Treatment Technologies Research Articles

Cotton Gin By-Products Utilization: Past, Present, and Future

The regional concentration of cotton gin by-products (CGB) has increased significantly over the past three decades because of the consolidation of smaller gins into larger gins. Although several studies have investigated the potential of various waste treatment/valorization technologies to improve the management of CGB, most of the technologies' economic feasibility remains a challenge. Therefore, there is a need to review the existing and emerging technologies vis-à-vis process economics and changes in the cotton ginning industry. This study reviews the published status of these existing technologies (in terms of the challenges and potentials), analyzes the prospects of some emerging waste treatment technologies for CGB, and discusses future economic and environmental sustainability directions. Where appropriate, new information from studies conducted in the U.S. and Australia is provided to support existing published data. The results show that the main limiting factors include production costs (e.g., energy and feedstock/additives costs) and logistics/supply. Additionally, the results support a solid potential for the sustainable use of CGB for various applications. However, the potential can be achieved by optimizing specific treatment processes, combining multiple processes through hybrid or integrated systems, co-treating CGB with other affordable and readily available materials (such as by-products from other agricultural operations), and improving return on investment for products developed.

Adsorptive potential of apricot (Prunus Armeniaca) stone in the removal of Cr (VI) and Fe (II) ions from Aquatic Systems: Kinetic and isothermal investigations

Biogenic adsorbents have emerged as a promising alternative to the traditional remediation techniques of heavy-metals contaminated water treatment. Using apricot (Prunus Armeniaca) stone as a naturally derived adsorbent, the current study provides a comprehensive analysis of the kinetic and isothermal characteristics associated with Cr (VI) and Fe (II) ion adsorption. The results show that 0.5 mg of the adsorbent removed approximately 90 % of Cr (VI) and Fe (II) ions from 100 ppm solutions within 120 min at 298 K at 300 rpm stirring speed. Equilibrium was attained within 90 to 120 min, with a significant increase in the removal percentage observed in the first 30–40 min for both metals compared to the subsequent 80–90 min. The optimal pH conditions for adsorption were determined to be acidic (pH = 1.5) for Cr (VI) and neutral (pH = 7) for Fe (II). The adsorption kinetics followed a pseudo-second order model, while the isothermal equilibrium data best fit the Freundlich model over the Langmuir model. Moreover, the thermodynamic parameters, including ΔG°, ΔH°, and ΔS°, indicated that the sorption process is spontaneous, feasible, and endothermic. The response surface methodology (RSM) analysis showed a high level of accuracy in predicting the percent removal. These findings illustrate the effectiveness of apricot stone as a low-cost and environmentally conscious adsorbent, contributing to the development of sustainable water treatment technologies.

Novel hybrid treatment for canal water recycling by integrating coagulation, catalytic ozonation, and filtration for agricultural sustainability

This study employed a novel approach, utilizing recycled alumina flocs after coagulation/flocculation (C/F) as a catalyst in catalytic ozonation (CO), along with the auxiliary catalyst sodium zeolite (Na-Z), where alumina produces hydroxyl radicals, and zeolite enhances molecular ozone reactions. This synergistic strategy focuses on treating contaminated canal water, recognizing that the presence of various pollutants can reduce the efficacy of a singular catalyst type. In the current investigation, alum, Na-Z, and rice husk (RH) were applied as a coagulant, catalyst, and filter media in C/F, CO, and filtration processes respectively. Four treatment technologies (C/F, O3, O3/Na-Z, and RHF) were studied independently and in four different combinations (O3–C/F, C/F–O3, C/F–O3/Na-Z, and C/F–O3/Na-Z–RHF) for the first time and their efficacious performance was evaluated. It was revealed that the combination-IV (C/F–O3/Na-Z–RHF) was a more efficient and economical treatment than others. This novel integrated treatment C/F–O3/Na-Z–RHF has remarkable removal efficiency of 99 %, 99 %, 85 %, 93 %, 100 %, 89 %, and 93 % for TSS, turbidity, COD, BOD5, fecal coliforms, cadmium, and copper respectively, under optimized working conditions. Also, treated canal water complied with the studied irrigation water quality guidelines. Notably, this efficient treatment combination halved the treatment time compared to others, potentially reducing the electrical energy demand of 11.45 kWh.m−3 and the overall operational treatment cost of 1.62 USD.m−3. Hence, the application of this efficient hybrid treatment system contributed to recycling canal water for agricultural use, livestock, and pasture watering, playing a crucial role in mitigating the water crisis.

Research Progress of Printing and Dyeing Wastewater Treatment

In the textile industry, printing and dyeing technology, as an essential technical basis, produces a lot of printing and dyeing wastewater (PDW) that jeopardizes the ecological environment and human health. PDW generally has the characteristics of large discharge, high chromaticity, strong toxicity, strong alkalinity, complex componentization, poor biodegradability, large fluctuations in water quality and quality, and high content of organic pollutants, belonging to the type of industrial wastewater that is difficult to manage. In this paper, the current research progress of PDW treatment technology from the aspects of physical technology, chemical technology, and biological technology are reviewed. In addition, measures to reduce the damage caused by printing and dyeing wastewater from three perspectives: treatment principle, processes, advantages, and disadvantages are discussed, which provides a reference point for the treatment of printing and dyeing wastewater. It is worth noting that the article reviews the ABS system, which is gaining attention as an emerging technology under biological technology. The purpose of this paper is to provide a reference basis for the selection and application of technology, and then promote the innovation and development of printing and dyeing wastewater treatment technology.

매립지 침출수 처리에서 질산화 공정 최적화 : pH 및 무기탄소원농도가 질소 제거에 미치는 영향

This study was conducted to solve problems that arise in the nitrification of landfill leachate due to the increase in waste generation and diversification of components associated with domestic economic growth. Landfill leachate contains high concentrations of nitrogen compounds and organic substances thus, it is a potential cause of environmental pollution. The study findings confirmed that the nitrification process was inhibited when the metal (Cu) concentration was more than 2.5ppm: further, the nitrification rate could be greatly improved by replenishing alkalinity and adjusting pH. Additionally, appropriate Do and pH alone did not have a sufficient effect on nitrification. This study is expected to contribute to the development of new treatment technology that can minimize the use of chemicals and suppress the generation of secondary toxic substances in the landfill leachate treatment process.

Synergistically enhanced heterogeneous activation of dissolved oxygen for aqueous carbamazepine degradation over S(III) coupled with siderite

The wide occurrence of emerging contaminants (ECs) was drawing more attention due to the potential hazard and threat on human and environment. Carbamazepine (CBZ) is a widely prescribed medication that has garnered considerable research interest with the exposures exceeding the environmental carrying capacity. We have established the innovative heterogeneous advanced oxidation process (AOPs) based on the activated dissolved oxygen (DO) coupled with S(III) and natural iron ore (siderite). In S(III)/O2/siderite system, we investigated the degradation efficiency, reactive species generation mechanism, and degradation pathway of CBZ. CBZ degradation and mineralization rate were 90% above and ∼15% with the reaction time of 40 min. The degradation of CBZ conformed to a pseudo-first-order kinetic model, with an activation energy determination of 76.36 kJ/mol. The optimal initial solution pH was the weak acid condition (pH = 4–6) for CBZ degradation. Moreover, the inhibition effects of coexisting substance including Cl−, HCO3−, and natural organic matter (NOM) on CBZ removal were observed, while the coexisted SO42− exhibited no significant influence. In addition, the reactive species generated in S(III)/O2/siderite system were predominantly identified as sulfate radical (SO4∙-) and hydroxyl radical (∙OH). The crucial intermediate complexes, Fe(III)S(IV)O3(+) and Fe(II)HS(IV)O3(+), was proposed to form in the initial stages of the reaction, which upon decomposition, yielded SO4∙- along with other reactive species. The degradation pathway of CBZ primarily involved deamination, oxidative ring-opening, hydroxylation, decarboxylation, and ketone degradation processes. This work provides the effective approach for the CBZ degradation with the mild reaction conditions and the sustainable technology for ECs treatment and control.

The synergistic mechanism of ultrasonic and heat treatment on the composite structure and mechanical properties of Nb-Si-Zr based in-situ composites

Ultrasonic assisted solidification (UST), heat treatment and alloying are all effective methods to control the microstructure of materials and improve their properties. In this paper, the Nb-16Si-20Zr-2C-xW composites were prepared using ultrasonic assisted solidification technology of high temperature melt (≥1800℃) and heat treatment. The influence mechanism of ultrasonic, the W element, and the synergistic regulation mechanism of ultrasonic and heat treatment on the material were studied. Nb-16Si-20Zr-2C-xW(UST) alloys are mainly composed of Nbss phase and γNb5Si3 phase, and their microstructures are mainly divided into strong active zone(SZ) and weak active zone(WZ). In the Nb-Si superalloy melt treated by ultrasonic wave, the area near the ultrasonic sound source is the strong active zone, while the area far away from the ultrasonic sound source is the weak active zone. The features of faceted primary phases and non-faceted primary phases in the SZ and WZ are explained by the equation of undercooling degree at different interfaces and effect of ultrasonic on component undercooling. As the W element content in the alloys (UST) increases, the content of the Nbss phase increases, the median diameter of the primary γNb5Si3 phase decreases, and the room temperature fracture toughness and compressive strength show an upward trend. When the addition amount of W element reaches 2 at%, there are more crack deflections, crack bridging and secondary cracks in the crack propagation path. Through the special arrangement of primary γNb5Si3 phase in the ultrasonic field, the energy density of ultrasonic waves in the melt is calculate to be 33.5 kW/m2. The microstructure of Nb-16Si-20Zr-2C-xW alloys(UST+HT) became more uniform and spheroidize. It is worth mentioning that there are plenty of long strip γNb5Si3 phases with different orientations in the Nb-16Si-20Zr-2C-0.1W(UST+HT) alloy and the long strip γNb5Si3 phases with the same orientation are arranged in a periodic manner. This special composite structure induces crack deflections and branching cracks when cracks propagation, so the room temperature fracture toughness of Nb-16Si-20Zr-2C-0.1 W (UST+HT) alloy reaches 15.66 MPa·m1/2.

The Role of EM4 (Effective Microorganisms) in Solid Waste-Powered Microbial Fuel Cells: Investigating Voltage Output and Electrical Conductivity For Bioelectricity Generation

The increasing global demand for renewable energy and sustainable waste management solutions has inspired interest in microbial fuel cells (MFCs) as a dual-purpose technology for bioelectricity generation and waste treatment. This study explores the role of EM4, a consortium of effective microorganisms, in enhancing the voltage output and electrical conductivity of solid waste-powered MFCs. A batch system bioreactor assessed the impact of varying organic waste-to-zeolite ratios on MFC performance. The results demonstrated that a 1:1 ratio of organic waste to zeolite produced the highest electrical conductivity (3160 µS/cm) and the most substantial voltage output (777.5 mV) by day three of the experiment. Statistical analysis, including ANOVA and Kruskal-Wallis tests, revealed significant differences in voltage output across treatments, with a positive correlation between electrical conductivity and voltage production. These findings highlight the potential of integrating EM4 and conductive materials like zeolite to optimize bioelectricity generation in MFCs, contributing to the advancement of sustainable energy technologies.

Industrial Pollution in Patna City : Physico-Chemical Analysis of Effluents and Their Effects on Water and Soil

Industrial pollution is a significant concern in Patna City, with rapid urbanization and industrial growth contributing to the degradation of natural resources. This study focuses on the physico-chemical analysis of industrial effluents and their effects on the water and soil quality in and around Patna. Effluents from various industries, including textile, sugar, rice mills, and small-scale manufacturing units, are released into nearby water bodies and soils, posing serious environmental risks. The research aims to assess the levels of pollutants by analysing key physico-chemical parameters such as pH, total dissolved solids (TDS), biochemical oxygen demand (BOD), chemical oxygen demand (COD), heavy metals (lead, chromium, cadmium), and organic contaminants in industrial effluents. Samples were collected from various locations near industrial zones and water bodies. The study also evaluated the impact of these pollutants on soil and groundwater quality. It was found that prolonged exposure to industrial effluents led to the accumulation of toxic metals in soil, reducing its fertility and altering its structure. Additionally, groundwater sources were contaminated with hazardous chemicals, making them unfit for drinking and irrigation purposes. The implementation of advanced treatment technologies and sustainable industrial practices is crucial for safeguarding the environment and public health in Patna City.

Porous polylactide membranes with high piezo-catalytic efficiency for organic wastewater treatment

Piezo-catalysis has been emerged as a green and promising wastewater treatment technology for efficient removal of persistent organic pollutants (POPs), such as 4-nitrophenol (4-NP). However, it remains challenging to achieve advanced materials with combined advantages of high piezo-catalytic efficiency, good hydrophilicity, and environmental friendliness. In this work, highly crystalline porous polylactide (PLA) membranes possessing such exceptional advantages have been successfully prepared from biodegradable poly(L-lactide)/poly(D-lactide)/polyethylene glycol/polyoxyethylene-polyoxypropylene block copolymer (PLLA/PDLA/PEG/PEO-PPO-PEO) blends by melt processing and subsequent water etching. During the melt-processing, the two PLA enantiomers co-crystallize into stereocomplex (SC) crystals and simultaneously the PEG used as a porogen is expelled from the crystalline regions. The results show that the prepared PLA membranes have not only abundant micro-porous structures but also good hydrophilicity due to the preferential localization of PEO-PPO-PEO copolymer on the pore walls, thus giving rise to an extremely high water flux of 2400 L/m2h. More interestingly, the PLA membranes exhibit remarkable piezoelectric activity and the piezo-catalytic degradation efficiency of 4-NP can reach as high as 96 % under the triggering of water flow involved in vacuum filtration. In addition, the membranes show excellent reusability and the high catalytic efficiency can be well-maintained after five repeated uses. These findings suggest broad application prospects of our porous SC-PLA membranes in organic wastewater treatment.

Physicochemical Characterization of Broiler Poultry Litter from Commercial Broiler Poultry Operation in Semiarid Tropics of India

This study characterized the physicochemical properties of broiler poultry litter (BPL) produced from intensively reared commercial broilers that were collected from 110 commercial poultry farms at the end of the production cycle (sixth week). A further 20 samples were collected from the end use point where BPL was utilized as a soil amendment by the farmers after a period of storage for improving poultry litter management practices, developing new litter treatment technologies, or enhancing its use as a sustainable resource. The dry matter (DM), moisture, ash, organic matter (OM), and organic carbon (OC) from the manure samples were 83.04, 16.96, 27.08, 72.92, and 42.39%, respectively. The pH, electrical conductivity (EC) (dS m−1), and Kjeldahl nitrogen (N) were 8.43, 5.74, and 24.2 g kg−1, respectively. The BPL from the cement floor had higher levels of P and K than the mud floor. The correlation studies revealed that the OM, C, N, and Zn had significant positive correlations; pH, moisture, and ash had positive correlations; and EC, DM, and Ca had positive correlations. The EC level of BPL negatively correlated with pH, Fe, and Mn. The N content was found to have a highly significant (p < 0.01) positive correlation with the OM, OC, Ca, and Zn content of BPL, and it was found to have a highly significant (p < 0.01) negative correlation with the ash content, pH, and K content of BPL. The P content of BPL showed a positive correlation (p < 0.01) with the K content and a negative correlation with the Zn (p < 0.05) and Fe (p < 0.01) contents of BPL. Zn was found to be negatively (p < 0.01) correlated with the ash content; the pH; and the K, Fe, and P content of BPL. According to the findings of this study, BPL as such at the end of the production cycle is rich in OM, nitrogen, macrominerals, and microminerals; however, at the point of utility (after a period of storage of 4 to 6 months), there was a loss of OM, N, and mineral concentrations, highlighting the importance of proper storage and composting. Overall, this study on the physicochemical properties of broiler poultry litter is crucial for improving agricultural practices, protecting the environment, and preserving the health and safety of human beings and livestock.

Effective removal of fluoride ions from contaminated water using electrochemical techniques: A critical review on recent developments and environmental perspective

Worldwide, water pollution poses significant threats to human health, with fluoride contamination emerging as a critical hazard. High fluoride concentrations in water cause severe health impacts, including dental and skeletal fluorosis, neurological damage, and harm to the parathyroid gland, cardiovascular, and reproductive systems. Electrochemical technique is one of the most widely used treatment technologies that has been extensively studied and provides a very effective, low-cost method of removing fluoride from contaminated water. The review reports the comprehensive electrochemical strategies for fluoride ions removal. The sources, toxicity, and impacts of fluoride pollution on health are discussed in this review. A comprehensive analysis of current electrochemical methods, including electrolysis, electrocoagulation, and the electro-fenton process, was provided in the context to facilitate the efficient removal of fluoride ions from wastewater. These methods exhibit high removal efficiencies, reaching up to 95 %, and offer scalability and operational flexibility, making them suitable for both centralized and decentralized water treatment systems. Furthermore, the recent advancements in the development of electrochemical technique for fluoride removal are critically reviewed. This study has prospected the recent developments, recommendations and future outlooks on electrochemical technique for fluoride removal.

Design of ternary GO@AgNPs@g-C3N4 membranes for efficient dye removals in integrated photocatalysis-filtration reactors

Photocatalytic composite membranes (PCMs), which integrate the high degradation efficiency of photocatalysts and the physical separation properties of membranes, have emerged as a promising technology for wastewater treatment. Herein, the ternary GO@AgNPs@g-C3N4 PCM was fabricated through a facile vacuum-filtration assembly of graphene oxide (GO), graphitic phase carbon nitride (g-C3N4), and silver nanoparticles (AgNPs) onto commercial mixed cellulose ester (MCE) substrates. The effects of g-C3N4 synthesized from different precursors and various metal nanoparticles on the performance of PCM were systematically investigated. Interestingly, results show the addition of AgNPs not only significantly improves the photocatalytic performance of PCMs but also enhances the mechanical adhesion between the active layer and the MCE substrate. The resultant PCMs exhibit outstanding photocatalytic performance, maintaining dye removal above 89% even after 25 consecutive cycles. Moreover, dye degradation pathways over the PCMs were investigated through free radical scavenging experiments and electron spin resonance characterizations. This simple assembly method results in a 3–12 times increase in flux compared to the layer-by-layer assembly method. Accordingly, our designed PCMs exhibit significant potential for wastewater treatment and water purification applications.

A newly-constructed technology to remove and recover diethyl phthalate from wastewater by using the instant plasticization assembly ability of PVC

Diethyl phthalate (DEP) is a typical environmentally organic pollutant, widely used in the production process of polyvinyl chloride (PVC) to improve the flexibility of plastic materials. Its interaction with living organisms can inflict considerable harm to reproductive system functions. This research aims to utilize tetrahydrofuran (THF) to selectively break the chemical bonds in PVC molecules to provide more adsorption sites. Then incorporates the plasticizing assembly process of PVC to instantly remove and recover DEP from wastewater, achieving waste utilization, and sustainable environmental development. The research found that PTFR with a concentration of around 75 mg/L shows the best DEP removal efficiency. Sequencing batch processing removes more DEP compared to direct processing under the same material usage conditions. Furthermore, the recovery rate of DEP can reach over 90%. The technology demonstrates notable enhancements in removal efficiency and adsorption duration when compared to conventional adsorption techniques. This research has established an instant and efficient method for DEP removal, providing a new idea and technology for plasticizer treatment in practical wastewater.

Research on Coal Mine Environmental Pollution Management and Ecological Restoration Technology

This paper analyses the current situation of environmental pollution in coal mines, its causes, and its impact on the ecological environment, and systematically researches the management of environmental pollution in coal mines and ecological restoration technology. The paper analyses the main categories of coal mine environmental pollution, including water pollution, air pollution, and solid waste pollution, and discusses the causes of these pollution and their destructive effects on the ecological environment. Immediately after that, the article elaborates on the treatment technologies of coal mine environmental pollution, including physical, chemical and biological treatment technologies for water pollution control, blocking, adsorption and covering technologies for air pollution control, and landfill, incineration and resource utilization strategies for solid waste disposal. This paper also discusses coal mine ecological restoration techniques, including species selection and allocation for vegetation restoration, vegetation restoration models, physical, chemical and biological methods for soil improvement, and engineering, vegetation and agricultural measures for soil and water conservation. Through the research of this paper, the researchers aim to provide scientific basis and technical support for the management of coal mine environmental pollution and ecological restoration and to promote the restoration of the ecological environment in mining areas and the sustainable development of the coal industry.

Assessment of electrochemical removal mechanisms of diverse transition metal dichalcogenides for caesium ion removal in wastewater treatment

Abstract Effective treatment of radioactive wastewater is crucial for broader nuclear energy adoption, with caesium radionuclides (most exist in the form of caesium chloride) presenting challenges due to their long half-life and biological hazards. Conventional adsorbents like zeolites and carbon-based materials, including graphene, face limitations in adsorption capacity due to the formation of electric double layers (EDL). This has led to the investigation of alternatives such as transition metal dichalcogenides (TMDs) e.g., MoS2, MoSe2, and WSe2, which offer promising galleries for caesium ion removal. Aside from extensively studied MoS2, there is limited research on the adsorption mechanisms and capacities of other TMDs like MoSe2 and WSe2. Here, we conduct a comparative study examining the removal mechanisms and capacities of exfoliated MoS2, MoSe2, and WSe2 nanosheets, alongside an evaluation of these properties in relation to graphene. Our investigation reveals distinct removal mechanisms and capacities among these three materials for capturing caesium ions in a variety of mechanisms. MoS2 nanosheets primarily utilise a pseudocapacitive charge storage mechanism via intercalation, as evidenced by a total charge storage of 0.78 C g1, with only 2.6% stored via EDL formation. In contrast, MoSe2 predominantly relies on EDL formation, with almost 60% of the total 0.54 C g1 charge storage attributed to this mechanism. Lastly, WSe2 exhibits a combination of both charge storage behaviours, with a total charge storage of 0.77 C g1, of which 14% is due to EDL formation. This research highlights the potential efficacy of TMDs as viable materials for caesium removal, offering an appealing alternative to conventional adsorbents and likely fostering advancements in water treatment technologies.

State-level regulation of disinfection byproducts in the United States

ABSTRACT Disinfection byproducts (DBPs), residual compounds formed from the chemical disinfection of drinking water, can cause a host of damaging public health and environmental impacts. This study evaluates the landscape of regulations designed to reduce the occurrence and/or impact of DBPs, focusing on regulations issued by the US states. Drawing on a systematic search of state administrative codes and agency websites, we first identify the presence, absence, and layering of DBP-related regulations. We then evaluate the number and types of policy tools – the specific approaches required by each regulation, such as monitoring requirements, economic incentives, and required treatment technologies – to identify how DBPs are being managed and how states cluster with relatively more and less robust regulatory frameworks. Finally, we evaluate the relationship between the regulatory approach and the frequency of drinking water quality violations for DBP compounds. While most states have at least one DBP-specific regulation, these vary substantially in their comprehensiveness. The most-used policy tools (monitoring, compliance schedules, and reporting) directly reflect federal regulations; few states have adopted innovative tools such as collaboration or financial incentives. We observe no relationship between regulatory efforts and water quality violations, suggesting that current policy implementation may not adequately address the complex risk of DBPs.

Synthesis and characterization of nickel cobaltite–supported film for hexavalent chromium photocatalytic reduction

ABSTRACT Hexavalent chromium (Cr(VI)) is a prevalent and highly toxic pollutant, posing a serious threat to human health and ecosystems. This study addresses this issue by exploring the photocatalytic reduction of Cr(VI) using hydrothermally synthesized nickel cobaltite (NiCo2O4) spinel–supported films. The research fills the gap for efficient visible light photocatalytic materials for Cr(VI) reduction, with the aim to synthesize, characterize, and assess NiCo2O4-supported films’ photocatalytic activity. Synthesis was achieved via a hydrothermal method on fluorine-doped tin oxide (FTO) and titanium dioxide (TiO2) over FTO substrate. The films were characterized using several techniques and their photocatalytic activity was tested under UV-A and visible light, with Cr(VI) concentration monitored periodically up to 240 min. The NiCo2O4/TiO2 film demonstrated superior photoreduction performance under both UV and visible light radiation compared to TiO2 and NiCo2O4, achieving photoreduction of Cr(VI) by 76% under UV light with a rate constant of 5.79 × 10−3 min−1 and 60% under visible light with a rate constant of 4.74 × 10−3 min−1. In conclusion, hydrothermally synthesized NiCo2O4/TiO2 film shows promising photocatalytic performance for Cr(VI) reduction, marking a significant advancement in photocatalysis and water treatment technologies. Future research will focus on stability assessment, synthesis process optimization, and real-world water treatment application.

Photothermal synergistic catalytic oxidation mechanism of toluene by Ce-doped SrTiO3 via one-pot hydrothermal synthesis

Industrial volatile organic compounds (VOCs) emissions pose significant environmental and human health risks, with photothermal catalysis degradation emerging as a promising VOCs treatment technology. The light response range and catalysis degradation efficiency of photocatalysts, however, need to be improved. This study prepared Ce-doped SrTiO3 perovskite catalysts via a one-pot hydrothermal method. The synergistic photic/thermal degradation mechanism of toluene was uncovered via XPS, Uv–Vis, EPR, and in-situ DRIFTS analysis. It was found that the toluene removal rate and CO2 yield reached their maximums at 200 °C, reaching 95 % and 90 %, respectively, at a Ce doping ratio of 50 %. During the catalytic process, the prerequisite to trigger toluene oxidation, and light promote the generation of reactive oxygen species (·OH and ·O2–), which facilitates the formation of intermediates and thus accelerates the deep oxidation of toluene. The doped Ce increases surface oxygen vacancies while lowering the energy band gap of the catalyst, facilitating the separation of holes and photogenerated electrons. Furthermore, in situ DRIFTS studies demonstrated that toluene undergoes a ring-opening process, producing intermediates such as benzaldehyde and benzoic acid. This study will assist in promoting the use of photothermal synergistic catalytic degradation technology to remove VOCs from industrial sources.

Evaluation and analysis of neurocognitive dysfunction in patients with colorectal cancer after radical resection: A retrospective study.

With the continuous progress of colorectal cancer treatment technology, the survival rate of patients has improved significantly, but the problem of postoperative neurocognitive dysfunction has gradually attracted attention. To analyze the risk factors for delayed postoperative neurocognitive recovery (DNR) after laparoscopic colorectal cancer surgery and constructed a risk prediction model to provide an evidence-based reference for the prevention and treatment of DNR after laparoscopic colorectal cancer surgery. The clinical data of 227 patients with colorectal cancer who underwent laparoscopic surgery and regional cerebral saturation oxygenation (rScO2) monitoring at our hospital from March 2020 to July 2022 were retrospectively analyzed. Common factors and potential factors affecting postoperative DNR were used as analysis variables, and univariate analysis and multifactor analysis were carried out step by step to determine the predictors of the model and construct a risk prediction model. The predictive performance of the model was assessed by the receiver operating characteristic (ROC) curve, the calibration curve was used to assess the fit of the model to the data, and a nomogram was drawn. In addition, 30 patients who met the inclusion and exclusion criteria from January 2023 to July 2023 were selected for external verification of the prediction model. The incidence of postoperative DNR in the modeling group was 15.4% (35/227). Multivariate analysis revealed that age, years of education, diabetes status, and the lowest rScO2 value were the independent influencing factors of postoperative DNR (all P < 0.05). Accordingly, a DNR risk prediction model was constructed after laparoscopic colorectal cancer surgery. The area under the ROC curve of the model was 0.757 (95%CI: 0.676-0.839, P < 0.001), and the Hosmer-Lemeshow test of the calibration curve suggested that the model was well fitted (P = 0.516). The C-index for external validation of the row was 0.617. The DNR risk prediction model associated with rScO2 monitoring can be used for individualized assessment of patients undergoing laparoscopic colorectal cancer surgery and provides a clinical basis for the prevention of DNR after surgery.