Surface Roughness Tester Research Articles

The differences in surface roughness and hardness of glass ionomers cement coated with vaseline and cocoa butter after immersion in UHT milk

Background: Dental caries affects 513.8 million children globally, and glass ionomer cement (GIC) is a common treatment due to its fluoride release. However, GIC is moisture-sensitive and prone to solubility during maturation. UHT milk, often consumed by children, disrupts ionic bonds on GIC surfaces affecting roughness and hardness. Increased surface roughness leads to plaque accumulation, while decreased surface hardness ensures compressive strength and abrasion resistance. Coating agents like vaseline and cocoa butter help preserve GIC properties by maintaining roughness and hardness. Purpose: To analyze differences in surface roughness and hardness values of GIC treated with vaseline, cocoa butter, and without coating after being immersed in UHT milk for 7 days. Methods: The experimental study used a post-test control group design with three groups of six specimens each, immersed in UHT milk for seven days. Groups included GIC without coating, coated with vaseline, and cocoa butter. The test results were then measured using a surface roughness tester and Vickers hardness tester and analyzed using the ANOVA. Results: GIC coating with vaseline has the lowest value of surface roughness and highest surface hardness, followed by GIC coating with cocoa butter and without coating. However, the three groups did not have significant differences in statistical data analysis. Conclusion: There is no difference in the surface roughness and hardness values of GIC without coating, coated with vaseline, or cocoa butter after being immersed in UHT milk for 7 days.

Mechanical behavior of coconut coir reinforced by epoxy resin composites

In the present work, a new analysis of coconut coir mechanical behavior reinforced by epoxy resin (CCER) composites was presented. The mixing composites were fabricated using the compression molding technique to produce three eco-friendly ratios between natural and synthetic materials. These composites ratios are 75% of coconut coir and 25% of epoxy (75C25E), 80% of coconut coir and 20% of epoxy (80C20E), and 85% of coconut coir and 15% of epoxy (85C15E). The images of the coconut coir were captured using a Nikon SMZ 745T microscope and their mechanical properties were analyzed using tensile, impact, and surface roughness tests. The collected data were analyzed using statistical analysis. Numerical computations and graphical demonstrations are carried out to observe the mechanical behavior of the CCER composites according to the three ratios. The different ratios of CCER composites will be affected by their mechanical behavior. The outcomes demonstrated that due to the synergistic effect of reinforcements, the composite with 75% coconut coir had better mechanical behavior than the other composites. Furthermore, the mechanically tested samples were subjected to a surface roughness test to investigate the impact of CNC router machine spindle speed parameters.

Experimental Investigation on the Machining Behaviour, Surface Integrity and Tool Wear Analysis in Environment Friendly Milling of Inconel 825

The study investigated end milling of Inconel 825 with varying spindle speed (N), feed rate (f) and axial depth of cut (da) with Minimum Quality Lubricant (MQL) and flooded lubrication. Molybdenum disulfide (MoS2) with the average particle size of 10 µm was used as lubricating agent. Work considered, center line average of roughness profile as a measure of surface roughness which was measured with a surface roughness tester. Material Removal Rate (MRR) was also measured experimentally using weight difference. The influence of spindle speed (N), feed rate (f) and axial depth of cut (da) during end milling of Inconel 825 on surface roughness and MRR were studied. Prediction of surface roughness by ANOVA linear model for MQL condition was found functionally adequate with R2 = 89.25% which fits with the experimental values. Also, the prediction and optimization of surface roughness using Response Surface Methodology (RSM) was proposed. It was found that, RSM model for MQL condition produced good agreement with the measurement of the given range of input cutting conditions with the prediction capability of 91.66%. Further, the machined surfaces and tool wear were analyzed using Scanning Electron Microscope (SEM) to understand the mechanisms of wear.

Effect of Drying Oil on Properties of Traditional Painted Coatings

This study examines the effects of drying oils—Tung and linseed—on the properties of traditional polychrome coatings applied to wood. Samples prepared with cinnabar, malachite green, yellow ochre, and azurite pigments were analyzed using colorimetric, gloss measurements, surface roughness testing, adhesion strength, and SEM imaging. The results show that Tung oil generally enhances gloss by over 20% and provides superior adhesion, consistently achieving an adhesion grade of 0 (no peeling) across all pigments. Linseed oil, although effective at higher concentrations, displayed more variable adhesion, particularly with blue and yellow pigments. Surface roughness measurements revealed that higher oil content (6:4 ratio) reduced roughness, achieving smoother finishes with Ra values as low as 2.36 μm for Tung oil. SEM analysis confirmed that Tung oil yields a smoother and more even pigment distribution compared to the rougher, clustered morphology in linseed oil samples. These findings underscore the importance of oil type and concentration in achieving desired esthetic and durability outcomes in restoration work.

Comparison of Mechanical and Surface Properties between Conventional and CAD/CAM Provisional Restorations.

This study compared the flexural strength, surface hardness, and surface roughness of conventional, milled, and three-dimensional (3D)-printed provisional restorations. Bar-shaped polymethyl methacrylate (PMMA) specimens (25 × 2 × 2 mm3) and disc-shaped specimens (9 × 2 mm2) were fabricated using three different techniques (n = 10/group): conventional (SR Ivocron C&B, Ivoclar Vivadent, Schaan, Liechtenstein), milling (Aidite Temp PMMA Blocks, Aidite, Qinhuangdao, China), and 3D printing (Asiga DentaTOOTH, Asiga, Sydney, Australia). Flexural strength was evaluated using a universal testing machine until fracture occurred. Vickers hardness and surface roughness tests were performed on the disc-shaped specimens using a micro-Vickers hardness tester and atomic force microscopy, respectively. Data were statistically analyzed using one-way ANOVA. The post hoc Tukey's honest significant difference was conducted to compare the differences value between groups (p < 0.05). The milled computer-aided design/computer-aided manufacturing (CAD/CAM) provisional restorative material exhibited a significantly higher flexural strength (125.16 ± 6.83 MPa) compared with both the traditional (109.74 ± 14.14 MPa) and 3D-printed (71.09 ± 9.09 MPa) materials (p < 0.05). The conventional material had a higher Vickers hardness (19.27 ± 0.41 kgf/mm2) compared with the milled (18.53 ± 0.32 kgf/mm2) and 3D-printed (17.80 ± 1.85 kgf/mm2) materials, though the difference was statistically significant only between the conventional and 3D-printed groups. The surface roughness of the milled CAD/CAM material (8.80 ± 2.70 nm) was significantly lower than that of the 3D-printed material (24.27 ± 9.82 nm) (p < 0.05). The provisional restorations fabricated using milled PMMA technology provide adequate flexural strength, surface hardness, and low surface roughness, offering a viable alternative for creating provisional restorations.

Evaluating process parameters of SLS part of polyamide-12 recycled powder using RSM

Abstract Selective laser sintering (SLS) is a highly flexible rapid prototyping (RP) technology which can use a wide range of powdered materials to generate high quality complex geometries directly from digital models. The SLS process uses a laser to sinter selected areas of powdered materials to produce solid objects layer by layer, according to the 2D data obtained from CT scan or MRI imaging techniques. This paper presents research work for evaluating the effect of process parameters on impact toughness and surface roughness of the part manufactured on Farsoon SS402P SLS from recycled ageing FS 3300PA which is PA-12 based powder and standard operating parameters using Response Surface Methodology (RSM) design of experiments. Impact tests have been performed as per the ASTM D6110 standard using recommendations from ISO 179-2. According to the results, effect of process parameters are successfully analyzed by employing impact toughness and surface roughness tests. Based on the results of the ANOVA analysis, impact toughness increases with increasing laser power (4.467 j/cm2 at 72.5 watts). Similarly, it is also clear from the results that the region with the lowest laser power, high layer thickness, and 90-degree orientation had the lowest surface roughness (3.46 μm).

The effect of soaking blimbi (Averrhoa blimbi, L) fruit extract on the roughness of nanofiller composite resin

Background Nanofiller composite resin is a restorative material or filling material that is activated by visible light to restore anterior and posterior teeth. One of the characteristics of the composite resin surface is surface roughness. Surface roughness is greatly influenced by acidic solutions, namely the acid in drinks. Objective: To determine the effect of soaking blimbi fruit extract (Averrhoa blimbi L.) on the roughness of nanofiller composite resin. Research Method: This research uses laboratory experimental research. The sampling method used 6 sample groups in each group, consisting of 4 groups, namely 2 treatment groups and 2 control groups. The treatment group consisted of 50% and 100% blimbi fruit extract, then the control group consisted of a positive control grup (citric acid) and a negative control (aquadest). Then a surface roughness test was carried out on each group using a Surface Roughness Tester tool, then the test data was analyzed using the One-Way Anova test with the condition that the data had to be normal and homogeneous, the condition for the One-Way Anova test was that the sig value Sig &lt;0.05. Results: Based on analysis using One-Way Anova, the sig 0.518 (p&gt;0.05), which means there are no significant differences in each sample group. Conclusion: There is no influence on the roughness of the nanofiller composite resin by soaking in star fruit extract (Averrhoa blimbi, L) because the value difference is not significant.

Effects of Coated Carbide Insert on Surface Finish of Multiple Hardened EN31 Alloy Steel Using Regression, ANN, and RSM

Objectives: Surface finish plays an essential role in every machining process. The current study mainly focuses on multiple hardened EN31 alloy steel, using various machining parameters and optimizing using regression, ANN, and RSM. Methods: The experimentation was performed using a commercial CNC machine and a surface roughness tester, using machining parameters such as tool nose radius (re), cutting speed (v), feed (f), depth of cut (d), and hardness (H) of the material ranging from 0.4 to 1.2 mm, 160 to 260 m/min, 0.1 to 0.20 mm/rev, 0.05 to 0.15 mm, and 45 to 49 HRC, respectively. Findings: The study revealed that cutting speed and feed rate significantly affect the surface finish, followed by tool nose radius. With the help of optimization techniques, the surface roughness predicted through RSM was 99.91%, followed by Regression and ANN. The contour plot predicts Ra using the best possible combinations of machining parameters. Novelty: The current research compares the surface finish results of multiple hardened EN31 alloy steels predicted through regression, RSM, and ANN with experimental values. The generated correlations will undoubtedly assist researchers in determining surface finish for the defined ranges of machining parameters. Keywords: Hard Turning, Coated Carbide, EN31 Steel, Surface Roughness, Optimization, RSM

Effects of Er:YAG laser debonding on changes in the properties of dental zirconia.

To investigate changes in the optical and mechanical properties of novel zirconia ceramics applied in dentistry after Er:YAG laser debonding and to evaluate the feasibility and value of reusing zirconia restorations debonded by an Er:YAG laser. Four types of zirconia ceramics were investigated: self-glazed zirconia (SGZ), 3Y-TZP, 4Y-PSZ and 5Y-PSZ. Forty rectangular (25 mm*8 mm*1.5 mm) specimens were fabricated for each zirconia type, and a total of 160 specimens were manufactured. The zirconia specimens were divided into four subgroups according to the applied Er:YAG laser debonding process: the control group, 4 W laser group, 5 W laser group, and 6 W laser group. For each subgroup, 10 specimens were subjected to color tests (color difference (△E) and transparency parameter (TP) tests) and subsequent mechanical tests (flexural strength (FS), elastic modulus (EM), Vickers hardness (VH) and surface roughness (Ra) tests). The △E, TP, FS, EM, VH and Ra values were measured and calculated. One random sample from each subgroup was observed by SEM. Statistical analyses were performed by one-way ANOVA followed by post hoc comparisons (α = 0.05). The △E and TP values after Er:YAG laser debonding were not significantly different among the subgroups (P > 0.05). However, the 6 W laser group had the highest △E and lowest TP. The ranges of changes in △E and TP were below the clinically detectable threshold (△E = 1.2, △TP = 1.33). In terms of the mechanical properties, there were no significant differences in the FS, EM, VH or Ra among the subgroups. No obvious microcracks were detected on the surfaces of the zirconia specimens during SEM. Er:YAG laser debonding does not obviously affect the optical or mechanical properties of novel zirconia ceramics in dentistry. Moreover, it is potentially feasible and valuable to reuse zirconia restorations after Er:YAG laser debonding.

Tribological effects of varying volumetric energy density in additive manufacturing of inconel 718

Abstract This study investigates the novel effects of varying volumetric energy density (VED) ratios on the tribological characteristics of Inconel 718 alloy fabricated using Laser Powder Bed Fusion (LPBF) process. Nine VED ratios were investigated, and samples underwent non-contact surface roughness tests, Vickers microhardness tests, and residual stress analysis. Notably, this study identified specific VED conditions where superior wear resistance was achieved, contributing new insights into optimizing LPBF parameters for tribological performance. Based on preliminary analysis, samples 1, 3, and 8 were selected for ball-on-disc wear testing. Sample 8, fabricated with 330 W laser power, 50 mm s−1 scan speed, 0.10 mm hatch spacing, and 0.05 mm layer thickness, demonstrated superior tribological behaviour with a 32.12% and 52.11% lower friction coefficient and 31% and 29.92% less mass loss compared to samples 1 and 3, respectively. The presence of γ-Ni, γ′-Ni3 (Al, Ti), γ-FCC, and γ′-L12 phases, along with microstructural features such as columnar and cellular dendritic structures, were confirmed via SEM and x-ray diffraction analyses. This study’s novel findings contribute valuable knowledge for optimizing Inconel 718 production via LPBF, particularly in enhancing wear resistance through tailored VED settings.

Bioactive Compounds Enhance the Biocompatibility and the Physical Properties of a Glass Ionomer Cement.

In order to characterize a novel restorative material, knowledge about the toxicological effect on human cells and the physical behavior of a glass ionomer cement (GIC) containing flavonoids was established. The flavonoids apigenin, naringenin, quercetin, and liquiritigenin were manually incorporated into a GIC. In the control group, no incorporation was performed. Two cell culture assays evaluated the toxicity of GICs: SRB and MTT. For both assays, the keratinocyte cell line (HaCaT) was exposed to GIC (n = 3/group) for 24 h. The physical properties of the GICs were evaluated by compressive strength (n = 10), surface roughness (n = 10), and hardness (n = 10) tests. Cell viability by SRB ranged from 103% to 97%. The control revealed a significant decrease in the metabolism of cells (61%) by MTT, while the GIC+apigenin slightly increased the succinic dehydrogenase activity (105%; p > 0.05), also confirmed microscopically. The compressive strength and roughness values were similar among groups, but the hardness increased after the incorporation of naringenin and quercetin into GIC (p < 0.05). The incorporation of flavonoids positively altered the biological and physical properties of the GICs.

Augmenting bonding properties of OSB and Chinese fir hybrid cross-laminated timber by sandblasting pretreatment

The investigation was conducted into the adhesive performance within hybrid cross-laminated timber (HCLT) composed of sandblasted Chinese fir and oriented strand board (OSB) which was originally covered by cured adhesive during the manufacture leading to very fragile bonding. HCLT specimens with three layers were bonded utilizing three structural adhesives which were polyresorcinol formaldehyde (PRF), polyurethane (PUR), and polyisocyanate (EPI). Surface roughness and wettability testing ascertained that sandblasting could effectively change the original resin layer and microtopography on the surface of OSB laminates, significantly modified the level of roughness on the surface, thereby providing a basis for vertical spreading and permeating of the adhesives. Sandblasting pretreatment consistently augmented the dry bonding shear strength about all the three adhesives, achieving the most substantial increases of 53 %, 39 %, and 37 % for PRF, PUR, and EPI, respectively. The pretreatment further reducing delamination rates to about a half in cyclic delamination tests of all three adhesives. Fluorescence microscopy detection of the bonding interfaces revealed a significant increase in adhesive penetration depth which had been further confirmed by the bonding interface thickness measurement. Surface roughness generally had a negative effect on dry shear bonding strength, especially with EPI adhesive, while surface wettability was positively correlated with bonding strength and adhesive layer thickness. This study introduced an environmental and efficient method to enhance the bonding performance of HCLT.

Surface Roughness Evaluation of Blast-Cleaned Structural Steel Plates Considering Measurement Deviation

Surface roughness is an important characteristic of blast-cleaned structural steel plates. This is because the adhesion of the coating and the frictional grip of the bolted connections are related to surface roughness. Surface roughness is usually measured using a surface roughness meter. Because the roughness of blast-cleaned surfaces is not uniform, it varies from position to position. The surface roughness test results obtained from a broad area are more valuable than those obtained from a narrow area. Because the measured values contain deviations, they are measured multiple times and averaged to reduce the influence of deviations. However, to evaluate roughness, it is necessary to clarify the measurement conditions to obtain accurate results. Consider combining these sentences as follows: In this study, the surface roughness of the blast-cleaned structural steel sample was measured at multiple locations to obtain its distribution characteristics. During each sample measurement, the detection sensor of the surface roughness meter was lifted and placed on the steel sample to determine deviations from the actual results. The surface roughness distributions of five blast-cleaned samples were the same under the identical measurement conditions. This indicates that accurate results can be obtained by measuring representative samples, without the need for measuring all samples; actually, 17 measurements were adequate to obtain a mean surface roughness value with a 95% confidence level and a 5% acceptable error rate.

Physical and microstructural properties of YSZ + Cr2O3 thermal barrier coatings developed using HVOF technique

A composite coating material of Yttria-Stabilized Zirconia (YSZ) and Chromium Oxide (Cr2O3) was developed on the surface of Al-6061 substrates. The coating consisting of equal measures of the composite material of YSZ and Cr2O3 was successfully obtained using the High-Velocity Oxy Fuel (HVOF) technique. The surface roughness and coating thickness of the composite coatings are evaluated. The surface roughness (Ra) was evaluated showing an average of 6.0848 µm using the Surface Roughness Tester (SRT). The coating thickness was evaluated showing an average of 220.8 µm using the Coating Thickness Tester (CTT). The surface roughness and the coating thickness obtained are comparable to typical physical properties of Thermal Barrier Coatings (TBC’s). The microstructural evaluation of the coated specimens was performed through the Scanning Electron Microscope (SEM), showing the clear unification of materials The determination of the elemental composition of surface coatings was performed through the EDAX tests, which clearly established the elements in the coatings. This article is indicative of the achievement of TBC’s consisting of composite materials though HVOF technique as an alternative to TBC’s obtained through surface coats and bond coats.

Exploring surface integrity: Experimental investigation into abrasive waterjet deep hole drilling on ss 316L for biomedical applications

Precision drilling of difficult-to-cut materials with exceptional surface integrity is a crucial factor in producing advanced manufactured components in industries like aviation, automotive, defense, electronic, and medical devices. More specifically, deep hole drilling enables precise customization of prostheses, improving patient comfort and functionality. Abrasive waterjet deep hole drilling has become a vital drilling technique in many industries due to its adaptability and effectiveness in drilling intricate shapes on hard-to-cut materials. The interplay between process parameters and surface finish underscores the need for systematic investigation to enhance drilling efficiency and quality. In this research, an attempt has been made to explore the influence of abrasive waterjet deep hole process parameters viz water pressure and standoff distance on the surface integrity of the drilled holes for biomedical applications. A surface roughness tester has been used to evaluate surface roughness at three distinctive places, namely the top, middle, and bottom of the drilled holes. The investigation showed that surface roughness at the top of the holes is less as compared to the middle and bottom of the holes. The average surface roughness along the depth of the drilled holes is greatly influenced by water pressure. Additionally, the morphology of the drilled holes has been studied using a scanning electron microscope (SEM). SEM images revealed that the top surface of the drilled holes is free from defects.

Evaluating the Surface Properties of Prosthodontic Polymer Impression Materials

Surface properties of prosthodontic polymer impression materials, such as hardness, roughness, and accuracy, are crucial for the accurate replication of oral structures in restorative dentistry. To evaluate the surface properties by using different types of polymer impression materials commonly used in dentistry and analyze their surface characteristics. Materials and methods: Forty -five samples of materials were used, including alginate (irreversible hydrocolloid), condensation silicone (putty) and addition silicone (putty), study was conducted at the advanced medical polymer group in the Libyan Polymer Research Center to evaluate the surface properties of prosthodontic polymer impression materials. Three evaluation methods were used: Shore hardness testing, surface roughness testing, and dimensional accuracy measurements. Data analysis included mean, standard deviation, and One-way ANOVA calculations. Alginate has a lower hardness compared to addition silicone (putty) and condensation silicone (putty). The ANOVA test for surface roughness showed no significant differences among the materials, with a p-value of 0.027. For shore hardness, there were no significant differences among the materials, with a p-value of 0.000. The ANOVA test for dimensional accuracy showed no significant differences among the different periods for alginate, condensation silicone (putty) and addition silicone (putty), with p-values of 0.000 respectively. The study concluded that alginate had the lowest hardness and roughness compared to condensation silicone (putty) and addition silicone (putty). There are no significant differences among the material surface properties (Shore hardness and surface roughness) but not in dimensional accuracy among the materials. This information provides valuable insights for dental professionals working with impression material.

Additive manufacturing of interlocking glass masonry units

In comparison to traditional glass casting, glass additive manufacturing (AM) presents an opportunity to increase design flexibility and reduce tooling costs for the production of highly variable geometries. While the latter has been extensively explored for masonry units, there is minimal research on the former for its viability to produce structural building components. This paper encompasses design, manufacturing, and experimental testing to assess the feasibility of using glass AM to produce interlocking masonry units for the construction industry. The glass 3D printer employed in this study is capable of printing a maximum volume of 32.5 × 32.5 × 38 cm–suitable for producing full-size masonry units. As part of this work, we discuss how to adapt design guidelines for glass AM to produce interlocking units. To evaluate fabrication ease and structural performance, three fabrication methods, Fully Hollow, Print-Cast, and Fully Printed, are compared. To compare the accuracy, repeatability, and structural capacity of each masonry unit, geometric analysis, surface roughness, and mechanical testing is conducted. Results varied by fabrication method, with average strength ranging from 3.64-42.3 MPa for initial fracture and 64.0–118 MPa for ultimate strength. Accuracy in print dimensions was less than 1 mm with a standard deviation of 0.14–1.6 mm. Results demonstrated that Fully Hollow masonry units provide a more immediate path to implementation, while Fully Printed units have the potential to provide an entirely glass, transparent, and circular building component fabrication method.

Laser-zoned treatment of magnesium surfaces with predictable degradation applications

Magnesium metal is a promising material for medical applications due to its biocompatibility and similar modulus of elasticity to human bone. However, its complex corrosion process must be addressed before it can be used clinically to match post-implantation tissue repair. This study aims to regulate material degradation by utilizing laser surface treatment. The surface of pure magnesium was modified using nanosecond and femtosecond laser methods to create various micro-nanostructures, such as chain, streak, column, and groove structures. Surface roughness and wettability tests revealed that the groove structures had higher roughness values. All structures exhibited hydrophilicity, but the femtosecond laser-generated structures were more hydrophilic. Electrochemical tests and immersion experiments demonstrated that femtosecond laser modification significantly improved the corrosion resistance of magnesium metal compared to polished samples. Cytotoxicity experiments showed that the laser-treated magnesium was not cytotoxic. Based on the results, we constructed various structures on the magnesium rods in different regions. As a result, the rods exhibited multi-stage biodegradation behavior in simulated body fluids (SBF). This study presents a novel approach to controlling the degradation sequence of medical metals.

Color Stability and Surface Roughness of Single-Shade Composite Resin after Finishing and Polishing

This study aims to evaluate the color stability and surface roughness of the single-shade composite resin after finishing and polishing for primary molars. A single-shade composite resin (OM, OMNICHROMA) and two multi-shade composite resins (FT, Filtek&lt;sup&gt;TM&lt;/sup&gt; Z350XT; ES, ESTELITE® SIGMA QUICK) were included. The specimens were divided into three subgroups using different polishing methods: control, Sof-Lex XT, and Sof-Lex Diamond. For color stability tests, cavities were prepared on extracted primary second molars and restored with experimental composite resins. Each specimen was immersed in the coffee solution for 48 hours. The color difference of each specimen was calculated. For surface roughness tests, cylindrical specimens were crafted with experimental composite resins. Surface roughness was analyzed using an atomic force microscope and a scanning electron microscope. In the color stability tests, FT demonstrated a significantly lower ΔE&lt;sub&gt;ab&lt;/sub&gt; than ES among the control groups, but no significant differences were observed between the ΔE&lt;sub&gt;ab&lt;/sub&gt; values of OM and FT or OM and ES. Additionally, no significant differences were found between the Sof-Lex XT and Sof-Lex Diamond subgroups in the three composite groups. Moreover, no significant differences in the surface roughness were found between the three composite groups, regardless of the polishing methods. The single-shade composite resin demonstrated comparable color stability and surface roughness to that of the multi-shade composite resins regardless of the polishing methods used in restoring primary molars. The single-shade composite resin is expected to be applicable in clinical pediatric dentistry reducing chair time due to the easy shade matching procedures.

Evaluation of the Surface Roughness and Solubility of Newer Self-blending Composite Resin following Home-bleaching and Brushing-mouth Rinsing Cycle

Objective(s): To evaluate the effect of tooth brushing and mouth rinsing after bleaching with 16% carbamide peroxide (16% CP) on the surface roughness and solubility of newer self-blending resin composite. Materials and Methods: About 70 specimens were fabricated with Estelite sigma-quick composite resin and subjected to bleaching using custom-tray with 16%CP gel for 6hours except 10 samples to serve as control group and divided into seven groups (n=10) as follows: group 1: no bleaching (control), group 2: 16% CP, group 3: brushing, group 4: brushing+Listerine mouth rinse, group 5: brushing +Colgate Plaxmouth rinse, group 6: Listerine, group 7: Colgate Plax. Electric tooth brushing was done using toothpaste slurry for 3min, immersed in mouth-rinse of respective groups for 1min and placed in artificial saliva for 24hrs. This was done for a total period of 21 days followed by surface roughness and solubility testing. Data were statistically analyzed using one-way ANOVA and post hoc Tuckey tests (p&lt;0.05). Results: Group 4 (Brushing + Listerine) showed greater surface roughness and solubility followed by group 6 (Listerine). No significant difference was found between group1 with group3 and group 5. Conclusion (s): Along with brushing, Listerine mouth rinse has a determining effect on surface roughness and solubility of newer self-blending composite resin following bleaching with 16% Carbamide peroxide.