Surface Hot-film Measurements Research Articles

Dynamics of Shock Waves Interacting With Laminar Separated Transonic Turbine Flow Investigated by High-Speed Schlieren and Surface Hot-Film Sensors

Abstract The results presented in this paper are based on experimental investigations on a generic transonic low pressure turbine profile at high subsonic exit Mach numbers. Here, the flow on the suction side reaches a maximum isentropic Mach number of approximately 1.2 and features a large separation bubble in a transonic flow regime characterized by surface hot-film measurements. The measurements are supplemented by Schlieren images recorded with a high-speed camera at 19.2 kHz. A highly unsteady normal shock wave on the suction side is observable upstream of the trailing edge. It is interacting with laminar separated flow which is rarely documented in literature. The interaction of the normal shock with the boundary layer flow seems to amplifies the ongoing transition process over the separation bubble and the flow reattaches shortly downstream. A statistical analysis of the Schlieren images reveals characteristic low frequencies of the shock wave motions and a pulsation of the separation bubble. Additionally, the statistical information of the time-dependent signal from the surface hot-film sensors demonstrate the instabilities influencing the boundary layer linked to the unsteadiness in the main flow.

Temperature decline thermography for laminar\u2013turbulent transition detection in aerodynamics

Detailed knowledge about laminar–turbulent transition and heat transfer distribution of flows around complex aerodynamic components are crucial to achieve highest efficiencies in modern aerodynamical systems. Several measurement techniques have been developed to determine those parameters either quantitatively or qualitatively. Most of them require extensive instrumentation or give unreliable results as the boundary conditions are often not known with the required precision. This work introduces the simple and robust temperature decline method to qualitatively detect the laminar–turbulent transition and the respective heat transfer coefficients on a surface exposed to an air flow, according to patent application Stadlbauer et al. (Patentnr. WO2014198251 A1, 2014). This method provides results which are less sensitive to control parameters such as the heat conduction into the blade material and temperature inhomogeneities in the flow or blade. This method was applied to measurements with NACA0018 airfoils exposed to the flow of a calibration-free jet at various Reynolds numbers and angles of attack. For data analysis, a post-processing method was developed and qualified to determine a quantity proportional to the heat transfer coefficient into the flow. By plotting this quantity for each pixel of the surface, a qualitative, two-dimensional heat transfer map was obtained. The results clearly depicted the areas of onset and end of transition over the full span of the model and agreed with the expected behavior based on the respective flow condition. To validate the approach, surface hotfilm measurements were conducted simultaneously on the same NACA profile. Both techniques showed excellent agreement. The temperature decline method allows to visualize laminar–turbulent transitions on static or moving parts and can be applied on a very broad range of scales—from tiny airfoils up to large airplane wings.

A two-element high-lift airfoil in disturbed flow conditions

This contribution presents experimental results of a two-element high-lift airfoil in a disturbed inflow. Permanent disturbances are generated by the wakes of two static airfoils located upstream of the research airfoil, one of which is a planar wake by an infinite airfoil and the other is a longitudinal vortex emanating from a finite wing. The disturbances induce spanwise gradients into the flow. The disturbed flow field is measured by Particle Image Velocimetry. The interaction of the disturbed flow field with the high-lift airfoil is investigated by means of static surface pressure close to the airfoil’s leading- and trailing-edge, as well as surface hotfilm measurements and oil flow visualizations on the high-lift flap. For small and moderate incidences the airfoil is mainly influenced by the circulation induced by the disturbances, which affect the effective flow angles. Local effects that result from the turbulence in the airfoil-wake and the induced transverse velocity of the disturbances are likewise considered. At high angle of attack, the prevailing stall conditions with strong variations in spanwise direction are discussed.

Experimental Study of the Plunging Motion with Unsteady Wind Tunnel Wall Interference Effects

A series of experiments were carried out to investigate unsteady behavior of the flow field as well as the boundary layer of an airfoil oscillating in plunging-type motion in a subsonic wind tunnel. The measurements involved surface-mounted hot films complimented with surface pressure. In addition, wind tunnel wall pressure distribution was acquired to furnish a baseline for the wall interference corrections. The airfoil is the section of a 660-kW wind turbine blade. The experiments were conducted at a Reynolds number of 0.42 million, and over two reduced frequencies of k = 0.06 and 0.085, at prestall, nearstall, and poststall regions. The unsteady aerodynamic loads were calculated from the surface pressure measurements, 64 ports, along the chord for both upper and lower surfaces of the model. The plunging displacements were transformed into the equivalent angle of attack. The surface hot-film measurements provided information about the boundary-layer events. The boundary-layer transition occurred via a laminar separation bubble. Variations of the surface pressure coefficients and aerodynamic loads with the equivalent angle of attack showed strong sensitivity to the reduced frequency and the mean angles of attack. The wall pressure distribution was affected by the model oscillation especially the region underneath the model.

The Effect of Leading-Edge Geometry on Wake Interactions in Compressors

The effect of leading-edge geometry on the wake/boundary-layer interaction was studied in a low-speed single-stage HP compressor. Both a 3:1 elliptic and a circular leading edge were tested on a controlled diffusion aerofoil stator blade. Experiments were undertaken on the stator suction surface; these included hotwire boundary-layer traverses, surface hotfilm measurements, and high resolution leading-edge pressure measurements. Steady computational fluid dynamics (CFD) predictions were also performed to aid the interpretation of the results. The two leading-edge shapes gave rise to significantly different flows. For a blade with an elliptic leading edge (Blade A), the leading-edge boundary layer remained attached and laminar in the absence of wakes. The wake presence led to the formation of a thickened laminar boundary layer in which turbulent disturbances were observed to form. Measurements of the trailing-edge boundary layer indicated that the wake/leading-edge interaction for Blade A raised the suction-surface loss by 20%. For a blade with a circular leading edge (Blade B), the leading-edge boundary-layer exhibited a separation bubble, which was observed to reattach laminar in the absence of wakes. The presence of the wake moved the separation position forward while inducing a turbulent reattachment upstream of the leading-edge time-average reattachment position. This produced a region of very high momentum thickness at the leading edge. The suction-surface loss was found to be 38% higher for Blade B than for Blade A. Wake traverses downstream of the blades were used to determine the total profile loss of each blade. The profile loss of Blade B was measured to be 32% higher than that of Blade A.