Sub-millimeter Precision Research Articles

Time-resolved QA and brachytherapy applicator commissioning: Towards the clinical implementation

PurposeBrachytherapy has a busy workflow relying on manual steps to ensure accurate delivery of the treatment. Systematic treatment errors have been reported due to faulty equipment, inadequate quality assurance (QA) and applicator commissioning methods. This study describes the use of a novel method, the Iridium Imaging System for QA (IrIS – QA), to automate and improve the applicator commissioning for HDR 192Ir brachytherapy. Methods and MaterialsA 3D printed holder attached to an Imaging Panel (IP) has been developed to: (1) acquire a high-definition projection of the applicator using the gamma rays of the 192Ir source for imaging; (2) Track the source within the applicator verifying in a time-resolved manner the dwell positions and dwell times with a high resolution. Results obtained for two applicator models are described in this manuscript. ResultsIrIS-QA is capable of measuring the dwell times with an accuracy better than 0.1 s and interdwell distances with submillimetre precision. The applicators tested in the study showed good agreement between planned and delivered dwell times and positions, with mean and maximum dwell position deviations below 0.5 mm and 1.3 mm, respectively. Dwell time measurements showed agreement superior to 0.05 s except for the first dwell position for which up to 0.15 s differences were observed. ConclusionsIrIS-QA is a compact system that includes many features necessary to improve the accuracy and efficiency of applicator commissioning and daily QA. No commercial system exists with similar capabilities. IrIS-QA is intended to replace current clinical procedures using film dosimetry.

Two-channel 3D range geometry compression with primitive depth modification

Modern computing and imaging technologies have allowed for many recent advances to be made in the field of 3D range imaging: range data can now be acquired at speeds much faster than real-time, with sub-millimeter precision. However, these benefits come at the cost of an increased quantity of data being generated by 3D range imaging systems, potentially limiting the number of applications that can take advantage of this technology. One common approach to the compression of 3D range data is to encode it within the three color channels of a traditional 24-bit RGB image. This paper presents a novel method for the modification and compression of 3D range data such that the original depth information can be stored within, and recovered from, only two channels of a traditional 2D RGB image. Storage within a traditional image format allows for further compression to be realized via lossless or lossy image compression techniques. For example, when JPEG 80 is used to store the encoded output image, this method achieves an 18.2% reduction in file size when compared to a similar three-channel, image-base compression method, with only a corresponding 0.17% reduction in global reconstruction accuracy.

Simultaneous identification, modeling and registration refinement of poles using laser scanning point clouds

The method presented herein performs the tasks of identification, modeling, and registration refinement of poles using Light Detection And Ranging (LiDAR) point clouds. This method starts with a preliminary segmentation followed by eliminating outliers by integrating Fourier series and robust estimators. Poles’ cross sectional shapes are then identified by a customized template matching. Afterwards, points belonging to poles are extracted and the as-built model and registration-refined version of poles are generated. The algorithm was tested on five datasets including point clouds of three industrial sites, an urban environment, and a pole-like monument with very different volumes, resolutions, and configurations. The developed method works robustly despite the challenges that are often present in LiDAR data comprising outliers, non-uniform point sampling, gaps, and registration error. The obtained results indicate that 116 out of 117 poles in all five datasets were identified with no false positives at the object level. At point level, it reached greater than 98% average precision and 98% average accuracy in all datasets. Poles were modeled with a sub-millimeter precision in all datasets except for the third dataset in which poles were modeled with millimeter precision.

Sub-millimetre precision of drug delivery in the brain from ultrasound-triggered nanodroplets

Drug-loaded nanoscale cavitation agents, called nanodroplets, are an attractive solution to enhance and localize drug delivery, offering increased stability and prolonged half-life in circulation compared to microbubbles. However, the spatial precision with which drug can be released and delivered into brain tissue from such agents has not been directly mapped. Decafluorobutane lipid-shell droplets (206 +/− 6 nm) were loaded with a fluorescent blood-brain barrier (BBB)-penetrating dye (Nile Blue) and vaporized with ultrasound (1.66 MHz, 10 ms pulse length, 1 Hz pulse repetition frequency), generating transient echogenic microbubbles and delivering the encapsulated dye. The distribution and intensity of released fluorophore was mapped in a tissue-mimicking phantom, and in the brain of rats (Sprague Dawley, N = 4, n = 16). The release and distribution of dye was found to be pressure-dependent (0.2–3.5 MPa) and to occur only above the vaporization threshold of the nanodroplets (1.5 +/− 0.25 MPa in vitro, 2.4 +/− 0.05 MPa in vivo). Dye delivery was achieved with sub-millimetre spatial precision, covering an area of 0.4 to 1.5 mm in diameter, determined by the sonication pressure. The distribution and intensity of dye released at depth in the brain followed the axial pressure profile of the ultrasound beam. Nile Blue (354 Da, LogP 2.7) was compared to Nile Red (318 Da, LogP 3.8) and Quantum Dots (CdSe/ZnS, 5 nm diameter) to visualize the role of molecule size and lipophilicity in crossing the intact BBB following triggered release. Acoustic emissions were shown to predict the successful delivery of the BBB-penetrating dye and the extent of the distribution, demonstrating the theranostic capabilities of nanoscale droplets to precisely localize drug delivery in the brain.

Focused ultrasound for functional neurosurgery.

Brain lesioning is a fundamental technique in the functional neurosurgery world. It has been investigated for decades and presented promising results long before novel pharmacological agents were introduced to treat movement disorders, psychiatric disorders, pain, and epilepsy. Ablative procedures were replaced by effective drugs during the 1950s and by Deep Brain Stimulation (DBS) in the 1990s as a reversible neuromodulation technique. In the last decade, however, the popularity of brain lesioning has increased again with the introduction of magnetic resonance-guided focused ultrasound (MRgFUS). In this review, we will cover the current and emerging role of MRgFUS in functional neurosurgery. Literature review from PubMed and compilation. Investigated since 1930, MRgFUS is a technology enabling targeted energy delivery at the convergence of mechanical sound waves. Based on technological advancements in phased array ultrasound transducers, algorithms accounting for skull penetration by sound waves, and MR imaging for targeting and thermometry, MRgFUS is capable of brain lesioning with sub-millimeter precision and can be used in a variety of clinical indications. MRgFUS is a promising technology evolving as a dominant tool in different functional neurosurgery procedures in movement disorders, psychiatric disorders, epilepsy, among others.

Development of a storage phosphor imaging system for proton pencil beam spot profile determination.

Accurate two-dimensional (2D) profile measurements at submillimeter precision are necessary for proton beam commissioning and periodic quality assurance (QA) purposes and are currently performed at our institution with a commercial scintillation detector (Lynx PT) with limited means for independent checks. The purpose of this work was to create an independent dosimetry system consisting of an in-house optical scanner and a BaFBrI:Eu2+ storage phosphor dosimeter by: (a) determining the optimal settings for the optical scanner, (b) measuring 2D proton spot profiles with the storage phosphors, and (c) comparing them to similar measurements using a commercial scintillation detector. An in-house 2D laboratory optical scanner was constructed and spatially calibrated for accurate 2D photostimulated luminescence (PSL) dosimetry. Square 5×5cm2 BaFBrI:Eu2+ dosimeter samples were uniformly irradiated with line scans performed to determine the physical and electronic scanner settings resulting in the highest signal-to-noise ratios (SNR) at a sub-millimeter spatial resolution. The resultant spatial resolution of the scanner was then quantitatively assessed by measuring (a) line pairs on a standard X-ray lead bar phantom and (b) modulation transfer functions. Following this, 2D proton spot profiles from a Mevion S250i Hyperscan proton unit were obtained at 1, 10, 20, 30, 40, and 50 monitor unit (MU) settings at maximum energy (E0 =227.1MeV) and compared to baseline profiles from a commercial scintillation detector, where 1MU is calibrated to deliver 1Gy absolute proton dose-to-water under reference conditions, that is, 41×41 proton spots uniformly spaced by 0.25cm within a 10×10cm2 square field size at maximum energy (227.1MeV) in water at depth of 5cm at isocenter. The dosimetric system's sensitivities to (a) ±1mm positional shifts and (b) ±0.3mm beam lateral spread changes were quantitatively evaluated through a Gaussian fitting of the crossline and inline plots of the respective artificially shifted beam profiles. The physical scanner settings of (a) Δτ=27ms time interval between data samples, (b) vx =1.235cm/s scanning speed, (c) 1% laser transmission (0.02mW power) and (d) (Δx, Δy)=(0.33, 0.50mm) pixel sizes with electronic settings of (a) 300 microseconds time constant, (b) normal dynamic reserve, (c) 24dB/oct low pass filter slope, and (d) 160Hz chopping frequency resulted in the highest SNR while maintaining sub-millimeter spatial resolution. The BaFBr0.85 I0.15 :Eu2+ storage phosphor dosimeters were linear from 1 to 50MU and their profiles did not saturate up to 150MU. The scanner was able to detect lateral displacements of ±1mm in both the crossline and inline directions and ±0.3mm beam spread changes that were artificially introduced by varying the incident proton energy. Specific to our proton unit, proton energy changes of ±1MeV can also be detected indirectly via beam spread measurements. Our combined dosimetric system including an in-house laboratory optical scanner and reusable BaFBr0.85 I0.15 :Eu2+ storage phosphors demonstrated a sufficient spatial resolution and dosimetric accuracy to support its use as an independent proton spot measurement dosimeter system. Its wide dynamic range allows for other versatile applications such as proton halo measurements.

PD-0942 Intrafraction error analysis of homemade mouth-bite masks in linac-based SRS for brain metastasis

Purpose or Objective To assess the intrafraction accuracy of a frameless stereotactic linac-based radiosurgery (SRS) for brain metastases (BM) using a homemade mouth-bite thermoplastic mask in combination with cone-beam computed tomography (CBCT) and six-degrees of freedom (6-DOF) couchtop. Materials and Methods Covid-19 restrictions resulted in significant delays in the supply of the dedicated devices for BM SRS. A frameless approach using a homemade mouth-bite thermoplastic mask was implemented to offer BM SRS in a period of limited mobility (figure 1). All patients were immobilized and treated at the same institution with 6 MV FFF VMAT radiosurgery, with a 2 mm isotropic expansion from the GTV to the PTV. Before treatment delivery, patients underwent a low-dose CBCT to check position accuracy. Through image co-registration, translational (x, y, z) and rotational errors (roll, pitch, and yaw) were determined. The 6-DOF couchtop was used to automatically relocate the patient with sub-millimetric precision. Immediately after irradiation, patients underwent a second CBCT to verify any translational or rotational errors occurring during therapy (intrafraction motion). $Φg Results From February 2020 to January 2021 sixteen patients (29 lesions) received BM SRS (14-21 Gy). The whole procedure, from the first CBCT scan to the end of irradiation and subsequent CBCT, required a median time of 9 minutes [6-13]. Mean translational error was 0.0 ± 0.3 mm [-0.7;0.9] in lateral direction, and -0.1 ± 0.5 mm [-1.4;1.0] in longitudinal direction. A 2.2 mm maximum shift was recorded on the vertical axis, nevertheless the mean translation error was 0.1 ± 0.6 mm. Roll, pitch and yaw registered a mean value of -0.1 ± 0.3° [-0.8;0.2], 0.0 ± 0.2° [-0.8;0.2], and -0.1 ± 0.3° [-0.8;0.4], respectively. The results are summarized in figure 2. Conclusion This study demonstrated that homemade mouth-bite thermoplastic masks combined with CBCT, 6-DOF couchtop, and fast FFF treatment delivery allow minimal intra-fraction uncertainties in BM SRS, confirming the accuracy of PTV margin definition. The results are comparable to the declared specifics of SRS dedicated commercial frameless mask, while improving patient's comfort compared to the invasive fixed frame. However, the moulding procedure requires improved RTT skills and expertise. Our findings show that SRS can be safely delivered in radiotherapy units without dedicated expensive installations, such as CyberKnife and Gamma Knife, thus reducing patient mobility according to Covid-19 restrictions.

Shape accuracy of fiber optic sensing for medical devices characterized in bench experiments.

PurposeFiber Optic RealShape (FORS) is a new technology that visualizes the full three‐dimensional shape of medical devices, such as catheters and guidewires, using an optical fiber embedded in the device. This three‐dimensional shape provides guidance to clinicians during minimally invasive procedures, and enables intuitive navigation. The objective of this paper is to assess the accuracy of the FORS technology, as implemented in the current state‐of‐the‐art Philips FORS system. The FORS system provides the shape of the entire device, including tip location and orientation. We consider all three aspects.MethodsIn bench experiments, we determined the accuracy of the location and orientation of the tip by displacing and rotating the fiber end, while allowing the rest of the fiber to change shape freely. To test the accuracy of the full shape, we have placed the fiber in a groove, which was accurately machined in a thick, stiff metal “path plate.” We then compared the reconstructed shape with the known shape of the groove.ResultsThe tip location is found with submillimeter accuracy, and the orientation is sensed with milliradian accuracy. The shape of a fiber in the path plate faithfully follows the known shape of the groove, with typical deviation less than 0.5 mm in the plane of the plate. Out of plane accuracy, perhaps slightly less relevant clinically, is more challenging, due to the influence of twist; yet even out of the plane, the deviation is only submillimeter.ConclusionThe technology achieves submillimeter precision and provides full three‐dimensional shape, surpassing the reported precision of other navigation and tracking technologies, and therefore may potentially alleviate the need for fluoroscopy.

The dose magnifying glass quality assurance system for daily proton therapy range verification

Proton therapy has a distinct dosimetric advantage over conventional photon therapy due to its Bragg peak profile. This allows greater accuracy in dose delivery and dose conformation to the target, however it requires greater precision in setup, delivery and for quality assurance (QA) procedures. The AAPM TG 224 report recommends daily range and spot position checks with tolerance on the order of a millimetre. Daily QA systems must therefore be efficient for daily use and be capable of sub-millimetre precision however few suitable commercial systems are available. In this work, a compact, real-time daily QA system is optimised and characterised for proton range verification using an ad-hoc Geant4 simulation. The system is comprised of a monolithic silicon diode array detector embedded in a perspex phantom. The detector is orientated at an angular offset to the incident proton beam to allow range in perspex to be determined for flat proton fields. The accuracy of the system for proton range in perspex measurements was experimentally evaluated over the full range of clinical proton energies. The mean R 100, R 90 and R 80 ranges measured with the system were accurate within ±0.6 mm of simulated ranges in a perspex phantom for all energies assessed. This system allows real-time read-out of individual detector channels also making it appropriate for temporal beam delivery diagnostics and for spot position monitoring along one axis. The system presented provides a suitable, economical and efficient alternative for daily QA in proton therapy.

Short-baseline interferometry local-tie experiments at the Onsala Space Observatory

We present results from observation, correlation and analysis of interferometric measurements between the three geodetic very long baseline interferometry (VLBI) stations at the Onsala Space Observatory. In total, 25 sessions were observed in 2019 and 2020, most of them 24 h long, all using X band only. These involved the legacy VLBI station ONSALA60 and the Onsala twin telescopes, ONSA13NE and ONSA13SW, two broadband stations for the next-generation geodetic VLBI global observing system (VGOS). We used two analysis packages: nu Solve to pre-process the data and solve ambiguities, and ASCOT to solve for station positions, including modelling gravitational deformation of the radio telescopes and other significant effects. We obtained weighted root mean square post-fit residuals for each session on the order of 10–15 ps using group-delays and 2–5 ps using phase-delays. The best performance was achieved on the (rather short) baseline between the VGOS stations. As the main result of this work, we determined the coordinates of the Onsala twin telescopes in VTRF2020b with sub-millimetre precision. This new set of coordinates should be used from now on for scheduling, correlation, as a priori for data analyses, and for comparison with classical local-tie techniques. Finally, we find that positions estimated from phase-delays are offset sim +3 mm in the up-component with respect to group-delays. Additional modelling of (elevation dependent) effects may contribute to the future understanding of this offset.

Development of a Submillimetric GNSS-Based Distance Meter for Length Metrology.

Absolute distance determination in the open air with an uncertainty of a few tenths of a millimetre is increasingly required in many applications that involve high precision geodetic metrology. No matter the technique used to measure, the resulting distances must be proven consistent with the unit of length (SI-metre) as realized in the outdoor facilities traditionally used in length metrology, which are also known as calibration baselines of reference. The current calibration baselines of reference have distances in the range of 10 to 1000 m, but at present there is no solution on the market to provide distances with submillimetric precision in that range. Consequently, new techniques such as multi-wave interferometry, two-wave laser telemeters or laser trackers are being developed. A possible alternative to those sophisticated and expensive techniques is the use of widely used Global Navigation Satellite Systems (GNSS) in order to provide a GNSS-Based Distance Meter (GBDM). The use of a GBDM as a potential technique for length metrology has been thoroughly analysed in several European research projects by using the state-of-the-art geodetic software, such as Bernese 5.2, but no definite conclusions have been drawn and some metrological questions are considered still open. In this paper, we describe a dedicated approach to build up a submillimetric GBDM able to be applied in the current calibration baselines of reference, as well as possible methods to cope with the multipath error of the GNSS signals which is the major limitation for the practical uptaking of the technique in metrology. The accuracy of the proposed approach has been tested following the length metrology standards in four experiments carried out in the Universitat Politècnica de València (UPV). The results demonstrate that the proposed GBDM can provide an accuracy of a few tenths of a millimetre in the current calibration baselines of reference.

Infrared neural stimulation with 7T fMRI: A rapid in vivo method for mapping cortical connections of primate amygdala

We have previously shown that INS-fMRI is a rapid method for mapping mesoscale brain networks in the macaque monkey brain. Focal stimulation of single cortical sites led to the activation of connected cortical locations, resulting in a global connectivity map. Here, we have extended this method for mapping brainwide networks following stimulation of single subcortical sites. As a testbed, we focused on the basal nucleus of the amygdala in the macaque monkey. We describe methods to target basal nucleus locations with submillimeter precision, pulse train stimulation methods, and statistical tests for assessing non-random nature of activations. Using these methods, we report that stimulation of precisely targeted loci in the basal nucleus produced sparse and specific activations in the brain. Activations were observed in the insular and sensory association cortices as well as activations in the cingulate cortex, consistent with known anatomical connections. What is new here is that the activations were focal and, in some cases, exhibited shifting topography with millimeter shifts in stimulation site. The precision of the method enables networks mapped from different nearby sites in the basal nucleus to be distinguished. While further investigation is needed to improve the sensitivity of this method, our analyses do support the reproducibility and non-random nature of some of the activations. We suggest that INS-fMRI is a promising method for mapping large-scale cortical and subcortical networks at high spatial resolution.

Two-Channel 3D Range Geometry Compression with Virtual Plane Encoding

Modern computing and imaging technologies have allowed for many recent advances to be made in the field of 3D range imaging: range data can now be acquired at speeds much faster than real-time, with sub-millimeter precision. However, these benefits come at the cost of an increased quantity of data being generated by 3D range imaging systems, potentially limiting the number of applications that can take advantage of this technology. One common approach to the compression of 3D range data is to encode it within the three color channels of a traditional 24-bit RGB image. This paper presents a novel method for the modification and compression of 3D range data such that the original depth information can be stored within, and recovered from, only two channels of a traditional 2D RGB image. Storage within a traditional image format allows for further compression to be realized via lossless or lossy image compression techniques. For example, when JPEG 80 was used to store the encoded output image, this method was able to achieve an 18.2% reduction in file size when compared to a similar three-channel, image-base compression method, with only a corresponding 0.17% reduction in global reconstruction accuracy.

Vegetation effects on coastal foredune initiation: Wind tunnel experiments and field validation for three dune-building plants

As the land-sea interface, foredunes buffer upland habitats with plants acting as ecosystem engineers shaping topography, and thereby affecting storm response and recovery. However, many ecogeomorphic feedbacks in coastal foredune formation and recovery remain uncertain in this dynamic environment. We carried out a series of wind tunnel experiments testing how the morphology, density, and configuration of three foredune pioneer dune building plant species influence the most basic stage of dune initiation — nebkha formation around individual plants. We established monocultures of native Ammophila breviligulata and Panicum amarum and invasive Carex kobomugi in 1 m × 1 m planter boxes of sand to simulate approximate natural and managed densities and planting configurations on the US Mid-Atlantic coast. We subjected each box to constant 8.25 m/s wind for 30 min in a moveable-bed unilateral-flow wind tunnel with an unvegetated upwind sand bed. We quantified resulting topography with sub-millimeter precision and related it to plant morphology, density, and configuration. Plant morphology, density, and configuration all influenced the resulting topography. Larger plants produced larger nebkha with greater relief, height, and sand volume. However, nebkha area, height, and planform shape varied among species, and taller plants did not necessarily produce taller nebkha. The erect grasses, Ammophila and Panicum, produced more elongated, high-relief nebkha compared to the low-lying Carex, which produced lower and more symmetrical equant nebkha. A staggered planting configuration produced greater net sediment accumulation than non-staggered. We validated these results against high-resolution field topographies of foredune nebkha and found strong agreement between the datasets. Our results provide species-specific parameters useful in designing foredune plantings and beach management and can be used to parameterize vegetation in models of foredune evolution associated with different plant species. By first understanding the underlying ecogeomorphic feedbacks involved in nebkha formation, we can more effectively scale up to forecast coastal foredune evolution and recovery.

Technical Note: Synthetic treatment beam imaging for motion monitoring during spine SBRT treatments - a phantom study.

One of the biggest challenges in applying megavoltage (MV) treatment beam imaging for monitoring spine motion in stereotactic body radiotherapy (SBRT) is the small beam apertures in the images due to strong beam modulations in IMRT planning. The purpose of this study is to investigate the feasibility of a markerless motion tracking method in spine SBRT delivery using a novel enhanced synthetic treatment beam (ESTB) imaging technique. Three clinical spine SBRT plans using 6XFFF beams and sliding window IMRT technique were transferred to a thorax phantom and delivered by a TrueBeam machine. Before delivery, the phantom was aligned to the plan isocenter using CBCT setup and verified with a second CBCT, and then, 2mm shifts were introduced in both the craniocaudal (CC) and the left-right (LR) directions with the couch. During beam delivery, MV images were continuously taken with an electronic portal imaging device (EPID) and automatically grabbed by Varian iTools Capture software with a frame rate of 11.6Hz. After preprocessing for scatter correction and beam intensity compensation, every 50 frames of MV images were combined to generate a series of ESTB images for each beam. The ESTB images were then registered to the projections of the verification CBCT at the matched beam angles to detect the 2mm shifts. Compared to snapshot MV images, the ESTB images had significantly enlarged fields of view (FOVs) and improved image quality. Based on two-dimensional (2D) rigid registration, the ESTB image to CBCT projection matching showed submillimeter accuracy in detecting motion. Specifically, the root mean square errors in detecting the LR/CC shifts were 0.35/0.28, 0.32/0.35, 0.63/0.44, 0.55/0.51, and 0.69/0.42mm at gantry angles 180, 160, 140, 120, and 100, respectively. Our results in the phantom study suggest that ESTB images from a sliding window IMRT plan can be used to detect spine motion, with submillimeter precision in the 2D plane perpendicular to the beam.

Cardiac CT angiography: normal and pathological anatomical features-a narrative review.

The normal and pathological anatomy of the heart and coronary arteries are nowadays widely developed topics and constitute a fundamental part of the cultural background of the radiologist. The introduction of cardiac ECG-gated synchronized CT scanners with an ever-increasing number of detectors and with increasingly high structural characteristics (increase in temporal resolution, increase in contrast resolution with dual-source, dual energy scanners) allows the virtual measurement of anatomical in vivo structures complying with heart rate with submillimetric precision permitting to clearly depict the normal anatomy and follow the pathologic temporal evolution. Accordingly to these considerations, cardiac computed tomography angiography (CCTA) asserts itself as a gold standard method for the anatomical evaluation of the heart and permits to evaluate, verify, measure and characterize structural pathological alterations of both congenital and acquired degenerative diseases. Accordingly, CCTA is increasingly used as a prognostic model capable of modifying the outcome of diseased patients in planning interventions and in the post-surgical/interventional follow-up. The profound knowledge of cardiac anatomy and function through highly detailed CCTA analysis is required to perform an efficient and optimal use in real-world clinical practice.

Independent representations of self-motion and object location in barrel cortex output.

During active tactile exploration, the dynamic patterns of touch are transduced to electrical signals and transformed by the brain into a mental representation of the object under investigation. This transformation from sensation to perception is thought to be a major function of the mammalian cortex. In primary somatosensory cortex (S1) of mice, layer 5 (L5) pyramidal neurons are major outputs to downstream areas that influence perception, decision-making, and motor control. We investigated self-motion and touch representations in L5 of S1 with juxtacellular loose-seal patch recordings of optogenetically identified excitatory neurons. We found that during rhythmic whisker movement, 54 of 115 active neurons (47%) represented self-motion. This population was significantly more modulated by whisker angle than by phase. Upon active touch, a distinct pattern of activity was evoked across L5, which represented the whisker angle at the time of touch. Object location was decodable with submillimeter precision from the touch-evoked spike counts of a randomly sampled handful of these neurons. These representations of whisker angle during self-motion and touch were independent, both in the selection of which neurons were active and in the angle-tuning preference of coactive neurons. Thus, the output of S1 transiently shifts from a representation of self-motion to an independent representation of explored object location during active touch.

Observation of an Unusual Long Component in the Electroluminescence of a Two-Phase Argon Detector

Proportional electroluminescence in noble gases is used in two-phase detectors for dark-matter searches for detecting ionization signals in a liquid phase (S2 signals). Time features of electroluminescence signals in a two-phase argon detector were studied systematically both over a broad range of reduced electric fields—from 3 to 9 Td (Townsend)—and for various methods of optical readout in different spectral ranges—by means of cryogenic photomultiplier tubes (PMTs) and silicon photomultipliers (SiPMs), with a wavelength shifter and without it, in vacuum ultraviolet and visible ranges. Both a fast and a slow component of signals were observed. An observation of an unusual long component of the S2 signal is described in the present article. This component has a time constant of about 40 $$\mu$$ s, which grows with increasing electric field, and can not be explained in terms of known scintillation mechanisms. Also, it is shown here that the fast component can be used to measure the thickness of the electroluminescence gap to a submillimeter precision. The results obtained in these experiments may find practical applications in the DarkSide experiment devoted to searches for dark matter.

A fiber optoacoustic emitter with controlled ultrasound frequency for cell membrane sonoporation at submillimeter spatial resolution

Focused ultrasound has attracted great attention in minimally invasive therapeutic and mechanism studies. Frequency below 1 MHz is identified preferable for high-efficiency bio-modulation. However, the poor spatial confinement of several millimeters and large device diameter of ∼25 mm of typical sub-MHz ultrasound technology suffered from the diffraction limit, severely hindering its further applications. To address it, a fiber-based optoacoustic emitter (FOE) is developed, serving as a miniaturized ultrasound point source, with sub-millimeter confinement, composed of an optical diffusion layer and an expansion layer on an optical fiber. By modifying acoustic damping and light absorption performance, controllable frequencies in the range of 0.083 MHz–5.500 MHz are achieved and further induce cell membrane sonoporation with frequency dependent efficiency. By solving the problem of compromise between sub-MHz frequency and sub-millimeter precision via breaking the diffraction limit, the FOE shows a great potential in region-specific drug delivery, gene transfection and neurostimulation.

Scatter imaging during lung stereotactic body radiation therapy characterized with phantom studies

By collecting photons scattered out of the therapy beam, scatter imaging creates images of the treated volume. Two phantoms were used to assess the possible application of scatter imaging for markerless tracking of lung tumors during stereotactic body radiation therapy (SBRT) treatment. A scatter-imaging camera was assembled with a CsI flat-panel detector and a 5 mm diameter pinhole collimator. Scatter images were collected during the irradiation of phantoms with megavoltage photons. To assess scatter image quality, spherical phantom lung tumors of 2.1–2.8 cm diameters were placed inside a static, anthropomorphic phantom. To show the efficacy of the technique with a moving target (3 cm diameter), the position of a simulated tumor was tracked in scatter images during sinusoidal motion (15 mm amplitude, 0.25 Hz frequency) in a dynamic lung phantom in open-field, dynamic conformal arc (DCA), and volumetric modulated arc therapy (VMAT) deliveries. Anatomical features are identifiable on static phantom scatter images collected with 10 MU of delivered dose (2.1 cm diameter lung tumor contrast-to-noise ratio of 4.4). The contrast-to-noise ratio increases with tumor size and delivered dose. During dynamic motion, the position of the 3.0 cm diameter lung tumor was identified with a root-mean-square error of 0.8, 1.2, and 2.9 mm for open field (0.3 s frame integration), DCA (0.5 s), and VMAT (0.5 s), respectively. Based on phantom studies, scatter imaging is a potential technique for markerless lung tumor tracking during SBRT without additional imaging dose. Quality scatter images may be collected at low, clinically relevant doses (10 MU). Scatter images are capable of sub-millimeter tracking precision, but modulation decreases accuracy.