Temperature-dependent Drift Research Articles

Reduction in Temperature-Dependent Fiber-Optic Gyroscope Bias Drift by Using Multifunctional Integrated Optical Chip Fabricated on Pre-Annealed LiNbO3

The refractive index change obtained after annealed proton exchange (APE) in lithium niobate (LiNbO3) crystals depends on both the proton exchange process carried out in hot acid and the structure of the crystals. In devices produced by the APE method, dislocations and lattice defects within the crystal structure are considered to be primary contributors to refractive index discontinuities and waveguide instability. In this study, the effects of pre-annealing LiNbO3 crystals at 500 °C on multifunctional integrated optical chips (MIOCs) were investigated through interferometric fiber-optic gyroscope (IFOG) system-level tests. It was observed that the pre-annealing process resulted in an improvement in the optical throughput of MIOCs (from %34 to %51) and the temperature-dependent bias drift stability of the IFOG (from 0.031–0.038°/h to 0.012–0.019°/h). The angle random walk (ARW) was measured as 0.0056 deg/√h.

Localized Shims Enable Low-Field Simultaneous Multinuclear NMR Spectroscopy.

This Article introduces a smart localized shimset, integrated with a radiofrequency (RF) microsolenoid and optimized as a single unit to locally achieve high-resolution NMR spectroscopy, as a significant advancement toward achieving parallel NMR spectroscopy. The shimset, consisting exclusively of linear shims, demonstrates the capability to improve NMR line width from 84 to 4 Hz in a 1.05 T preclinical MRI scanner. This enhancement enables the resolution of j-couplings in the sample while requiring a total power of 545 mW. Furthermore, a novel method is presented for concurrently obtaining multinuclear NMR spectra using a single RF channel. This approach allows for the utilization of high-sensitivity NMR signals as a reference to correct field drift, facilitating signal averaging in a permanent magnet NMR scanner that is prone to significant temperature-dependent drift.

Three robust temperature-drift compensation strategies for a MEMS gravimeter

Gravimeters fabricated with MEMS suffer from temperature-dependent drifts in their long-term stability. We analyze the thermal contributions to the signal, and we propose three mechanisms to mitigate their effects. The first one uses materials that fulfill the condition αE=−2α, where thermal expansion is canceled by the temperature variation of Young’s modulus. The second one uses the thermal expansion to introduce a compression that compensates variation in the force of the spring. In the third one, expansion compensates the displacement of the proof mass in the sensor, rather than the force. The three mechanisms are robust since they only depend on the temperature of the sensor itself.

Design, Development, and Performance Evaluation of GMR-Based Current Sensor for Industrial and Aerospace Applications

The article presents the development of an open-loop current sensor using indigenous multilayered giant magnetoresistance (GMR-ML) technology. The proposed current sensor consists of a magnetic core with an air gap, a GMR sensor chip, and a bias magnet. A GMR chip is biased with a permanent magnet to obtain linear bipolar output characteristics. The GMR chip measures the magnetic field produced in the air gap as a result of the current flowing through a conductor. The sensor design and characteristics were optimized and verified using both simulation and experiments. Several prototypes were fabricated and tested for the current range of ± 25 A. Experimental results indicate the sensitivity of the order of 0.165 mV/V/A with the temperature dependence of the sensitivity – 0.28 %/°C and bandwidth of 100 kHz. The fabricated prototypes were further compensated for temperature-dependent drift in sensitivity and offset in the temperature range of – 25 °C to 85 °C. The compensated sensor exhibits a sensitivity of 80 ± 0.5 mV/A with the temperature dependence of the sensitivity of 0.005 %/°C. The change in offset voltage of compensated sensor was less than 10 mV across the temperature range. The compensated prototype sensor shows a total output error of less than 1 % over the operating temperature range. Further, the performance of the sensor was evaluated for aerospace applications and compared with the existing current sensor. The comparative data shows an equivalent performance during the test.

Microstructural analysis, magnetic interactions, and electrical transport studies of [formula omitted] nanoparticles

This study focuses on the synthesis, structural characterization, magnetic interactions, and electrical transport properties of copper-doped zinc ferrite (Zn1−xCuxFe2O4) nanoparticles with varying Cu concentrations (x = 0.00, 0.03, 0.06, 0.10) using the co-precipitation method. The structural and morphological properties were analyzed using X-ray diffraction (XRD) and scanning electron microscopy (SEM), through TEM, while the BET technique was employed to determine the surface area, pore size, and specific surface area. The synthesized nanoparticles were found to exhibit a cubic spinel structure with lattice parameters decreasing as Cu content increased. The photoluminescence spectra indicated emission energies and wavelengths in the green region of the visible spectrum. The magnetic properties were studied using a vibrating sample magnetometer (VSM), revealing that Cu+2 doping resulted in the highest saturation magnetization (16.47 emu/g) by using an applied up to 50 kOe. The electrical properties were studied in the frequency range from 25 Hz to 2 MHz as a function of temperature ranging from 300 K to 480 K with an increment of 20 K. The electrical conductivity of the nanoparticles was found to increase with temperature and Cu content which is attributed to the thermally activated mechanism and predominantly dominated by overlapping large polaron tunneling (OLPT). The activation energy obtained from DC conductivities decreased order 0.63–0.48 eV for the synthesized nanoparticles. The temperature-dependent drift mobility exhibited p-type semiconducting behavior. Overall, the results suggest that Zn1−xCuxFe2O4 NPs have the potential for use in various applications, including sensors, energy storage, and catalysis.

Model-Based Correction of Temperature-Dependent Measurement Errors in Frequency Domain Electromagnetic Induction (FDEMI) Systems.

Data measured using electromagnetic induction (EMI) systems are known to be susceptible to measurement influences associated with time-varying external ambient factors. Temperature variation is one of the most prominent factors causing drift in EMI data, leading to non-reproducible measurement results. Typical approaches to mitigate drift effects in EMI instruments rely on a temperature drift calibration, where the instrument is heated up to specific temperatures in a controlled environment and the observed drift is determined to derive a static thermal apparent electrical conductivity (ECa) drift correction. In this study, a novel correction method is presented that models the dynamic characteristics of drift using a low-pass filter (LPF) and uses it for correction. The method is developed and tested using a customized EMI device with an intercoil spacing of 1.2 m, optimized for low drift and equipped with ten temperature sensors that simultaneously measure the internal ambient temperature across the device. The device is used to perform outdoor calibration measurements over a period of 16 days for a wide range of temperatures. The measured temperature-dependent ECa drift of the system without corrections is approximately 2.27 mSm−1K−1, with a standard deviation (std) of only 30 μSm−1K−1 for a temperature variation of around 30 K. The use of the novel correction method reduces the overall root mean square error (RMSE) for all datasets from 15.7 mSm−1 to a value of only 0.48 mSm−1. In comparison, a method using a purely static characterization of drift could only reduce the error to an RMSE of 1.97 mSm−1. The results show that modeling the dynamic thermal characteristics of the drift helps to improve the accuracy by a factor of four compared to a purely static characterization. It is concluded that the modeling of the dynamic thermal characteristics of EMI systems is relevant for improved drift correction.

Uncertainty Analysis of Scattering Parameters Calibrated by an Electronic Calibration Unit Based on a Residual Model

We propose a new residual model to analyze the uncertainty of scattering parameters (S-parameters) calibrated by an electronic calibration unit (ECU). Residual errors are usually estimated from the observed ripple after connecting a load or a short at the end of an airline. Therefore, this ripple method can only be used in a frequency range where the airline loss was not large. We, however, obtained the residual error from the uncertainty of the calibration kit using a simple numerical approach. As a result, we can determine the correlations between real/imaginary and magnitude/phase uncertainties. The proposed residual model showed the same results as a VNA error model. We also added a new error term to account for the effect of temperature-dependent drift of the ECU. In addition, we analytically derived the sensitivity coefficients for a 2-port DUT based on the proposed residual model. The proposed residual model will be helpful for the uncertainty analysis of S-parameters calibrated using the ECU.

Twin-CQCM and Twin-TQCM Sensors With Wide Operating Temperature Range for Outgassing and Atomic Oxygen Measurement

In this paper, we propose a new Quartz Crystal Microbalance (QCM) sensor with temperature control, which can assess outgassing properties during spacecraft development. It will be referred to as the “Twin-QCM sensor”. There are two types. The Twin-Cryogenic QCM (Twin-CQCM) sensor is warmed by a built-in heater with an operating temperature of -190 to +125°C, and the Twin-ThermoelectricQCM (Twin-TQCM) sensor is warmed and cooled by a built-in Peltier module that can control the temperature within -80 to +125°C. Using a temperature compensation technique, the temperature-dependent drift of the frequency was found to be less than ±10 ppm over all operating temperatures. An RTD temperature sensor was mounted on the quartz crystal to improve the accuracy of temperature measurement. To confirm the accuracy, an additional temperature sensor installed at the center of the crystal. The sensor output temperature value was compared to that of the additional sensor, with the difference between both temperature sensors being +0.4 to +2.6°C in the temperature range from -130 to +100°C. Through the measurement of the sensor's dynamic range, it was found that the deposited contaminant film in a vacuum increasingly changed such physical properties as viscoelasticity as the temperature increases.

Wind load estimation on an open-grown European oak tree

Abstract In this study, we investigate the relationship between the mean wind-induced load on an open-grown oak tree and the mean wind speed. The estimation of the wind load is based on bending moment observations on the stem, using strain gauges installed close to the base of the tree. The measurement campaign included periods where the crown was both with and without foliage. A new post-processing method to compensate for time- and temperature-dependent drifts of long-term strain gauge measurements is presented. The time-scale, at which the method is applied, is determined from the observed high coherence between the wind speed and the induced bending moments. The analysis shows that the wind load on the tree is proportional to the wind speed raised to an exponent of 1.60–1.68 and 1.90–2.01 in the case of a crown with and without leaves, respectively. The results indicate that the presence of foliage increases the wind-induced load by a factor of 2–3. The impact of the wind speed range on these results is discussed and compared to the measured wind deficit in the lee of the tree. The application of this method can potentially be extended to other tree mounted sensors.

The spectral mode evolution in a blue InGaN laser diode

The mode evolution of an InGaN blue laser diode with operating current and diode temperature was investigated. The spectra of a 445-nm InGaN blue laser diode with operating currents and diode temperatures was recorded using an ultrahigh resolution spectrometer and a scanning Fabry-Perot interferometer. The blue laser diode can deliver a mW-level single frequency beam with about 20 MHz linewidth at nearly above the lasing threshold. And the temperature-dependent wavelength drift was estimated as 0.31 nm for single longitudinal mode operation region. The spectra showed the number of the longitudinal modes increased with raising operating current. Analysis of the mode evolution of a blue laser diode with operating current and diode temperature is important when how to choose the laser diode for specific applications.

Impact of Blackbody Warm-Up Cool-Down Cycle on the Calibration of Aqua MODIS and S-NPP VIIRS Thermal Emissive Bands

This paper evaluates the calibration quality during the blackbody (BB) warm-up cool-down cycle for thermal emissive bands onboard Aqua Moderate Resolution Imaging Spectroradiometer (MODIS) and Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS). This evaluation utilizes data from Aqua MODIS Collection 6 Level-1B products and VIIRS Sensor Data Records in 6-min granule format provided by the NASA Land Science Investigator-led Processing System. Nearly simultaneous hyperspectral measurements from the Aqua Atmospheric Infrared Sounder (AIRS) and the S-NPP Cross-track Infrared Sounder (CrIS) are used as references for MODIS and VIIRS, respectively. Each AIRS footprint of 13.5 km is co-located with multiple MODIS pixels while each CrIS field of view of 14 km is co-located with multiple VIIRS pixels. The corresponding AIRS-simulated MODIS and CrIS-simulated VIIRS radiances are derived by convolutions based on sensor-dependent relative spectral response functions. In this paper, the analysis mainly focuses on the bands that are used in sea surface temperature products. The results show that there is virtually no impact for MODIS bands 22 and 23 and bands 31 and 32 for a BB temperature below 290 K; however, when the BB temperature increases above 290 K, the impact is up to 0.3 K for bands 22 and 23 and 0.05 K for bands 31 and 32, respectively. For VIIRS, BB temperature-dependent drifts are observed in M15 and M16, which can reach 0.15 and 0.1 K, respectively, over the operational BB temperature range and the VIIRS brightness temperature range.

Investigation into the formation of double layers caused by temperature dependent drifts in the ambit of classical distributions of inertial electrons and ions in space plasma

The determination of double layers (DLs) of specific amplitudes corresponding to a known amount of drifts v0 is completely a new result in this investigation. The same value of c(=v0 −M kz) with temperature dependent drifts v0 for different α (temperature), M (Mach number), and kz (direction) values is seen to produce double layers (DLs) of the same amplitudes positive or negative. Two new classical distributions of non-thermal inertial electrons and ions are established.

A 0.8 V Supply- and Temperature-Insensitive Capacitance-to-Digital Converter in 0.18-<inline-formula> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math> </inline-formula> CMOS

A low-voltage, low-power, capacitance-to-digital converter (CDC) that is insensitive to supply and temperature variations is presented in this paper. The CDC comprises two matched $RC$ oscillators and a counter-based programmable digital converter. The transfer function of the proposed CDC is a scaled ratio of the capacitors having equal drift coefficients, making it insensitive to supply as well as temperature variations. Worst case temperature-dependent drift of ±153.4 ppm/°C is measured between −40 and +120 °C while worst case supply-dependent drift of ±1.12% is measured between 0.8 and 1.2 V over full-scale capacitance range. The proposed CDC achieves 2.05 fF resolution, consuming $23~\mu \text{A}$ from a 0.8 V supply, at a full-scale range of 3.36 pF. The CDC, realized in 0.18- $\mu \text{m}$ CMOS process, has an active area of 0.102 mm2 and offers a scalable resolution within a range of 2–13 b.

Mechanisms of temperature- and field-dependent effective drift mobilities and impact ionization coefficients in amorphous selenium

The mechanisms of electric-field- and temperature-dependent effective drift mobility and impact ionization coefficient of both holes and electrons in amorphous selenium (a-Se) are investigated in this paper. An analytical model for the microscopic mobility, momentum relaxation mean free path, and hence the effective drift mobility and impact ionization coefficient of carriers, is proposed in this paper by considering the density of states distribution, field enhancement release rate from the shallow traps, and carrier heating. The results of the model are fitted with the published experimental results on effective mobility and impact ionization coefficient with wide variations of the applied electric field and temperature. A better fitting considering thermally activated tunneling for the field-enhancement release rate indicates that the effective drift mobility at extremely high fields is mainly controlled by the neutral defect states near the band edges. The density of state function near the band edges, consisting of an exponential tail and a Gaussian peak, can successfully describe the electric-field- and temperature-dependent effective drift mobility characteristics in a-Se. The momentum relaxation mean free path decreases with increasing field and decreasing temperature, which is required to describe the electric-field- and temperature-dependent behaviors of impact ionization coefficient in a-Se.

Reducing polarization-fluctuation induced drift in resonant fiber optic gyro by using single-polarization fiber

A novel hybrid single-polarization (SP) fiber ring resonator is demonstrated by using a polarization-maintaining coupler formed by splicing a section of SP fiber into the resonator. The SP fiber selectively eliminates the unwanted resonance by introducing high loss for the unwanted eigenstates of polarization in the resonator. The calculated result shows that this hybrid SP resonator is a good candidate for a tactical-grade performance gyro with a high environmental temperature stability. The experiment shows that the desired resonance in the resonator can keep an excellent stability in a wide temperature range, thus the temperature-dependent polarization-fluctuation drift in the resonant fiber optic gyro is sufficiently suppressed. As a result, a random walk coefficient of 0.08°/√h and a typical bias stability below 0.3°/h for an integration time of 300 s have been carried out.

Passive Temperature Stabilization of Silicon Photonic Devices Using Liquid Crystals.

In this work we explore the negative thermo-optic properties of liquid crystal claddings for passive temperature stabilization of silicon photonic integrated circuits. Photonic circuits are playing an increasing role in communications and computing, but they suffer from temperature dependent performance variation. Most existing techniques aimed at compensation of thermal effects rely on power hungry Joule heating. We show that integrating a liquid crystal cladding helps to minimize the effects of a temperature dependent drift. The advantage of liquid crystals lies in their high negative thermo-optic coefficients in addition to low absorption at the infrared wavelengths.

2-DOF vibratory gyroscope fabricated by SU-8 based UV-LIGA process

This paper reports fabrication of 2-DOF vibratory gyroscope using SU-8 based UV-LIGA process. The device structure is designed to be symmetrical in order to match the resonance frequencies of drive and sense mode oscillators and also to minimize their relative temperature dependent drift. The overall arrangement is such that the two vibration modes do not affect each other and therefore, mechanical decoupling is achieved which helps in minimizing bias drift. The design is optimized to be compatible with the UV-LIGA process having 10 μm thick electroformed nickel as structural layer. Photolithography to create 11 μm thick SU-8 molds for electroforming sacrificial copper and structural nickel layer is optimized using multiple exposure technique that ensures near vertical side walls. Since the highly cross-linked SU-8 remaining after development is difficult to remove reliably from high aspect ratio structures without damage or alteration to the electroformed metals, a 2.45 GHz MW plasma etching process is developed with CF4/O2 mixes. The fabricated device is checked for off-plane misalignment between the stationary and movable comb fingers using white light interferometry and it is found to be almost negligible. Also, the prototype device is characterized for amplitude and phase spectral responses using Polytec MSA-500 Micro System Analyzer. The drive and sense mode resonance frequencies are observed at 7.3 and 7.1 kHz respectively against the mode matched designed frequency of 7.5 kHz.

A simple and inexpensive system for controlling body temperature in small animal experiments using MRI and the effect of body temperature on the hepatic kinetics of Gd-EOB-DTPA

The purpose of this study was to develop a simple and inexpensive system for controlling body temperature in small animal experiments using magnetic resonance imaging (MRI) and to investigate the effect of body temperature on the kinetic behavior of gadolinium ethoxybenzyl diethylenetriamine pentaacetic acid (Gd-EOB-DTPA) in the liver.In our temperature-control system, body temperature was controlled using a feedback-regulated heated or cooled air flow generated by two Futon dryers. The switches of the two Futon dryers were controlled using a digital temperature controller, in which the rectal temperature of a mouse measured by an optical fiber thermometer was used as the input.In experimental studies, male ICR mice aged 8weeks old were used and allocated into 5 groups (39-, 36-, 33-, 30-, and 27-degree groups, n=10), in which the body temperature was maintained at 39 °C, 36 °C, 33 °C, 30 °C, and 27 °C, respectively, using our system. The dynamic contrast-enhanced MRI (DCE-MRI) data were acquired with an MRI system for animal experiments equipped with a 1.5-Tesla permanent magnet, for approximately 43min, after the injection of Gd-EOB-DTPA into the tail vein. After correction of the image shift due to the temperature-dependent drift of the Larmor frequency using the gradient-based image registration method with robust estimation of displacement parameters, the kinetic behavior of Gd-EOB-DTPA was analyzed using an empirical mathematical model. With the use of this approach, the upper limit of the relative enhancement (A), the rates of contrast uptake (α) and washout (β), the parameter related to the slope of early uptake (q), the area under the curve (AUC), the maximum relative enhancement (REmax), the time to REmax (Tmax), and the elimination half-life of the contrast agent (T1/2) were calculated.The body temperature of mice could be controlled well by use of our system. Although there were no significant differences in α, AUC, and q among groups, there were significant differences in A, REmax, β, Tmax, and T1/2, indicating that body temperature significantly affects the kinetic behavior of Gd-EOB-DTPA in the liver.In conclusion, our system will be useful for controlling body temperature in small animal experiments using MRI. Because body temperature significantly affects the kinetic behavior of Gd-EOB-DTPA in the liver, the control of body temperature is essential and should be carefully considered when performing DCE-MRI studies in small animal experiments.

Reduction of polarization-fluctuation induced drift in resonator fiber optic gyro by a resonator integrating in-line polarizers

A method to decrease the polarization-fluctuation induced drift in a resonator fiber optic gyro (R-FOG) is demonstrated by inserting two in-line polarizers in a polarization-maintaining fiber resonator with twin 90° polarization-axis rotated splices. The in-line polarizers attenuate the unwanted resonance by introducing high loss for the unwanted eigenstates of polarization in the resonator. Compared to the resonator without in-line polarizers, the polarization-fluctuation induced drift is reduced by 6×10(3) times. The desired resonance in the resonator can keep excellent stability in a wide temperature range; thus the temperature-dependent polarization-fluctuation drift in the R-FOG is sufficiently suppressed. A typical bias stability of 4.7°/h over 6500 s with an integration time of 10 s has been carried out. To the best of our knowledge, the long-term bias stability and high temperature stability are the best ever demonstrated in an R-FOG.

Novel Stable and Reliable Readout Electronics for HTS rf SQUID

Conventional readout electronics for radio-frequency SQUIDs exhibit long-term instabilities due to a temperature-dependent frequency drift of their voltage controlled oscillator. A novel electronics with a quartz-controlled synthesizer was developed to solve this problem. The frequency can be adjusted from 450 to 900 MHz with 2 ppm frequency stability, the amplitude range covers more than 60 dB. An adjustable phase shifter for demodulation is implemented to compensate for variable cable length. The total amplification is about 100 dB. The electronics with touchpanel and remote USB control is commercially available with up to three preamplifier units. Because thermal drift is eliminated, it is well suited for outdoor applications, e.g. in geophysics.