Sunflower Straw Research Articles

Hydrochar from co-hydrothermal carbonization of sewage sludge and sunflower stover: Synergistic effects and combustion characteristics

This study carried out co-hydrothermal carbonization (Co-HTC) on sewage sludge (SS) and sunflower straw (SFS) at various ratios (1:0, 3:1, 1:1, 1:3, 0:1) to prepare hydrochar. The raw samples and produced hydrochar were characterized using ultimate analysis, proximate analysis, Brunauer-Emmett-Teller (BET), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The potential synergistic impact during the reaction process were analyzed. As the SFS ratio increased, the fuel ratio of hydrothermal carbons rose from 0.29 to 0.37, while the higher heating value (HHV) improved from 7.44 (MJ/kg) to 20.86 (MJ/kg). The co-hydrothermal synergistic effect resulted in enhanced the hydrochar yield, energy yield, carbon sequestration rate and organic retention rate. Compared to raw sample, the surface of hydrochar exhibits a rougher and more fragmented structure, with an increased number of microspheres and micropores, resulted in an increased specific surface area. Thermogravimetric analysis (TGA) demonstrated that, in comparison to HTC of sludge alone, the Co-HTC of SS with SFS enhances the ignition temperature and delays the completion of combustion. Therefore, Co-HTC with SFS is an effective method for converting SS into clean solid fuel for energy applications.

Preliminary hydrothermal treatment and steam explosion of cellulosic feedstock for the subsequent biotechnological transformation: A review

The use of renewable sources of cellulosic feedstock to produce high value-added products is a relevant issue. Cellulosic feedstock constitutes a natural matrix comprising cellulose (38–50 %), lignin (10–25 %), and hemicel-luloses (23–32 %). In order to break it down, pretreatment involving the removal of hemicelluloses and lignin is required. This process can change the chemical composition and structure of cellulose while increasing porosity. This review article provides an analysis of data on the hydrothermal treatment and steam explosion of cellulosic feedstock (sunflower straw, lawn grass, poplar sawdust, hay, reed, aspen, giant reed, silage, etc.) intended to convert it into substrates for the synthesis of biotechnological products (protein, biohydrogen, biogas, levulinic acid, methane, lactic acid, ethanol, and succinic acid). Hydrothermal treatment involves treating raw materials at 160–240 °С in water under high pressure. Pressure keeps water in a liquid state. During steam explosion, feedstock is treated with steam at a moderate temperature and pressure for a certain amount of time. Then, the pressure is rapidly released, and the fibers of cellulosic feedstock expand. The effectiveness of hydrothermal treatment and steam explosion depends both on the type of feedstock (chemical composition, solids concentration, and properties of solids) as well as on the conditions of hydrothermal treatment and steam explosion.

Design and Experiments of the Data Acquisition System for Bale Rolling Characteristic Parameters on a Large-Scale Round Bale Machine

The parameters of the roll characteristics of a large-scale round bale machine were collected in real time to investigate the bale rolling mechanism. This investigation develops a set of adaptable and highly integrated data acquisition systems for the bale rolling performance parameters of large-type round bale machines. A rolling experiment is conducted using sunflower straw as the material, and the power consumption and radial tension of the roller-round bale machine during the bale rolling process are studied. In the grass core formation stage, the round bale machine’s torque need was minimal, the radial tension of the bale remained nearly constant, and the bale chamber was primarily filled with loose sunflower straw. The motor torque and the straw bale’s radial tension both showed a tendency of gradual increase when the round bale machine was in the grass-filling stage. The motor torque and bale radial tension displayed a roughly linear trend of rapid rise as the sunflower straw continued to enter the rolling bale chamber; this was when the round bale machine was in the compressed bale rolling stage. When the power consumption of the round bale machine was measured using the data acquisition system during the test bench empty run and core-creation stage, the energy consumption comparison analysis produced a relative error of 5.8%. During the stage of bale rolling and compression, the data acquisition system monitored the power consumption of the round bale machine. The relative error was 9.5%. The data acquisition system of the round bale machine test bed has an accuracy of 90.5%–94.2% when measuring the machine’s power consumption, indicating that it is a stable and efficient system. This study provides a foundation for further research on intelligent the roller-round bale machine.

Enhanced phosphorus and potassium recovery through co-pyrolysis of nutrient-rich biomass feedstocks for engineered biochar production

Engineered biochars were produced via slow pyrolysis at 600 °C for 1 h from selected carbon-rich (diyar wood, sawdust, cotton stalk, sunflower straw, and banana stem) and nutrient-rich (eggshell, chicken bone, chicken manure, and sewage sludge) biomass residues with enhanced P and K recovery. Separate pyrolysis of both category feedstocks and co-pyrolysis of selected carbon-rich and nutrient-rich feedstocks mixed at 3:1 ratio was conducted. Higher biochar yield (41 %) was achieved in the co-pyrolysis of sewage sludge and sunflower stalk compared to average (38.5 %) of their separate pyrolysis. Moreover, increased K recovery (5.3 % to 19.5 %) and increased P recovery (1.8 % to 25.5 %) was achieved in biochar through co-pyrolysis of nutrient-rich and selected carbon-rich feed stocks compared with their separate pyrolysis. The chicken bone and sewage sludge can be ideal feedstocks for enhanced P and K recovery through their co-pyrolysis with carbon rich biomass such as banana stem or sunflower stalk.

Development and performance evaluation of sunflower straw cellulose ether ecological sand-fixing material

Sunflowers are widely cultivated as a cash crop in the Inner Mongolia Autonomous Region, China. However, due to the lack of efficient resource utilization techniques, most of the sunflower stalks are discarded. In the Hetao irrigation area, the problem of desertification has prompted the limited use of sunflower straw to construct physical sand barriers for windbreaks and sand stabilization. In response to this, this study focuses on synthesizing a cellulose ether sand-fixing material using sunflower straw, the primary agricultural waste in Denkou County, Hetao irrigation district. This material enhances the effective adhesion between sand grains, reduces porosity among loose sand grains, and inhibits sand grain movement. The findings from this study conclusively demonstrate that the sand-fixing materials under investigation meet international standards for mechanical properties. They effectively transform loose, unconnected sand grains into a state with strong adhesion properties.

Influence on the fermentation quality, microbial diversity, and metabolomics in the ensiling of sunflower stalks and alfalfa.

With the rapid development of the livestock industry, finding new sources of feed has become a critical issue that needs to be addressed urgently. China is one of the top five sunflower producers in the world and generates a massive amount of sunflower stalks annually, yet this resource has not been effectively utilized. Therefore, in order to tap into the potential of sunflower stalks for animal feed, it is essential to explore and develop efficient methods for their utilization.In this study, various proportions of alfalfa and sunflower straw were co-ensiled with the following mixing ratios: 0:10, 2:8, 4:6, 5:5, 6:4, and 8:2, denoted as A0S10, A2S8, A4S6, A5S5, A6S4, and A8S2, respectively. The nutrient composition, fermentation quality, microbial quantity, microbial diversity, and broad-spectrum metabolomics on the 60th day were assessed. The results showed that the treatment groups with more sunflower straw added (A2S8, A4S6) could start fermentation earlier. On the first day of fermentation, Weissella spp.dominated overwhelmingly in these two groups. At the same time, in the early stage of fermentation, the pH in these two groups dropped rapidly, which could effectively reduce the loss of nutrients in the early stage of fermentation.In the later fermentation period, a declining trend in acetic acid levels was observed in A0S10, A2S8, and A4S6, while no butyric acid production was detected in A0S10 and A2S8 throughout the process. In A4S6, butyric acid production was observed only after 30 days of fermentation. From the perspective of metabolites, compared with sunflower ensiling alone, many bioactive substances such as flavonoids, alkaloids, and terpenes are upregulated in mixed ensiling.

Impacts of Maize and Sunflower Straw Implementations on Selected Physical and Mechanical Properties of Clay Soil

ABSTRACT The management of plant wastes and the development of soil quality characteristics have a key role in ensuring the harmony of the agriculture cycle with the environment. By adding the straw of plants directly to the soil as a source of organic matter, time poor soil quality characteristics can be improved. In the study, which was planned as a pot experiment, the effects of increasing the addition of sunflowers straw and maize straw by the increased proportions to clay soil. For this purpose, sunflower and maize harvest residue was added to the soil in 0% control (C), 0.5% (SS0.5 and MS0.5), 1% (SS1 and MS1), 2% (SS2 and MS2), and 4% (SS4 and MS4). Compared to the C, the water stable aggregate value increased by approximately 2.2 and 2.5 times in SS4 and MS4 implementations, mean weight diameter values increased approximately 2.7 and 3.3 times, respectively. In SS4 and MS4 implementations, the available water capacity increased by 80% and 102% compared to the control, respectively, and the modulus of rupture values were decreased by approximately 4.1–4.7 times. The 0.5% and 1% doses of straw implementations did not have great effects on the mechanical properties of the soils. According to the results of this study, 4% straw implementations it has been proven that the addition of SS and MS to the soil that by breaking them into small particles have great importance in rapidly increasing the physical quality of the soils and it can be used as an effective agricultural method.

Low-cost, superhydrophobic, flame-retardant sunflower straw-based xerogel as thermal insulation materials for energy-efficient buildings

Low cost, low energy consumption, and environment-friendly novel thermal insulation materials are highly attractive for energy-efficient buildings. However, traditional petroleum-based foams and aerogel require complicated processing, high cost, and non-degradability, which limit their sustainable development and application. Herein, multifunctional robust sunflower straw-based xerogels as thermal insulation materials are fabricated by simply filtrating and drying under ambient pressure without any extraction processing, due to sunflower straw raw materials with high content of cellulose. With the addition of KH550 and SiO2 nanoparticles, the obtained sunflower straw-based xerogels exhibit excellent thermal insulation (0.0469 W/(mK)), superior superhydrophobicity (water contact angle (WCA) = 153.2°), remarkable fire resistance, high mechanical property. These advanced properties make it an ideal thermally insulation material for diversified applications in harsh environments.

Interference effect of configuration parameters of vertical sand-obstacles on near-surface sand transport

This study investigates the impacts of height (H) and porosity (P) on the structural properties of wind-driven sand flux in vertical sunflower straw sand-obstacles. We conducted an experiment on sand transport within barriers of various configurations within a 1 m proximity to the surface. In tandem, we monitored wind velocity and direction within the barriers, analyzed total sand transport rate, sand-blocking effects, and cumulative sediment transport rate heights for various parameter configurations, and devised a best sand transport flux model for use within the sand-obstacle. The efficacy of vertical sunflower stalk sand-obstacles in mitigating sand movement has been demonstrated to fall within the range of 37.26%–92.31%. This study reveals a significant correlation between barrier height and porosity in achieving this effect (p < 0.05). High and densely configured sand-obstacles lead to an accumulation of intercepted sand material in front of the front row of the sand-obstacle. In contrast, low and sparsely arranged sand-obstacles exhibit a delayed state of sand material accumulation. Furthermore, with an increase in the height of the obstacle and a decrease in porosity, there is a diminishing trend in the sand transport rate within the obstacle. Concurrently, the height of sand transport within the barrier exhibits an upward trend. A three-parameter exponential function has been employed to more precisely simulate the wind-sand flow structure characteristics within a 1-m height range of the barrier. These research findings contribute to an enhanced understanding of the impact of different vertical sand-obstacle configurations on near-surface wind-driven sand transport patterns in active desert areas. Moreover, they furnish both theoretical underpinnings and practical guidance for the scientific configuration of vertical sand-obstacles.

Biomass waste derived heteroatom doping porous carbon sheets for high performance supercapacitor

Porous carbon sheets exhibit a big open flat layer with large surface area, short ion transfer distance, which has attracted massive research as electrode materials for supercapacitors. Here, O, N, and P co-doped porous carbon sheets (ONPC) were developed by one-step activation way using sunflower straw as the carbon source, NH4H2PO4 as phosphorus the source, and nitrogen source, and then activated by KHCO3. Benefiting from the suitable specific surface area and massive O (13.98 at%), N (7.43 at%), and P (0.81 at%) functional groups, the ONPC-700 electrode exhibits a specific capacitance of 340 F g−1 at 0.5 A g−1, superior electrochemical stabilization with the capacitance retention rate of 100.5% after 10,000 cycles. More interestingly, the assembled symmetric supercapacitor (ONPC-700//ONPC-700) achieves an energy density of 22.0 Wh Kg−1 and superior electrochemical stabilization. The above excellent results indicate that this paper offers a feasible and simple strategy for preparing biomass-based heteroatom doped porous carbon sheets for supercapacitors.

Sunflower straw ash as an alternative activator in alkali-activated grouts: A new 100% waste-based material

Alkali-activated grouts (AAGs) are increasingly used to replace ordinary portland cement owing to their several advantages. The mechanical properties and environmental aspects of AAGs are affected by the type of activator. In this study, the effects of sunflower stalk ash (SSA) and commercial alkaline reagents on the mechanical properties, microstructures, and CO2 emissions of geopolymer grouts were investigated for the first time using blast furnace slag and black rice husk ash as precursors. The results indicated that the potassium and calcium salts in the SSA promoted the formation of C(K)-A-S-H and C–S–H. The compressive strength of the SSA-activated grouts was higher than that of the slurry prepared using commercial products (24.88 vs. 11.59 MPa). Using SSA instead of commercial reagents can reduce kg CO2-eq/t powder by 84.4 %.

Enhancing enzymatic saccharification of sunflower straw through optimal tartaric acid hydrothermal pretreatment

Sunflower straw, a usually neglected and abundant agricultural waste, has great potential for contributing to environmental protection realizing its high-value of valorization if utilizing properly. Because hemicellulose contains amorphous polysaccharide chains, relatively mild organic acid pretreatment can effectively reduce its resistance. Through hydrothermal pretreatment, sunflower straw was pretreated in tartaric acid (1 wt%) at 180 °C for 60 min to enhance its reducing sugar recovery. After tartaric acid-assisted hydrothermal pretreatment, 39.9% of lignin and 90.2% of xylan were eliminated. The reducing sugar recovery increased threefold, while the solution could be effectively reused for four cycles. The properties of more porous surface, improved accessibility, and decreased surface lignin area of sunflower straw were observed through various characterizations, which explained the improved saccharide recovery and provided a basis for the mechanism of tartaric acid-assisted hydrothermal pretreatment. Overall, this tartaric acid hydrothermal pretreatment strategy greatly provided new impetus for the biomass refinery.

Enhancing enzymatic hydrolysis of waste sunflower straw by clean hydrothermal pretreatment

Hydrothermal pretreatment is an effective way to change the lignocellulose structure and improve its saccharification. An efficient hydrothermal pretreatment of sunflower straw was conducted when the severity factor (LogR0) was 4.1. 58.8% of xylan and 33.5% of lignin were removed at 180 °C for 120 min with a solid-to-liquid ratio of 1:15. A series of characterizations (such as X-ray diffraction, Fourier Transform infrared spectroscopy, scanning electron microscopy, chemical component analysis, cellulase accessibility) proved that hydrothermal pretreatment destroyed sunflower straw surface structure, enlarged its pores, and enhanced the accessibility to cellulase (371.2 mg/g). After the enzymatic saccharification of treated sunflower straw for 72 h, 68.0% yield of reducing sugar and 61.8% yield of glucose were achieved, and 3.2 g/L xylo-oligosaccharide was obtained in the filtrate. Overall, this easy-to-operate and green hydrothermal pretreatment could effectively destroy the surface barrier of lignocellulose, help remove lignin and xylan, and increase the enzymatic hydrolysis efficiency.

Towards fossil-carbon free buildings: Production and environmental performance of innovative sound absorbing panels made from sunflower straw

Towards fossil-carbon free buildings: Production and environmental performance of innovative sound absorbing panels made from sunflower straw

Biomimetic Guided Bi2WO6/Bi2O3 Vertical Heterojunction with Controllable Microstructure for Efficient Photocatalysis

To bridge the technical gap of heterojunction induction control in conventional semiconductor photocatalysts, a method of regulating the growth of heterojunctions utilizing biomimetic structures was designed to prepare a series of Bi2WO6/Bi2O3 vertical heterojunction nanocomposites for the disposal of environmentally hazardous tetracycline wastewater difficult to degrade by conventional microbial techniques. Porous Bi2O3 precursors with high-energy crystalline (110) dominant growth were produced using the sunflower straw bio-template technique (SSBT). Bi2WO6 with a (131) plane grew preferentially into 2.8 to 4 nm pieces on the (110) plane of Bi2O3, causing a significant density reduction between Bi2WO6 pieces and a dimensional decrease in the agglomerated Bi2WO6 spheres from 3 μm to 700 nm since Bi2WO6 grew on the structure of the biomimetic Bi2O3. The optimal 1:8 Bi2WO6/Bi2O3 coupling catalyst was obtained via adapting the ratio of the two semiconductors, and the coupling ratio of 1:8 minimized the adverse effects of the overgrowth of Bi2WO6 on degradation performance by securing the quantity of vertical heterojunctions. The material degradation reaction energy barrier and bandgap were significantly reduced by the presence of a large number of vertical heterojunction structures, resulting in a material with lower impedance and higher electron-hole separation efficiency; thus, the degradation efficiency of 1:8 Bi2WO6/Bi2O3 for tetracycline hydrochloride reached 99% within 60 min. In conclusion, this study not only successfully synthesized a novel photocatalyst with potential applications in water pollution remediation but also introduced a pioneering approach for semiconductor-driven synthesis.

Preparation of activated carbon from sunflower straw through H3PO4 activation and its application for acid fuchsin dye adsorption

With the development circular economy, the use of agricultural waste to prepare biomass materials to remove pollutants has become a research hotspot. In this study, sunflower straw activated carbon (SSAC) was prepared by the one-step activation method, with sunflower straw (SS) used as the raw material and H3PO4 used as the activator. Four types of SSAC were prepared with impregnation ratios (weight of SS to weight of H3PO4) of 1:1, 1:2, 1:3, and 1:5, corresponding to SSAC1, SSAC2, SSAC3, and SSAC4, respectively. The adsorption process of acid fuchsin (AF) in water using the four types of SSAC was studied. The results showed that the impregnation ratio significantly affected the structure of the materials. The increase in the impregnation ratio increased the specific surface area and pore volume of SSAC and improved the adsorption capacity of AF. However, an impregnation ratio that was too large led to a decrease in specific surface area. SSAC3, with an impregnation ratio of 1:3, had the largest specific surface area (1 794.01 m2/g), and SSAC4, with an impregnation ratio of 1:5, exhibited the smallest microporosity (0.052 7 cm3/g) and the largest pore volume (2.549 cm3/g). The adsorption kinetics of AF using the four types of SSAC agreed with the quasi-second-order adsorption kinetic model. The Langmuir isotherm model was suitable to describe SSAC3 and SSAC4, and the Freundlich isotherm model was appropriate to describe SSAC1 and SSAC2. The result of thermodynamics showed that the adsorption process was spontaneous and endothermic. At 303 K, SSAC4 showed a removal rate of 97.73% for 200-mg/L AF with a maximum adsorption capacity of 2 763.36 mg/g, the highest among the four types of SSAC. This study showed that SAAC prepared by the H3PO4-based one-step activation method is a green and efficient carbon material and has significant application potential for the treatment of dye-containing wastewater.

Improving enzymatic hydrolysis of sunflower straw pretreated by deep eutectic solvent with different carboxylic acids as hydrogen bond donors

Improving enzymatic hydrolysis of sunflower straw pretreated by deep eutectic solvent with different carboxylic acids as hydrogen bond donors

Efficient Removal of Heavy Metals from Contaminated Sunflower Straw by an Acid-Assisted Hydrothermal Process.

The removal of heavy metals is crucial to the utilization of contaminated biomass resources. In this study, we report an efficient process of hydrothermal conversion (HTC) of sunflower straw (Helianthus annuus L.) to remove heavy metals. The effect of different HTC temperatures and concentrations of HCl additives on heavy metal removal efficiency was investigated. The results revealed that increasing the temperature or concentration of HCl promoted the transfer of heavy metals from hydrochar to liquid products during HTC. The heavy metals removed to the liquid products included up to 99% of Zn and Cd, 94% of Cu, and 87% of Pb after hydrothermal conversion with a temperature of 200 °C and HCl 2%. The species of heavy metals in hydrochars converted from unstable to stable with an increase in temperature from 160 °C to 280 °C. The stable fractions of heavy metals in the acidic condition decreased as the acid concentration increased. This aligns well with the high transfer efficiency of heavy metals from the solid phase to the liquid phase under acidic conditions. The FTIR indicated that the carboxy and hydroxy groups decreased significantly as the temperature increased and the concentration of HCl increased, which promoted the degradation of sunflower straw. A scan electron microscope showed that the deepening of the destruction of the initial microstructure promotes the transfer of heavy metals from hydrochars to liquid phase products. This acid-assisted hydrothermal process is an efficient method to treat biomass containing heavy metals.

Assessment of the potential of mustard by-products for fertilizer

The purpose of this work was to evaluate the effectiveness of using mustard harvest residues as fertilizer. Laboratory, measuring-weighing and mathematicalstatistical methods were used in the research. With the development of research on bioenergy, a number of authors propose to use by-products (straw and other residues) for the production of biofuel. However, it has been proven by plant scientists that plowing of crop residues ensures the replenishment of soil organic matter reserves, mineral nutrition elements and the reduction of the cost of grown products due to the reduction of the amount of applied mineral fertilizers. It was found that among the studied oilseed crops, the largest biomass potential was obtained from the cultivation of sunflower and soybean, the smallest – black mustard. But, even with a mustard seed yield of 1.52 t/ha in terms of straw, 30.4 kg/ha of potassium can be obtained from each hectare, or 1.6 times more than from soybean straw, as well as 21.28 kg/ha nitrogen and 7.6 kg/ha of phosphorus. When using black mustard straw for biofuel, the yield of which nutrients is the lowest compared to other oil crops to replenish the balance, it will be necessary to apply 54.6 kg/ha of mineral fertilizers in the amount of 52.5 thousand hryvnias/ha. The largest additional costs for mineral fertilizers will be more than UAH 240,000/ha for the extraction of sunflower straw for biofuel, even with its yield of 2.0 t/ha. Therefore, in the conditions of shortage of organic fertilizers in modern agriculture, crop residues can successfully replace the lack of organic fertilizers and replenish soil reserves with elements of mineral nutrition. Therefore, with a significant increase in mineral fertilizers and a reduction in the use of organic fertilizers, it is advisable to plow the by-products of mustard and other agricultural crops, and not use them for the production of biofuel, which will ensure the replenishment of the soil with mineral nutrients and reduce the cost of production by reducing the amount of applied mineral fertilizers. Key words: productivity, gross collection, yield of straw, nutrients, mineral fertilizers.

The Influence of Different Crop Mulches on Weed Infestation, Soil Properties and Productivity of Wheat under Conventional and Conservation Production Systems.

Pakistan and other South Asian countries rely on wheat for human nutrition. However, wheat yield is declining in the region due to several biotic and abiotic constraints. Weeds are among the major factors responsible for yield decrease and farmers manage them by intensive tillage practices. Several studies have investigated the impact of various tillage practices on weed management in wheat. However, weed suppression abilities of different mulch types are rarely tested. This three-year (2019-20, 2020-21 and 2021-22) study investigated the impact of different mulch types (prepared from different crops) on weed infestation, soil properties and productivity of wheat under conventional and conservation production systems at three locations (Multan, Hafizabad and Faisalabad) in Punjab, Pakistan. The mulches included in the study were cotton sticks mulch, mungbean straw mulch, sorghum straw mulch, rice straw mulch, sunflower straw mulch, plastic mulch, and no mulch (as control). The production systems opted for wheat cultivation were conventionally tilled wheat (CTW), zero-tilled wheat (ZTW) and zero-tilled wheat sown with happy seeder machine (HSW). The CTW resulted in the lowest soil bulk density and the highest soil porosity after wheat harvest, while ZTW behaved oppositely. Similarly, incorporation of crop mulches resulted in the highest soil porosity and the lowest soil bulk density, while no-mulch incorporation and plastic mulch recorded the highest bulk density and the lowest soil porosity. Regarding mulches by production systems' interaction, CTW with sorghum straw- and plastic mulches recorded the lowest weed density and biomass, while ZTW with no-mulch recorded the highest weed density and biomass at all locations. The CTW with mungbean straw- and plastic mulches resulted in the highest yield due to significant improvement in yield-related traits. However, ZTW with sorghum straw mulch and no-mulch resulted in the lowest wheat yield. Although sorghum straw mulch suppressed weed infestation, it negatively affected wheat growth. Economic analysis revealed that CTW with mungbean straw mulch resulted in the highest gross and net incomes and benefit:cost ratio (BCR), while the ZTW with rice straw- and sorghum straw mulches produced the lowest gross and net incomes and BCR at all locations. Therefore, mungbean straw mulch is a viable option to improve wheat productivity and net economic returns under different agro-climatic conditions of Punjab, Pakistan.