exponent, but subsequent studies have shown that it is necessary to apply different exponent value or other constant depending on the dynamics of growth. In this study, the original TGC model using 1/3 as an exponent and the new model using 2/3 as an exponent were compared for olive flounder (Paralichthys olivaceus). The seasonal temperature function under the conditions of the flow-through system was applied and the transition point of change in the growth dynamics was obtained by comparing the instantaneous growth rate of the two TGC models. Around 541 g of the transition point was obtained, and a combined TGC model was presented that integrated the two models. However, the growth prediction model based on these statistical techniques does not reflect real-time changes in each parameter and requires academic knowledge, making it difficult to use in the actual field. Recently, as the smart aquaculture industry incorporating ICT (information and communication technologies) has grown rapidly, many solutions such as fish growth prediction simulators using statistical growth models have been developed. Therefore, in this study, input and output variables were classified and software architectures were presented so that the statistical form of fish growth model using TGC derived above could be applied when developing a fish growth prediction simulator. Deriving these growth models and interpreting them into languages in the field of ICT will enhance the field applicability of academic research results as a part of smart aquaculture technology.

Study of Different Parameters on Removal of Methyl Violet Dye Using Coconut Shell Powder as an Adsorbent

The dyeing business is one of the most water- intensive industries. The effluent from the dyeing industry comprises a variety of chemicals and coloring compounds, and it must be properly treated before being dumped into any water body. However, dye house effluents are extremely difficult to treat properly because to their considerable variability in composition. In most cases, a combination of multiple techniques of treatment is required to eliminate all toxins from the wastewater. As a result, adsorption became one of the most efficient ways for removing color from textile effluent. In this paper, an attempt is made to remove the colored ingredient Methyl Violet present in the colored solution by using a cheaply available adsorbent, coconut shell powder of specific size. In this work, the effect of variation in the parameters like dosage of adsorbent, temperature of the solution and initial concentration of the solution are studied and the adsorption removal efficiency is studied through an experimental approach. The adsorbent used is dry coconut shell of size -100 BSS mesh number. The dosage of adsorbent was varied from 10 gms to 50 gms and It was discovered that the adsorption removal efficiency was varying between 72.9 % to 89.6 %. The Additional factors that were examined are effect of temperature on adsorption and effect of initial concentration. The temperatures varying from 500C to 700C. It was determined that the adsorption removal effectiveness of Methyl Violet was found out to be decreasing from 64.6 % at 500C to 47.9 % at 700C. Adsorption efficiency was shown to decrease as temperature increased. The initial adsorbent concentration ranged from 30 to 70 ppm. It was shown that increasing the starting concentration enhanced the adsorption removal effectiveness from 85% to 88%. Based on the results of the preceding experiments, it is possible to infer that coconut shell powder is an efficient adsorbent for removing Methyl Violet from waste water, with an 89.6% removal rate.

Timing-dependent effects of elevated temperature on reproductive traits in the European corn borer moth.

Elevated temperature often has life stage-specific effects on ectotherms because thermal tolerance varies throughout ontogeny. Impacts of elevated temperature may extend beyond the exposed life stage, if developmental plasticity causes early exposure to carry over, or if exposure at multiple life stages cumulatively produces effects. Reproductive traits may be sensitive to different thermal environments experienced during development, but such effects have not been comprehensively measured in Lepidoptera. In this study, we investigate how elevated temperature at different life stages alters reproduction in the European corn borer moth, Ostrinia nubilalis. We tested effects of exposure to elevated temperature (28°C) separately or additively during larval, pupal, and adult life stages compared to control temperatures (23°C). We found that exposure to elevated pupal and adult temperature decreased the number of egg clusters produced, but exposure limited to a single stage did not significantly impact reproductive output. Furthermore, elevated temperature during the pupal stage led to a faster transition to the adult stage and elevated larval temperature altered synchrony of adult eclosion, either by itself or combined with pupal temperature exposure. These results suggest that exposure to elevated temperature during development alters reproduction in corn borers in multiple ways, including through carry-over and additive effects. Additive effects of temperature across life stages are thought to be less common than stage-specific or carry-over effects, but our results suggest thermal environments experienced at all life stages need to be considered when predicting reproductive responses of insects to heatwaves.

Formation and desorption of sulfur chains (H2Sx and Sx) in cometary ice: Effects of ice composition and temperature

Abstract The reservoir of sulfur accounting for sulfur depletion in the gas of dense clouds and circumstellar regions is still unclear. One possibility is the formation of sulfur chains, which would be difficult to detect by spectroscopic techniques. This work explores the formation of sulfur chains experimentally, both in pure H2S ice samples and in H2O:H2S ice mixtures. An ultra-high vacuum chamber, ISAC, eqquipped with FTIR and QMS, was used for the experiments. Our results show that the formation of H2Sx species is efficient, not only in pure H2S ice samples, but also in water-rich ice samples. Large sulfur chains are formed more efficiently at low temperatures (≈10 K), while high temperatures (≈50 K) favour the formation of short sulfur chains. Mass spectra of H2Sx, x = 2-6, species are presented for the first time. Their analysis suggests that H2Sx species are favoured in comparison with Sx chains. Nevertheless, the detection of several S$_x^+$ fragments at high temperatures in H2S:H2O ice mixtures suggests the presence of S8 in the irradiated ice samples, which could sublimate from 260 K. ROSINA instrument data from the cometary Rosetta mission detected mass-to-charge ratios 96 and 128. Comparing these detections with our experiments, we propose two alternatives: 1) H2S4 and H2S5 to be responsible of those S$_3^+$ and S$_4^+$ cations, respectively, or 2) S8 species, sublimating and being fragmented in the mass spectrometer. If S8 is the parent molecule, then S$_5^+$ and S$_6^+$ cations could be also detected in future missions by broadening the mass spectrometer range.

Effect of different temperature–time combinations on the quality and protein digestive properties of stewed beef tendons

This study investigated the effects of sous vide cooking and traditional high-temperature cooking on the texture, microstructure, protein structure and digestive properties of home made beef tendon using transmission electron microscopy, in vitro digestion and peptidomics. The adverse effects of heating on the muscle fiber structure and protein conformation of beef tendon gradually expanded with increasing temperature. In general, the degree of muscle fiber contraction, protein denaturation, and protein aggregation increases with temperature and time, with a concomitant decrease in protease action. The extent of protein digestion, and the yield of small fragments such as amino acids also decreased with increasing heating temperature and time. However, the solubilization of collagen makes the beef collagen more digestible after heating at 80°C, which indirectly leads to higher digestibility at 80°C. The combined peptide release and bioactive peptide results showed that the beef tendon heated at 60°C for 8 h produced the most peptides after digestion, and also produced four specific bioactive peptides, which were advantageous in terms of the number of digested products and bioactivity. The higher proportion of antioxidant amino acids in the product also gave the tendon heated at 60°C for 8 h a greater potential antioxidant capacity. As a result, beef tendon heated at 60°C for 8 h is more favorable for human digestion. This work may provide guidance for home cooking and dietary health.

The effect of operating conditions on heat transfer for parallel plate heat exchangers of thermoacoustic standing wave systems

Thermoacoustic systems represent a promising technology for clean cooling and/or power generation. However, understanding of the behavior of oscillatory flow inside the system under high drive ratio operating conditions, at elevated mean pressures, range of frequencies, and high flow amplitudes, remains limited and poses challenges for designing efficient systems with minimal losses. This paper presents a numerical investigation into the flow and heat transfer characteristics across a coupled cold and hot parallel-plate heat exchanger operating under standing-wave type oscillatory flow conditions. The models were developed for various conditions, spanning frequencies from 13 Hz to 100 Hz and mean pressures between 1 and 20 bar, using both nitrogen and helium as working fluids. The study reveals significant phenomena such as heat accumulation and annular effects in both temperature and velocity/vorticity fields. These findings were discussed in the context of their impact on the heat transfer performance of the heat exchanger. Specifically, the emergence of vortices was examined in relation to mean pressure, alongside jet-like velocity profiles and natural convection effects. Furthermore, the paper includes a comparative analysis between the heat transfer model employed in this study and previous works, aiming to validate the findings. This research enhances the understanding of fluid dynamics and heat transfer phenomena within heat exchangers of thermoacoustic devices, thereby contributing to advancements in future design improvements.

Removal of Phosphate and Ammonium Ion from Domestic Wastewater Using Clay Feldspar in Wupa Sewage Treatment Plant Abuja

The aim of this study is centered on the sustainability of feldspar as an adsorbent as opposed to other clay minerals such as plastic clay, red clay and barite. Brauner-Emmert-Teller (BET) analysis of the clay minerals considered in this study revealed that raw feldspar had the highest surface area and pore volume of 332.8 m²/g and 0.218 cc/g respectively. Similarly, the clay minerals were used in adsorption study with feldspar producing the best removal efficiency of 90.00%and 73.96% for ammonium and phosphate ions respectively. The BET results and the adsorption test showed that feldspar was a better adsorbent than the other adsorbents. Thermal activation of feldspar was carried out at temperatures of 500–700 ◦C using muffle furnace. The BET results of the thermal activation revealed that feldspar activated at 600 ◦C has the highest surface area and pore volume of 533.9 m²/g and 0.272 cc/g respectively. The Fourier’s transformed infrared (FT-IR) results indicated that several functional groups were involved in the adsorption process of the phosphate and ammonium ions some of which were O-H, N-H and C-O groups. The results showed that irregular-layered structures of the raw feldspar became smooth and regular after thermal activation. The effects of pH, adsorbent dosage, temperature, contact time and initial PO₄3− and NH₄⁺ concentrations on the adsorption of phosphate ions and ammonium ions were investigated using atomic adsorption spectroscopy (ASS). The adsorption studies of phosphate ion and ammonium ion onto feldspar increased with contact time, adsorbent dosage and temperatures until optimum values were reached.

Development and evaluation of mechanistic model for standard SCR, fast SCR, and NO2 SCR of NH3-SCR over Cu-ZSM-5

Selective catalytic reduction (SCR) systems are an effective way of treating NOx emissions to meet increasingly stringent international emission standards. However, the difference of reaction temperature and catalyst location will restrict the reaction of SCR to some extent. Therefore, considering the different reaction conditions, it is necessary to analyze the relationship between them for the study of SCR reaction. In this paper, Cu-ZSM-5 is selected as the catalyst in the SCR reaction, and the effects of different temperatures and catalyst locations on NH3 molar concentration and NOx conversion under three different SCR are investigated. Firstly, a dynamic model of NH3-SCR is established and verified by the experimental data of fast SCR, standard SCR, and NO2-SCR in steady state. Then, the RSM (Response Surface Methodology) is used to further optimize NOx conversion rate. The optimal reaction conditions under the three SCR reactions were obtained by RSM optimization. The results indicate that both reaction temperature and catalyst location exert significant effects on NOx conversion under the three SCR reactions. Finally, the performance of NH3-SCR over Cu zeolite catalyst is predicted and further evaluated to provide combinations and frameworks for improved performance.

Effect of Sintering Temperature on Microstructure and Properties of PcBN Composites

Effect of Sintering Temperature on Microstructure and Properties of PcBN Composites

The Influence of Annealing on the Compositional and Crystallographic Properties of Sputtered Li–Al–O Thin Films

Li–Al–O materials are interesting for several applications. Herein, a Li–Al–O thin‐film materials library, deposited by inert magnetron sputtering and postdeposition annealing in O2 atmosphere, is used to study the effects of different annealing temperatures (300–850 °C) and durations (1 min to 7 h) on crystallinity and composition of the films. X‐ray photoelectron spectroscopy depth profiling reveals inhomogeneous compositional depth profiles of conventionally annealed films (300–650 °C, 3–7 h) with increased Li contents toward the film surface and increased Al contents toward the film–substrate interface, as confirmed by a combination of Rutherford backscattering spectrometry and deuteron‐induced nuclear reaction analysis. The minimum temperature for the formation of crystalline LiAlO2 in the otherwise amorphous films is 550 °C. The undesired inhomogeneous depth profiles are transformed into homogeneous ones by rapid thermal annealing (750–850 °C, 1–10 min), while simultaneously causing the formation of crystalline LiAlO2. Therefore, rapid thermal annealing is shown to be more suitable than conventional annealing for the thermal processing of Li–Al–O thin films. Moreover, this conclusion is expected to have broader relevance beyond Li–Al–O materials, as it is likely to apply to other Li metal oxides, of which there are many technologically relevant ones.

Low temperature inhibits food intake via TRPA1 channel activation in Nile tilapia (Oreochromis niloticus)

Low temperatures significantly influence feeding behavior in ectothermic vertebrates, but the underlying mechanisms remain elusive. This study investigated the role of transient receptor potential ankyrin 1 (TRPA1) channels in mediating the appetite-suppressing effects of low temperature in Nile tilapia. TRPA1 was found to be highly expressed in the hypothalamus and co-localized with neuropeptide Y (NPY) neurons. Exposure to low temperatures reduced feeding frequency and increased TRPA1 expression. In vitro experiments demonstrated that low temperature and TRPA1 agonists induced calcium influx, which was blocked by a TRPA1 inhibitor. TRPA1 expression exhibited post-prandial increases and was downregulated by fasting. TRPA1 activation dose-dependently inhibited food intake, while its inhibition restored feeding suppressed by low temperature. TRPA1 activation downregulated orexigenic factors and upregulated anorexigenic factors through Ca2+/calmodulin-dependent pathways. These findings suggest that TRPA1 plays a crucial role in sensing low temperatures and regulating feeding behavior in tilapia.

Study on the phase state and temperature-pressure distribution of CO2 injection wellbore and its effect on tubing stress conditions

This study investigates the phenomena observed during CO₂ injection processing in wellbores, particularly the annular pressure buildup typically attributed to inadequate packer sealing. We propose that temperature, pressure, and phase changes during CO₂ injection induce equivalent stresses, leading to packer unsealing. A detailed CO₂ injection model was developed, incorporating temperature-pressure coupling and phase transitions using the state equation. The model evaluates the effects of injection temperature, pressure, and volume on CO₂ density, temperature, pressure, phase state, and velocity, and calculates the stress on the tubing at various depths. Validation against actual measurements showed errors of 1.43% for pressure and 0.66% for temperature, confirming the model's accuracy. Key findings reveal that injection temperature significantly affects CO₂ phase changes, while injection temperature and volume respectively impact stress at the wellhead and bottom. The model provides a robust tool for optimizing CO₂-EOR processes, confirming that changes in injection parameters can indeed cause packer unsealing, and its reliance on precise input data highlights the need for accurate field measurements.

Magnetic pomegranate peels activated carbon (MG-PPAC) composite for Acid Orange 7 dye removal from wastewater

A magnetic pomegranate peels activated carbon (MG-PPAC) nanocomposite (23.46–26.75 nm) was prepared as an effective adsorbent for Acid Orange 7 (AO7) dye removal from wastewater. The effects of impregnation ratio and activation temperatures (600–900 °C) on the specific surface area and pore morphology were studied. BET, SEM, EDX, FT-IR, XRD and VSM are considered the synthesized composite MG-PPAC. The prepared magnetic composite at 700 °C activation temperature and impregnation ratio 1/2 (peels/ZnCl2) exhibited 513.34 m2/g surface area, 0.4025 cm3/g volume of the total pores, and 3.1364 nm mean diameter of the pores. The magnetization saturation, remanence and coercivity of the MG-PPA composite were 14.116 emu/g, 0.50685 emu/g, and 19.705 G, respectively. Also, the composite MG-PPAC was in a super-paramagnetic state at room temperature and could be gathered within 5 S (less than 5 S) with an external magnetic field. The impact of pH, adsorbent dose, initial concentration of adsorbate (AO7 dye), and time of contact have been studied to optimize the removal process. Langmuir, Freundlich and Temkin isotherm models were used to investigate MG-PPAC adsorption behavior for AO7 dye. Applicability of the Langmuir isotherm model demonstrates a monolayer adsorption AO7 dye removal process, and the maximum monolayer capacity (Qm) attained from linear solvation of LIM is 322.58 mg/g. Furthermore, the highest removal was 99.53% at pH 2.25. Also, the adsorption process was tested using like pseudo-first-order, pseudo-second-order, intraparticle diffusion, film diffusion, and Elovich models. The pseudo-second-order model is well-fitted to the operational data of AO7 dye removal.

Extraction of pre-earthquake anomalies from borehole strain data using Graph WaveNet: a case study of the 2013 Lushan earthquake in China

Abstract. On 20 April 2013, Lushan experienced an earthquake with a magnitude of 7.0. In seismic assessments, borehole strainmeters, recognized for their remarkable sensitivity and inherent reliability in tracking crustal deformation, are extensively employed. However, traditional data-processing methods encounter challenges when handling massive dataset-s. This study proposes using a Graph WaveNet graph neural network to analyze borehole strain data from multiple stations near the earthquake epicenter and establishes a node graph structure using data from four stations near the Lushan epicenter, covering the years 2010–2013. After excluding the potential effects of pressure, temperature, and rainfall, we statistically analyzed the pre-earthquake anomalies. Focusing on the Guza, Xiaomiao, and Luzhou stations, which are the closest to the epicenter, the fitting results revealed two acceleration events of anomalous accumulation that occurred before the earthquake. Occurring approximately 4 months before the earthquake event, the first acceleration event indicated the pre-release of energy from a weak fault section. Conversely, the acceleration event observed a few days before the earthquake indicated a strong fault section that reached an unstable state with accumulating strain. We tentatively infer that these two anomalous cumulative accelerations may be related to the preparation phase for a large earthquake. This study highlights the considerable potential of graph neural networks in conducting multistation studies of pre-earthquake anomalies.

Optimization of Extraction Conditions from Gac Fruit and Utilization of Peel-Derived Biochar for Crystal Violet Dye Removal.

Gac fruit (Momordica cochinchinensis Spreng.) is a prominent source of carotenoids, renowned for its exceptional concentration of these compounds. This study focuses on optimizing the extraction of active components from the aril of gac fruit by evaluating the effects of extraction temperature, solid-liquid ratio, and extraction time. The primary objective is to maximize the yield of gac oil while assessing its antioxidant capacity. To analyze the kinetics of the solid-liquid extraction process, both first-order and second-order kinetic models were employed, with the second-order model providing the best fit for the experimental data. In addition, the potential of gac fruit peel as a precursor for biochar production was investigated through carbonization. The resultant biochars were evaluated for their efficacy in adsorbing crystal violet (CV) dye from aqueous solutions. The adsorption efficiency of the biochars was found to be dependent on the carbonization temperature, with the highest efficiency observed for BCMC550 (91.72%), followed by BCM450 (81.35%), BCMC350 (78.35%), and BCMC250 (54.43%). The adsorption isotherm data conformed well to the Langmuir isotherm model, indicating monolayer adsorption behavior. Moreover, the adsorption kinetics were best described by the pseudo-second-order model. These findings underscore the potential of gac fruit and its byproducts for diverse industrial and environmental applications, highlighting the dual benefits of optimizing gac oil extraction and utilizing the peel for effective dye removal.

Characterization of aqueous foams of alkyl polyglycoside, GreenZyme, alpha-olefin sulfonate, and cetyltrimethylammonium bromide in the presence of divalent ions

In this study, the impacts of divalent ions (calcium and magnesium) on aqueous foam stability and its rheological properties are investigated. A biodegradable surfactant of alkyl polyglycoside, (APG) and a commercial enzyme (GreenZyme, GZ) are used and their performance were compared with synthetic surfactants of alpha-olefin sulfonate (AOS) and cetyltrimethylammonium bromide (CTAB). The findings of the study revealed that the stability of all foams decreased with increasing concentrations of divalent ions, GZ recorded the lowest foam stability in the presence of the two ions and precipitation occurred in the AOS solution. On the other hand, foams generated by APG achieved the highest stability and the foams generated by CTAB showed the second highest stability among the foaming agents. Through rheological analyses, APG and CTAB exhibited shear thinning behaviour and their behaviour were modelled using a power law model in which the model can incorporate the effects of temperature and salinity.

Tribological behavior of graphene/h-BN vdW heterostructures: the role of defects at the BN layer

Molecular dynamics simulations and first principles calculations were performed to study the tribological behavior of graphene/h-BN (G/h-BN) heterostructures with vacancy and Stone–Wales (SW) defect under uniform normal load, revealing the mechanism of the effect of defect types on friction, and discussing the coupling effect of temperature and interfacial defects on the tribological behavior of G/h-BN heterostructures. Under the normal force of 0.2 nN/atom, the friction force of the four systems is 0.0057, 0.0096, 0.0077, and 0.26 nN, respectively. The friction force of SW defect heterostructure is 45 times that of perfect interface heterostructure. The influence of defect type on friction force is SW > SV > DV. By observing the dynamic change of the Z-direction coordinate position of the sliding layer atoms, the slip potential energy curves and the evolution law of the moiré pattern, the relationship between the structural morphology and the energy change of different defective heterostructures and the frictional behavior was investigated comprehensively and intuitively for the first time. From the perspective of atomic strain, the deformation of heterostructures at the atomic level was quantified. The results showed that at 300 K and 0 K, the maximum strain of atoms in the sliding layer was 11.25% and 9.85%, respectively. The thermal perturbation mainly occurs in the out-of-plane direction, which in turn affects the friction. Through density functional theory, it is found that under uniform load, it is difficult to form bonds between the graphene sliding layer and the substrate layer when the defects are in the h-BN substrate layer, which has less influence on the friction of the system, thus making the defective heterostructures also remainsuperlubricity state. These results provide a new understanding of the interfacial friction of G/h-BN defective heterostructure.