Subvisible Particles Research Articles

Mixing of a mAb Formulation in a New Magnetically Coupled Single-Use Mixing System: Key Learnings of Preliminary Experimental and Computational Evaluation

MilliporeSigma recently introduced a new magnetically coupled single-use mixing system (Mobius® Power MIX) for more efficient mixing of buffers and media in biopharmaceutical applications. Experimental and computational fluid dynamics (CFD) assessments were performed on the Power MIX 100 system to understand product quality impact, shear, and mixing efficiency. It was interesting to note slightly higher submicron (0.4-1 μm) and subvisible (1-54 μm) particle formation at the lower mixing speed (50 RPM) compared to higher mixing speeds (100/200 RPM). Mixing speed and time showed negligible impact on the other product quality attributes tested, including protein concentration, turbidity, general appearance, purity, and soluble aggregates. The CFD simulations provided useful information with respect to the impact of batch size (20-100 L), viscosity (2-50 cP), and impeller speed (100-300 RPM) on mixing time (mixing time ranged from 10 to 365 s) and shear (maximum shear rate was found to be localized around the impeller and it was about 30,260 s−1, whereas the average shear rate ranged from 4 to 36 s−1). Statistical analysis of the CFD results showed that natural-log transformation and quadratic fitting were found to be suitable statistical models to predict mixing time and shear within the design space of the parameters assessed in the present study.

Subvisible Particulate Contamination in Cell Therapy Products-Can We Distinguish?

Cell therapy products represent an exciting new class of medicinal products, which must be parenterally administered. Thus, compliance with parenteral preparation guidelines is required. One requirement for parenteral products is the characterization of particle contaminations. As cell-based products are turbid suspensions, containing particles, the cells, characterization and control of foreign particle impurities remain a challenge. Within this study, we evaluated a flow imaging microscopy method for the detection and characterization of subvisible particle contaminations in cell-based products. We found that flow imaging microscopy is a potential method where subvisible particle contaminations can be differentiated from the cells in cell therapy products.

Do bevacizumab solutions interact with silicone or polyurethane catheters during an infusion through implantable venous access ports?

This work aims to evaluate the possible impact of interactions between bevacizumab solutions and an implantable port equipped with a silicone or a polyurethane catheter after infusion through a complete infusion set-up in simulated use conditions. Physico-chemical and structural stability of bevacizumab solution was assessed by visual examination, subvisible particles counting, dynamic light scattering, size exclusion chromatography and ion exchange chromatography. Mechanical properties of the catheters were evaluated by measuring Shore A hardness, strain at break, strain at stress and Young's modulus. The physico-chemical surface state of the catheters was assessed by FTIR-ATR spectroscopy, scanning electron microscopy (SEM) and by water contact angle measurement. The analysis of the bevacizumab solution did not highlight any signs of instability or loss of active substance. Mechanical properties of both materials remained unchanged after the infusion. During material analysis, a decrease in water contact angle observed after infusion and was more pronounced for polyurethane catheters than for silicone, possibly due to bevacizumab adsorption or possible leachable extraction from the materials. Surface modifications were also noted at SEM. This study did not highlight any modifications that could alter the quality of the bevacizumab infusion, nor of the infusion catheter in polyurethane or silicone, despite a modification of surface hydrophilicity. Even if after a single infusion, implantable ports remained safe to use, they aim to be used for several infusion of various drugs during their lifetime, and further studies are needed to assess the impact of repeated infusions.

Shape Characterization of Subvisible Particles Using Dynamic Imaging Analysis.

Protein aggregates and subvisible particles (SbvP), inherently present in all marketed protein drug products, have received increasing attention by health authorities. Dynamic imaging analysis was introduced to visualize SbvP and facilitate understanding of their origin. The educational United States Pharmacopeia chapter <1787> emphasizes that dynamic imaging analysis could be used for morphology measurements in the size range of 4-100 μm. However, adequate morphology characterization, as suggested in the United States Pharmacopeia <1787> proposed size range, remains challenging as nonspherical size standards are not commercially available. In this study, a homogenous and well-defined nonspherical particle standard was fabricated and used to investigate the capabilities of 2 dynamic imaging analysis systems (microflow imaging (MFI) and FlowCAM) to characterize SbvP shape in the size range of 2-10 μm. The actual aspect ratio of the SbvP was measured by scanning electron microscopy and compared to the results obtained by dynamic imaging analysis. The test procedure was used to assess the accuracy in determining the shape characteristics of the nonspherical particles. In general, dynamic imaging analysis showed decreasing accuracy in morphology characterization for 5 μm and 2 μm particles. The test procedure was also capable to compare and evaluate differences between the 2 dynamic imaging methods. The present study should help to define ranges of operation for dynamic imaging analysis systems.

Part 2: Physicochemical characterization of bevacizumab in 2 mg/mL antibody solutions as used in human i.v. administration: Comparison of originator with a biosimilar candidate

The physicochemical properties of Avastin® manufactured in the USA (Originator USA) and in Europe (Originator EU) and ABX-BEV, a bevacizumab biosimilar drug product candidate produced by Apobiologix Inc., were characterized at a clinically relevant concentration of 2 mg/mL following dilution of the 25 mg/mL drug products with 0.9% NaCl. Measurements using 14 orthogonal analytical methods performed within 5 h after dilution showed good similarity of the three antibodies as regards secondary structure, conformation, aggregation properties, subvisible and visible particles. No significant protein aggregation was observed within 5 h at 24 °C in the 2 mg/mL bevacizumab solutions. The same solutions that were measured within 5 h after dilution were analyzed again after 24 h overnight refrigeration at 2–8 °C: all 2 mg/mL bevacizumab solutions showed an increase in the number and sizes of aggregates, especially the particles larger than 10 μm and 25 μm. The data show the very good similarity in the physicochemical properties of ABX-BEV with Originators USA and EU at a clinically relevant concentration.

Overcoming Challenges of Implementing Closed System Transfer Device Clinical In-Use Compatibility Testing for Drug Development of Antibody Drug Conjugates.

Closed system transfer devices (CSTD) are a supplemental engineering control designed to reduce occupational exposure of hazardous drugs and are currently implemented in accordance with evolving regulations. Owing to the novelty and complexity of these devices and their importance in clinical in-use testing, here we evaluated FDA-approved CSTD, assessing product quality through stability indicating assays to determine any drug product incompatibilities. Six devices were used in a simulated compounding and administration of a late-phase IgG1 antibody-drug conjugate (ADC) and the resulting samples were analyzed for visible and subvisible particle counts by light obscuration and micro-flow imaging, physical stability by size exclusion chromatography, and biological activities by relative potency. Potential challenges included improper fit of CSTD components, loss of product to void volume, and material incompatibility. Results showed compatibility of the ADC with the 6 CSTD evaluated. One CSTD introduced subvisible particles into the ADC during compounding that were identified through morphological assessment as silicone oil. This study highlights the importance of clinical in use testing with new devices and proposes strategies to mitigate the risk of drug product incompatibility with CSTD.

Framework Mutations of the 10-1074 bnAb Increase Conformational Stability, Manufacturability, and Stability While Preserving Full Neutralization Activity

The broadly neutralizing anti-HIV antibody, 10-1074, is a highly somatically hypermutated IgG1 being developed for prophylaxis in sub-Saharan Africa. A series of algorithms were applied to identify potentially destabilizing residues in the framework of the Fv region. Of 17 residues defined, a variant was identified encompassing 1 light and 3 heavy chain residues, with significantly increased conformational stability while maintaining full neutralization activity. Central to the stabilization was the replacement of the heavy chain residue T108 with R108 at the base of the CDR3 loop which allowed for the formation of a nascent salt bridge with heavy chain residue D137. Three additional mutations were necessary to confer increased conformational stability as evidenced by differential scanning fluorimetry and isothermal chemical unfolding. In addition, we observed increased stability during low pH incubation in which 40% of the parental monomer aggregated while the combinatorial variant showed no increase in aggregation. Incubation of the variant at 100 mg/mL for 6 weeks at 40°C showed a 9-fold decrease in subvisible particles ≥2 μm relative to the parental molecule. Stability-based designs have also translated to improved pharmacokinetics. Together, these data show that increasing conformational stability of the Fab can have profound effects on the manufacturability and long-term stability of a monoclonal antibody.

Rapid, quantitative determination of aggregation and particle formation for antibody drug conjugate therapeutics with label-free Raman spectroscopy

Lot release and stability testing of biologics are essential parts of the quality control strategy for ensuring therapeutic material dosed to patients is safe and efficacious, and consistent with previous clinical and toxicological experience. Characterization of protein aggregation is of particular significance, as aggregates may lose the intrinsic pharmaceutical properties as well as engage with the immune system instigating undesirable downstream immunogenicity. While important, real-time identification and quantification of subvisible particles in the monoclonal antibody (mAb) drug products remains inaccessible with existing techniques due to limitations in measurement time, sensitivity or experimental conditions. Here, owing to its exquisite molecular specificity, non-perturbative nature and lack of sample preparation requirements, we propose label-free Raman spectroscopy in conjunction with multivariate analysis as a solution to this unmet need. By leveraging subtle, but consistent, differences in vibrational modes of the biologics, we have developed a support vector machine-based regression model that provides fast, accurate prediction for a wide range of protein aggregations. Moreover, in blinded experiments, the model shows the ability to precisely differentiate between aggregation levels in mAb like product samples pre- and post-isothermal incubation, where an increase in aggregate levels was experimentally determined. In addition to offering fresh insights into mAb like product-specific aggregation mechanisms that can improve engineering of new protein therapeutics, our results highlight the potential of Raman spectroscopy as an in-line analytical tool for monitoring protein particle formation.

Application of ER Stress Biomarkers to Predict Formulated Monoclonal Antibody Stability.

For a therapeutic monoclonal antibody (mAb) to reach the clinic, the molecule must be produced at an appropriate yield and quality, then formulated to maintain efficacy and stability. The formation of subvisible particles (SVPs) can impact product stability and is monitored during formulation development; however, the potential of a mAb to form such species can be influenced throughout the whole bioprocess. The levels of intracellular endoplasmic reticulum (ER) stress perceived by Chinese hamster ovary (CHO) cell lines, the day of mAb harvest, and the relationship with subsequent product stability of two mAbs (denoted A and B), as determined by the SVP content after accelerated stability studies, are reported here. Here, it is shown that the propensity of mAb A to form SVPs can be predicted by transcript expression of biomarkers of cellular ER stress, heavy/light-chain transcript and polypeptide amounts, and harvest day. Further, mAb A material harvested on day 9 of culture was more stable, in terms of SVP formation, than material harvested on day 13. These data suggest that ER stress perceived by CHO cells can reflect the stability of a mAb, and that biomarkers of such stress could help define culture harvest time as a tool to control SVP formation in formulated mAbs.

Bevacizumab for Intravitreal Injection: Impact of Sub-Visible Particles on the Shelf-Life of Repackaged Bevacizumab.

Purpose: Bevacizumab (Avastin) is a humanized monoclonal antibody approved by the European Medicines Agency for the intravenous treatment of cancer. However, it is often used as an intravitreal injection for the treatment of macular degeneration or edema. For this purpose, bevacizumab is repackaged from glass vials into plastic syringes. The formation of particles during this compounding process as well as during storage is a source of concern. The aim of this study was to test the sub-visible particulate contamination in bevacizumab material, both in the glass vial and after repackaging into polycarbonate BD Luer-Lok™ syringes. Methods: Syringes with repackaged bevacizumab from 3 different compounding hospital pharmacies were tested for sub-visible particles at different time points during storage at 2-8°C. Results: The batches of bevacizumab starting product complied with the European Pharmacopoeia (Ph. Eur.) for small-volume parenterals. Repackaging into syringes led to an immediate increase in small particles. The number of particles ≥25 μm increased 1.3-fold, and the number of particles ≥10 μm increased 5-fold, respectively. Storage of up to 37 days did not lead to an additional increase in particle counts. All batches complied with the national criteria for particles in intravitreal solutions. Conclusions: Particle count increased due to the repackaging process, but no substantial increase was observed during storage. Formation of sub-visible particles does not impact the shelf-life of bevacizumab repackaged into BD Luer-Lok syringes.

Novel insights into the chemistry of an old medicine: A general degradative pathway for penicillins from a piperacillin/tazobactam stability study

Piperacillin is a broad spectrum beta-lactam antibiotic used in combination with tazobactam for hospital-related bacterial infections. The reconstituted solutions must respect the sub-visible and visible particles specifications. It was claimed that the reformulation containing EDTA/sodium citrate was able to control the formation of an insoluble impurity responsible for the formation of particulate matter observed using Ringer Lactate as diluent. The nature of the impurities formed during the degradative process of piperacillin/tazobactam combination has been herein investigated, by exploring the effect of added excipients and pH variations. The exact structure of the isolated dimeric impurity, the penicilloic acid-piperacillin dimer, was determined through complete characterization, allowing to propose a novel degradative general pathway for beta-lactam antibiotics. The presence of EDTA resulted unnecessary to contain the formation of the insoluble impurity, since the use of sodium citrate alone allowed to avoid this drawback. Finally, the proposed mechanism was successfully applied to the design of a novel, easy and high purity procedure for the synthesis of the acetylated penicilloic acid, known related substance of piperacillin.

Extended Stability of Reconstituted and Diluted SB3 (Trastuzumab Biosimilar) Assessed by Physicochemical and Biological Properties.

IntroductionStability information for the trastuzumab biosimilar SB3 is limited to 48 h at 2–8 °C for the reconstituted solution and 24 h at up to 30 °C for diluted solutions. Extended physicochemical stability and biological activity were assessed to evaluate the advanced preparation of reconstituted and diluted SB3.MethodsUnder controlled and aseptic conditions, the stability of reconstituted and diluted SB3 was evaluated using several assessments and according to the UK’s National Health Service guidance. Reconstituted SB3 was stored at 25 ± 2 °C with 60 ± 5% relative humidity for 3 days, and subsequently diluted SB3 (0.32–4 mg/mL) was stored in an infusion bag in the absence of light at 25 ± 2 °C with 60 ± 5% relative humidity for 28 days and 5 ± 3 °C for 28 days, respectively. Physicochemical stability (appearance, pH, protein concentration, size exclusion high-performance liquid chromatography, non-reducing capillary electrophoresis–sodium dodecyl sulfate, imaged capillary isoelectric focusing), biological activity (competitive inhibition binding assay to human epidermal growth factor receptor 2 by fluorescence resonance energy transfer, anti-proliferation assay), and properties with a potential safety impact (subvisible particulates, submicronic aggregation by dynamic light scattering) were determined.ResultsNo physicochemical instability signs or biological activity changes were observed for either reconstituted or diluted SB3 up to 28 days; all stability acceptance criteria were met. No major change was noted in the proportion of molecular weight variants (high molecular weight impurity, total purity) or relative percentages of acidic, main, and basic charge isoforms of the protein. No increases in particulates or aggregates in terms of a potential safety impact were noted.ConclusionThe physicochemical stability and biological activity of reconstituted and diluted SB3 are maintained for extended time periods beyond those denoted in the product labeling, which allows for advanced SB3 preparation and may reduce drug wastage and preparation time.FundingSamsung Bioepis Co., Ltd.

Nanobubbles in Reconstituted Lyophilized Formulations: Interaction With Proteins and Mechanism of Formation

Reconstitution of lyophilized disaccharide formulations results in the formation of nanosized air bubbles that persist in suspension for weeks. If proteins are present, interactions with nanobubbles may cause loss of monomeric protein and formation of subvisible particles. The goals of this work are to determine the mechanism(s) by which nanobubbles form in reconstituted lyophilized formulations and to develop strategies for reducing nanobubble generation. We hypothesize that nanobubbles are created from nanosized gas pockets within lyophilized solids, which become bubbles when the surrounding matrix is dissolved away during reconstitution. Nanosized voids may originate from small ice crystals formed within the concentrated liquid during freezing that subsequently sublime during drying. Nanobubble concentrations are correlated with the extent of mannitol crystallization during freezing. Nanosized ice crystals, induced by the release of water during mannitol crystallization, were responsible for nanobubble formation. The presence of trehalose or sucrose, in formulations with low mannitol concentrations, inhibited excipient crystallization during lyophilization and reduced nanobubble levels following reconstitution. Our results show a correlation between nanobubble formation and concentrations of insoluble IL-1ra aggregates, suggesting that minimizing nanobubble generation may be an effective strategy for reducing protein aggregation following reconstitution.

Size-dependent microbial diversity of sub-visible particles in a submerged anaerobic membrane bioreactor (SAnMBR): Implications for membrane fouling

Sub-visible particles, an often-overlooked fine particle (0.45–10 μm) with a size between sludge solids and soluble microbial products (SMP), have recently been identified as a critical foulant in anaerobic membrane bioreactors (AnMBRs), and our recent new insights into the size-fractionation and composition of sub-visible particles in AnMBRs have enabled fouling to be understood in more depth. Here, we investigated the microbial diversity of the sub-visible particles in three size fractions (i.e., 5–10, 1–5, and 0.45–1 μm) from bulk and cake solutions in a lab-scale AnMBR, and their fouling potential was further explored based on their filtration behavior and biofilm formation. Results show that with decreasing particle size, a significant shift in microbial communities was observed for the sub-visible particles in both bulk and cake solutions; (a) with notable decreases in filamentous microbes in the order SJA-15, GCA004, and Anaerolineales of phylum Chloroflexi, and, (b) with substantial increases in sulfate-reducing bacteria (i.e., the family Syntrophobacteraceae, genus DCE29 of family Thermodesulfovibrionaceae, Desulfovibrio, and Geobacter). More importantly, the filamentous microbes associated with micro-particles (5–10 μm) led to higher cake fouling resistances while free living cells in the form of colloidal particles (0.45–1 μm) induced severer pore blocking. Moreover, the micro-particles had an enhanced capacity to favor biofilm formation (OD595 = 1.0–2.5, categorized as highly positive), thus potentially aggravating biofouling. This work advances our knowledge on the effect of particle size on communities and underlying fouling behavior of microbes associated with fine particles in AnMBRs.

Holographic Characterization of Contaminants in CMP Slurries

Holographic Microscopy is used to characterize sub-visible particles in CMP nanoparticles slurries. Results of these studies detect and identify a wide range of different large particle contaminants in nanoparticle slurries. Holographic characterization has the unique ability to measure the composition as well as the size of these contaminants. We will present results demonstrating the ability to detect, count and characterize compact dense agglomerates, loosely packed low-density agglomerates, glass particles, polymeric particles and oil droplets in nanoparticles CMP slurries.

Separation, Characterization and Discriminant Analysis of Subvisible Particles in Biologics Formulations.

The presence of subvisible particles (SVPs) in parenteral formulations of biologics is a major challenge in the development of therapeutic protein formulations. Distinction between proteinaceous and non-proteinaceous SVPs is vital in monitoring formulation stability. The current compendial method based on light obscuration (LO) has limitations in the analysis of translucent/low refractive index particles. A number of attempts have been made to develop an unambiguous method to characterize SVPs, albeit with limited success. Herein, we describe a robust method that characterizes and distinguishes both potentially proteinaceous and non-proteinaceous SVPs in protein formulations using Microflow imaging (MFI) in conjunction with the MVAS software (MFI View Analysis Suite), developed by ProteinSimple. The method utilizes two Intensity parameters and a morphological filter that successfully distinguishes proteinaceous SVPs from non-proteinaceous SVPs and mixed aggregates. The MFI generated raw data of a protein sample is processed through Lumetics LINK software that applies an in-house developed filter to separate proteinaceous from the rest of the particulates.

Assessing Analytical and Functional Similarity of Proposed Amgen Biosimilar ABP 980 to Trastuzumab.

BackgroundABP 980 has been developed as a biosimilar to Herceptin® (trastuzumab). Comprehensive analytical characterization incorporating orthogonal analytical techniques was used to compare ABP 980 to trastuzumab reference products sourced from the United States (US) and the European Union (EU).MethodsPhysicochemical property comparisons included the following: primary structure related to amino acid sequence and post-translational modifications, including glycans; higher-order structure; product-related substances and impurities, including size and charge variants; subvisible and submicron particles, and protein content. In addition, functional similarity was assessed for Fab-mediated, Fc-mediated, and combined Fab- and Fc-mediated activities.ResultsABP 980 has the same amino acid sequence as and similar post-translational modification profiles to trastuzumab (US) and trastuzumab (EU). Importantly, ABP 980 was found to be highly similar to trastuzumab for all functional activities related to the mechanism(s) of action. Higher-order structure, product-related substances and impurities, particles and aggregates were also highly similar between ABP 980 and trastuzumab. Where minor differences were noted, they were evaluated and found unlikely to impact clinical performance. The totality of evidence, including the pharmacokinetic clinical similarity of ABP 980, further supports that ABP 980 is highly similar to trastuzumab.ConclusionBased on the comprehensive analytical similarity assessment, ABP 980 is analytically highly similar to the reference product, trastuzumab.

Evaluation of in vitro Assays to Assess the Modulation of Dendritic Cells Functions by Therapeutic Antibodies and Aggregates.

Therapeutic antibodies have the potential to induce immunogenicity leading to the development of anti-drug antibodies (ADA) that consequently may result in reduced serum drug concentrations, a loss of efficacy or potential hypersensitivity reactions. Among other factors, aggregated antibodies have been suggested to promote immunogenicity, thus enhancing ADA production. Dendritic cells (DC) are the most efficient antigen-presenting cell population and are crucial for the initiation of T cell responses and the subsequent generation of an adaptive immune response. This work focuses on the development of predictive in vitro assays that can monitor DC maturation, in order to determine whether drug products have direct DC stimulatory capabilities. To this end, four independent laboratories aligned a common protocol to differentiate human monocyte-derived DC (moDC) that were treated with either native or aggregated preparations of infliximab, natalizumab, adalimumab, or rituximab. These drug products were subjected to different forms of physical stress, heat and shear, resulting in aggregation and the formation of subvisible particles. Each partner developed and optimized assays to monitor diverse end-points of moDC maturation: measuring the upregulation of DC activation markers via flow cytometry, analyzing cytokine, and chemokine production via mRNA and protein quantification and identifying cell signaling pathways via quantification of protein phosphorylation. These study results indicated that infliximab, with the highest propensity to form aggregates when heat-stressed, induced a marked activation of moDC as measured by an increase in CD83 and CD86 surface expression, IL-1β, IL-6, IL-8, IL-12, TNFα, CCL3, and CCL4 transcript upregulation and release of respective proteins, and phosphorylation of the intracellular signaling proteins Syk, ERK1/2, and Akt. In contrast, natalizumab, which does not aggregate under these stress conditions, induced no DC activation in any assay system, whereas adalimumab or rituximab aggregates induced only slight parameter variation. Importantly, the data generated in the different assay systems by each partner site correlated and supported the use of these assays to monitor drug-intrinsic propensities to drive maturation of DC. This moDC assay is also a valuable tool as an in vitro model to assess the intracellular mechanisms that drive DC activation by aggregated therapeutic proteins.

Interfacial Stress in the Development of Biologics: Fundamental Understanding, Current Practice, and Future Perspective

Biologic products encounter various types of interfacial stress during development, manufacturing, and clinical administration. When proteins come in contact with vapor–liquid, solid–liquid, and liquid–liquid surfaces, these interfaces can significantly impact the protein drug product quality attributes, including formation of visible particles, subvisible particles, or soluble aggregates, or changes in target protein concentration due to adsorption of the molecule to various interfaces. Protein aggregation at interfaces is often accompanied by changes in conformation, as proteins modify their higher order structure in response to interfacial stresses such as hydrophobicity, charge, and mechanical stress. Formation of aggregates may elicit immunogenicity concerns; therefore, it is important to minimize opportunities for aggregation by performing a systematic evaluation of interfacial stress throughout the product development cycle and to develop appropriate mitigation strategies. The purpose of this white paper is to provide an understanding of protein interfacial stability, explore methods to understand interfacial behavior of proteins, then describe current industry approaches to address interfacial stability concerns. Specifically, we will discuss interfacial stresses to which proteins are exposed from drug substance manufacture through clinical administration, as well as the analytical techniques used to evaluate the resulting impact on the stability of the protein. A high-level mechanistic understanding of the relationship between interfacial stress and aggregation will be introduced, as well as some novel techniques for measuring and better understanding the interfacial behavior of proteins. Finally, some best practices in the evaluation and minimization of interfacial stress will be recommended.

Monitoring polysorbate hydrolysis in biopharmaceuticals using a QC-ready free fatty acid quantification method

Hydrolysis of the non-ionic surfactant polysorbate upon long-term storage poses significant challenges to development of biopharmaceutical liquid formulations. Low concentrations of intact surfactant may compromise its protective properties and thus affect protein stability. In addition, accumulation of polysorbate hydrolysis products is increasingly put into context with the formation of visible and subvisible particulates based on the low solubility of the main degradation products. Despite of this potential negative impact on product quality, quantification of the released free fatty acids is performed commonly in an indirect and consequently insensitive manner by determining the remaining PS content or by cumbersome methods, which are unsuitable for routine testing in quality control laboratories. For this purpose, this study describes the development and qualification of a label-free, reliable liquid-chromatography single quad mass detector (LC-QDa)-based method capable of resolving slight changes in the free fatty acid profile which can be readily integrated into quality control facilities. The practical utility of the herein described method is outlined by a case study on the real-time storage stability of a formulated monoclonal antibody.