Superior Absorption Research Articles

Evaluation of polyester high-tenacity fabric and carbon nanotube reinforcements for improving flexural response in concrete beams.

This research scrutinized the effectiveness of utilizing polyester high tenacity fabrics to enhance the functionality of concrete panels. Two distinct woven fabrics with comparable strength resistance were fabricated and assessed. Concrete beams were compared in their original form and those reinforced with woven fabrics, along with beams reinforced with carbon nanotubes (CNTs) (B, BC2, BC4, BS1, and BS2). Results indicated that the textile-reinforced concrete panels displayed notably greater energy absorption capabilities post-failure under flexural loads in comparison to the control and CNT-reinforced panels. This enhanced performance was credited to the development of multiple cracking patterns in the textile-reinforced panels. The flexural behavior of the textile-reinforced panels was characterized by four discernible phases: a linearly increasing segment, a crack propagation phase featuring multiple cracking, a post-cracking phase with reduced stiffness, and ultimately, failure due to fabric rupture or debonding. Conversely, the control and CNT-reinforced panels exhibited a more brittle response post-initial cracking, with a limited number of cracks and reduced deformation capacity. The performance of the textile samples was largely unaffected by their specific characteristics, except for the fabric wrapping angle. The introduction of 0.04% CNTs marginally enhanced crack flexural resistance compared to the control and 0.02% CNT panels, owing to the varied distribution of CNTs within the matrix. Overall, the textile-reinforced concrete panels demonstrated superior load-bearing capacity, ductility, and energy absorption when compared to the other reinforcement techniques examined.

Dual-oxides confined carbonyl iron enabling superior electromagnetic wave absorption and anticorrosion performance

With the increasing requirements of electromagnetic wave (EMW) absorption, developing EMW absorbers with high-efficiency anti-corrosion performance which can be effectively applied in extreme corrosive environments is imperative and constitutes a hot issue in the current research. Herein, based on the composition modulation of ZrO2 and SiO2 layer, the dual-oxides confined carbonyl iron (CI@ZrO2/SiO2) composite displays a minimum reflection loss (RLmin) of −48.58 ​dB@1.9 ​mm and an effective absorption bandwidth (EAB) of 7.62 ​GHz@1.6 ​mm. Besides, the CI@ZrO2/SiO2 displays superior corrosion resistance with corrosion current density (icorr) of 8.62 ​× ​10−7 A/cm2 and polarization resistance (Rp) of 3.64×105 ​Ω. This work proposes a strategy to optimize the broadband EMW absorption properties as well as the mass production toward the corrosion resistance applications.

Pecan (Carya illinoinensis (Wangenh.) K. Koch) nuts as an emerging source of protein: extraction, physicochemical and functional properties.

The increasing demand for sustainable alternatives to traditional protein sources, driven by population growth, underscores the importance of protein in a healthy diet. Pecan (Carya illinoinensis (Wangenh.) K. Koch) nuts are currently underutilized as plant-based proteins but hold great potential in the food industry. However, there is insufficient information available on pecan protein, particularly its protein fractions. This study aimed to explore the physicochemical and functional properties of protein isolate and the main protein fraction glutelin extracted from pecan nuts. The results revealed that glutelin (820.67 ± 69.42 g kg-1) had a higher crude protein content compared to the protein isolate (618.43 ± 27.35 g kg-1), while both proteins exhibited amino acid profiles sufficient for adult requirements. The isoelectric points of protein isolate and glutelin were determined to be pH 4.0 and pH 5.0, respectively. The denaturation temperature of the protein isolate (90.23 °C) was higher than that of glutelin (87.43 °C), indicating a more organized and stable conformation. This is further supported by the fact that the protein isolate had a more stable main secondary structure than glutelin. Both proteins demonstrated improved solubility, emulsifying, and foaming properties at pH levels deviating from their isoelectric points in U-shaped curves. Compared to the protein isolate, glutelin displayed superior water and oil absorption capacity along with enhanced gelling ability. The protein isolate and glutelin from pecan nuts exhibited improved stability and competitive functional properties, respectively. The appropriate utilization of these two proteins will support their potential as natural ingredients in various food systems. © 2024 Society of Chemical Industry.

In situ formation SiC nanowires on loofah sponge-derived porous carbon for efficient electromagnetic wave absorption

A lightweight, heterogeneous, three-dimensional network-structured composite has been meticulously developed with the specific goal of optimizing impedance matching and elevating electromagnetic wave absorption properties. SiC nanowires-carbon composites were synthesized through a novel process involving combined carbothermal reduction and chemical vapor deposition, utilizing loofah sponge as the foundational material. Accessible and cost-effective organosilane waste was applied as the silicon source. The resulting composites manifest exceptional electromagnetic wave absorption performance with a minimum reflection loss of − 46.34 dB and a wide effective bandwidth of 3.84 GHz at a thin thickness of 1.9 mm. Superior electromagnetic wave absorption is attributed to synergistic interplay of multiple interfacial polarizations, dipole polarization, conductive losses, and multiple reflections and scattering. This work presents an innovative pathway toward fabricating highly efficient electromagnetic wave-absorbing materials while effectively repurposing recycled waste.

Efficient Photocatalytic Activity over α-MnS/ZIF-67 p-n Junction: Revealing the Synergistic Effects of Exposed Crystal Facets and Built-in Electric Field Mechanism

In this investigation, we explored two series of composites comprising p-type α-MnS with selectively exposed {001} or {111} facets, coated with n-type ZIF-67 nanoparticles, to enhance the photocatalytic activity on Rhodamine B (RhB) degradation. The influence of the crystal facet orientation and the p-n junction on the photocatalytic efficacy was also well studied. The α-MnS/ZIF-67 composites displayed enhanced separation of charge carriers and superior light absorption capabilities, benefiting for efficient photocatalysis. The composites with cubic α-MnS morphology exhibited a pronouncedly higher photocatalytic activity relative to those with octahedral α-MnS morphology. The composition of α-MnS with ZIF-67 constructed the formation of a p-n junction with build-in electric field, extending the response into the visible region and promoting the mobility of charge carriers, thereby improving the photocatalytic performance. Our findings revealed that superoxide radicals (O2-) were the major reactive species in the photocatalytic degradation process. This study contributes novel insights into the development of high-performance and stable metal-organic framework (MOF)-based photocatalysts through the crystal facet engineering and the construction of p-n junctions.

Bidirectional "Win-Win": Asymmetrical Nanobowl-Coupled Aggregation-Induced Emissive Nanosilicon-Enhanced Immunochromatographic Strips for the Ultrasensitive Detection of Salmonella typhimurium.

The lack of nanoprobes with an efficient signal response and overlook of cooperation between nanoprobes can be responsible for the unsatisfactory analytical performance of immunochromatographic strips (ITSs). Herein, asymmetrical nanobowl-confined innumerable gold nanoparticles (AuNPs) (AuNPs@AFRNBs) to enhance the light absorption are developed for quenching the fluorescence of aggregation-induced emissive (AIE) nanosilicons, which is used for the construction of a bidirectional complementary-enhanced ITS (BC-ITS) to ultrasensitively detect Salmonella typhimurium (S. typhimurium). Briefly, density functional theory-screened AIEgens with highly fluorescent brightness are confined in nanosilicons, and the nanoconfinement has improved the fluorescent brightness by 6.78-fold compared to the free AIEgens. Moreover, the substituent group effect has also enhanced the fluorescence of the prepared fluorescent nanosilicon by 10,000-fold in ITSs. By virtue of the superior light absorption of AuNPs@AFRNBs, the BC-ITS exhibits a bidirectional "win-win" performance for the sensitive monitoring of S. typhimurium: a "turn-on" mode with a high-brightness colorimetric response and an inverse "turn-off" fluorescence response, whose limits of detection are 364 and 302 CFU mL-1, respectively, which is approximately 100-fold more sensitive than the traditional AuNPs-ITS. Furthermore, the BC-ITS can be successfully used to identify S. typhimurium in milk, illustrating the superiority of the developed BC-ITS in point-of-care diagnosis.

Fabrication of hollow Fe3O4 microspheres encapsulated by single-walled carbon nanohorns for high-performance microwave absorption

Due to the increasingly serious electromagnetic radiation and pollution problems, it is urgent to develop high-performance electromagnetic wave absorbing materials. Herein, the hollow Fe3O4 microspheres encapsulated by single-walled carbon nanohorns (H-Fe3O4@SWCNHs) have been synthesized via facile solvothermal approach. The obtained H-Fe3O4@SWCNHs composite exhibits a unique hollow core-shell structure and superior microwave absorption performance. When the matching thickness is 2.0 mm, the composite shows a minimum reflection loss value of −42.2 dB at 13.6 GHz and a maximum effective absorption broadband value of 6.2 GHz covering from 11.8 to 18 GHz. The excellent microwave absorption performance of the H-Fe3O4@SWCNHs composite is mainly attributed to the unique hollow core-shell structure, optimal impedance matching, and synergistic effects of dielectric loss and magnetic loss. Therefore, the present work provides a new kind of ideal microwave absorbing material with light weight, thin thickness, wide bandwidth and strong absorption capability for high-performance microwave absorption.

Development of κ-carrageenan-based transparent and absorbent biodegradable films for wound dressing applications

Wound healing remains a critical challenge in healthcare, requiring advanced wound dressings with superior properties like transparency, absorbency, and biocompatibility. However, gaps exist in the use of marine-derived biopolymers for sustainable dressings. This study addresses this gap by combining κ-carrageenan (KC) with polyvinyl pyrrolidone (PVP) to develop transparent and absorbent biodegradable films through solvent casting and lyophilization techniques. Lyophilized films exhibited superior absorbency (9.17 g/cm2) and moisture management, with a water vapour transmission rate of 3990.67 g/m2/24 h, while solvent-cast films showed 78 % transmittance, enabling wound visualization. Mechanical testing revealed high tensile strength (31.5 MPa) and folding endurance (410 folds), ensuring durability. In vitro bactericidal assays confirmed efficacy against MRSA and E. coli, and in vivo tests on Wistar rats showed complete wound healing within 16 days with 91.1 % closure, outperforming untreated controls (76.7 %). This is the first study to explore lyophilized KC-PVP films for wound dressing applications, demonstrating potential for drug release, absorbency, and biodegradability. The innovative combination of biopolymers and fabrication techniques offers a sustainable, high-performance solution for wound care.

Design and Analysis of a 3D Frictional Mechanical Metamaterial for Efficient Energy Dissipation

AbstractThis study introduces a novel frictional mechanical metamaterial composed of a central hexagon or re‐entrant honeycomb frame, a lower section with four tapered columns, and an upper portion with a blade shape. When subjected to an external uniaxial force, the 3D structure of the metamaterial utilizes sliding interactions to dissipate frictional energy. The mechanical properties of the proposed metamaterial, such as load‐displacement relationships, hysteresis area, and peak force, can be fine‐tuned by adjusting geometric parameters and constituent materials. Extensive analysis is conducted through experimental compression tests, finite element (FE) simulations, and theoretical modeling. Comparative assessments of the metamaterial's energy dissipation performance demonstrated a good agreement between experimental and simulation results, with minor variations observed for deeper compression cycles. The proposed metamaterial offers the potential for superior elastic energy absorption and dissipation, making it a promising solution for applications requiring repeated energy dissipation or damping under cyclical loads while maintaining a lightweight profile.

3D printing of biomimetic liquid crystal elastomers with enhanced energy absorption capacities

Spider dragline silks are noted for their unmatched toughness, which arises from their unique primary structure. However, the underlying mechanisms of this toughness have seldom been verified using synthetic structural materials. Liquid crystal elastomers (LCEs) are polymer networks with mechanical properties bearing high resemblances to those of spider silks, and are ideal material for mimicking the primary structure of spider silk and revealing its toughing mechanisms. This study introduces a LCEs-based energy absorption structure that mimics the primary structure of spider dragline silks via 3D printing method. This LCEs-based biomimetic structure offers superior toughness and energy absorption capabilities with a damping capacity of 90%, significantly surpassing that of both artificial and biological viscoelastic materials. We successfully demonstrated that the biological primary structure provides the highest energy absorption capacity than other structures. This superior energy absorption capability was examined through hysteresis tests and then validated through intuitive ball free-falling tests. The work will illuminate a new pathway in the development of kinetic energy buffering and absorption materials.

Light‐Assisted Polyproton Dissociated PAAm‐PA Hydrogel‐Based Moisture‐Driven Electricity Generator with a Broad Operating Range

AbstractDue to its widespread availability and spontaneity, moisture electricity generation (MEG) holds unique advantages in self‐powered systems. However, it faces challenges, including the limitations of relying on a single kind of power generation and insufficient output performance. Inspired by the mechanisms of water absorption of plants, this paper explores a light‐moisture coordinated electricity generating hydrogel (L‐MEGH) device with flexible, scalable, and highly efficient energy conversion performance, which is obtained through the UV polymerization of hydrophilic acrylamide (AAM) and phytic acid (PA) in the presence of photosensitizers. The obtained hydrogel demonstrates superior moisture absorption and remarkable electricity generation stability across a range of humidity conditions. Notably, the open‐circuit voltage (Voc) of the L‐MEGH increased from 0.675 to 0.838 V after the addition of photosensitizers (Erythrosin B, E) (the significant enhancement, up to 24%), and the short‐circuit current (Isc) reaching 635.543 µA. This L‐MEGH can realize stable electrical output even under extreme temperatures, producing 0.5 V at −20 °C for 45 h. The scalable L‐MEGHs (connected on‐demand in series/parallel) can power various commercial electronics, including nighttime illumination, mobile phones, and health monitoring sensors. This work pioneers a sustainable power generation pathway capable of enhancing performance through the hybrid collection of multiple natural energy sources.

Compressive Mechanical and Heat Conduction Properties of AlSi10Mg Gradient Metamaterials Fabricated via Laser Powder Bed Fusion

Metamaterials are defined as artificially designed micro-architectures with unusual physical properties, including optical, electromagnetic, mechanical, and thermal characteristics. This study investigates the compressive mechanical and heat transfer properties of AlSi10Mg gradient metamaterials fabricated by Laser Powder Bed Fusion (LPBF). The morphology of the AlSi10Mg metamaterials was examined using an ultrahigh-resolution microscope. Quasi-static uniaxial compression tests were conducted at room temperature, with deformation behavior captured through camera recordings. The findings indicate that the proposed gradient metamaterial exhibits superior compressive strength properties and energy absorption capacity. The Gradient-SplitP structure demonstrated better compressive performance compared to other strut-based structures, including Gradient-Gyroid and Gradient-Lidinoid structures. With an apparent density of 0.796, the Gradient-SplitP structure exhibited an outstanding energy absorption capacity, reaching an impressive 23.57 MJ/m3. In addition, heat conductivity tests were performed to assess the thermal resistance of these structures with different cell configurations. The gradient metamaterials exhibited higher thermal resistance and lower thermal conductivity. Consequently, the designed gradient metamaterials can be considered valuable in various applications, such as thermal management, load-bearing, and energy absorption components.

Investigation of the effect of autoclave aging on polyurethane foams with low VOC content

Six flexible polyurethane foam recipes using low VOC additives were formulated and the prepared samples were analysed for their mechanical and acoustic properties pre and post autoclave aging. The results were compared with a reference foam comprising traditional additives. Promising results were obtained, particularly in acoustic performance, with two formulations (W2, W3) exhibiting superior sound absorption compared to the reference sample. However, after the autoclave aging the value of the sound absorption coefficient drops suddenly in a given frequency range, which may also indicate the degradation of the cell structure. The compressive strength of the samples were lower in case of four out of six samples, which can be due to their lower density. Adjustments in foaming reaction could potentially mitigate this issue. After the autoclave aging the compressive strength significantly reduced in all cases including the reference sample, which indicates that when the foams are utilized in wet environments for extended periods of time they cannot be further used for bearing applications.

Quasi static and dynamic energy absorption characteristics of silicon carbide reinforced resin based on triply periodic minimal surface structures

AbstractSilicon carbide (SiC)‐resin composites with porous structures exhibit excellent energy absorption characteristics. In this study, three types of triply periodic minimal surface (TPMS) structures (Schwarz primitive, Schwarz diamond, and Schwarz I‐graph‐wrapped (IWP)) were fabricated using the digital light processing (DLP) technique. Under static compression, the TPMS structures mainly fracture at the four ends of the X crossband. The SiC‐reinforced resin exhibited superior specific energy absorption in quasistatic compression performance compared with the same structure constructed of metal at the same density. Moreover, the transient impacts under dynamic strain rates did not cause significant irregular or asymmetric shear damage to the structure. The dynamic energy absorption of SiC‐reinforced resin with a primitive structure was relatively superior to that of the IWP and diamond structures. Therefore, the TPMS structure of the 5 wt.% SiC‐resin composite possesses significant energy absorption characteristics and can be extended for applications in aerospace.Highlights SiC reinforced resin exhibits superior specific absorption energy in quasi‐static compression performance. The yield strength of the static compression of the primitive structure is averaging nearly 17 MPa. The dynamic energy absorption of SiC reinforced resin with primitive structure is relatively superior between 65.68 and 71.63 J/g. The TPMS structure of 5 wt.% SiC/resin possesses significant energy absorption characteristics.

Enhanced Crashworthiness Parameters of Nested Thin-Walled Carbon Fiber-Reinforced Polymer and Al Structures: Effect of Using Expanded Polypropylene Foam

The in-plane loading conditions of carbon fiber/epoxy composite (CFRP) and aluminum nested-tube-reinforced expanded polypropylene (EPP) blocks were empirically examined. This study used crashworthiness metrics to estimate the best design configuration under quasi-static loading rates. The experimental phase began with lateral loading testing of single and nested aluminum and CFRP specimen. In-plane crushing experiments were performed on EPP foam blocks reinforced with nested tubes. Both single and nested aluminum tubes had comparable force–response curves and maintained their load-bearing capacity throughout testing. Despite a load-carrying capacity drop above a particular displacement threshold, the CFRP specimens had superior specific energy absorption (SEA) values due to their lightweight nature. The triple-tube nested specimens with two smaller tubes exhibited the best SEA results (1.72 and 1.88 J/g, respectively, for the aluminum and CFRP nested samples). During concurrent tube deformation, the nested samples showed a synergistic connection that increased energy absorption, especially in the EPP foam blocks with reinforced tubes. The study also examined the effects of building nested specimens with aluminum exterior tubes and CFRP inner tubes, and vice versa. This method showed that CFRP tubes within aluminum outer tubes lowered specimen weight (from 93.1 g to 67.7 g) and energy absorption (from 160.2 J to 153.3 J). However, the weight reduction outweighed the energy absorption, increasing SEA values for certain composite material configurations (from 1.72 J/g to 2.26 J/g).

Numerical Investigation of Solar Collector Performance with Encapsulated PCM: A Transient, 3D Approach

This study presents a comprehensive numerical investigation into the thermal performance of solar collectors integrated with encapsulated phase change materials (PCMs) using a transient three-dimensional (3D) approach. The performance of two distinct PCMs—paraffin wax and RT60—was evaluated under varying operational conditions, including seasonal variations, inlet pipe velocities, and inlet temperatures. The results indicate that paraffin wax exhibits a higher peak temperature, reaching approximately 360 K, compared to RT60’s peak of 345 K, making paraffin wax more effective for consistent thermal energy storage. Paraffin wax also maintained higher fluid fractions, with a maximum of 0.9 in summer, indicating superior heat absorption and retention capabilities. In contrast, RT60 demonstrated a quicker phase transition, fully liquefying at a lower fluid fraction, which is advantageous for rapid heat release. Seasonal variations significantly impacted system efficiency, with the highest efficiency observed in June at 365 K and the lowest in December at 340 K. The study also found that lower inlet velocities (e.g., 0.25 L/s) significantly improved heat retention, resulting in higher outlet temperatures, while increasing the inlet temperature from 290 K to 310 K led to a marked increase in outlet temperatures throughout the day. These findings underscore the importance of optimizing PCM selection, inlet velocity, and temperature in enhancing the performance of solar thermal systems, offering quantitative insights that contribute to the development of more efficient and reliable renewable energy solutions.

Transverse energy absorption performance of sandwich tubes with various origami foldcores

Nowadays, composite sandwich tubes are extensively utilized in the civil and aerospace industries due to their superior strength-to-weight mechanical properties. Origami-based core offers a large enhancement of the mechanical properties, yet little study research focuses on the effect of various foldcore configurations on the transverse mechanical properties of sandwich tubes, necessitating the design method for applications. This study introduces an innovative approach by incorporating origami into the composite sandwich core to enhance the transverse energy absorption capacity. The quasi-static transverse mechanical properties of carbon fibre-reinforced polymer (CFRP) sandwich tubes with foldcores are studied under three-point bending-like local compression and transverse structural compression. A systematic geometric design framework and numerical modelling technique are provided. By integrating finite element analysis and experiments, the research investigates the effects of various origami foldcore configurations and geometric parameters on transverse energy absorption capacity. The experiment setup is provided by sandwich tubular specimens with a full-diamond configuration as the foldcore. The cylindrical tubes (foldcore) of the sandwich structures were manufactured using four plies [0°]4 of T700 (T300) woven CFRP with the hot press moulding (vacuum bag using female and male moulds) technique respectively. Then, the parametric study and damage mode analysis of eight different foldcore patterns (axial Miura, circumferential Miura, diamond, Kresling, and their curved-creased counterparts) were studied. The results showed the superior energy absorption performance of the sandwich tube with Miura-pattern foldcore over the origami-pattern counterparts, nested tube, and traditional honeycomb sandwich tube with CFRP or aluminium-made cores. Therefore, the structural parameters optimisation of the Miura pattern tube was carried out by the Response Surface method (RSM) and a design strategy for increasing the energy absorption capacity was found. The findings offer guidance for designing high-specific energy absorption tubular structures for future advanced engineering applications.

Multifunctional lignin-reinforced cellulose foam for the simultaneous removal of oils, dyes, and metal ions from water

Pollutants emitted by industry pose an emerging threat to ecosystems, human health and native species, which has attracted global attention. At present, most of the biomass-based water remediation materials suffer from the poor mechanical properties, complexity of the modification process, single function and low adsorption capacity. Therefore, a high-strength lignin/cellulose foam absorbent (LCMA) with super-hydrophilic surface was developed for wastewater treatment by using lignin as the skeleton to crosslink cellulose through sol-gel method. Combined with an abundance of reactive functional groups and a highly porous structure, LCMA demonstrated a superior absorption and removal performance for cationic dyes and heavy metal ions, with separation efficiencies exceeding 99.76 % for cationic dyes and 99.85 % for heavy metal ions. Further modification of LCMA by a facile method using polydopamine (PDA) and polyethyleneimine (PEI) imparted superhydrophilicity to the foams. The developed LCMA@PDA@PEI exhibited an impressive immiscible oil-water separation performance and emulsion separation performance (Separation efficiency >99.95 % for immiscible oil-water mixtures and >99.05 % for oil-in-water emulsions). With the capabilities of simultaneous removal for dyes, heavy metal ions and oil pollutants from water, LCMA holds a broad application prospect in the water remediation, especially in the treatment of polluted water with complex components.

Reliable comparison of multi-directional mechanical properties for biomimetic circle arc honeycombs

Abstract Compared to straight honeycombs, curved honeycombs derived from biomimetic strategies typically exhibit superior mechanical properties and a broader tunable range. Consequently, there has been a surge in research focusing on curved honeycombs. However, few studies have concurrently designed multiple honeycombs for reliable comparisons, and little attention has been given to isotropy. In this study, circle arc walls were introduced to replace the straight walls of five classical honeycombs, thereby creating representative curved honeycombs for analysis. The numerical modeling method in ANSYS software was validated by experimentally testing 3D printed specimens of circle arc honeycombs. At the same mass and under loading conditions in different directions, it was found that the Young's modulus, yield strength, Poisson's ratio, and energy absorption of circle arc hexagon (CAH), circle arc square (CAS), circle arc triangle (CAT), circle arc re-entrant (CAR), and circle arc double-V (CAD) were assessed. Both experimental and numerical results revealed that CAH demonstrates superior energy absorption while maintaining a high degree of isotropy, characterized by all isotropic factors below 0.1 in mechanical properties. Notably, CAD exhibits a Negative Poisson's ratio (NPR) effect across all loading directions. These results provide benchmarks for future studies on curved honeycombs and guide further research in this field.

Bending response and energy absorption of sandwich beams with combined reinforced auxetic honeycomb core

This study introduces a reinforced star-shaped auxetic honeycomb (RSSAH) sandwich beam, enhanced with hollow thin-walled tubes to improve bending resistance and energy absorption performance. The bending performance of the RSSAH is systematically investigated through quasi-static three-point bending tests and finite element numerical simulations. The findings suggest that when subjected to mid-span stress, the RSSAH displays both localized indentation and overall bending deformation, accompanied by notable negative Poisson’s ratio (NPR) impact under bending loads. Parametric studies are undertaken by numerical simulations to investigate the impact of compression position, auxetic angle, and face sheet thickness on the bending mode of the auxetic honeycomb sandwich beam. The analysis shows that the RSSAH can exhibit excellent bending performance and, at one of the compression positions, displays double-plateau stress characteristics. It is also found that altering key geometric parameters, such as the auxetic angle and panel thickness ratio, can greatly improve the bending capabilities of the RSSAH, achieving stable plastic deformation and high energy absorption. Finally, compared to star-triangle honeycomb (STH) sandwich beam, traditional reentrant honeycomb (RH) sandwich beam and star-shaped auxetic honeycomb (SSAH) sandwich beam, the RSSAH demonstrates superior bending performance and energy absorption capacity. This study offers insights and references for the development of innovative reinforced auxetic honeycomb sandwich beams.