Magnetic System Research Articles

Active Inertia Extended Resonance Ratio Control for Permanent Magnetic Coupling Transmission System

Active Inertia Extended Resonance Ratio Control for Permanent Magnetic Coupling Transmission System

Phase behavior of aqueous two-phase systems formed with cholinium-based magnetic ionic liquids: Experimental insights and theoretical correlations

In this work, three cholinium-based MILs were synthesized, characterized and successfully applied to construct the magnetically responsive aqueous two-phase system (ATPs). This ATPs combined the advantages of ILs and magnetic responsiveness, and showed great potential in the field of extraction and separation. Phase behavior for the magnetic ionic liquid aqueous two-phase systems (MIL-ATPSs) containing [N 1 1n 2OH] [TEMPO-OSO3] + salts + water was investigated experimentally at different temperatures. Merchuk equation was adopted to fit the experimental binodal data with satisfactory correlation performances. The effects of the structure of MILs, temperature and types of salts on the phase behavior were evaluated. Investigation on the phase separation mechanism showed that the phase formation was affected by the structure and viscosity of MILs. The salting-out effect is recognized as the major force for phase separation, which is closely related to the Gibbs free energy of hydration (ΔhydG) and entropy of hydration (ΔhydS) of salts. In addition, a larger biphasic area was obtained by increasing the temperature, indicating the phase separation process was endothermic and entropically driven. The binodal curve at different temperature confirms that this MIL-ATPs has low critical solution temperature (LCST) phase transition behavior. All these experimentally measured data and the theoretical correlations can provide meaningful and valuable information that may promote further research and application.

Heat transfer-deformation characteristics and fracture damage analysis during LN2 freeze-thaw process in different rank coals

Exploring the heat transfer and deformation characteristics of coal bodies of different coal ranks during the freeze-thaw process is of significant importance for analyzing the fracture mechanism under the effect of liquid nitrogen (LN2). This experiment targets lignite, bituminite, and anthracite under both saturated and dry conditions. A real-time temperature-strain monitoring system was employed to observe the heat transfer and deformation characteristics of coal samples with different ranks throughout the freeze-thaw cycle. Additionally, a nuclear magnetic resonance system was utilized to examine the characteristics of pore damage before and after fracturing. The findings reveal: (1) During the freeze-thaw process, the absolute value of the temperature evolution rate for dry coal samples shows a negative correlation with coal rank, indicating a close link between temperature diffusion and intrinsic coal properties like oxygen content and porosity. (2) For saturated coal samples, the absolute value of the temperature change rate during freezing decreases as the coal rank increases, with the opposite trend observed during thawing. The phase change effect of water in fractures during freezing can enhance internal temperature diffusion in the coal body, while it acts as an inhibitor during thawing. (3) Based on the trend of strain fluctuations, the coal body deformation process during the freeze-thaw cycle can be segmented into seven stages, summarizing the general mechanisms of deformation failure. (4) Under saturated conditions, the amplitude of elastic deformation for each sample is negatively correlated with coal rank, with the sequence for dry coal samples being bituminite > anthracite > lignite. (5) The formation of a sealed space at the beginning of freezing is identified as a necessary condition for deformation during the freeze-thaw process, with the formation and strength of the sealed space depending on the temperature diffusion rate, moisture content, and inherent properties of the coal sample.

Influence of electric fields on the magnetic susceptibility of magnetic colloidal systems

Influence of electric fields on the magnetic susceptibility of magnetic colloidal systems

Robotically Adjustable Magnetic Navigation System for Medical Magnetic Milli/Microrobots

Robotically Adjustable Magnetic Navigation System for Medical Magnetic Milli/Microrobots

Effect of apremilast on hand and whole-body MRI assessments of inflammation in patients with psoriatic arthritis (MOSAIC): a phase 4, multicentre, single-arm, open-label study.

The Psoriatic Arthritis Magnetic Resonance Imaging Scoring System (PsAMRIS) and MRI Whole-Body Scoring System for Inflammation in Peripheral Joints and Entheses in Inflammatory Arthritis (MRI-WIPE) have not been used together to assess treatment of psoriatic arthritis in a clinical trial. We aimed to assess the effect of apremilast treatment on inflammation, with outcomes measured by PsAMRIS and MRI-WIPE. MOSAIC was a phase 4, multicentre, single-arm, open-label study conducted at 29 sites across ten countries (Belgium, Canada, Denmark, Germany, Italy, Russia, Spain, Switzerland, the UK, and the USA). Adults aged 18 years or older with a documented diagnosis of psoriatic arthritis for a duration of 3 months to 5 years self-enrolled and were included if they met the classification criteria for active psoriatic arthritis at screening. Patients were required to have at least three swollen and three tender joints with hand involvement and at least one active enthesitis site according to the Spondyloarthritis Research Consortium of Canada enthesitis index or the Leeds enthesitis index. Patients were excluded if they had previous treatment with a biological disease-modifying antirheumatic drug or previous treatment with more than two conventional synthetic disease-modifying antirheumatic drugs. After a 5-day titration period, patients received apremilast 30 mg orally twice per day. Concomitant stable methotrexate up to 25 mg per week was permitted. The primary endpoint was change from baseline to week 24 in a composite inflammation score of bone marrow oedema, synovitis, and tenosynovitis in the hand as assessed by PsAMRIS. The full analysis set and safety population included all enrolled patients who received at least one dose of apremilast. This completed study is registered with ClinicalTrials.gov (NCT03783026). Between Feb 6, 2019, and May 11, 2022, 123 patients were enrolled in the MOSAIC study. Of these 123 patients, 122 (99%) were treated with apremilast and included in the full analysis set and safety population. 67 (55%) of 122 patients were female, 55 (45%) were male, and 116 (95%) were White. 80 (66%) of 122 patients completed 48 weeks of treatment. The least squares mean change from baseline to week 24 in the composite inflammation score of bone marrow oedema, synovitis, and tenosynovitis as assessed by PsAMRIS was -2·32 (95% CI -4·73 to 0·09). 95 (78%) of 122 patients had at least one treatment-emergent adverse event. Six (5%) patients had a severe treatment-emergent adverse event and six (5%) patients had a serious treatment-emergent adverse event. No serious treatment-emergent adverse events were considered to be related to apremilast. Apremilast improved inflammation in joints and entheses on assessment of MRI measures in the hand and the whole body. Our findings encourage the use of MRI, including whole-body MRI, as an objective outcome measure in trials in patients with psoriatic arthritis. Amgen.

Accelerating brain three-dimensional T2 fluid-attenuated inversion recovery using artificial intelligence-assisted compressed sensing: a comparison study with parallel imaging.

Shortening the acquisition time of brain three-dimensional T2 fluid-attenuated inversion recovery (3D T2 FLAIR) by using acceleration techniques has the potential to reduce motion artifacts in images and facilitate clinical application. This study aimed to assess the image quality of brain 3D T2 FLAIR accelerated by artificial intelligence-assisted compressed sensing (ACS) in comparison to 3D T2 FLAIR accelerated by parallel imaging (PI). In this prospective cohort study, 102 consecutive participants, including both healthy individuals and those with suspected brain diseases, were recruited and underwent both ACS- and PI-3D T2 FLAIR scans with a 3.0-Tesla magnetic resonance imaging system from February 2023 to October 2023 in Beijing Tiantan Hospital, Capital Medical University. Quantitative assessment involved white matter (WM) and gray matter (GM) signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR), whole-image sharpness, and tumor volume. Qualitative assessment included the scoring of overall image quality, GM-WM border sharpness, and diagnostic confidence in lesion detection. ACS-3D T2 FLAIR exhibited a shorter acquisition time compared to PI-3D T2 FLAIR (105 vs. 320 seconds). ACS-3D T2 FLAIR, compared to PI-3D T2 FLAIR, demonstrated a significantly higher mean SNRWM (25.922±6.811 vs. 22.544±5.853; P<0.001), SNRGM (18.324±7.137 vs. 17.102±6.659; P=0.049), CNRWM/GM (4.613±1.547 vs. 4.160±1.552; P<0.001), and sharpness (0.413±0.049 vs. 0.396±0.034; P<0.001), while no significant differences were found for the overall image quality ratings (P=0.063) or GM-WM border sharpness ratings (P=0.125). A good agreement on tumor volume was achieved between ACS-3D T2 FLAIR and PI-3D T2 FLAIR images (intraclass correlation coefficient =0.999; 0.998-1.000; P<0.001). Images acquired with ACS demonstrated nearly equivalent diagnostic confidence to those obtained with PI (P>0.05). The ACS technique offers a substantial reduction in scanning time for brain 3D T2 FLAIR compared to PI while maintaining good image quality and equivalent diagnostic confidence.

Investigating the application of graphene quantum dots doped with heteroatoms as a contrast agent in magnetic resonance imaging system

Investigating the application of graphene quantum dots doped with heteroatoms as a contrast agent in magnetic resonance imaging system

Uniform microwave field formation for control of ensembles of negatively charged nitrogen vacancy in diamond.

The homogeneity of the microwave magnetic field is essential in controlling a large volume of ensemble spins, for example, in the case of sensitive magnetometry with nitrogen-vacancy (NV) centers in diamond. This is particularly important for pulsed measurement, where the fidelity of control pulses plays a crucial role in its sensitivity. So far, several magnetic field-forming systems have been proposed, but no detailed comparison has been made. Here, we numerically study the homogeneity of five different systems, including a planar antenna, a dielectric resonator, a cylindrical inductor, a barrel-shaped coil, and a nested barrel-shaped coil. The results of the simulation allowed us to optimize the design parameters of the barrel-shaped field-forming system, which led to significantly improved magnetic field uniformity. To measure this effect, we experimentally compared the homogeneity of a field-forming system having a barrel shape with that of a planar field-forming system by measuring Rabi oscillations of an ensemble of NV centers with them. Significant improvements in inhomogeneity were confirmed in the barrel-shaped coil.

Electric and magnetic waveguides in graphene: quantum and classical

Electric and magnetic waveguides are considered in planar Dirac materials like graphene as well as their classical version for relativistic particles of zero mass and electric charge. We have assumed the displacement symmetry of the system along the y-direction, whose associated constant is k. We have also examined other symmetries relevant to each type of waveguide, magnetic or electric. Waveguides with square profile have been worked out in detail to show up explicitly some of the most interesting features. For example, the classical region of confined motion of the electric case, for a fixed intensity, is bounded between k and −k, while in the magnetic case that region is symmetric in the energy and presents a gap (−k, k). Besides, in the quantum systems we have shown that there are edge states in the magnetic systems but they are missing in electric waveguides. We have also analysed scattering states and resonances which match with bound states for both waveguides. The classical scattering properties are also quite different in both types of waveguides. While the electric system has essentially one type of refraction of the incident electron, the magnetic system is much richer due to the Lorentz force.

Improving the steering performance of microrobots by using a magnetically actuated technique

Mobile microrobots show the significance of potential medical procedures and challenge areas within the human body. An applied electromagnetic field is used as a precise magnetic actuation system for controllable steering mobility, and positioning is used. In this work, an adaptable microrobot is developed with an effective technique to enhance steering. An electromagnetic system is employed to produce an external magnetic field that guides a microrobot to improve its steerability. In particular, a driving system of eight coils creates a magnetic field that actuates the microrobot and enables upward and downward motion. Accordingly, three types of microrobot designs are proposed. Consequently, an efficient variation of steering in terms of deformation angle is achieved. The corresponding performance is determined mathematically in terms of the main system parameters, such as external magnetic field and microrobot geometry. In addition, finite element model is used for comparison and validation. Simulation results show that for a relatively high value of magnet field, namely, 15 mT and 90°, the deformation angles were 36.98° for the first design, 39.11° for the second design, and 34.48° for the third design in upward deformation. By contrast, the downward deformation ranges were –40.42°, –39.46°, and –37.04° for the first, second, and third designs, respectively, at –90° The error between the upward and downward steering of the second design had the lowest value of 0.35° The second design of the microrobots has the least error between the upward and downward deformation ratio at 0.89 %. In comparison, the first design has a 9.3 % error, and the third design has a 7.42 % error, with a relatively high value of magnetic field density (15 mT). Simulations have shown that the proposed second design is suitable for navigating narrow artery branches with the least error ratio and more precise control. This work verifies that the model could accurately control the steering of microrobots.

Research on Spatial Localization Method of Magnetic Nanoparticle Samples Based on Second Harmonic Waves

Existing magnetic tracer detection systems primarily rely on fundamental wave signal acquisition using non-differential sensor configurations. These sensors are highly susceptible to external interference and lack tomographic localization capabilities, hindering their clinical application. To address these limitations, this paper presents a novel method for achieving the deep spatial localization of tracers. The method exploits second harmonic signal detection at non-zero field points. By considering the combined nonlinear characteristics of the coil’s axial spatial magnetic field distribution and the Langevin function, a correlation model linking the signal peak and bias field is established. This model enables the determination of the tracer’s precise spatial location. Building on this framework, a handheld device for localizing magnetic nanoparticle tracers was developed. The device harnesses the second harmonic response generated by coupling an AC excitation field with a DC bias field. Our findings demonstrate that under conditions of reduced coil turns and weak excitation fields, the DC bias field exhibits exclusive dependence on the axial distance of the detection point, independent of particle concentration. This implies that the saturated DC bias field corresponding to the second harmonic signal can be used to determine the magnetic nanoparticle sample detection depth. The experimental results validated the method’s high accuracy, with axial detection distance and concentration reduction errors of only 4.8% and 4.1%, respectively. This research paves the way for handheld probes capable of tomographic tracer detection, offering a novel approach for advancing magnetically sensitive biomedical detection technologies.

Strength degradation characteristics and damage constitutive model of sandstone under freeze-thaw cycles.

Thorough investigation into the laws governing frozen rock damage in high-altitude and cold regions can offer valuable insights for advancing infrastructure construction, ecological environment protection, and sustainable development on the Qinghai-Xizang Plateau. This study combined with the seasonal variation patterns of frozen rocks in the Qinghai-Xizang Plateau, and processed the rock samples using a freeze-thaw interval of -20 °C~20 °C. Uniaxial compression test was conducted based on the MTS816 rock mechanics testing system. The porosity changes of rock samples with different freeze-thaw cycles were analyzed using the MesoMR12-060H-I nuclear magnetic response analysis system. A rock freeze-thaw load coupled damage constitutive model was derived using the Lemaitre equivalent strain theory. Research has shown that during the freezing process, the pore water inside the rock sample is affected by the phase change of water-ice, resulting in frost heave force, which further promotes the expansion of the pore walls and the initiation of new cracks. When melted, pore water migrates towards newly formed micropores, thereby affecting the changes in the pores of rock samples. The increase in porosity at the micro level weakens the mechanical parameters of rocks at the macro level. The segmented freeze-thaw damage constitutive model based on Lemaitre equivalent strain theory can well fit the experimental results involved in this study, as well as the experimental results obtained by other researchers. The compaction stage can partially reflect the changes in sandstone pore structure under freeze-thaw cycles.

Interface/Dipole Polarized Antibiotics-Loaded Fe3O4/PB Nanoparticles for Non-Invasive Therapy of Osteomyelitis Under Medical Microwave Irradiation.

Due to their poor light penetration, photothermal therapy and photodynamic therapy are ineffective in treating deep tissue infections, such as osteomyelitis caused by Staphylococcus aureus (S. aureus). Here, a microwave (MW)-responsive magnetic targeting composite system consisting of ferric oxide (Fe3O4)/Prussian blue (PB) nanoparticles, gentamicin (Gent), and biodegradable poly(lactic-co-glycolic acid) (PLGA) is reported. The PLGA/Fe3O4/PB/Gent complex is used in combination with MW thermal therapy (MTT), MW dynamic therapy (MDT), and chemotherapy (CT) to treat acute osteomyelitis infected with S. aureus-infected. The powerful antibacterial effect of the PLGA/Fe3O4/PB/Gent is determined by the synergistic effects of heat and reactive oxygen species (ROS) generation by the Fe3O4/PB nanoparticles under MW irradiation and the effective release of Gent at the infection site via magnetic targeting. The antibacterial mechanism of the PLGA/Fe3O4/PB/Gent under MW irradiation is analyzed using bacterial transcriptome RNA sequencing. The MW heat and ROS reduce the activity of the protein transporters on the bacterial membrane, along with the transport of various ions and the acceleration of phosphate metabolism, which can lead to increased permeability of the bacterial membrane, damage the ribosome and DNA, and accompany the internal protein efflux of the bacteria, thus effectively killing the bacteria.

Modelling PM dipoles with longitudinal field gradient for SILA facility

Computational models are described which were built for parametric simulations of permanent magnet (PM) dipoles with a longitudinal field gradient. The dipoles will be used as bending magnets in the synchrotron facility SILA, a new project of the National Research Center “Kurchatov Institute”. The dipoles employ a Sm-Co permanent magnet material and pure iron. The need for high magnetic performance and anticipated interference between neighbouring components is a challenge for design and construction of the magnet system. For this reason the magnet designs must rely on precision 3D simulations. The dipoles are described in detail with parameterized models. Parametric simulations are to be applied at all stages of the project till the commissioning to provide realistic prediction of the magnet behaviour.

Aligned colloidal clusters in an alternating rotating magnetic field elucidated by magnetic relaxation

Precise control at the colloidal scale is one of the most promising bottom-up approaches to fabricating new materials and devices with tunable and precisely engineered properties. Magnetically driven colloidal assembly offers great versatility because of the ability to externally tune particle-particle interactions and to construct a host of particle arrangements. However, despite previous efforts to probe the parameter space, global orientational control in conjunction with two-dimensional microstructural control has remained out of reach. Furthermore, the magnetic relaxation time of superparamagnetic beads has been largely overlooked despite being a key feature of the magnetic response. Here, we take advantage of the magnetic relaxation time of superparamagnetic beads in an alternating rotating magnetic field and show how harnessing this feature facilitates the formation of oriented clusters. The orientation of these clusters can be controlled by field parameters. Using experiments, simulations, and theory, we probe a two-particle system (dimer) under this alternating rotating magnetic field and use its dynamics to provide insights into the collective response that forms clusters. We find that the type of field has significant implications for the dipolar interactions between the colloids because of the nonnegligible magnetic relaxation. Moreover, we find that the competing time scales of the magnetic relaxation and the alternating field generate an anisotropic interaction potential that drives cluster alignment. By exploiting the magnetic relaxation time of magnetic systems, we can tailor new types of interparticle interactions, thereby expanding the capabilities of colloidal assembly in engineering unique materials and devices.

Elliptical Halbach magnet and gradient modules for low-field portable magnetic resonance imaging.

This study aims to develop methods to design the complete magnetic system for a truly portable MRI scanner for neurological and musculoskeletal (MSK) applications, optimized for field homogeneity, field of view (FoV), and gradient performance compared to existing low-weight configurations. We explore optimal elliptic-bore Halbach configurations based on discrete arrays of permanent magnets. In this way, we seek to improve the field homogeneity and remove constraints to the extent of the gradient coils typical of Halbach magnets. Specifically, we have optimized a tightly packed distribution of magnetic Nd2Fe14B cubes with differential evolution algorithms and a second array of shimming magnets with interior point and differential evolution methods. We have also designed and constructed an elliptical set of gradient coils that extend over the whole magnet length, maximizing the distance between the lobe centers. These are optimized with a target field method minimizing a cost function that considers also heat dissipation. We have employed the new toolbox to build the main magnet and gradient modules for a portable MRI scanner designed for point-of-care and residential use. The elliptical Halbach bore has semi-axes of 10 and 14& cm, and the magnet generates a field of 87& mT homogeneous down to 5700& ppm (parts per million) in a 20-cm diameter FoV; it weighs 216& kg and has a width of 65& cm and a height of 72& cm. Gradient efficiencies go up to around 0.8& mT/m/A, for a maximum of 12& mT/m within 0.5& ms with 15& A and 15& V amplifier. The distance between lobes is 28& cm, significantly increased with respect to other Halbach-based scanners. Heat dissipation is around 25& W at maximum power, and gradient deviations from linearity are below 20% in a 20-cm sphere. Elliptic-bore Halbach magnets enhance the ergonomicity and field distribution of low-cost portable MRI scanners, while allowing for full-length gradient support to increase the FoV. This geometry can be potentially adapted for a prospective low-cost whole-body technology.

Construction of Chiral-Magnetic-Dielectric Trinity Structures with Different Magnetic Systems for Efficient Low-Frequency Microwave Absorption.

The fabrication of carbon nanocoil (CNC)-based chiral-dielectric-magnetic trinity composites holds great significance in low-frequency microwave absorption fields. However, it is not clear that how the different magnetic systems affect the magnetic and frequency responses of the composites. Herein, four types of magnetic metals, FeCo, CoNi, FeNi, and FeCoNi, are selected to be combined with the chiral templates respectively, resulting in four types of chiral-dielectric-magnetic composites with similar morphology. The CNC templates endow all the composites with excellent dielectric loss. Further permeability analysis and the micro-magnetic simulation confirm that the frequency response region can be well adjusted by changing the magnetic systems with specific magnetic resonance modes and magnetic domain motion. Due to the synergistic effect between magnetism, chirality, and dielectricity, the FeNi-based composites exhibit the best low-frequency microwave absorption performance. The minimum RL of -60.7 dB is achieved at 6.7 GHz with an ultra-low filling ratio of 10%, and the EAB value in low-frequency region is extended to 3.7 GHz. This study provides further guidelines for the design of the chiral-dielectric-magnetic trinity composites in low-frequency microwave absorption.

Robust Controller Development via Iterative Model Updating for Active Magnetic Bearing Rotor Systems

Robust Controller Development via Iterative Model Updating for Active Magnetic Bearing Rotor Systems

A low-cost electronic and optical system for magnetic hyperthermia experimental studies

Magnetic hyperthermia is an alternative to treatments such as chemotherapy and radiotherapy that employs the heat generated by magnetic nanoparticles under the influence of a magnetic field to kill cancer cells while ideally causing no harm to healthy tissues. A low-cost magnetic hyperthermia investigation platform with commercially available and easy-to-assemble parts was presented to provide and expand research in this area for a larger scientific community. The magnetic hyperthermia measurement system consists of three main parts: a designed thermally insulated sample holder, a commercial 88 kHz magnetic induction heater, and a custom-built fiber optic based refractometer as temperature sensor. The system was tested with commercial EFH-1 magnetic fluids. Time dependent temperature changes were measured for applied magnetic fields of 3.5 kA/m, 4.8 kA/m, and 6.0 kA/m. The corresponding specific loss power values were calculated as 0.28 W/g, 0.51 W/g, and 0.79 W/g, respectively. Intrinsic loss power of commercial ferrofluid was determined as 0.25 ± 0.01 nHm2/kg, found to be comparable to the results of specialized commercial magnetic hyperthermia systems. The results show that the system can easily be used for hyperthermia demonstrations for educational purposes as well as in convenient scientific research with proper calibration.