Tap Water Research Articles

Development of a highly sensitive ampicillin sensor utilizing functionalized aptamers.

To develop a sensitive and simple ampicillin (AMP) sensor for trace antibiotic residue detection, the influencing factors of the modification effect of nanogold-functionalized nucleic acid sequences (Adenine: A, Thymine: T) were comprehensively analyzed in this study, including the modification method, base length and type. It was found that under the same base concentration, longer chains are more likely to reach saturation than shorter chains; and when the base concentration and length are both the same, A exhibits a higher saturation modification level compared to T. Based on these research findings, a highly sensitive fluorescence aptamer sensor for detecting ampicillin was constructed using the optimized functionalized sequence (ployA6-aptamer) and experimental conditions (6 hours binding time between nucleic acid aptamer and complementary strand, pH 7 working solution, 20 minutes detection time) based on the principle of fluorescence resonance energy transfer. The sensor has a detection range of 0.18 ng ml-1 to 3.11 ng ml-1 for ampicillin, with a detection limit of 0.04 ng ml-1. It exhibits significant selectivity and achieves an average recovery rate of 98.71% in tap water and 91.83% in milk. This method can be used not only for residual ampicillin detection, but also for highly sensitive detection of various antibiotics and small biological molecules by replacing the aptamer type. It provides a research basis for the design of highly sensitive fluorescence aptamer sensors and further applications of nanogold@DNA composite structures.

Effect of Sodium Laureth Sulfate on Contact Angles of High-Impact Polystyrene and Acrylonitrile–Butadiene–Styrene from Recycled Refrigeration Equipment

This paper investigates the effects of sodium laureth sulfate (SLES) on the wettability of the surface of the two most common recycled plastics in refrigeration equipment: HIPS (high-impact polystyrene) and ABS (acrylonitrile–butadiene–styrene). These plastics, in the form of flakes, were identified on the basis of their FTIR spectra, and then, they were subjected to a study of contact angles using the sessile droplet method. The solutions for the angle analysis included tap water with the addition of SLES. The results of this study showed that at SLES concentrations of 0.1 g/L and 0.2 g/L, the differences in the contact angles for HIPS and ABS were 10.76° and 10.10°, respectively. This research confirmed the potential of using SLES as a support for the flotation separation of plastics with similar densities and surface characteristics, such as HIPS and ABS.

Optimized Antibiotic Resistance Genes Monitoring Scenarios Promote Sustainability of Urban Water Cycle.

Dissemination of antibiotic resistance genes (ARGs) in urban water bodies has become a significant environmental and health concern. Many approaches based on real-time quantitative PCR (qPCR) have been developed to offer rapid and highly specific detection of ARGs in water environments, but the complicated and time-consuming procedures have hindered their widespread use. Herein, we developed a facile one-step approach for rapid detection of ARGs by leveraging the trans-cleavage activity of Cas12a and recombinase polymerase amplification (RPA). This efficient method matches the sensitivity and specificity of qPCR and requires no complex equipment. The results show a strong correlation between the prevalence of four ARG markers (ARGs: sul1, qnrA-1, mcr-1, and class 1 integrons: intl1) in tap water, human urine, farm wastewater, hospital wastewater, municipal wastewater treatment plants (WWTPs), and proximate natural aquatic ecosystems, indicating the circulation of ARGs within the urban water cycle. Through monitoring the ARG markers in 18 WWTPs in 9 cities across China during both peak and declining stages of the COVID epidemic, we found an increased detection frequency of mcr-1 and qnrA-1 in wastewater during peak periods. The ARG detection method developed in this work may offer a useful tool for promoting a sustainable urban water cycle.

Paper Spray Mass Spectrometry with On‐Paper Electrokinetic Manipulations: Part‐Per‐Trillion Detection of Per/Polyfluoroalkyl Substances in Water and Opioids in Urine

AbstractWe developed a simple, paper‐based device that enables sensitive detection by mass spectrometry (MS) without solid phase extraction or other sample preparation. Using glass fiber filter papers within a 3D printed holder, the device employs electrokinetic manipulations to stack, separate, and desalt charged molecules on paper prior to spray into the MS. Due to counter‐balanced electroosmotic flow and electrophoresis, charged analytes stack on the paper and desalting occurs in minutes. One end of the paper strip was cut into a sharp point and positioned near the inlet of a MS. The stacked analyte bands move toward the paper tip with the EOF where they are ionized by paper spray. The device was applied to analysis of PFAS in tap water with sub part‐per‐trillion detection limits in less than ten minutes with no sample pretreatment. Analysis of opioids in urine also occurs in minutes. The crucial parameters to enable stacking, separation, and MS ionization of both positively and negatively charged analytes were determined and optimized. Experimental and computational modeling studies confirm the electrokinetic stacking and analyte transport mechanisms. On‐paper separations were carried out by stacking analyte bands at different locations depending on their electrophoretic mobility, achieving baseline separation in some cases.

Protein Deposition on Sport Mouthguards and the Effectiveness of Two Different Cleaning Protocols

Objective: To determine which salivary proteins adhere onto sport mouthguards, and to evaluate the effectiveness of different cleaning strategies in removing deposited protein. Methods: Fifteen healthy volunteers used a mouthguard for 1 h. The deposited salivary proteins were analyzed using gel electrophoresis and Western blotting techniques and compared with the protein composition of unstimulated saliva. In addition, the effectiveness of two different cleaning strategies to remove proteins from the mouthguards were compared: rinsing the mouthguards after use with cold tap water and cleaning the mouthguard with a soluble effervescent tablet. Results: Gel electrophoresis showed deposition of proteins of 50–60 kDa and 14 kDa on the mouthguards used in the mouth for 1 h. Western blotting identified these bands as amylase and lysozyme, respectively. Rinsing the mouthguard with cold tap water after use removed 91% of the total amount of deposited proteins, while cleaning with an effervescent tablet removed 99%. Conclusions: During the use of mouthguards, salivary proteins are deposited on their surface. Because salivary proteins can potentially affect bacterial adhesion to mouthguards, proper cleaning after use is recommended. Cleaning the mouthguard with cold tap water or using an effervescent tablet both seem to be effective strategies to remove proteins deposited on sport mouthguards.

Drinking water sources, quality, and associated health outcomes in Appalachian Virginia: A risk characterization study in two counties

ObjectivesIn the US, violations of drinking water regulations are highest in lower-income rural areas overall, and particularly in Central Appalachia. However, data on drinking water use, quality, and associated health outcomes in rural Appalachia are limited. We sought to assess public and private drinking water sources and associated risk factors for waterborne pathogen exposures for individuals living in rural regions of Appalachian Virginia. MethodsWe administered surveys and collected tap water, bottled water, and saliva samples in lower-income households in two adjacent rural counties in southwest Virginia (bordering Kentucky and Tennessee). Water samples were tested for pH, temperature, conductivity, total coliforms, E. coli, free chlorine, nitrate, fluoride, heavy metals, and specific pathogen targets. Saliva samples were analyzed for antibody responses to potentially waterborne infections. We also shared water analysis results with households. ResultsWe enrolled 33 households (83 individuals), 82% (n = 27) with utility-supplied water and 18% with private wells (n = 3) or springs (n = 3). 58% (n = 19) reported household incomes of <$20,000/year. Total coliforms were detected in water samples from 33% (n = 11) of homes, E. coli in 12%, all with wells or springs (n = 4), and Aeromonas, Campylobacter, and Enterobacter in 9%, all spring water (n = 3). Diarrhea was reported for 10% of individuals (n = 8), but was not associated with E. coli detection. 34% (n = 15) of saliva samples had detectable antibody responses for Cryptosporidium spp., C. jejuni, and Hepatitis E. After controlling for covariates and clustering, individuals in households with septic systems and straight pipes had significantly higher likelihoods of antibody detection (risk ratios = 3.28, 95%CI = 1.01–10.65). ConclusionsTo our knowledge, this is the first study to collect and analyze drinking water samples, saliva samples, and reported health outcome data from low-income households in Central Appalachia. Our findings indicate that utility-supplied water in this region was generally safe, and individuals in low-income households without utility-supplied water or sewerage have higher exposures to waterborne pathogens.

Detection, detoxification, and anti-counterfeiting applications of pullulan-modified nitrogen-doped carbon dots

Nitrogen-doped carbon dots (N-CDs) modified with pullulan were prepared using a hydrothermal method for use in sensing, detoxification, and anti-counterfeiting applications. The excitation-independent N-CDs demonstrated selectivity for hydroquinone and 4-nitrophenol (4-NP) with detection limits of 58 and 13 nM. The N-CD-based detection method was extended to environmental samples such as bottled water, tap water, and river water, and acceptable relative standard deviations (RSDs) and good recoveries were found. In the presence of NaBH4, N-CDs converted the toxic MB to colorless leuco-methylene blue in 10.5 minutes, confirming that the catalytic ability of N-CDs can be evaluated using MB as a model pollutant. With an excellent quantum yield of 31%, the N-CDs had the potential as a fluorescent ink for anti-counterfeiting applications by helping to visualize fingerprints, drawings, and chemical structures under 365 nm UV light while being completely invisible in daylight and sunlight. The N-CDs have significant potential for industrial use as fluorescent inks, detoxification catalysts, and pollutant sensors.

Long-Term Consumption of Purified Water Altered Amino Acid, Fatty Acid and Energy Metabolism in Livers of Rats.

The consumption of low-mineral water has been increasing worldwide. Drinking low-mineral water is associated with cardiovascular disease, osteopenia, and certain neurodegenerative diseases. However, the specific mechanism remains unclear. The liver metabolic alterations in rats induced by drinking purified water for 3 months were investigated with a metabolomics-based strategy. Compared with the tap water group, 74 metabolites were significantly changed in the purified water group (6 increased and 68 decreased), including 29 amino acids, 11 carbohydrates, 10 fatty acids, 7 short chain fatty acids (SCFAs), and 17 other biomolecules. Eight metabolic pathways were significantly changed, namely aminoacyl-tRNA biosynthesis; nitrogen metabolism; alanine, aspartate and glutamate metabolism; arginine and proline metabolism; histidine metabolism; biosynthesis of unsaturated fatty acids; butanoate metabolism; and glycine, serine and threonine metabolism. These changes suggested that consumption of purified water induced negative nitrogen balance, reduced expression of some polyunsaturated fatty acids and SCFAs, and disturbed energy metabolism in rats. These metabolic disturbances may contribute to low-mineral-water-associated health risks. The health risk of consuming low-mineral water requires attention.

Investigating the Health Claims and Regulatory Considerations of Kangen Water: a Comprehensive Analysis with Python and Spiritual Insights

In recent years, Kangen water has emerged as a subject of intense interest due to its purported health benefits attributed to its alkaline nature. Produced via a process known as ionization, Kangen water exhibits a higher pH level compared to regular tap water, purportedly offering numerous health advantages. However, the scientific evidence supporting these claims remains ambiguous and inconclusive. This paper embarks on a thorough exploration of Kangen water, beginning with an elucidation of the electrolysis process fundamental to its creation. Following this, the alleged health benefits are scrutinized against the backdrop of existing scientific literature, delving into studies examining its impact on various health parameters. Furthermore, an in-depth analysis of the regulatory framework surrounding Kangen water is provided, shedding light on the legal and compliance aspects governing its production, distribution, and marketing. Additionally, pragmatic considerations such as cost-effectiveness, maintenance requirements, and consumer preferences are meticulously examined to offer a holistic perspective on the practical implications of Kangen water consumption. By synthesizing scientific research, regulatory insights, and practical considerations, this paper endeavors to furnish a comprehensive understanding of Kangen water, enabling consumers to make informed decisions regarding its usage while facilitating regulatory agencies in formulating appropriate guidelines to ensure public health and safety.

Hydrogen sulfide-mitigated salinity stress impact in sunflower seedlings was associated with improved photosynthesis performance and osmoregulation

BackgroundSalinity is one major abiotic stress affecting photosynthesis, plant growth, and development, resulting in low-input crops. Although photosynthesis underlies the substantial productivity and biomass storage of crop yield, the response of the sunflower photosynthetic machinery to salinity imposition and how H2S mitigates the salinity-induced photosynthetic injury remains largely unclear. Seed priming with 0.5 mM NaHS, as a donor of H2S, was adopted to analyze this issue under NaCl stress. Primed and nonprime seeds were established in nonsaline soil irrigated with tape water for 14 d, and then the seedlings were exposed to 150 mM NaCl for 7 d under controlled growth conditions.ResultsSalinity stress significantly harmed plant growth, photosynthetic parameters, the structural integrity of chloroplasts, and mesophyll cells. H2S priming improved the growth parameters, relative water content, stomatal density and aperture, photosynthetic pigments, photochemical efficiency of PSII, photosynthetic performance, soluble sugar as well as soluble protein contents while reducing proline and ABA under salinity. H2S also boosted the transcriptional level of ribulose 1,5-bisphosphate carboxylase small subunit gene (HaRBCS). Further, the transmission electron microscope showed that under H2S priming and salinity stress, mesophyll cells maintained their cell membrane integrity and integrated chloroplasts with well-developed thylakoid membranes.ConclusionThe results underscore the importance of H2S priming in maintaining photochemical efficiency, Rubisco activity, and preserving the chloroplast structure which participates in salinity stress adaptation, and possibly sunflower productivity under salinity imposition. This underpins retaining and minimizing the injury to the photosynthetic machinery to be a crucial trait in response of sunflower to salinity stress.

Comparison of ePTFE membranes with fluorine-free alternatives considering durability of laminated fabrics using hydrostatic pressure testing

Pleasant wearing comfort is achieved using laminated fabrics containing a waterproof and breathable membrane. The most used membrane type is expanded polytetrafluoroethylene. Due to the negative impact of perfluoroalkyl and polyfluoroalkyl substances on the environment, fluorine-free alternative materials are necessary. In this work, alternative membrane materials, polyurethane and polyethylene terephthalate, were compared with expanded polytetrafluoroethylene. First, the mass per unit area, thickness, tensile properties, water vapor resistance, and hydrostatic pressure of corresponding laminates were determined. Furthermore, their durability, which is an essential aspect of sustainability, was investigated. Therefore, they were hydrolyzed, weathered, washed, and incorrectly treated (e.g. washed with fabric softener) and then investigated for hydrostatic pressure resistance, by scanning electron microscopy, infrared spectroscopy, and digital microscopy. It was shown that polyethylene terephthalate and expanded polytetrafluoroethylene are comparable with respect to breathability, waterproofness (&gt;20 bar), and durability. However, the hydrostatic pressure resistance (approximately 11 bar) and the water vapor resistance values (&gt;23 m2 · Pa · W−1) of microporous polyurethane membranes are poorer, but they still provide suitable alternatives. In addition, a beginning degradation of polyurethane could be proved after hydrolysis and weathering. Furthermore, the deposition of calcium salts on all membranes was observed after washing with tap water, fabric softener, and washing agents.

Terbium Phenanthroline Complex as a Luminescent Probe for the Detection of Anthrax Biomarker: Dipicolinic acid.

Dipicolinic acid (DPA) is a prominent biomarker for Anthrax disease. Bacillus anthracis bacterial endospores is composed of DPA as the significant component, which on over inhalation can cause severe health issues. Such contagious and life-threatening pathogens can be employed as bioweapons or biothreat agents for spreading bioterrorism which is a major risk for national security and public health concerns. Hence, effective detection or a surveillance system is essential for preventing the growth of bioterrorism events. Herein, we have developed a Terbium - 1,10 Phenanthroline (Tb-Phen) based lanthanide luminescence complex with bright green fluorescence. On addition of DPA, the green fluorescence is turn-off at a linear range from 0.6 to 4.762 mM. In this effect, 5D4- 7F5 transition caused by 1,10-phenanthroline to Tb3+ at 544nm is restricted due to energy transfer quenching and Inner Filter Effect (IFE). The developed probe shows good sensitivity towards the detection of DPA with other coexisting biomolecules and ions with a low Limit of Detection (LOD) of 5.029 µM. The practical feasibility was evaluated in paper strip assay and extended in real samples such as human serum and tap water with satisfactory recovery percentage. Thereby, probe finds promising application in sensing of anthrax spore biomarker (DPA) and biothreat agents.

Pentacenequinone-Modulated 2D GdSn-PQ Nanosheets as a Fluorescent Probe for the Detection of Enrofloxacin in Biological and Environmental Samples.

The fate and effects of fluoroquinolone antibacterial (FQ) on the environment are important since there appears to be a surge in FQ resistance like enrofloxacin (ENR) in both environmental and clinical organisms. Numerous reports indicate that the sensing capabilities of these antibiotics need to be improved. Here, we have investigated the interaction of ENR with our synthesized pentacenequinone-modulated gadolinium-tin (GdSn-PQ) nanosheets and the formation of intermolecular interactions that caused the occurrence of aggregation-induced emission enhancement. The concept for designing hybrid metallic nanosheets comes from the unique features inherited from the parent organic precursor. Due to the distinct interaction between ENR and GdSn-PQ, the interstate conversion (ISC) between GdSn-PQ and ENR induces a significant wavelength shift in photoluminescence (PL), improving reliability, selectivity, and visibility compared to quenching- or AIEE-based methods without peak shifts, allowing for highly sensitive and visually detectable analyses. The fluorescence signal of GdSn-PQ exhibited a linear relationship (R2 = 0.9911), with the added ENR concentrations ranging from 5 to 90 nM, with a detection limit of 0.10 nM. We have demonstrated its potential and wide use in the detection of ENR in biological samples (human urine and blood serum) and environmental samples (tap water and seawater) with a recovery rate of 98- 108%. The current approach has demonstrated that the 2D GdSn-PQ nanosheet is a novel and powerful platform for future biological and environmental studies.

Analysing the interlinkage between diarrhoea and drinking water faecal contamination in India

ABSTRACT Diarrhoea is one of the major waterborne diseases spread through the faecal–oral route causing over 10 million cases and over 1,000 deaths in India. This study critically evaluates the interlinkage between bacteriological water quality, i.e. faecal coliforms and diarrhoea cases for the three pre-pandemic years 2017, 2018 and 2019 based on multiple sources. With around 17% of households tap water connectivity as of August 2019, the majority of the Indian population depends on raw groundwater (GW) and surface water sources. For this, faecal coliform (FC) levels in surface and GW have been mapped at district levels using data from India's National Water Quality Monitoring Programme. Health Management Information System's data on diarrhoea have been used to understand the monthly and district-wise variation of diarrhoea. The trends of FC, diarrhoea inpatient cases, and diarrhoea inpatient rates have been discussed. The analysis showed issues associated with the reliability and usefulness of these datasets with 43% of total India districts with no reported FC values for the study period. This study reveals a clear gap in the interlinkage between diarrhoea and bacteriological water quality with the unavailability of granular water quality data as a major challenge.

Azolla filiculoides extract improved salt tolerance in wheat (Triticum aestivum L.) is associated with prompting osmostasis, antioxidant potential and stress-interrelated genes

The growth and productivity of crop plants are negatively affected by salinity-induced ionic and oxidative stresses. This study aimed to provide insight into the interaction of NaCl-induced salinity with Azolla aqueous extract (AAE) regarding growth, antioxidant balance, and stress-responsive genes expression in wheat seedlings. In a pot experiment, wheat kernels were primed for 21 h with either deionized water or 0.1% AAE. Water-primed seedlings received either tap water, 250 mM NaCl, AAE spray, or AAE spray + NaCl. The AAE-primed seedlings received either tap water or 250 mM NaCl. Salinity lowered growth rate, chlorophyll level, and protein and amino acids pool. However, carotenoids, stress indicators (EL, MDA, and H2O2), osmomodulators (sugars, and proline), antioxidant enzymes (CAT, POD, APX, and PPO), and the expression of some stress-responsive genes (POD, PPO and PAL, PCS, and TLP) were significantly increased. However, administering AAE contributed to increased growth, balanced leaf pigments and assimilation efficacy, diminished stress indicators, rebalanced osmomodulators and antioxidant enzymes, and down-regulation of stress-induced genes in NaCl-stressed plants, with priming surpassing spray in most cases. In conclusion, AAE can be used as a green approach for sustaining regular growth and metabolism and remodelling the physio-chemical status of wheat seedlings thriving in salt-affected soils.

Synthesis of highly luminescent core-shell nanoprobes in a single pot for ofloxacin detection in blood serum and water.

Antibiotics are commonly used as antibacterial medications due to their extensive and potent therapeutic properties. However, the overconsumption of these chemicals leads to their accumulation in the human body via the food chain, amplifying drug resistance and compromising immunity, thus presenting a significant hazard to human health. Antibiotics are classified as organic pollutants. Therefore, it is crucial to conduct research on precise methodologies for detecting antibiotics in many substances, including food, pharmaceutical waste, and biological samples like serum and urine. The methodology described in this research paper introduces an innovative technique for producing nanoparticles using silica as the shell material, iron oxide as the core material, and carbon as the shell dopant. By integrating a carbon-doped silica shell, this substance acquires exceptional fluorescence characteristics and a substantial quantum yield value of 80%. By capitalising on this characteristic of the substance, we have effectively constructed a fluorescent sensor that enables accurate ofloxacin analysis, with a detection limit of 1.3 × 10-6 M and a linear range of concentrations from 0 to 120 × 10-6 M. We also evaluated the potential of CSIONPs for OLF detection in blood serum and tap water analysis. The obtained relative standard deviation values were below 3.5%. The percentage of ofloxacin recovery from blood serum ranged from 95.52% to 103.28%, and from 89.9% to 96.0% from tap water.

The prevalence of hospital acquired infection and associated factors among patients admitted at Wolaita Sodo University Comprehensive Specialized Hospital, in Ethiopia

Hospital-acquired infection is an infection acquired a major global concern of well-being, affecting the quality of care in the healthcare setting. Routine surveillance of infection is an important part of infection prevention and quality assurance in hospitals. to determine the prevalence and associated factors of hospital-acquired infection among inpatients, in Wolaita Sodo University Comprehensive Specialized Hospital.Across-sectional study was conducted among inpatients in Wolaita Sodo University Comprehensive Specialized Hospital. All eligible inpatients admitted at least more three days of the survey were included. The study was conducted from April 1 to July 30/2023. Environmental health professionals and nurses collected the data according to the Centers for Disease Control through observational assessments documented by physicians. Univariate and multivariable logistic regression analyses were used to determine the prevalence of hospital-acquired infections and the associations between independent and dependent variables. A total of 413 patients were included in this study, the median age of the participants was 26 years. A total of 352 (85.2%) patients were diagnosed with non-fatal disease during the survey. 49 patients had hospital-acquired infections developed, with a mean prevalence of 11.9 %. Coagulate-negative staphylococcus 27.27%), and E. coli (27.27) were the most frequently reported hospital-acquired infection-causing pathogens from the result of the study. The factors of patient admission diagnosis, length of hospital stay (more than five days of hospital stay), and absence of running tap water in the patient’s room with the occurrence of hospital-acquired infection were statistically significant.Surgical site infections and bloodstream infections were the most common types of hospital-acquired infections. Then, Hospital management and healthcare workers should give more attention to the practice of infection prevention to achieve a reduced prevalence of hospital-acquired infections in the study setting.

Microwave-Assisted Synthesis of SnO2@ZnIn2S4 Composites for Highly Efficient Photocatalytic Hydrogen Evolution.

This research successfully synthesized SnO2@ZnIn2S4 composites for photocatalytic tap water splitting using a rapid two-step microwave-assisted synthesis method. This study investigated the impact of incorporating a fixed quantity of SnO2 nanoparticles and combining them with various materials to form composites, aiming to enhance photocatalytic hydrogen production. Additionally, different weights of SnO2 nanoparticles were added to the ZnIn2S4 reaction precursor to prepare SnO2@ZnIn2S4 composites for photocatalytic hydrogen production. Notably, the photocatalytic efficiency of SnO2@ZnIn2S4 composites is substantially higher than that of pure SnO2 nanoparticles and ZnIn2S4 nanosheets: 17.9-fold and 6.3-fold, respectively. The enhancement is credited to the successful use of visible light and the facilitation of electron transfer across the heterojunction, leading to the efficient dissociation of electron-hole pairs. Additionally, evaluations of recyclability demonstrated the remarkable longevity of SnO2@ZnIn2S4 composites, maintaining high levels of photocatalytic hydrogen production over eight cycles without significant efficiency loss, indicating their impressive durability. This investigation presents a promising strategy for crafting and producing environmentally sustainable SnO2@ZnIn2S4 composites with prospective implementations in photocatalytic hydrogen generation.

Microplastics and non-natural cellulosic particles in Spanish bottled drinking water

This investigation explored the presence of microplastics (MPs) and artificial cellulosic particles (ACPs) in commercial water marketed in single use 1.5 L poly(ethylene terephthalate) bottles. In this work we determined a mass concentration of 1.61 (1.10–2.88) µg/L and 1.04 (0.43–1.82) µg/L for MPs and ACPs respectively in five top-selling brands from the Spanish bottled water market. Most MPs consisted of white and transparent polyester and polyethylene particles, while most ACPs were cellulosic fibers likely originating from textiles. The median size of MPs and ACPs was 93 µm (interquartile range 76–130 µm) and 77 µm (interquartile range 60–96 µm), respectively. Particle mass size distributions were fitted to a logistic function, enabling comparisons with other studies. The estimated daily intake of MPs due to the consumption of bottled water falls within the 4–18 ng kg−1 day−1 range, meaning that exposure to plastics through bottled water probably represents a negligible risk to human health. However, it's worth noting that the concentration of plastic found was much higher than that recorded for tap water, which supports the argument in favour of municipal drinking water.

Molecularly Imprinted Polymer-Based Electrochemical Sensor for the Detection of Azoxystrobin in Aqueous Media.

This work presents an electrochemical sensor detecting a fungicide-azoxystrobin (AZO) in aqueous environments. This AZO sensor utilizes a thin-film metal electrode (TFME) combined with an AZO-selective molecularly imprinted polymer (AZO-MIP). The AZO-MIP was directly generated on TFME through electrochemical polymerization from the solution containing two functional monomers: aniline (Ani) and m-phenylenediamine (mPD), and the template: AZO, which was afterwards removed to form AZO-selective cavities in the polymer matrix. The AZO-MIP preparation was characterized by electrochemical and ellipsometry measurements. Optimization of the synthesis parameters, including the charge density applied during electrodeposition, the monomer-to-template ratio, was performed to enhance the sensor's performance. The results demonstrated that the AZO sensor achieved a low limit of detection (LOD) of 3.6 nM and a limit of quantification (LOQ) of 11.8 nM in tap water, indicating its sensitivity in a complex aqueous environment. The sensor also exhibited satisfactory selectivity for AZO in both ultrapure and tap-water samples and achieved a good recovery (94-119%) for the target analyte. This study highlights the potential of MIP-based electrochemical sensors for the rapid and accurate detection of fungicide contaminants in water, contributing to the advancement of analytical tools for water-quality monitoring and risk assessment.