Cell System Research Articles

Techno-economic analysis and fuel applicability study of a novel gasifier-SOFC distributed energy system with CO2 capture and freshwater production

This study employs the water-gas-shift membrane reactor and multi-effect distillation with thermal vapor compression technologies to facilitate low-energy carbon capture and large-scale freshwater production in gasifier-solid oxide fuel cell (SOFC) systems. The supercritical CO2 Brayton cycle and double-effect absorption refrigeration cycle are introduced to achieve waste heat cascade recovery. This work expands the fuel selection to 12 biomasses to explore the fuel adaptability and application scenarios of the system, and selects four representative cases to reveal their thermodynamic and economic attributes. The base scheme produces 21,635 ton/year freshwater and 1333 ton/year CO2, and achieves energy and exergy efficiencies of 70.68 % and 30.60 % with total cost rate of 23.21 $/h and levelized cost of products of 43.55 $/GJ. The gasifier and SOFC effort contributes to over 60 % of total irreversibility. Larch wood is preferred in resource-rich regions while wood residue, switch grass and wood chip are also prioritized; rice straw, rice husk, cotton stem and algal biomass are suitable for water-scarce areas. As key parameters change, Case-II consistently excels in power output, efficiencies and economic aspects, but lags in cooling capacity compared with other cases. This work provides a reference for low-carbon transition in the energy sector and large-scale freshwater production.

Performance evaluation and economic analysis of integrated solid oxide electrolyzer cell and proton exchange membrane fuel cell for power generation

In order to generate clean electricity from thermal energy, a hybrid electrochemical system is conceptually developed by coupling the proton exchange membrane fuel cell (PEMFC) and solid oxide electrolyzer cell (SOEC). For evaluating the proposed hybrid system, firstly, the two subsystems are modeled numerically and then they are merged into an integrated SOEC-PEMFC system. Moreover, the SOEC-PEMFC is analytically modeled for further evaluation. The effects of important operational parameters are examined. The outcomes show that when the SOEC operating temperature increases from 823 to 1273 K, the efficiency increases from 18.7% to 38% and the net output power improves about 36% while cost per unit of power of hybrid system decreases about 80%. Furthermore, by increasing the PEMFC operating temperature from 323 to 348 K, the system net output power and efficiency increase about 16.7% and 10%, respectively, whilst the cost per unit of electricity decreases about 19%. In addition by increasing operating pressure of system, the net output power and efficiency are also improved. The proposed system has maximum output power density of 3.9 kW.m-2 and maximum efficiency of 38%. In addition, the SOEC-PEMFC system is compared with the previously studied proton exchange membrane electrolyzer cell-proton exchange membrane fuel cell (PEMEC-PEMFC) system. In comparison with the previous PEMEC-PEMFC system, the present system's cost per unit of power and efficiency are about 16% and 17% higher, respectively; while the output power density is about double that of the PEMEC-PEMFC system. Generally, because hydrogen-powered systems offer reliable operation from an economic and energetic perspective, the SOEC-PEMFC system represents a promising technological solution to the clean energy demands.

Enhanced proton conductivity and mechanical stability of crosslinked sodium alginate as a biopolymer electrolyte membrane in fuel cell application

Abstract Nafion is a commercial polymer membrane that is commonly used in fuel cell systems, despite its major limitations such as high fuel crossover and high manufacture cost. The production of sodium alginate (SA) blended membrane with crosslinking agent (glutaraldehyde) and plasticizer (glycerol) is one of several current efforts to discover an alternative membrane with improved proton conductivity and mechanical properties. In this study, SA biomembranes were prepared using solution casting method and dried at a certain temperature. Then, the prepared membranes were immersed with 5% glycerol in different concentrations of glutaraldehyde. The cross-linked biomembranes underwent various tests such as liquid uptake, swelling ratio, ion exchange capacity, proton conductivity and mechanical stability. The best membrane achieved the highest proton conductivity with a value of 8.28 mS cm-1 and mechanical stability with a value of 218.00 MPa. Glutaraldehyde made a positive modification and had a beneficial impact on the characteristics of SA. The incorporation of glutaraldehyde and glycerol within the biopolymer notably improved the otherwise lacking mechanical properties of SA.

Enhancing the efficiency of medium-scale dual-chamber microbial fuel cell systems through the utilization of novel electrodes material and proper selection of catholyte and external resistance

Dual-chamber microbial fuel cells (DC-MFC) are devices that can be used to generate electricity through the degradation of substrates. In this study, the performance of DC-MFC with novel electrode materials is evaluated under different external resistance using a hydrochloric acid solution as catholyte. Hydrophilic-treated graphene was used as the electrode material, DuPontTM Nafion 117 was used as the proton exchange membrane and domestic wastewater served as the substrate. The maximum power density achieved was 32.05 mW⋅m−2, obtained by degrading 69.8% of organic matter when an external resistance of 100 Ω was used as electrical load. This power density was 32 times higher than the power density obtained in the control (1.01 mW⋅m−2). This result obtained was similar to those reported in the literature for small-scale DC-MFC systems. And, contrary to the reported trend that as the scale of MFCs increase, the efficiency decreases. It can be stipulated with these results that is possible to scale up DC-MFC to medium-scale systems without loss performance quality by selecting the appropriate external resistance, catholyte and electrode materials.

Evaluation of emergency skin decontamination protocols in response to an acid attack (vitreolage)

The incidence of “acid attacks” (vitreolage) is a global concern, with those affected often receiving lifelong medical care due to physical and psychological damage. The purpose of this study was to evaluate the effectiveness of several emergency skin decontamination approaches against concentrated (>99 %) sulphuric acid and to identify the effective window of opportunity for decontamination. The effects of four decontamination methods (dry, wet, combined dry & wet and cotton cloth) were assessed using an in vitro diffusion cell system containing dermatomed porcine skin. Sulphuric acid (H2SO4) was applied to the skin with decontamination protocols performed at 10 s, 30 s, 8 min, and 30 min post exposure. Skin damage was quantified by tritiated water (3H2O) penetration, receptor fluid pH and photometric stereo imaging (PSI), with quantification of residual sulphur (by SEM-EDS) to determine overall decontamination efficiency. Skin translucency (quantified by PSI) demonstrated a time-dependent loss of dermal tissue integrity from 10 s. Quantification of dermal sulphur content confirmed the rapid (exponential) decrease in decontamination efficiency with time. The pH of the water effluent indicated complete neutralisation of acid from the skin surface after 90 s of irrigation. Wet decontamination (either alone or immediately following dry decontamination) was the most effective intervention evaluated, although no decontamination technique was statistically effective after 30 s exposure to the acid. These data demonstrate the time-critical consequences of dermal exposure to concentrated sulphuric acid: we find no practical window of opportunity for acid decontamination, as physical damage is virtually instantaneous.

Interferon-stimulated gene (ISG12a) suppresses hepatitis B virus replication in Huh 7 cells line

Hepatitis B virus (HBV) and its associated chronic liver disease pose a significant health hazard. Chronic HBV infection is a major contributor to the development of liver cirrhosis, liver fibrosis, and liver cancer. This study focused on ISG12a and its inhibitory effect in Huh7 cells on HBV gene expression and replication. The mammalian hepatoma cells Huh7 were transfected with the pHBV1.3 vector (pCAGGS) or HA-tagged ISG12a to determine the overexpression, to test this hypothesis further, we did knockdown or silencing by transducing Huh7 cells with lentiviruses containing shRNAs targeting ISG12a or scramble control shRNA (shControl). The expression of ISG12a was evaluated through western blot analysis. The HBsAg and HBeAg secretion in the Huh7 cells’ culture media was examined using an ELISA test. The qRT-PCR confirmed the mRNA and 3.5 mRNA Kb of ISG12a. The HBV total RNA was extracted and evaluated through a Northern blot. The isolated DNA was detected through qPCR. Additionally, a mechanistic study of enhancer II (EnhII/Cp) was examined through luciferase reporter testing. Our research findings indicate that ISG12a, an interferon-stimulated gene (ISG), plays a crucial role in suppressing the replication and gene expression of HBV. According to our study using the Huh7 cell system, overexpression of ISG12a resulted in a notable reduction in HBV protein levels as well as intracellular core-associated DNA and RNA levels. On the other hand, silencing ISG12a in Huh7 cells resulted in increased HBV RNA transcripts, DNA, and secreted proteins, indicating that ISG12a plays a role in suppressing HBV replication. Additionally, the research revealed that ISG12a inhibits the function of the EnhII/Cp promoter, which results in reduced HBV gene expression. The EnhII/Cp promoter is involved in regulating HBV gene expression, and the study showed that ISG12a restricts its activity. ISG12a may have a regulatory role in controlling the expression of HBV genes. These findings highlight the importance of ISG12a in HBV gene expression and provide valuable insights for understanding its antiviral function.

Interplay between the heat treatment and structural and optical properties of Nb2O5 thin films

Thin films of Nb2O5 were synthesized by RF sputtering. The effect of annealing, at different temperatures (100, 150, 200, 250, 300, 350, and 400 °C), on the structural and optical properties was studied. The crystallinity and structural characteristics of the Nb2O5 thin films were examined employing the X-ray diffraction (XRD) and scanning electron microscopy (SEM). XRD and SEM analyses showed an amorphous nature for the as-deposited and annealed samples from 100 to 350 °C and crystalline structure for the annealed sample at 400 °C. The high values of the transmittance and low reflection make these films used as a window layer in solar cell systems. Upon increasing annealing temperature, the energy band gap Eg increased from 4.039 to 4.175 eV. Eg high values again make these films suitable to be used as a window layer in solar cell system. Urbach tail, EU, decreased with increasing annealing temperature. The refractive index showed the normal dispersion. The dispersion energies were found to have the same behavior with respect to annealing temperature, besides, the single oscillator energy Eₒ had a lower value compared to the dispersion energy Ed. The plasma frequency ωp\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${\\omega }_{p}$$\\end{document} was found to increase with annealing temperature. The first and third optical moments had peak values depending on the incident photon energy.

Integrated Controller for Fuel Cell Systems: A Full-loop Architecture

Abstract In response to the global initiative towards hydrogen energy, increasing focus has been placed on enhancing the performance, reliability and endurance of fuel cells by utilizing advanced control and monitoring strategies. However, due to the multi-variable. multi-loop and multi-physics nature of hydrogen fuel cells, the current decentralized architecture, where fuel cell controllers are isolated and placed in separate enclosures is no longer sufficient to carry out intricate coordinated control strategies. To this end, in this paper, we introduce a novel full-loop architecture, which enables the integration of the fuel cell controller, the air compressor controller, and the power electronics controller within one enclosure, reducing system size and cost. Moreover, based on the integrated hardware architecture, coordinated control such as oxygen/hydrogen pressure coordination can be carried out efficiently. A case study on electrochemical impedance spectroscopy has been conducted, demonstrating the advanced control and monitoring capabilities of this controller architecture.

Innovative Air Supply Management in Fuel Cells: An Economic Predictive Control Approach Without Pre-measured OER

Existing fuel cell air supply control methods improve the economic performance of Proton Exchange Membrane Fuel Cells (PEMFC) under steady-state conditions through oxygen excess ratio curve, while ignoring the transient process of the air supply system under varying operating conditions. Furthermore, the oxygen excess ratio curve may exhibit deviations due to fuel cell aging and measurement inaccuracies, which would further diminish the economic performance derived from the control process. Not relying on pre-measuring the oxygen excess ratio curve, an EMPC (Economic Model Predictive Control) method is proposed for fuel cell air supply systems. It incorporates an economic cost function reflecting the economic objectives of the air supply system. By dynamically optimizing the parasitic power of the air compressor, this method enhances the overall economic performance by achieving performance optimization for both transient and steady-state processes of the fuel cell system. The asymptotic stability of PEMFC is achieved through the utilization of terminal penalty functions and terminal domain constraints. Stability and convergence analysis is carried out by employing auxiliary optimization problems and the Lyapunov method. In transient processes, EMPC method can achieve a maximum 4.97% improvement in the economic performance of PEMFC. A hardware in loop (HIL) experiment was finally conducted to show the real-time capacity of the proposed EMPC method.

Evaluation of Emergency Skin Decontamination Protocols in Response to an Acid Attack (Vitreolage).

The incidence of “acid attacks” (vitreolage) is a global concern, with victims often requiring lifelong medical care due to physical and psychological damage. The purpose of this study was to evaluate the effectiveness of several emergency skin decontamination approaches against concentrated (>99%) sulphuric acid and to identify the effective window of opportunity for decontamination.The effects of four decontamination methods (dry, wet, combined dry & wet and cotton cloth) were assessed using an in vitro diffusion cell system containing dermatomed porcine skin. Sulphuric acid (H2SO4) was applied to the skin with decontamination protocols performed at 10seconds, 30seconds, 8minutes, and 30minutes post exposure. Skin damage was quantified by tritiated water (3H2O) penetration, receptor fluid pH and photometric stereo imaging (PSI), with quantification of residual sulphur (by SEM-EDS) to determine overall decontamination efficiency.Skin translucency (quantified by PSI) demonstrated a time-dependent loss of dermal tissue integrity from 10seconds. Quantification of dermal sulphur content confirmed the rapid (exponential) decrease in decontamination efficiency with time. The pH of the water effluent indicated complete neutralisation of acid from the skin surface after 90seconds of irrigation. Wet decontamination (either alone or immediately following dry decontamination) was the most effective intervention evaluated, although no decontamination technique was statistically effective after 30seconds exposure to the acid.These data demonstrate the time-critical consequences of dermal exposure to concentrated sulphuric acid: there is no practical window of opportunity for acid decontamination, as physical damage is virtually instantaneous.

Energy Management Considering both Efficiency Optimization and Lifetime Balance of Multi-stack FCS

Abstract With the increase of energy transformation and environmental protection awarenesses, fuel cells, as a clean and efficient energy conversion technology, have been widely adopted in transportation and stationary power supply applications. A single fuel cell has a limited power capability. On the other hand, the multiple fuel cells are combined into a multi-stack fuel cell system (MFCS), which provides a high power output and modular design. However, the energy management of such multi-stack systems faces challenges such as uneven power distribution, inconsistent stack life, and low overall efficiency. Current multi-stack fuel cell control systems often optimize single objectives, either efficiency or lifetime balance produce the optimized energy management strategy. This may not suffice for the overall system benefit. For example, if only efficiency is optimized by energy management, the failure to consider lifetime balance may result in uneven life degradation for each fuel cell, and vice versa. To address the above issues, this paper proposes an energy management strategy for multi-stack fuel cell systems that considers dual objectives, which can simultaneously ensure the optimal co-optimization of the output efficiency and stack life for each stack, thereby improving the overall operating efficiency and lifetime of the system. The effectiveness and practicality of the proposed energy management control strategy were verified on a 60kW dual-stack PEMFC fixed power generation system developed by SeeEx.

Ectoine enhances recombinant antibody production in Chinese hamster ovary cells by promoting cell cycle arrest

Chinese hamster ovary (CHO) cells represent the most preferential host cell system for therapeutic monoclonal antibody (mAb) production. Enhancing mAb production in CHO cells can be achieved by adding chemical compounds that regulate the cell cycle and cell survival pathways. This study investigated the impact of ectoine supplementation on mAb production in CHO cells. The results showed that adding ectoine at a concentration of 100 mM on the 3rd day of cultivation improved mAb production by improving cell viability and extending the culture duration. RNA sequencing analysis revealed differentially expressed genes associated with cell cycle regulation, cell proliferation, and cellular homeostasis, in particular promotion of cell cycle arrest, which was then confirmed by flow cytometry analysis. Ectoine-treated CHO cells exhibited an increase in the number of cells in the G0/G1 phase. In addition, the cell diameter was also increased. These findings support the hypothesis that ectoine enhances mAb production in CHO cells through mechanisms involving cell cycle arrest and cellular homeostasis. Overall, this study highlights the potential of ectoine as a promising supplementation strategy to enhance mAb production not only in CHO cells but also in other cell lines.

A Reliable System for Quantitative G-Protein Activation Imaging in Cancer Cells.

Fluorescence resonance energy transfer (FRET) biosensors have proven to be an indispensable tool in cell biology and, more specifically, in the study of G-protein signalling. The best method of measuring the activation status or FRET state of a biosensor is often fluorescence lifetime imaging microscopy (FLIM), as it does away with many disadvantages inherent to fluorescence intensity-based methods and is easily quantitated. Despite the significant potential, there is a lack of reliable FLIM-FRET biosensors, and the data processing and analysis workflows reported previously face reproducibility challenges. Here, we established a system in live primary mouse pancreatic ductal adenocarcinoma cells, where we can detect the activation of an mNeonGreen-Gαi3-mCherry-Gγ2 biosensor through the lysophosphatidic acid receptor (LPAR) with 2-photon time-correlated single-photon counting (TCSPC) FLIM. This combination gave a superior signal to the commonly used mTurquoise2-mVenus G-protein biosensor. This system has potential as a platform for drug screening, or to answer basic cell biology questions in the field of G-protein signalling.

Oxidative stress and metabolic process responses of Chlorella pyrenoidosa to nanoplastic exposure: Insights from integrated analysis of transcriptomics and metabolomics

Oxidative stress is a universal interpretation for the toxicity mechanism of nanoplastics to microalgae. However, there is a lack of deeper insight into the regulation mechanism in microalgae response to oxidative stress, thus affecting the prevention and control for nanoplastics hazard. The integrated analysis of transcriptomics and metabolomics was employed to investigate the mechanism for the oxidative stress response of Chlorella pyrenoidosa to nanoplastics and subsequently lock the according core pathways and driver genes induced. Results indicated that the linoleic acid metabolism, glycine (Gly)-serine (Ser)-threonine (Thr) metabolism, and arginine and proline metabolism pathways of C. pyrenoidosa were collectively involved in oxidative stress. The analysis of linoleic acid metabolism suggested that nanoplastics prompted algal cells to secrete more allelochemicals, thereby leading to destroy the immune system of cells. Gly-Ser-Thr metabolism and arginine and proline metabolism pathways were core pathways involved in algal regulation of cell membrane function and antioxidant system. Key genes, such as LOX2.3, SHM1, TRPA1, and proC1, are drivers of regulating the oxidative stress of algae cells. This investigation lays the foundation for future applications of gene editing technology to limit the hazards of nanoplastics on aquatic organism.

Multicolor, Cell-Impermeable, and High Affinity BACE1 Inhibitor Probes Enable Superior Endogenous Staining and Imaging of Single Molecules.

The prevailing but not undisputed amyloid cascade hypothesis places the β-site of APP cleaving enzyme 1 (BACE1) center stage in Alzheimer's Disease pathogenesis. Here, we investigated functional properties of BACE1 with novel tag- and antibody-free labeling tools, which are conjugates of the BACE1-inhibitor IV (also referred to as C3) linked to different impermeable Alexa Fluor dyes. We show that these fluorescent small molecules bind specifically to BACE1, with a 1:1 labeling stoichiometry at their orthosteric site. This is a crucial property especially for single-molecule and super-resolution microscopy approaches, allowing characterization of the dyes' labeling capabilities in overexpressing cell systems and in native neuronal tissue. With multiple colors at hand, we evaluated BACE1-multimerization by Förster resonance energy transfer (FRET) acceptor-photobleaching and single-particle imaging of native BACE1. In summary, our novel fluorescent inhibitors, termed Alexa-C3, offer unprecedented insights into protein-protein interactions and diffusion behavior of BACE1 down to the single molecule level.

Cellular uptake of FITC-labeled Ce0.8Gd0.2O2-x nanoparticles in 2D and 3D mesenchymal stem cell systems

Cellular uptake of FITC-labeled Ce0.8Gd0.2O2-x nanoparticles in 2D and 3D mesenchymal stem cell systems

Sustainable kitchen wastewater treatment with electricity generation using upflow biofilter-microbial fuel cell system.

The microbial fuel cell (MFC) is considered a modern technology used for treating wastewater and recovering electrical energy. In this study, a new dual technology combining MFC and a specialized biofilter was used. The anodic materials in the system were crushed graphite, either without coating (UFB-MFC) or coated with nanomaterials (nano-UFB-MFC). This biofilter served as a barrier to retain and remove turbidity and suspended solids, while also facilitating the role of bacteria in the removal of organic pollutants, phosphates, nitrates, sulfates, oil and greases. The results demonstrated that both systems exhibited high efficiency in treating kitchen wastewater, specifically greywater and dishwashing wastewater with high detergent concentrations. The removal efficiencies of COD, oil and grease, suspended solids, turbidity, nitrates, sulfates, and phosphates in first UFB-MFC were found to be 88, 95, 89, 86, 87, 75, and 94%, respectively, and in Nano-UFB-MFC were 86, 99, 95, 91, 81, 88, and 95%, respectively, with a high efficiency in recovering bioenergy reaching a value of 1.8 and 1.5Am-3, respectively. The results of this study demonstrate the potential for developing MFC and utilizing it as a domestic system to mitigate pollution risks before discharging wastewater into the sewer network.

Matching Together Living Cells and Prototissues: Will There Be Chemistry?

Scientific advancements in bottom-up synthetic biology have led to the development of numerous models of synthetic cells, or protocells. To date, research has mainly focused on increasing the (bio)chemical complexity of these bioinspired micro-compartmentalized systems, yet the successful integration of protocells with living cells remains one of the major challenges in bottom-up synthetic biology. In this review, we aim to summarize the current state of the art in hybrid protocell/living cell and prototissue/living cell systems. Inspired by recent breakthroughs in tissue engineering, we review the chemical, bio-chemical, and mechano-chemical aspects that hold promise for achieving an effective integration of non-living and living matter. The future production of fully integrated protocell/living cell systems and increasingly complex prototissue/living tissue systems not only has the potential to revolutionize the field of tissue engineering, but also paves the way for new technologies in (bio)sensing, personalized therapy, and drug delivery.

Modulation of the Human Erythrocyte Antioxidant System by the 5- and 6-Membered Heterocycle-Based Nitroxides.

Nitroxides are stable radicals consisting of a nitroxyl group, >N-O•, which carries an unpaired electron. This group is responsible for the paramagnetic and antioxidant properties of these compounds. A recent study evaluated the effects of pyrrolidine and pyrroline derivatives of nitroxides on the antioxidant system of human red blood cells (RBCs). It showed that nitroxides caused an increase in the activity of superoxide dismutase (SOD) and the level of methemoglobin (MetHb) in cells (in pyrroline derivatives) but had no effect on the activity of catalase and lactate dehydrogenase. Nitroxides also reduced the concentration of ascorbic acid (AA) in cells but did not cause any oxidation of proteins or lipids. Interestingly, nitroxides initiated an increase in thiols in the plasma membranes and hemolysate. However, the study also revealed that nitroxides may have pro-oxidant properties. The drop in the AA concentration and the increase in the MetHb level and in SOD activity may indicate the pro-oxidant properties of nitroxides in red blood cells.

Overexpression of ubiquitin-conjugating enzyme 2T induces radiotherapy resistance in hepatocellular carcinoma by enriching regulatory T cells in the tumor microenvironment

To investigate the effect of overexpression of ubiquitin-conjugating enzyme 2T (UBE2T) on radiosensitivity of hepatocellular carcinoma (HCC). Hepa1-6 cells were transfected with a UBE2T-overexpressing or a control lentiviral vector, and the changes in their radiotherapy sensitivity and concentrations of glucose and lactate in the supernatant were assessed using colony-forming assay and colorimetric assay. The transfected cells were inoculated subcutaneously in nude mice or C57BL/6 mice, and tumor growth following irradiation were recorded. The xenografts were collected for analyzing infiltration of CD4+ T cells and regulatory T cells (Tregs) using flow cytometry and detecting expressions of HK1 and LDHA using Western blotting. The correlations of UBE2T expression with immune cell infiltration, glycolysis and Tregs in HCC were analyzed using CIBERSORT algorithm and TCGA database, and the results were verified in a co-culture system of Hepa1-6 cells and Tregs. UBE2T overexpression caused radiotherapy resistance in both cultured Hepa1-6 cells and xenografts in the tumor-bearing mouse models (especially in C57BL/6 mice). CIBERSORT analysis suggested that a high expression of UBE2T was associated with increased percentages of dendritic cells, T follicular helper cells, M2 macrophages, monocytes, lymphocytes and Tregs in HCC. The UBE2T-overexpressing xenografts showed an increased percentage of Tregs and enhanced expressions of HK1 and LDHA, and irradiation increased infiltration of CD4+ T cells and Tregs in the tumor microenvironment. Hepa1-6 cells overexpressing UBE2T showed a decreased glucose concentration and an increased lactate concentration. GSEA analysis suggested that a high UBE2T expression was positively correlated with increased glycolysis and Tregs infiltration in HCC. In the cell co-culture system, UBE2T overexpression significantly enhanced lactate production, proliferation and immunosuppressive functions of Tregs. A high UBE2T expression results in radiotherapy resistance of HCC possibly by enhancing glycolysis and cause enrichment of Tregs in the tumor microenvironment.