Preconcentration System Research Articles

An on-line cloud point extraction system for flame atomic absorption spectrometric determination of trace manganese in food samples

The development of an on-line preconcentration system with cloud point extraction for the determination of manganese is described. The system was used to determine manganese levels in food samples using flame atomic absorption spectrometry (FAAS). All steps of the cloud point extraction procedure were performed on-line, from the mixing of reagents to detection. The manganese ions are complexed in a mixture of the reagent 2-[2′-(6-methyl-benzothiazolylazo)]-4-bromophenol (Me-BTABr) and Triton X-114. The components are retained on a minicolumn and then desorbed with eluent acid to subsequent detection of manganese by FAAS. Under the optimized conditions, the method presented a detection limit of 0.7 μg L − 1 and an enrichment factor of 17 to a volume of 3000 μL. The sampling frequency was 30 h − 1 . The accuracy of the method was tested by evaluating the amount of Mn in certified reference materials (apple leaves NIST 1515 and spinach leaves NIST 1570a). The proposed procedure was applied to food samples (shrimp powder, flaxseed flour, wheat flour, soy flour and oat), and the results agreed with those obtained by the determination of Mn in foods by atomic absorption spectrometry with electrothermal atomization (ETAAS).

Trace level determination of cadmium in wine by on-line preconcentration in a 5-Br-PADAP functionalized wool-packed microcolumn coupled to flame atomic absorption spectrometry

An on-line retention and preconcentration system based on a sheep wool-packed microcolumn combined with flame atomic absorption spectrometry is proposed for trace level determination of Cd in wine. A chelating reagent 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol was immobilized onto the wool before retention of the analyte. Several factors influencing the preconcentration efficiency of Cd and his subsequent determination, such as pH, eluent type, sample and eluent flow rates, interfering effects, were studied. A preconcentration factor of 39 was obtained with only 20 mL of sample. The relative standard deviation for five determinations of 1 μg L −1 Cd was 3.4%. The calibration graph was linear with a correlation coefficient of 0.998 at levels near the detection limit and up to at least 25 μg L −1. The limit of detection was 37 ng L −1. The accuracy of the proposed methodology was tested by comparison of the results with those obtained by electrothermal atomic absorption spectrometry analysis along with a recovery study. Finally, the method was employed for evaluating Cd levels in different wines including, blank, rose, and red.

Factorial design for multivariate optimization of preconcentration system for spectrophotometric phosphorus determination

The present paper proposes a preconcentration procedure for phosphorus determination by using ultraviolet–visible spectrophotometer. It is based on the formation of phosphomolybdate and its reduction to molybdenum blue. Phosphorus extraction as phosphomolybdenum blue complex was performed onto Amberlite XAD-4. The optimization step was carried out using two-level full factorial design. Three variables (resin amount, sample volume, flow rate) were regarded as factors in the optimization. The relative standard deviation was 2% at 0.08 μg mL −1. The limit of detection was found to be 2.23 μg L −1 ( N = 15). The proposed solid-phase extraction procedure was applied to phosphorus in some fruit leaves, natural waters, and a standard reference material (SRM 1515 apple leaves).

Determination of cadmium at ultra-trace levels by CPE–molecular fluorescence combined methodology

A highly sensitive micelle-mediated extraction methodology for the preconcentration and determination of trace levels of cadmium by molecular fluorescence has been developed. Metal was complexed with o-phenanthroline ( o-phen) and eosin (eo) at pH 7.6 in buffer Tris medium and quantitatively extracted into a small volume of surfactant-rich phase of PONPE 7.5 after centrifugating. The chemical variables affecting cloud point extraction (CPE) were evaluated and optimized. The RSD for six replicates of cadmium determinations at 0.84 μg L −1 level was 1.17%. The linearity range using the preconcentration system was between 2.79 × 10 −3 μg L −1 and 2.81 μg L −1 with a correlation coefficient of 0.99. Under the optimal conditions, it obtained a LOD of 8.38 × 10 −4 μg L −1 and LOQ of 2.79 × 10 −3 μg L −1. The method presented good sensitivity and selectivity and was applied to the determination of trace amounts of cadmium in commercially bottled mineral water, tap water and water well samples with satisfactory results. The proposed method is an innovative application of CPE-luminescence to metal analysis comparable in sensitivity and accuracy with atomic spectroscopies.

Simple micro-column with multi-walled carbon nanotubes for on-line preconcentration and determination of lead in natural water by hydride generation atomic fluorescence spectrometry

A flow injection on-line preconcentration system was developed for the determination of lead by hydride generation atomic fluorescence spectrometry (HG-AFS). It is based on a simple micro-column filled with multiwalled carbon nanotubes (MWCNTs). The preconcentration of lead on the MWCNTs was carried out based on the adsorptive retention of analyte via on-line introducing the sample into the micro-column system. A 0.3 mol L−1 HNO3 was introduced to elute the retained analyte and merged with KBH4 solution for HG-AFS detection. Under the optimal experimental conditions, an enhancement factor of 26 was obtained with a sample consumption of 14.4 mL. The limit of detection was 2.8 ng L−1 and the precision (RSD) of 11 replicate measurements of 0.2 μg L−1 Pb was 4.4%. The method was validated by analyzing three certified reference materials, and was successfully applied to the determination of trace lead in natural water samples.

Use of clinoptilolite loaded with 1-(2-pyridylazo)-2-naphthol as a sorbent for preconcentration of Pb(II), Ni(II), Cd(II) and Cu(II) prior to their determination by flame atomic absorption spectroscopy

A solid phase extraction system for separation and preconcentration of trace amounts of Pb(II), Ni(II), Cd(II) and Cu(II) is proposed. The procedure is based on the adsorption of Pb2+, Ni2+, Cd2+ and Cu2+ ions on a column of 1-(2-pyridylazo)-2-naphthol (PAN) immobilised on surfactant-coated clinoptilolite prior to their determinations by Flame Atomic Absorption Spectroscopy (FAAS). The effective parameters including pH, sample volume, sample flow rate and eluent flow rate were also studied. The analytes collected on the column were eluted with 5 mL of 1 mol L−1 nitric acid. A concentration factor of 180 can be achieved by passing 900 mL of sample through the column. The detection limits (3 s) for Cd, Cu, Pb and Ni were found to be 0.28, 0.12, 0.44 and 0.46 µg L−1, respectively. The relative SDs at 10 µg L−1 (n = 10) for analytes were in the range of 1.2–1.4%. The method was applied to the determination of Pb, Ni, Cd and Cu in water samples.

Speciation of chromium in river water samples contaminated with leather effluents by flame atomic absorption spectrometry after separation/preconcentration by cloud point extraction

In the present work, a cloud point extraction (CPE) system has been proposed for determination of species de chromium in the natural water samples, Cr(III) and Cr(VI). The procedure was based on the reaction of Cr(III) with 1-(2-pyridilazo)-2-naphtol (PAN) in a surfactant solution (Triton X-114) yielding a hydrophobic complex, which then is entrapped “in situ” in the surfactant micelles. When the temperature of the system was higher than the cloud point of Triton X-114, the complex of Cr(III)-PAN entered the surfactant-rich phase and thus separation of the analyte from the matrix was achieved. Separation of the two phases was accomplished by centrifugation for 15 min at 2500 rpm. The Cr(VI) assay is based on its reduction to Cr(III) by ascorbic acid which subsequently reacts with PAN in a similar manner. The main factors affecting the cloud point extraction, such as complexation pH (7.7), buffer concentration (0.025 mol L − 1 ) and microwave irradiation time (10 min) were optimized by response surface methodology (RSM) using Box–Behnken design. Under the optimized conditions, the preconcentration system (50 mL sample) permitted an enrichment factor of 48, linear range of 2.5–80 μg L − 1 , limit of detection and quantification of 0.7 and 2.5 μg L − 1 , respectively, and the relative standard deviation ( n = 10) of 2.0% for 50 μg L − 1 Cr(III) solution and ( n = 10) 5.5% for 10 μg L − 1 . The proposed procedure was applied to the speciation of chromium in river water samples. The procedure affords recoveries of 84–115% and a relative standard deviation lower than 4.2%. The analytical results of total chromium in the river water samples under study agreed well with those by electrothermal atomic absorption spectrometry (ET AAS). It is proved that the procedure can be successfully employed as an alternative to the commonly used preconcentration and speciation analytical techniques.

An automated preconcentration system for the determination of manganese in food samples

In this work, an on-line automated system for the preconcentration and evaluation of manganese in food samples is proposed. The preconcentration of manganese ions is carried out using two mini-columns packed with 4-(5′-bromo-2′-thiazolylazo)orcinol (Br-TAO) loaded polyurethane foam. After a preconcentration step, a stream of hydrochloric acid is passed through the mini-column in order to transport the manganese directly to the flame atomic absorption spectrometer. The sample frequency was 60 h −1 for a 60 s preconcentration time. The limit of detection and enrichment factor were 0.70 μg L −1 and 17, respectively. The accuracy of the procedure was evaluated by analysis of biological reference materials (spinach leaves, tomato leaves and pine needles). The procedure was successfully applied for the evaluation of manganese in several food samples, such as corn, rice and cassava flour.

On-line solid phase extraction system using 1,10-phenanthroline immobilized on surfactant coated alumina for the flame atomic absorption spectrometric determination of copper and cadmium

An on-line solid phase extraction (SPE) preconcentration system coupled to flame atomic absorption spectrometer (FAAS) was developed for determination of copper and cadmium at μg L −1 level. The method is based on the on-line retention of copper and cadmium on a microcolumn of alumina modified with sodium dodecyl sulfate (SDS) and 1,10-phenanthroline and subsequent elution with ethanol and determination by FAAS. The effect of chemical and flow variables that could affect the performance of the system was investigated. The relative standard deviation ( n = 6) at 20 μg L −1 level for copper and cadmium were 1.4 and 2.2% and the corresponding limits of detection (based on 3σ) were 0.04 and 0.14 μg L −1, respectively. The method was successfully applied to determination of copper and cadmium in human hair and water samples.

Determination of REEs in seawater by ICP-MS after on-line preconcentration using a syringe-driven chelating column

A syringe-driven chelating column (SDCC) was applied to develop an on-line preconcentration/inductively coupled plasma mass spectrometry (ICP-MS) method for preconcentration and determination of rare earth elements (REEs) in seawater samples. The present on-line preconcentration system consists of only one pump, two valves, an SDCC, an ICP-MS, several connectors, and Teflon tubes. Optimizations of adsorption pH condition, sample loading flow rate, and integration range were carried out to achieve optimum measurement conditions for REEs in seawater sample. Six minutes was enough for a preconcentration and measurement cycle using 10 mL of seawater sample, where the detection limits for different REEs were in the range of 0.005 pg mL −1 to 0.09 pg mL −1. Analytical results of REEs in a seawater certified reference material (CRM), NASS-5, confirmed the usefulness of the present method. Furthermore, concentrations of REEs in Nikkawa Beach coastal seawater were determined and discussed with shale normalized REE distribution pattern.

On-line ionic liquid-based preconcentration system coupled to flame atomic absorption spectrometry for trace cadmium determination in plastic food packaging materials

A novel on-line preconcentration method based on liquid–liquid (L–L) extraction with room temperature ionic liquids (RTILs) coupled to flame atomic absorption spectrometry (FAAS) was developed for cadmium determination in plastic food packaging materials. The methodology is based on the complexation of Cd with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) reagent after sample digestion followed by extraction of the complex with the RTIL 1-butyl-3-methylimidazolium hexafluorophosphate ([C 4mim][PF 6]). The mixture was loaded into a flow injection analysis (FIA) manifold and the RTIL rich-phase was retained in a microcolumn filled with silica gel. The RTIL rich-phase was then eluted directly into FAAS. A enhancement factor of 35 was achieved with 20 mL of sample. The limit of detection (LOD), obtained as IUPAC recommendation, was 6 ng g −1 and the relative standard deviation (R.S.D.) for 10 replicates at 10 μg L −1 Cd concentration level was 3.9%, calculated at the peak heights. The calibration graph was linear and a correlation coefficient of 0.9998 was achieved. The accuracy of the method was evaluated by both a recovery study and comparison of results with direct determination by electrothermal atomic absorption spectrometry (ETAAS). The method was successfully applied for Cd determination in plastic food packaging materials and Cd concentrations found were in the range of 0.04–10.4 μg g −1.

On-line preconcentration system using a microcolumn packed with Alizarin Red S-modified alumina for zinc determination by flame atomic absorption spectrometry

A simple and sensitive on-line flow injection system for determination of zinc with FAAS has been described. The method is based on the separation and preconcentration of zinc on a microcolumn of immobilized Alizarin Red S on alumina. The adsorbed analyte is then eluted with 250 µL of nitric acid (1 mol L-1) and is transported to flame atomic absorption spectrometer for quantification. The effect of pH, sample and eluent flow rates and presence of various cations and anions on the retention of zinc was investigated. The sorption of zinc was quantitative in the pH range of 5.5-8.5. For a sample volume of 25 mL an enrichment factor of 144 and a detection limit (3S) of 0.2 µg L-1 was obtained. The precision (RSD, n=7) was 3.0% at the 20 µg L-1 level. The developed system was successfully applied to the determination of zinc in water samples, hair, urine and saliva.

Trace Lead Measurement andOnlineRemoval of Matrix Interference in Geosamples by Ion‐Exchange Coupled with Flow Injection and Hydride Generation Atomic FluorescenceSpectrometry

A flow injection method has been developed for the direct determination of free available Pb(II). The method is based on the chemical sorption of Pb(II), from pH7 solutions, on a column packed of chelating resin. The retained complex was afterwards eluted with hydrochloric acid followed by hydride generation with reduction by tetrahydroborate. The preconcentration system proposed in this paper allows the elimination of great part of the saline content in the sample. A thorough scrutiny was made for chemical variables and FI parameters. With a sampling volume of 10.5 mL, quantitative retention of Pb (II) was obtained, along with an enrichment factor of 40 and a sampling frequency of 15 h−1. The detection limit, defined as 3 times the blank standard deviation (3σ), was 0.0031 ngml−1. The precision was characterized by an RSD value of 3.78% (at the 4 ng·ml−1 level, n = 11). The developed method has been applied to the determination of trace Pb in three standard reference materials. Accuracy was assessed through comparing the results with the accepted values.

Development of a flow system for the determination of cadmium in fuel alcohol using vermicompost as biosorbent and flame atomic absorption spectrometry

In this study a method for the determination of cadmium in fuel alcohol using solid-phase extraction with a flow injection analysis system and detection by flame atomic absorption spectrometry was developed. The sorbent material used was a vermicompost commonly used as a garden fertilizer. The chemical and flow variables of the on-line preconcentration system were optimized by means of a full factorial design. The selected factors were: sorbent mass, sample pH, buffer concentration and sample flow rate. The optimum extraction conditions were obtained using sample pH in the range of 7.3–8.3 buffered with tris(hydroxymethyl)aminomethane at 50 mmol L −1, a sample flow rate of 4.5 mL min −1 and 160 mg of sorbent mass. With the optimized conditions, the preconcentration factor, limit of detection and sample throughput were estimated as 32 (for preconcentration of 10 mL sample), 1.7 μg L −1 and 20 samples per hour, respectively. The analytical curve was linear from 5 up to at least 50 μg L −1, with a correlation coefficient of 0.998 and a relative standard deviation of 2.4% (35 μg L −1, n = 7). The developed method was successfully applied to spiked fuel alcohol, and accuracy was assessed through recovery tests, with recovery ranging from 94% to 100%.

Determination of trace heavy metals in soil and sediments by atomic spectrometry following preconcentration with Schiff bases on Amberlite XAD-4

A matrix separation and analyte preconcentration system using Amberlite XAD copolymer resins functionalized by Schiff base reactions coupled with atomic spectrometry has been developed. Three different functionalized Amberlite XAD resins were synthesized using 4-phenylthiosemicarbazide, 2,3-dihydroxybenzaldehyde and 2-thiophenecarboxaldehyde as reagents. These resins could be used to preconcentrate transition and other trace heavy metal analytes from nitric acid digests of soil and sediment samples. Analyte retention was shown to work well at pH 6.0. After treatment of the digests with sodium fluoride and buffering to pH 6, samples that contain extremely large concentrations of iron were analysed for trace analytes without the excess iron overloading the capacity of the resin. The analytes Cd, Co, Cu, Ni and Pb were preconcentrated from acid extracts of certified soil/sediment samples and then eluted with 0.1 M HNO 3 directly to the detection system. Flame atomic absorption spectrometry was used as a means of detection during the studies. The efficiency of the chelating resin and the accuracy of the proposed method were evaluated by the analysis of soil (SO-2) and sediment (LGC 6157 and MESS-3) certified reference materials.

Adsorption behaviour of cadmium on L-methionine immobilized on controlled pore glass

The adsorption behaviour of Cd onto the relative non-polar L-methionine was studied. To this end, L-met was immobilized on controlled pore glass (CPG), incorporated in a microcolumn and inserted in a flow injection system for Cd preconcentration from aqueous solutions. Binding constant of the system was calculated and it turned to be of 1.99, with sites capacity of n = 3.12. The ratio of Cd moles bound to L-met moles was calculated and it was 0.03:1 at pH 9.0. On-line breakthrough curves were used to study the effect of pH, analyte concentration and influent flow rate on Cd retention. A complementary pH study was added with a titration curve. Transient peak areas revealed that Cd stripping from the column occurred instantaneously. The system achieves an enrichment factor of 130, reaching a detection limit of 0.63 ng L − 1 when 10 mL of the solution were passed through the column. The method was successfully applied to Cd determination in the standard reference material (SRM), QC METAL LL2 metals in natural water, as a validation study.

Hybrid mesoporous materials for on-line preconcentration of Cr(VI) followed by one-step scheme for elution and colorimetric determination at ultratrace levels

An hybrid mesoporous material synthesised in our laboratories for solid phase extraction (SPE) in flow through systems has been used for analytical purposes. The solid was obtained from mesoporous silica MCM-41 functionalized with 3-aminopropyltriethoxy silane by Sol–Gel methodology. In order to exploit the large sorption capacity of the material together with the possibility of modeling it for anions retention, a microcolumn (MC) filled with the solid was inserted in a flow system for preconcentration of Cr(VI) and its determination at ultratrace levels in natural waters. The analytical methodology involved a reverse flow injection system (rFI) holding a MC filled with the solid for the analyte extraction. Elution and colorimetric detection were carried out with 1–5 diphenylcarbazide (DPC) in sulfuric acid. DPC produced the reduction of Cr(VI) to Cr(III) together with the generation of a cationic red complex between Cr(III) and 1–5 diphenylcarbazone which was easily eluted and detected with a visible spectrophotometer. Moreover, the filling material got ready for the next sample loading remaining unspoiled for more than 300 cycles. The effect of several variables on the analytical signal as well as the influence of cationic and anionic interferences were discussed. Particular attention was given to sulfuric acid interference since it is the required media for the complex generation. Under optimal conditions, 99.8% of Cr(VI) recovery was obtained for a preconcentration time of 120 s (sample and DPC flow rates = 1 mL min −1) and an elution volume of 250 μL. The limit of detection (3 s) was found to be 0.09 μg L −1 Cr(VI) with a relative standard deviation ( n = 10, 3 μg L −1) of 1.8. Since no Cr(III) was retained by the solid material and Cr(VI) was completely adsorbed, electrothermal atomic absorption spectrometry (ET AAS) determinations of Cr(III) were also performed by simply measuring its concentration at the end of the microcolumn after Cr(VI) retention by the mesoporous solid. Applications to the determination of Cr(VI) and Cr(III) in natural waters and the validation of the methodology were also studied.

Gas chromatography negative ion chemical ionization mass spectrometry: Application to the detection of alkyl nitrates and halocarbons in the atmosphere

Alkyl nitrates and very short-lived halocarbon species are important atmospheric trace gas species that are present in the low to sub parts per trillion concentration range. This presents an analytical challenge for their detection and quantification that requires instrumentation with high sensitivity and selectivity. In this paper, we present a new in situ gas chromatograph negative ion chemical ionization mass spectrometer (GC/NICI–MS) coupled to a non-cryogen sample pre-concentration system. This instrument, with detection limits of <0.01 ppt, is capable of detecting and quantifying a large suite of alkyl nitrate and halocarbon species with high sensitivity and precision. The effects of ion source temperature and reagent gas pressure on the ionization efficiency of the NICI mode are investigated and the results are used to optimize the sensitivity. The NICI mode is compared to the more frequently used electron impact (EI) ionization and the enhancements in sensitivity are presented for all the calibrated compounds.

A preconcentration system for determination of copper and nickel in water and food samples employing flame atomic absorption spectrometry

A separation/preconcentration procedure using solid phase extraction has been proposed for the flame atomic absorption spectrometric determination of copper and nickel at trace level in food samples. The solid phase is Dowex Optipore SD-2 resin contained on a minicolumn, where analyte ions are sorbed as 5-methyl-4-(2-thiazolylazo) resorcinol chelates. After elution using 1 mol L −1 nitric acid solution, the analytes are determinate employing flame atomic absorption spectrometry. The optimization step was performed using a full two-level factorial design and the variables studied were: pH, reagent concentration (RC) and amount of resin on the column (AR). Under the experimental conditions established in the optimization step, the procedure allows the determination of copper and nickel with limit of detection of 1.03 and 1.90 μg L −1, respectively and precision of 7 and 8%, for concentrations of copper and nickel of 200 μg L −1. The effect of matrix ions was also evaluated. The accuracy was confirmed by analyzing of the followings certified reference materials: NIST SRM 1515 Apple leaves and GBW 07603 Aquatic and Terrestrial Biological Products. The developed method was successfully applied for the determination of copper and nickel in real samples including human hair, chicken meat, black tea and canned fish.

Selective determination of total vanadium in water samples by cloud point extraction of its ternary complex

A highly sensitive micelle-mediated extraction methodology for the preconcentration of trace levels of vanadium as a prior step to its determination by flame atomic absorption spectrometry (FAAS) has been developed. Vanadium was complexed with 1-(2-pyridylazo)-2-naphthol (PAN) and hydrogen peroxide in acidic medium (0.2 mol L −1 phosphoric acid) using Triton X-100 as surfactant and quantitatively extracted into a small volume of the surfactant-rich phase after centrifugation. The color reaction of vanadium ions with hydrogen peroxide and PAN in phosphoric acid medium is highly selective. The chemical variables affecting cloud point extraction (CPE) were evaluated and optimized. The R.S.D. for 5 replicate determinations at the 20 μg L −1 V level was 3.6%. The calibration graph using the preconcentration system for vanadium was linear with a correlation coefficient of 0.99 at levels near the detection limits up to at least 0.6 μg L −1. The method has good sensitivity and selectivity and was applied to the determination of trace amounts of vanadium in water samples with satisfactory result. The proposed method is a rare application of CPE-atomic spectrometry to vanadium assay, and is superior to most other similar methods, because its useful pH range is in the moderately acidic range achieved with phosphoric acid. At this pH, many potential interferents are not chelated with PAN, and iron(III) as the major interferent is bound in a stable phosphate complex.