Synchronous Reluctance Motor Research Articles

Disturbance-Observer-Based Sliding-Mode Speed Control for Synchronous Reluctance Motor Drives via Generalized Super-Twisting Algorithm

In this study, a novel composite speed controller combining a sliding-mode speed controller with a disturbance observer is proposed for the vector-controlled synchronous reluctance motor (SynRM) drive system. The proposed composite speed controller employs the generalized super-twisting sliding-mode (GSTSM) algorithm to construct both the speed controller and the disturbance observer. The GSTSM speed controller is utilized to stabilize the speed tracking error dynamics in finite time, while the GSTSM disturbance observer compensates for the total disturbance in the speed tracking error dynamics, which includes external disturbances and parametric uncertainties. Under the framework of the constant direct-axis current component vector control strategy for the SynRM drive system, comparative simulation studies are conducted among the standard STSM speed controller, the GSTSM speed controller, the composite speed controller using a GSTSM speed controller and a standard STSM disturbance observer, and the proposed composite speed controller. The effectiveness and superiority of the proposed composite speed controller are verified through simulation results.

Dynamic modeling and identification of a reluctance synchronous machine parameters

This article discusses an identification and modeling approach of a reluctance synchronous motor (RSM) based on the running rotor technique. The applied flux linkage approximation functions reflect the self-saturation and cross-saturation effects, and the applied mathematical model is continuous and differentiable. The proper design of the experiment is discussed, and relevant recommendations are made to ensure the mitigation of procedural mistakes in the experiments. A detailed analysis of the impact of configuration faults on the obtained experimental data is provided, considering distortions in the obtained flux linkage and inductance surfaces. Considering the achieved model accuracy, a novel model evaluation considering the achieved model accuracy technique based on transient current response is proposed.

Design and Multi-Objective Optimization for Improving Torque Performance of a Permanent Magnet-Assisted Synchronous Reluctance Motor

Permanent magnet-assisted synchronous reluctance motors (PMA-SynRMs) are widely used in various industries as a relatively inexpensive and high-performance energy conversion device. The model proposed in this article relies on a magnetic pole-biased permanent magnet synchronous reluctance motor with a magnetic focusing effect. Two types of models with Halbach array and magnetic focusing effect have been proposed, which increase excitation and make the internal magnetic circuit of the rotor more saturated, thereby achieving higher electromagnetic torque. Through finite element simulation analysis and verification, the motor characteristics of the basic and proposed permanent magnet-assisted synchronous reluctance motor were calculated, including the air gap flux density and back electromotive force (EMF) in no-load analysis, as well as the average torque, torque ripple, and efficiency in load analysis. In addition, multi-objective optimization was also conducted on the rotor topology structure of proposed model two, using the uniform Latin hypercube sampling method to uniformly sample the data samples and the Pearson correlation coefficients to perform a sensitivity analysis on the data. The pilOPT multi-objective autonomous optimization algorithm was used to perform multi-objective autonomous optimization on parameters with high correlation, and the best-found solution based on the Pareto front was selected. Compared with proposed model two, the average torque of the optimized model increased by 18.14%, the efficiency increased by 1.05% and the torque ripple decreased by 5.22%. Finally, the anti-demagnetization performance of the optimized model’s permanent magnet was analyzed.

Maximum Torque Control of Permanent Magnet-Assisted Synchronous Reluctance Motor Using Fuzzy PI

Abstract This paper proposes a fuzzy PI-based Maximum Torque Per Ampere (MTPA) control for Permanent Magnet-Assisted Synchronous Reluctance Motor (PMASynRM). The aim is to address issues such as overshooting and slow response in the operation of the PMASynRM by optimizing MTPA control under traditional PI using a fuzzy PI control algorithm. This approach enhances the system’s responsiveness and disturbance rejection capabilities. The article builds a simulation model for the maximum torque-to-current ratio control of PMASynRM using fuzzy PI control in MATLAB/Simulink, comparing it with traditional PI control. Simulation results indicate that the fuzzy PI motor control system exhibits lower overshoot, faster response speed, and better robustness compared to traditional PI control.

Optimal control of maximum torque current ratio for synchronous reluctance motor based on virtual signal injection algorithm

This study focuses on the maximum torque current ratio control of synchronous reluctance motors and proposes an optimized control method for the maximum torque current ratio of synchronous reluctance motors based on virtual signal injection. Firstly, the research on the maximum torque current ratio control of synchronous reluctance motors based on the virtual signal injection method is conducted, and the existing virtual unipolar square wave signal injection method is analyzed and studied. Secondly, a non-parametric maximum torque current ratio control strategy based on a synchronous reluctance motor combined with the virtual signal injection method is proposed. This strategy does not involve complex parameter calculations, and the control accuracy is not limited by the accuracy of the parameters in the model. The experimental results showed that under the control of virtual bipolar and unipolar square wave signal injection methods, the load torque was converted from 2 Nm to 6 Nm at t = 2:5 s, and there was a significant change in the current amplitude and waveform of the current vector. Under the control of the bipolar injection method, the current amplitude waveform of the motor was lower than that of the unipolar waveform, and the current was smaller. After the load suddenly changed, it could enter a stable state faster. After the load changed at t = 2:5 s, the phase angle of the current vector was quickly adjusted and stabilized under the control of the bipolar signal. The designed method has a good optimization effect compared to the traditional virtual signal injection method, and can achieve high-performance maximum torque current ratio optimization control on synchronous reluctance motors.

Research on Displacement Sensorless Control for Bearingless Synchronous Reluctance Motor Based on the Whale Optimization Algorithm–Elman Neural Network

The unique structure of bearingless motors requires extra displacement sensors to monitor rotor movement, unlike conventional synchronous motors. However, this requirement inevitably escalates the cost and size of the motor. To address these issues, this paper proposes a novel approach: a bearingless synchronous reluctance motor (BSRM) without displacement sensors, utilizing the whale optimization algorithm–Elman neural network (WOA-ENN). The paper firstly introduces the suspension mechanism and mathematical model of the BSRM, upon which a function containing rotor position information is constructed. Subsequently, a sensorless method based on Elman neural network (ENN) is proposed, optimized using the whale optimization algorithm (WOA). Finally, the feasibility and reliability of the proposed approach are validated through simulations and experiments.

Finite Control Set Model Predictive Current Control for Reluctance Synchronous Motor - Current Ripple Analysis

Finite Control Set Model Predictive Current Control for Reluctance Synchronous Motor - Current Ripple Analysis

Development and Analysis of Six-Phase Synchronous Reluctance Motor for Increased Fault Tolerance Capabilities

This paper contains research on the development of a fault-tolerant six-phase synchronous reluctance motor (SynRM) based on the stator adopted from a general-purpose three-phase induction motor. In the design and calculation process, an extended Clarke transformation was developed for a six-phase asymmetrical system. To verify the proposed design approach, a field–circuit model of electromagnetic phenomena in the studied motor was developed and used to study the motor performance. The increased torque value and reduction in torque ripples were confirmed by comparison to the classical three-phase SynRM design. To illustrate fault tolerance capabilities, the operation of the studied three- and six-phase synchronous reluctance motors under inverter-fault conditions was examined. The conducted analysis shows, among other things, that from the electromagnetic performance point of view, only the proposed six-phase machine is able to properly operate under inverter-fault conditions. The results of the winding design calculations, the performed simulations of six-phase motor operation, and the preliminary tests of the prototype motor are presented and discussed.

Control of Grid Synchronized Photovoltaic Fed Synchronous Reluctance Motor Drive for Water Pumping

Control of Grid Synchronized Photovoltaic Fed Synchronous Reluctance Motor Drive for Water Pumping

Dead-Time Compensation Using ADALINE for Reduced-Order Observer-Based Sensorless SynRM Drives

The inverter dead time effect is non-negligible for the control performance of sensorless synchronous reluctance motor (SynRM) drives at low speeds. In this paper, a reduced-order observer-based sensorless control method for SynRM drives combined with the adaptive linear neurons (ADALINE)-based dead-time compensation is proposed. The reduced-order observer-based sensorless control method is presented, for which is parameter tuning is easy. On this basis, the dead-time compensation strategy using ADALINE filters is proposed to reduce the voltage harmonics effect on the estimation performance of the reduced-order observer. With ADALINE filters, the sixth current harmonic can be successfully filtered out by compensating the voltage directly or fitting the current to compensate the voltage. In this way, the low-speed estimation performance of the reduced-order observer is improved. The effectiveness of the proposed method is verified on a 3 kW SynRM experimental platform.

Effect of stator winding chording on the performance of five phase synchronous reluctance motor

The effect of winding chording on five-phase synchronous reluctance motor (SRM) modelled in phase variables is presented. The stator winding configuration is shifted a pole pitch from a full-pitch configuration to a 54 degrees over-full-pitched configuration incorporating the effect of 3rd harmonic of the air-gap magneto-motive force in the inductance equations. The models are monitored on starting, synchronism, loading, faults and loss of synchronism. These are considered simultaneously with vector potential, rotor speed, air-gap flux linkage and winding current. The phase variable (analytical) models have been simulated by using MATLAB/Simulink software while ANSYS Maxwell software has been used to simulate the finite element model (FEM) of the motor for corresponding chording ranges for comparison on direct online starting (DOL). Under all conditions considered in the work, the detailed results are presented and very close similarity is observed between the analytical and the nearly ideal FEM model for all chording ranges and the similarity is enhanced with increase in chording angle.

Design and Performance Analysis of an Outer-Rotor PMaSynRM

Permanent magnet synchronous motors (PMSMs) are consciously used as traction motors in electric vehicles (EVs) and hybrid electric vehicles (HEVs). The rotor position (inner-rotor, outer-rotor) and topology of PMSMs significantly impact their torque profile, efficiency, and demagnetization characteristics. This article focuses on designing an outer-rotor permanent-magnet-assisted synchronous reluctance motor (PMaSynRM) under traction motor requirements and investigating its electromagnetic performance using the finite element method (FEM). This study's primary challenge is achieving optimal machine performance, considering high maximum torque and the risk of demagnetization at low levels. The design, derived from analytical calculations, was subjected to Finite Element Method (FEM) analyses. These analyses investigated motor performance in terms of efficiency, the ability to generate torque at different drive currents, and the risk of demagnetization. As a result of the study, the proposed PMaSynRM design was obtained that provides an adequate demagnetization performance even under 300% loading, has a maximum torque exceeding 35 Nm, and achieves an efficiency of 90% at rated conditions.

Fuzzy Logic Based DTC Control of Synchronous Reluctance Motor

Fuzzy Logic Based DTC Control of Synchronous Reluctance Motor

Finite element analysis and experimental validation of loss reduction strategies in synchronous reluctance motors with combined star delta winding

Finite element analysis and experimental validation of loss reduction strategies in synchronous reluctance motors with combined star delta winding

Analysis of dynamic electromagnetic stress in synchronous reluctance motor accounting for rotor eccentric

Analysis of dynamic electromagnetic stress in synchronous reluctance motor accounting for rotor eccentric

Predictive controllers for synchronous reluctance motor drive systems

This paper proposes the design and implementation of predictive controllers for synchronous reluctance motor drive systems to enhance their dynamic responses. The predictive speed and current controllers in this paper are designed in systematic procedures. The predictive speed controller is implemented by using Laguerre function procedure. The Laguerre function is used to simplify the algorithm and to minimize the execution time of the digital signal processor. For predictive current controller, a finite control set method improves the current tracking ability. The measured currents are used to predict the future phase-current based on the motor model. The optimal control inputs of both predictive controllers are determined by using a cost function minimization method. Experimental results show the proposed drive system provides a wide adjustable speed range, from 2 r/min to 1800 r/min. It has better performance than a proportional-integral (PI) controller including fast rise time, which is 0.9 second, small steady state error, which is 0.32 r/min, and small current ripples. A 32-bit floating-point digital signal processor, TMS-320-F-28335 DSP, is employed to implement the control algorithms.

A Convenient Analytical Model for Predicting Direct-on-Line Synchronous Reluctance Motor Operations at Different Environments

A Convenient Analytical Model for Predicting Direct-on-Line Synchronous Reluctance Motor Operations at Different Environments

Design and Prototyping of a Novel Line-Start Permanent Magnet Assisted Synchronous Reluctance Motor for Fan Application

Design and Prototyping of a Novel Line-Start Permanent Magnet Assisted Synchronous Reluctance Motor for Fan Application

PV Array Fed Synchronous Reluctance Motor Driven Water Pumping System with Grid Integration and Seamless Operability

PV Array Fed Synchronous Reluctance Motor Driven Water Pumping System with Grid Integration and Seamless Operability

Fault-Tolerant Control of a Triple Redundant PMA-SynRM for Minimum Torque Ripple

In this paper, a new fault-tolerant control (FTC) strategy based on minimum torque ripple is proposed for a triple redundant permanent magnet assisted synchronous reluctance motor under single-phase and double-phase faults. Different from removing the faulty modules (single six-phase (S6) operation or single three-phase (S3) operation), the proposed strategy makes full use of the healthy phase of the faulty modules. By precisely controlling the <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">d-q</i> axes currents of each module, the ripple of permanent magnet torque and reluctance torque can be suppressed simultaneously, thus achieving the minimum output torque ripple. Moreover, the ratio ( <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">k</i> ) of the <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">d-q</i> axes current to the stator current can be determined under the constraint of minimum copper loss. In addition, by changing the ratio <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">k</i> , the proposed strategy can be combined with S6 or S3 strategy to achieve the minimum copper loss in a wide torque range. In summary, the proposed FTC strategy not only achieves the minimum torque ripple but also ensures the minimum copper loss. Finally, experiments are carried out to verify the accuracy and validity of the theory.