Switchgrass Biochar Research Articles

Effects of pyrolysis temperature and feedstock type on biochar characteristics pertinent to soil carbon and soil health: A meta‐analysis

AbstractBiochar amendment to soil is utilized globally as an approach to enhance carbon storage and to improve soil functioning. However, biochar characteristics and related improvements of soil functioning depend on biochar production conditions. Systematic evaluation of corresponding biochar characteristics is needed for more targeted and efficient biochar application strategies. Herein, we systematically review the effects of biochar pyrolysis temperature (175–950°C) and feedstock (corn stover, switchgrass and wood) on selected biochar characteristics (carbon content, H/C ratio, nitrogen content, pH, specific surface area, ash content and pore volume). These specific characteristics were selected as being pertinent to soil organic carbon sequestration and soil health improvement. Despite numerous studies on these topics, few have numerically quantified the effects of pyrolysis temperature. Our results show that high pyrolysis temperature (>500°C) increased carbon content and pore volume for wood biochar compared with low pyrolysis temperature (≤500°C). The high pyrolysis temperature decreased the H/C ratio and nitrogen content but increased pH, specific surface area and ash content regardless of feedstock. Compared with corn stover biochar and switchgrass biochar, wood biochar had higher carbon content and larger specific surface area but lower nitrogen and ash contents regardless of pyrolysis temperature. The higher biochar carbon content might be derived from higher lignin and cellulose contents of wood feedstock. Wood feedstock had 76%–109% more lignin and 27%–47% more cellulose than corn stover and switchgrass. Corn stover biochar had higher pH, and switchgrass biochar had larger pore volume than wood biochar. Our study indicates that the targeted production of biochar with specific characteristics can be facilitated by the selection of pyrolysis temperature and feedstock type. For amending soil with biochar, more operationally defined biochar production conditions and feedstock selection might be a way forward to wider acceptance and better predictability of biochar performance under field conditions.

Waste utilization and biodiesel production from Desmodesmus maximus grown in swine wastewater using waste eggshells as a catalyst

Desmodesmus maximus is a potential candidate for algal biofuel production. It was cultivated for lipid enhancement in four different types of wastewater used as algal growth media. After growing Desmodesmus maximus for period of 10 days in four different types of waste water, it was found that swine wastewater collected from Swine Research Center of Oklahoma state university was the best media because of the faster biomass yield and lipid content in the algal biomass. The specific growth rate of algal strain grown in swine waste water was found to be 0.88 µ/d with doubling time T2 of 1.3 h which shows the better quantity of algal biomass. Algal lipids comprised 72.3 % (dry weight %) of the biomass. In our study wastewater was used as a nutrient source for biofuel production while remediating the waste. Calcined waste eggshells doped with lanthanum and switchgrass biochar were used to catalyze the conversion of algal lipid to biodiesel. Our study found that Biochar doped 950 degree Celsius CaO provided the optimal catalyst. The physicochemical characteristics of wastewater were analyzed and it was found that swine wastewater contains all the vital macro and micronutrients required for the optimal growth of this microalgae. The catalyst synthesized from waste eggshells was characterized by FTIR-ATR, SEM-EDX techniques and N2 physisorption by Brunauer–Emmett–Teller (BET) theory. The resulting produced biodiesel was analyzed by 1H NMR, 13C NMR, GC-MS techniques. Conversion to biodiesel was 99 % efficient with the optimized catalyst. The catalyst was subjected to 10 runs of transesterification to study reusability. After 10 runs the reused catalyst still provided 77 % conversion efficiency. The result obtained shows that Desmodesmus maximus grown in swine wastewater yields a very good quality and quantity of biodiesel. The waste eggshells and switchgrass can be utilized as renewable heterogeneous catalysts because of their highly porous nature and a more specific surface area that acts as a catalyst in the transesterification reaction of biodiesel.

Growth Response, Mineral Nutrition, and Water Utilization of Container-grown Woody Ornamentals Grown in Biochar-amended Pine Bark

Container-grown nursery crops generally require daily irrigation applications and potentially more frequent applications during the hottest part of the growing season. Developing management practices that make more efficient use of irrigation water is important for improving the sustainability of nursery crop production. Biochar, a byproduct of pyrolysis, can potentially increase the water-holding capacity and reduce water and nutrient leaching. In addition, the development of sensor-based irrigation technologies has made monitoring substrate moisture a practical tool for irrigation management in the nursery industry. The objective of this research was to determine the effect of switchgrass biochar on water and nutrient-holding capacity and release in container substrates of Buxus sempervirens L. × Buxus microphylla (‘Green Velvet’ boxwood) and Hydrangea paniculata (Pinky Winky® hardy hydrangea). Containers were filled with pine bark and amended with 0%, 10%, or 25% volume of biochar. Plants were irrigated when the volumetric water content (VWC) reached the water-buffering capacity set point of 0.25 cm3·cm−3. The sensor-based irrigation in combination with the low cost biochar substrate amendment increased substrate water-holding capacity and reduced irrigation requirements for the production of hydrangea, a high water use plant. Biochar application rate influenced irrigation frequency, which likely affected plant biomass for hydrangea, but boxwood dry weight was unaffected by biochar rate. Total irrigation applied was decreased by 32% in 10% biochar treatment without reducing hydrangea dry weight. However, in the 25% biochar treatment, total irrigation applied was reduced by 72%, whereas dry weight decreased by 50%. Biochar application reduced leaching volume and leaching fraction in both plants. Leachate analysis over the course of the 8-week experiment showed that the average mass of phosphate (PO4), potassium (K), and total carbon was greater in the leachate from containers that received 25% biochar compared with those receiving 0% or 10% biochar for both plant species. For hydrangea, mass of total nitrogen (TN) and nitrate (NO3) in leachate was not significantly affected by increasing the biochar rate. However, for boxwood, the mass of NO3 and TN was greater in the 25% biochar treatment leachate, whereas the mass of ammonium (NH4) was unaffected. In hydrangea, total nutrients lost from the containers was lower in biochar-amended containers (both 10% and 25% biochar) because of receiving a lower total volume of water. Amendment with biochar also affected concentration of phosphorus (P) and K, with the highest concentration in both leaf tissue and substrate from the 25% biochar application rate.

Incorporation of Biochar Carbon into Stable Soil Aggregates: The Role of Clay Mineralogy and Other Soil Characteristics

Aggregation and structure play key roles in water-holding capacity and stability of soils. In this study, the incorporation of carbon (C) from switchgrass biochar into stable aggregate size fractions was assessed in an Aridisol (from Colorado, USA) dominated by 2:1 clays and an Alfisol (from Virginia, USA) containing weathered mixed 1:1 and 2:1 mineralogy, to evaluate the effect of biochar addition on soil characteristics. The biochar was applied at 4 levels, 0, 25, 50, and 100 g kg−1, to the soils grown with wheat in a growth chamber experiment. The changes in soil strength and water-holding capacity using water release curves were measured. In the Colorado soil, the proportion of soil occurring in large aggregates decreased, with concomitant increases in small size fractions. No changes in aggregate size fractions occurred in the Virginia soil. In the Colorado soil, C content increased from 3.3 to 16.8 g kg−1, whereas in the < 53 µm fraction C content increased from 5.7 to 22.6 g kg−1 with 100 g kg−1 biochar addition. In the Virginia soil, C content within aggregate size fractions increased for each size fraction, except the > 2 000 µm fraction. The greatest increase (from 6.2 to 22.0 g kg−1) occurred in the 53–250 µm fraction. The results indicated that C was incorporated into larger aggregates in the Virginia soil, but remained largely unassociated to soil particles in the Colorado soil. Biochar addition had no significant effect on water-holding capacity or strength measurements. Adding biochar to more weathered soils with high native soil organic content may result in greater stabilization of incorporated C and result in less loss because of erosion and transport, compared with the soils dominated by 2:1 clays and low native soil organic content.

Phenoxy herbicide removal from aqueous solutions using fast pyrolysis switchgrass biochar

The release of herbicides is known to negatively impact humans and the environment. We report the use of a low cost biochar (prepared through fast pyrolysis) to successfully remove phenoxy herbicides from aqueous solutions. The biochar was characterized using: FT-IR, SEM, pHpzc, elemental analysis, and surface area measurements. Sorption experiments were run at pH values from 2 to 10, adsorbate concentrations from 25 to 300 mg/L and temperatures from 25 to 45 °C. Adsorption isotherms were evaluated from 25 to 45 °C using both two parameter (Freundlich and Langmuir) and three parameter (Redlich–Peterson and Toth) adsorption isotherm models. The maximum adsorption capacities for 2,4-dichlorophenoxyacetic acid (2,4-D) and 2-methyl-4-chlorophenoxyacetic acid (MCPA) were Q0SGB∼134 mg/g and Q0SGB∼50 mg/g, respectively, at pH 2. This low surface area switchgrass biochar (1.1 m2/g) can adsorb far more MCPA per unit of measured surface area (45 mg/m2) than high surface area commercial activated carbons (1050–1150 m2/g) which absorb only 0.08–0.11 mg/m2, and are also expensive. This indicates that biochar three dimensional swelling occurs in an aqueous environment and adsorbates are imbibed and adsorbed at additional sorption sites.

Adsorption of metribuzin from aqueous solution using magnetic and nonmagnetic sustainable low-cost biochar adsorbents.

Switchgrass biochar (SGB) was made by fast pyrolysis in an auger-fed reactor at 425°C with a solid residence time of 60s in the pyrolysis zone during bio-oil production. Magnetic switchgrass biochar (MSGB) was prepared by iron oxide precipitation onto the biochar surface using an aqueous Fe3+/Fe2+ solution followed by NaOH treatment. Both the SGB and the MSGB were characterized by FTIR, SEM, SEM-EDX, TGA, pHpzc, elemental analysis, and surface area measurements. Batch sorption studies of metribuzin from aqueous solutions were carried out at different pH values, adsorbate concentrations, and temperatures. The adsorption of metribuzin onto both biochars was highest at a pH of 2. Adsorption isotherms were evaluated from 25 to 45°C using the Freundlich, Langmuir, Redlich-Peterson, Toth, Sips, Koble-Corrigan, and Radke-Prausnitz adsorption models. Langmuir adsorption capacities at pH 2 were Q 0SGB~151, 223, and 205mg/g and Q 0MSGB~155, 205, and 155mg/g at 25, 35, and 45°C, respectively. Low-cost magnetization of the biochar occurred without significant loss of absorption capacity, enabling facile separation of slurried biochar from liquids following contaminate absorption. Graphical abstract ᅟ.

Kinetics, isotherm, and thermodynamic studies of the adsorption of reactive red 195 A dye from water by modified Switchgrass Biochar adsorbent

A method is described for efficient decolorization of reactive red 195 A dye (RR-195A) from aqueous and wastewater samples using modified Switchgrass Biochar (SB) by tetradecyltrimethyl ammonium bromide (TTAB) as a cationic surfactant for the formation of a novel SB-TTAB adsorbent. The different controlling experimental conditions such as solution pH, initial dye concentration, contact time, adsorbent mass, interfering ions and temperature have been investigated and optimized. Adsorption equilibrium using Langmuir, Freundlich, Temkin and Dubinin–Radushkevich (D–R) isotherm models have been also studied and the best fit was related to the Langmuir adsorption isotherm. Adsorption kinetics have been tested and illustrated using pseudo first-order, pseudo-second-order, intraparticle diffusion and Elovich models. The collected results confirmed that the pseudo-second order kinetic model exhibited the best fit with the experimental data. Thermodynamic parameters were calculated and the results referred to an exothermic nature and spontaneity of the adsorption process. Improved decolorization of reactive red 195 A dye from textile industrial wastewater and other water samples were successfully established. Excellent recovery values of RR-195A dye by SB-TTAB adsorbent were determined in the ranges of 96.61–98.76%, 97.79–99.26%, 94.24–100.0% and 90.98–92.96% (±1.0–4.0%) from tap water, raw water, wastewater and sea water, respectively.

Switchgrass Biochar Effects on Plant Biomass and Microbial Dynamics in Two Soils from Different Regions

Biochar amendments to soils may alter soil function and fertility in various ways, including through induced changes in the microbial community. We assessed microbial activity and community composition of two distinct clayey soil types, an Aridisol from Colorado (CO) in the U.S. Central Great Plains, and an Alfisol from Virginia (VA) in the southeastern USA following the application of switchgrass (Panicum virgatum) biochar. The switchgrass biochar was applied at four levels, 0%, 2.5%, 5%, and 10%, approximately equivalent to biochar additions of 0, 25, 50, and 100 t ha−1, respectively, to the soils grown with wheat (Triticum aestivum) in an eight-week growth chamber experiment. We measured wheat shoot biomass and nitrogen (N) content and soil nutrient availability and N mineralization rates, and characterized the microbial fatty acid methyl ester (FAME) profiles of the soils. Net N mineralization rates decreased in both soils in proportion to an increase in biochar levels, but the effect was more marked in the VA soil, where net N mineralization decreased from −2.1 to −38.4 mg kg−1. The 10% biochar addition increased soil pH, electrical conductivity, Mehlich- and bicarbonate-extractable phosphorus (P), and extractable potassium (K) in both soil types. The wheat shoot biomass decreased from 17.7 to 9.1 g with incremental additions of biochar in the CO soil, but no difference was noted in plants grown in the VA soil. The FAME recovery assay indicated that the switchgrass biochar addition could introduce artifacts in analysis, so the results needed to be interpreted with caution. Non-corrected total FAME concentrations indicated a decline by 45% and 34% with 10% biochar addition in the CO and VA soils, respectively, though these differences became nonsignificant when the extraction efficiency correction factor was applied. A significant decline in the fungi:bacteria ratio was still evident upon correction in the CO soil with biochar. Switchgrass biochar had the potential to cause short-term negative impacts on plant biomass and alter soil microbial community structure unless measures were taken to add supplemental N and labile carbon (C).

Influence of Pyrolysis Temperature and Production Conditions on Switchgrass Biochar for Use as a Soil Amendment

Biochars form recalcitrant carbon and increase water and nutrient retention in soils; however, the magnitude is contingent upon production conditions and thermo-chemical conversion processes. Herein we aim at (i) characterizing switchgrass (Panicum virgatum L.)-biochar morphology, (ii) estimating water-holding capacity under increasing ratios of char: soil; and, (iii) determining nutrient profile variation as a function of pyrolysis conversion methodologies (i.e. continuous, auger pyrolysis system versus batch pyrolysis systems) for terminal use as a soil amendment. Auger system chars produced at 600°C had the greatest lignin portion by weight among the biochars produced from the continuous system. On the other hand, a batch pyrolysis system (400 °C – 3h) yielded biochar with 73.10% lignin (12 fold increases), indicating higher recalcitrance, whereas lower production temperatures (400 °C) yielded greater hemicellulose (i.e. greater mineralization promoting substrate). Under both pyrolysis methods, increasing biochar soil application rates resulted in linear decreases in bulk density (g cm-3). Increases in auger-char (400 °C) applications increased soil water-holding capacities; however, application rates of >2 Mt ha-1 are required. Pyrolysis batch chars did not influence water-holding abilities (P>0.05). Biochar macro and micronutrients increased, as the pyrolysis temperature increased in the auger system from 400 to 600 °C, and the residence time increased in the batch pyrolysis system from 1 to 3 h. Conversely, nitrogen levels tended to decrease under the two previously mentioned conditions. Consequently, not all chars are inherently equal, in that varying operation systems, residence times, and production conditions greatly affect uses as a soil amendment and overall rate of efficacy.

Nutrient release from switchgrass-derived biochar pellets embedded with fertilizers

Biochar pellets produced by blending switchgrass biochar, lignin and fertilizers K and P together followed by pelletization were characterized and investigated for their ability to release K and P. Pellets processed at 180°C with increasing lignin content from 10 to 30wt.% had higher density, thermal stability and durability, and produced lower pore volume and smaller pore size than pellets processed at 105°C. Fertilizer-embedded biochar pellets with 10–30wt.% lignin and processed at 180°C had a slower K and P release than pellets dried at 105°C, with release rates (53–62% in K and 49–62% in P) within the first 24h followed by gradual releases (78–87% in K and 73–78% in P) for the next 18days. Therefore, by controlling lignin content and processing temperature of the pellets, one can control the release rate of nutrients present in biochar pellets.

Characterization of Biochar from Switchgrass Carbonization

Switchgrass is a high yielding, low-input intensive, native perennial grass that has been promoted as a major second-generation bioenergy crop. Raw switchgrass is not a readily acceptable feedstock in existing power plants that were built to accommodate coal and peat. The objective of this research was to elucidate some of the characteristics of switchgrass biochar produced via carbonization and to explore its potential use as a solid fuel. Samples were carbonized in a batch reactor under reactor temperatures of 300, 350 and 400 °C for 1, 2 and 3 h residence times. Biochar mass yield and volatile solids decreased from 82.6% to 35.2% and from 72.1% to 43.9%, respectively, by increasing carbonization temperatures from 300 °C to 400 °C and residence times from 1 h to 3 h. Conversely, biochar heating value (HV) and fixed carbon content increased from 17.6 MJ kg−1 to 21.9 MJ kg−1 and from 22.5% to 44.9%, respectively, under the same conditions. A biomass discoloration index (BDI) was created to quantify changes in biochar colors as affected by the two tested parameters. The maximum BDI of 77% was achieved at a carbonization temperature of 400 °C and a residence time of 3 h. The use of this index could be expanded to quantify biochar characteristics as affected by thermochemical treatments. Carbonized biochar could be considered a high quality solid fuel based on its energy content.

Phosphorus Sorption and Availability from Biochars and Soil/Biochar Mixtures

In an energy‐limited world, biomass may be converted to energy products through pyrolysis. A byproduct of this process is biochar. A better understanding is needed of the sorption characteristics of biochars, which can influence the availability of plant essential nutrients and potential water contaminants such as phosphorus (P) in soil. Knowledge of P retention and release mechanisms when applying carbon‐rich amendments such as biochar to soil is needed. The objectives of this study were to quantify the P sorption and availability from biochars produced from the fast pyrolysis of corn stover (Zea mays L.), Ponderosa pine (Pinus ponderosa Lawson and C. Lawson) wood residue, and switchgrass (Panicum virgatum L.). We determined the impact of biochar application to soils with different chemical characteristics on P sorption and availability. Sorption of P by biochars and soil–biochar mixtures was studied by fitting the equilibrium solution and sorbed concentrations of P using Freundlich and Langmuir isotherms. Biochar produced from Ponderosa pine wood residue had very different chemical characteristics than corn stover and switchgrass. Corn stover biochar had the highest P sorption (in average 79% of the initial solution P concentration) followed by switchgrass biochar (in average 76%) and Ponderosa pine wood residue biochar (in average 31%). Ponderosa pine wood residue biochar had higher bicarbonate extractable (available) P (in average 43%) followed by switchgrass biochar (33% of sorbed P) and corn stover biochar (25% of sorbed P). The incorporation of biochars to acidic soil at 40 g/kg (4%) increased the equilibrium solution P concentration (reduced the sorption) and increased available sorbed P. In calcareous soil, application of alkaline biochars (corn stover and switchgrass biochars) significantly increased the sorption of P and decreased the availability of sorbed P. Biochar effects on soil P was aligned with their chemical composition and surface characteristics.

Effect of biochar on chemical properties of acidic soil

The effect of biochar addition on the chemical properties of acidic soil such as soil pH, electrical conductivity (EC), cation exchange capacity (CEC), and exchangeable acidity were investigated to determine the liming potential of biochars. This study was conducted by incubating acidic soil (clayey, smectitic, acid, mesic, shallow, Aridic Ustorthent) of pH < 4.80 with biochars for 165 days. The biochars were produced from two biomass feedstocks such as corn stover (Zea mays L.) and switchgrass (Panicum virgatum L.) using microwave pyrolysis (at 650°C). Corn stover biochar, switchgrass biochar, and lime (calcium carbonate) were applied at four rates (0, 52, 104, and 156 Mg ha−1) to acidic soil. Amendment type, application rate, and their interaction had significant effects (p < 0.05) on soil pH, EC, and CEC of acidic soil. Exchangeable acidity was significantly affected by amendment type. Application of corn stover biochar had shown a relatively larger increase in soil pH than switchgrass biochar at all application rates. The ameliorating effect of biochars on chemical properties of acidic soil was consistent with their chemical composition.

Comparing Corn Stover and Switchgrass Biochar: Characterization and Sorption Properties

A switchgrass biochar (SB) produced by fast pyrolysis and a corn stover biochar (CSB) from a slow pyrolysis process were mechanically milled and characterized. Both of these biochars are very cost-effective and originate as residues from bioenergy production and the corn industry, respectively. These two biochars were evaluated for their sorptive properties with both water and the estrogen containing compounds estrone, b-estradiol, and zearalenone via batch rebinding assays in salt solutions. Although CSB had greater total surface area than SB, SB was a more porous biochar, indicated by its greater micropore surface area. For both water and all estrogen containing compounds, SB had better sorptive capability, most likely due to its higher micropore surface area. These results suggest ball milled biochars from switchgrass and corn stover offer promise for a sustainable approach to removing toxins from water.

Switchgrass Biochar Affects Two Aridisols

The use of biochar has received growing attention because of its ability to improve the physicochemical properties of highly weathered Ultisols and Oxisols, yet very little research has focused on its effects in Aridisols. We investigated the effect of low or high temperature (250 or 500°C) pyrolyzed switchgrass () biochar on two Aridisols. In a pot study, biochar was added at 2% w/w to a Declo loam (Xeric Haplocalcids) or to a Warden very fine sandy loam (Xeric Haplocambids) and incubated at 15% moisture content (by weight) for 127 d; a control (no biochar) was also included. Soils were leached with 1.2 to 1.3 pore volumes of deionized HO on Days 34, 62, 92, and 127, and cumulative leachate Ca, K, Mg, Na, P, Cu, Fe, Mn, Ni, Zn, NO-N, NO-N, and NH-N concentrations were quantified. On termination of the incubation, soils were destructively sampled for extractable Cr, Cu, Fe, K, Mg, Mn, Na, Ni, P, Zn, NO-N, and NH-N, total C, inorganic C, organic C, and pH. Compared with 250°C, the 500°C pyrolysis temperature resulted in greater biochar surface area, elevated pH, higher ash content, and minimal total surface charge. For both soils, leachate Ca and Mg decreased with the 250°C switchgrass biochar, likely due to binding by biochar's functional group sites. Both biochars caused an increase in leachate K, whereas the 500°C biochar increased leachate P. Both biochars reduced leachate NO-N concentrations compared with the control; however, the 250°C biochar reduced NO-N concentrations to the greatest extent. Easily degradable C, associated with the 250°C biochar's structural make-up, likely stimulated microbial growth, which caused NO-N immobilization. Soil-extractable K, P, and NO-N followed a pattern similar to the leachate observations. Total soil C content increases were linked to an increase in organic C from the biochars. Cumulative results suggest that the use of switchgrass biochar prepared at 250°C could improve environmental quality in calcareous soil systems by reducing nutrient leaching potential.

Removal of copper and cadmium from aqueous solution using switchgrass biochar produced via hydrothermal carbonization process

Biochar produced from switchgrass via hydrothermal carbonization (HTC) was used as a sorbent for the removal of copper and cadmium from aqueous solution. The cold activation process using KOH at room temperature was developed to enhance the porous structure and sorption properties of the HTC biochar. The sorption efficiency of HTC biochar and alkali activated HTC biochar (HTCB) for removing copper and cadmium from aqueous solution were compared with commercially available powdered activated carbon (PAC). The present batch adsorption study describes the effects of solution pH, biochar dose, and contact time on copper and cadmium removal efficiency from single metal ion aqueous solutions. The activated HTCB exhibited a higher adsorption potential for copper and cadmium than HTC biochar and PAC. Experiments conducted with an initial metal concentration of 40 mg/L at pH 5.0 and contact time of 24 h resulted in close to 100% copper and cadmium removal by activated HTCB at 2 g/L, far greater than what was observed for HTC biochar (16% and 5.6%) and PAC (4% and 7.7%). The adsorption capacities of activated HTCB for cadmium removal were 34 mg/g (0.313 mmol/g) and copper removal was 31 mg/g (0.503 mmol/g).