Fiber Strength Research Articles

Vine copulas for accelerated prediction of composite strength variability

Composite materials are essential for many advanced engineering applications, but numerical quantification of strength variability can be computationally expensive. This paper proposes a novel methodology that drastically reduces the number of finite element simulations required to characterise composite material strength variability using the concept of vine copulas. This concept provides a flexible tool for the representation of high-dimensional dependencies. The methodology considers spatial scatter of three material variabilities: fibre volume fraction, fibre misalignment and fibre strength. First, the cross-correlation between stress, fibre volume fraction and fibre misalignment is fitted by a vine copula using results from a limited number of finite element simulations. Next, the vine copula is used to predict new conditional stress realisations when given realisations for the fibre volume fraction and fibre misalignment. This effectively replaces the finite element simulations with a vine copula that is much faster to evaluate. The methodology is verified by predicting the tensile failure load of a unidirectional composite coupon. Predictions are very similar to an exclusively finite element-based approach, while reducing the number of finite element simulations by a factor of 200.

High-strength alginate fibers wet-spun from pre-crosslinked sodium alginate solutions

Facing the severe problem of microplastic pollution, there is an urgent need to develop biodegradable fibers to replace the petrochemical fibers. Sodium alginate, a biomass polysaccharide, has gained widespread attentions recently for the fiber manufacture. However, the limited mechanical strength of alginate fibers restricts their usages as load-bearing fabrics and reinforcement fibers. Here, we develop a novel strategy to prepare alginate multifilaments using pre-crosslinked sodium alginate solutions. The increase in the pre-crosslinking ratio effectively hinders the disentanglement of sodium alginate chains at high stretches, causing an increase in the shear viscosity of the solution ascertained from the capillarity-driven thinning process from 4.5 Pa·s to 9.9 Pa·s and facilitating the high alignment and orientation of sodium alginate chains. The resultant fibers possess a breaking strength of 474 MPa, elongation at break of 16 %, Young's modulus of 14.4 GPa, and toughness of 51.8 MJ/m3, exceeding most biomass fibers without reinforcement additives. The high orientation degree of 0.865 and high spinnability of alginate multifilaments enable their applications in multi-channel encryption fabrics that exhibit distinct information under various optical conditions. This rheological regulation of spinning solutions provides a facile yet effective strategy to enhance the mechanical performance and broaden application scenarios of alginate fibers.

Nano silica grafted on modified polyacrylonitrile fiber improves the interfacial strength of fiber‐reinforced concrete

AbstractCement is known to be brittle and usually reinforced with fibers. However, there is a lack of effective chemical bonding between organic fibers and inorganic cement, resulting in a weaker interfacial bonding strength. In this paper, amino hyperbranched polymer (HBP) was used to modify the surface of polyacrylonitrile (PAN) fibers, and then silica nanoparticles (SiO2 NPs) were grafted on the surface of modified PAN fibers to realize the inorganic treatment of organic fibers. The modified PAN fibers applied to cement concrete can significantly enhance the interfacial strength between the fibers and cement. The morphology and chemical composition of the modified PAN fibers were characterized by scanning electron microscope, atomic force microscope, electron energy dispersive spectroscopy, and Fourier transform infrared spectroscopy, and the influence of grafting conditions on grafting effect was analyzed. The results show that SiO2 NPs were evenly distributed on the surface of PAN fiber. When SiO2 NPs concentration was 4%, grafting temperature was 50°C, and grafting time was 4 h, the grafting degree of SiO2 NPs grafted PAN fiber can reach to 1.4%. After coating with SiO2 NPs, the pullout bonding strength of the PAN fiber was increased from 5.5 to 6.5 cN.

Ultra‐high bonding strength of carbon fiber–doped polyamide–aluminum alloy composite structure achieved by changing crystallinity

AbstractLightweight and high‐strength polymer–metal hybrid structures are favored for reducing material and energy consumption. In this study, carbon fiber‐reinforced polyamide 6 (CFPA) composite materials were prepared through melt blending, and 30 wt% CFPA exhibited the highest shear strength and lowest shrinkage rate among other carbon fiber contents. With pretreatments of anodizing and etching treatment, injection molded direct joining was employed to create polyamide 6 (PA)/CFPA–Aluminum alloy (Al) composites. The impacts of the injection temperature and speed on the bonding strength of the PA/CFPA–Al composite materials were investigated. The characterization results confirmed that carbon fiber doping reduces the coefficient of linear thermal expansion (CLTE) and enhances crystallization ability of PA. The higher injection temperatures and lower injection speed significantly increase the crystallinity of PA and the infiltration of the molten polymer into the nanoporous anodic aluminum oxide films. When the injection temperature was 270°C and the speed was 6 mm/s, the bonding strength of the PA–Al hybrid structure reached a maximum of 36.6 MPa. When the injection temperature was 300°C, the bonding strength of the CFPA–Al hybrid structure reached a maximum of 40.8 MPa. Adhesive parts with high shear bonding strength are critical to satisfying engineering requirements and have significant potential, particularly in polymer–metal composite structures. The polymer‐metal hybrid structure can meet the high interfacial bonding strength required in most engineering applications.Highlights Injection temperature and speed in IMDJ affect PA crystallinity. Carbon fiber doping reduces the CLTE of PA and increases the shear strength. High temperatures and low injection speeds are beneficial to adhesives. The bonding strength of PA–Al reached a maximum of 36.6 MPa. The bonding strength of CFPA–Al reached a maximum of 40.8 MPa.

Experimental study on debonding and buckling of externally bonded carbon fiber reinforced polymer sheets in compression

Although the compressive strength of Fiber Reinforced Polymer (FRP) sheets is neglected in the design of FRP-retrofitted Reinforced Concrete (RC) elements, they may be subjected to compressive stress in some load combinations. In the present study, an experimental study is conducted to investigate the behavior of externally bonded Carbon Fiber Reinforced Polymer (CFRP) sheets in compression. The experimental program is carried out in two phases. First, the behavior of CFRP strips bonded on concrete cylinders and subjected to pure compressive load is assessed. At this stage, the influence of concrete compressive strength, the dimensions of CFRP strips (thickness, width, and free length), and the type of adhesive used for bonding CFRP strips on the concrete surface, on the behavior of CFRP strips in compression are investigated. According to the test results, the FRP strips bonded with weak resin exhibit debonding failure and simultaneously buckle at a relatively low compressive strain, while CFRP strips bonded with stronger adhesive do not exhibit debonding failure in compression until concrete crushing. The behavior of CFRP strips bonded on reinforced concrete (RC) beams subjected to compressive stress due to bending moment is investigated in the second phase of this study. For this purpose, nine RC beams with the same dimensions and reinforcement detailing are fabricated and retrofitted using CFRP strips with different configurations. Four-point bending test is conducted at this stage of the experimental program. The results of the bending tests show that debonding failure and buckling of CFRP strips are observed in specimens with relatively thick CFRP sheets (3 and 4-layer) and larger free lengths.

Towards sustainable composites: Evaluation of mechanical properties, erosion behavior and applications of natural fiber-epoxy composites

Sustainable production and consumption, carried to materials and engineering applications, translates to a need for recyclable, reusable, and/or biodegradable materials. With its lower cost, lighter weight, and less carbon footprint compared to traditional glass and carbon fiber composites, natural fiber-reinforced composites are drawing more attention from the scientific community and the industrial sector. The natural fiber’s high variability and relatively inferior mechanical properties necessitate comprehensive characterization for accurate evaluation of their properties and fitness for different applications. In this research, various locally grown natural fibers (Flax, Jute, and Luffa) were sourced, characterized, and used to synthesize natural fiber-reinforced epoxy composites. The tensile, flexural, impact properties, and erosion resistance of the composites was evaluated. Compared to the other natural fiber composites, the Jute-Epoxy composite achieved the highest tensile strength and tensile modulus with 31 MPa and 4.8 GPa respectively; Jute-Epoxy also achieved the highest flexural strength and flexural modulus, with and 60 MPa and 2.4 GPa respectively. This superior mechanical performance is due to the relatively high strength of the Jute fiber and its high adhesion to the matrix, which is supported by fractographic evidence. Luffa-Epoxy composites in general had the lowest properties of all the tested materials. The erosion test results showed that the Jute-Epoxy composites had the highest erosion resistance of all the tested materials; with 30% more erosion resistance compared to glass-fiber epoxy composites. Based on the experimental results of the investigation and similar previous research, the current and potential applications of natural fiber composites were discussed.

Enhancement of tensile strength and fracture toughness characteristics of banana fibre reinforced epoxy composites with nano MgO fillers

Natural fibre reinforced polymer composites have drawn the attention of researchers in the creation of novel materials suitable for industrial applications. These polymer composites have favourable mechanical characteristics. Epoxy polymer's versatility and diversity make it suitable for a wide range of industrial applications. The mould casting technique approach was utilised in this work to develop polymer composites using alkali-treated banana fibres and filled with MgO nanoparticle. The study was conducted on the characteristics of Nano MgO, as well as its mechanical qualities such as fracture toughness and surface morphology. The incorporation of Nano MgO enhanced the fracture toughness of the polymer composites with the addition of 1 % MgO. The scanning electron microscopy analysis of the surface morphology revealed the presence of brittle fracture in the specimen.

Experimental characterization of Grewia Ferruginea fiber reinforced polyester matrix composite materials

Researchers have recently altered their focus and have become more interested in natural fiber-reinforced polymer composites because they are more ecologically friendly and environmentally conscious than synthetic fiber-reinforced polymer composites. Among the best sources of natural fiber, Grewia ferruginea, sometimes known locally as Lenquata, is a source of natural fiber from other plant fibers. The goal of this study was to create polyester matrix composites reinforced with short Grewia ferruginea plant fibers measuring 10, 20, and 30 mm. The fibers were extracted using the traditional water-retting method and chemically treated with 5% NaOH. The findings indicated that the average tensile strength of a single fiber from Grewia ferruginea plants is 214 MPa, with a density of 1.11 g/cm3. Furthermore, the composite, which was created with a fiber length of 10 mm, fiber weight ratio of 25 %, and polyester matrix composite of 75 %, exhibited superior performance since it is stronger than any combination that was used to create the composite in this investigation, with 18.3 MPa tensile and 35.2 MPa flexural strength.

GENETIC INSIGHTS AND BREEDING IMPLICATIONS: ENHANCING COTTON YIELD AND QUALITY THROUGH BIPARENTAL SELECTION

This study was performed in Egypt's Sakha Agriculture Research Station during the seasons 2015–2018 to study the efficiency of biparental progenies derived from inter-population random mating in F2 generation in a cotton cross. Intercrossing is allowed in cotton breeding populations. Although the best lines may include harmful alleles, thus early segregating generation recombination and hybridization are required. The F2 generation of the cotton cross (Giza70 TNB1), which obtained from Agriculture Research Center, Egypt, consisted of five male and eight female plants, was used to test biparental progeny from random interpopulation mating. About 28 and 24 families in BIPS1 and BIPS2 had their original parents were examined. All genotypes were assessed for agricultural and fiber qualities. The mean of families (BIPs2) was higher than BIPs1 for all measured metrics except lint yield, percentage, and uniformity ratio. BIPS2 families had more genotypic coefficients of variation (GCV) for features than BIPS1. Intercrossing affected correlation coefficients of BIPS1 and BIPS2 genotypes. Seed cotton yield and lint index genotypic correlations became considerable. Seed cotton yield estimated by seed index and first fruiting node location were altered from negative to positive. Among them, No.5, No.7, No.8, No.18, and No.19 had large yields and early ripening, as shown by their components. The top five families chosen for fiber length had gain values of 3.373% to 8.961% and 5.919 to 7.781% for fiber strength. The No.18 family exhibited good seed cotton production and fiber length. Intermating and self-pollination (BIPS2) may utilize non-additive gene effects and accumulate trait-influencing alleles. Continuing to select and evaluate families based on their large-scale reproductive performance will enhance the likelihood of producing genotypes with desired features. In conclusion, this study underscores the utility of continued selection based on discerned genetic parameters, genotypic correlations, and observed gains in facilitating the ongoing improvement of cotton breeding programs. By providing valuable insights into the intricacies of genetic variability and trait associations, this research holds implications not only for the advancement of cotton breeding practices but also for the broader agricultural landscape on both national and global scales. Keywords: Biparental, selection efficiency, correlated response, hybridization, self-pollination

Equol-based epoxy resin as an ideal substitute for the diglycidyl ether of bisphenol A (DGEBA)

The development of high-performance bio-based epoxies with excellent mechanical properties, heat resistance and flame retardant properties is essential to mitigating the resource and environmental burdens caused by the widespread utilization of petroleum-based epoxies. This work focuses on the synthesis of a bifunctional epoxy resin (EEU) with the rigid tetrahydrobenzopyran ring derived from equol. The structure of the EEU epoxy resin was characterized, and using 4,4′ diamino diphenyl sulfone as the curing agent, the rheological properties, curing behavior and comprehensive properties of cured resin were studied. The results demonstrate that EEU-DDS presents the same curing behavior as DGEBA-DDS. The mechanical properties heat resistance and flame retardant properties of EEU-DDS are superior to DGEBA-DDS. The tensile strength, tensile modulus and glass transition temperature reached to 94.0 MPa, 3.62 GPa and 221 °C, respectively, higher than those of DGEBA-DDS (83.2 MPa, 2.81 GPa and 203 °C). EEU-DDS reached the V-1 rating in UL-94 tests with a high limiting oxygen index (LOI) (28 %), and the peak heat release rate and smoke release rate of 631 kW/m2 and 0.155 m2/s were significantly lower than that of DGEBA-DDS. The flame retardant mechanism was proven to be gas-coacervated phase synergistic flame retardant. In addition, the interlamellar shear strength (ILSS), bending strength, and impact strength of carbon fiber reinforced resin matrix composites prepared by EEU-DDS reached 97.9 MPa, 1281 MPa, and 81.3 kJ/m2, respectively, higher than those of DGEBA-DDS. Therefore, equol-based epoxy resin can serve as an ideal alternative to petroleum-based bisphenol A-type epoxy resin, offering superior comprehensive properties.

Mechanical strength and low-velocity impact behavior of glass fiber reinforced filament wound pipes with different number of layers after hydrothermal aging

Composite pipe is preferred over metal and other materials for water supply, liquid chemical transport, and fuel and gas transport. This is because composite pipes are more corrosion resistant, have a high strength/density ratio, high stiffness/density ratio, and more durable than metal pipes. The properties of the composite pipes employed may differ based on the operating environment. Therefore, determining the properties of the composite pipe according to the working environment is extremely important for its lifespan. The thickness of the samples is increased in line with different needs (such as increased strength). Increasing the thickness of samples, especially those exposed to different environmental conditions, and investigating the changes that will occur in the physical and mechanical properties of the samples are another important situation. In this investigation, glass fiber (GFRP) reinforced epoxy composite pipes have been examined, which were manufactured using the filament winding method with different layers [±55°]. To determine their properties in different working environments, the GFRP composite pipes were subjected to hydrothermal aging in pure water at 80°C for several days (7, 14, 21, and 28). The changes in their mechanical properties under working conditions were determined through hoop tensile strength tests and low velocity impact tests applied at different energy levels. The experimental results show that the tangential stress values increased by 10.59% as the number of layers increased. As the aging time increased, the durability of the 6-layer composite pipe decreased by 17.69%. Furthermore, the ability of the aged pipes to withstand damage was evaluated, revealing that the aging process exacerbated the damage within the pipes.

Coupled extreme gradient boosting algorithm with artificial intelligence models for predicting compressive strength of fiber reinforced polymer- confined concrete

Accurately predicting and identifying appropriate parameters are necessary for producing a safe and reliable strength model of concrete elements confined with fiber-reinforced polymers (FRP). In this study, an extreme gradient boosting (XGBoost) algorithm was developed for the feature selection and prediction of the ultimate compressive strength of FRP-confined concrete. The modeling process was established using a dataset from open-source literature consisting of 490 circular columns. Three well-known artificial intelligence (AI) models, the multivariate adaptive regression spline (MARS), extreme learning machine (ELM), and RANdom Forest GEnRator (Ranger), were used to validate the proposed model. The results demonstrated the effectiveness of the XGBoost algorithm in the modeling process, selection of suitable parameters, and enhancement of the prediction accuracy. The algorithm achieved excellent prediction results for all input combinations with a coefficient of determination (R2) greater than 0.9, and the best performance is gained by using five input parameters with (R2 = 0.955), mean absolute percentage error (MAPE = 0.130), and root mean square error (RMSE = 0.572). The study revealed the flexibility and efficiency of capturing the nonlinear behavior of complex FRP-confined concrete using the proposed model.

Multivariate formulation to predict the frictional strength of fiber reinforced soils using gene expression programming

Modeling and prediction approaches have attracted much interest in recent years to evaluate the efficiency of fiber reinforcement in improving the strength characteristics of loose soils. Several analytical and artificial intelligence (AI) based models have been presented to estimate friction angle of fiber reinforced soils (FRS). However, due to limited input characteristics, these analytical models lack accuracy, whereas AI-based models are developed on advanced programming methods and need substantial programming expertise, resulting in a lack of agreement in mechanism and application. Herein, we provided a multivariate formulation that uses gene expression programming (GEP) to predict the frictional strength of FRS using fifteen influencing factors, which, to the best of our knowledge, has never been reported before. In this regard, two mathematical models are presented, one of which incorporates both qualitative and quantitative input factors, while the other just considers quantitative variables. Laboratory experimental data on FRS from various sources was assessed and properly analysed within the proposed framework while taking into account various affecting factors. The results illustrate the efficiency of GEP in estimating FRS frictional strength and emphasis the need of considering several parameters for prediction. Sensitivity and parametric studies were also performed to identify the relevance of each influencing factor and to determine whether the prediction models meet physical processes or are purely empirical relations. Finally, a user-friendly computer program was developed based on the GEP derived mathematical formulations to anticipate the FRS friction angle, which offers practitioners great field applicability.

Application of ramie-based eco-friendly material in coastal protection structures in Indonesia: feasibility study focusing on strength and biodegradability

ABSTRACT Coastal erosion presents a significant environmental threat globally, including in the Northern Java coastal area of Indonesia. As employing hard structures is not an environmentally sustainable practice, nature-based solutions, such as mangrove forests, have emerged as a global trend offering sustainable coastal protection. However, safeguarding young seedlings from wave and current forces remains challenging. Given that temporary structures, such as synthetic geo-bag dikes, considered for protection pose environmental challenges as they degrade slowly, the use of natural fibres such as ramie, unique to Indonesia as a strategic raw commodity, is a sustainable alternative. The study examined ramie fibres (0.28 mm thick) as an eco-friendly geo-bag material through laboratory tests, biodegradability burial tests, and comparisons with other natural fibres. Despite alkali treatment, the strength of ramie fibre did not meet standard geotextile parameters, and its degradability rendered it unsuitable for the expected service life. Ramie would need specific treatments to become a viable alternative for geo-bags. In conclusion, further research is needed to explore how ramie can serve as a sustainable geo-bag material.

Investigation and calculation of the longitudinal compressive strength of unidirectional glass fiber reinforced polymer considering the fiber orientation distribution

In this study, undulations and their influence on the longitudinal compressive strength of a unidirectional glass fiber reinforced polymer (GFRP) composite are investigated theoretically and experimentally. The objective of this research is to explore the failure mechanisms in FRP and to characterize the mechanical properties of FRP as a function of fiber orientation. For this purpose, a multiscale material model is developed that considers a stochastic fiber orientation distribution (FOD) and models matrix fracture-initiated failure. The relationship between compressive strength and undulation is investigated experimentally on standardized specimens made of unidirectional GFRP. The fiber orientations are measured using X-ray computed tomography and ImageJ image analysis, resulting in a binormal distribution of fiber orientations in the series of samples tested. To examine the failure process in detail, the compression tests are simulated using finite element analysis (FEA). Both the FEA results and the measured compressive strengths confirm the model assumption of matrix fracture-initiated failure under longitudinal compressive loading. The presented analytical model realistically represents the correlation of compressive strength with the FOD.

Interaction mechanisms between fibers and bubbles during foam forming

It is critical to understand the interaction mechanism of fiber-bubble before the foam-forming technique is used to disperse the long fiber and tailor the material microporous structure. Herein, the adhesion behavior of ionic and nonionic surfactants with different concentrations on five fibers was investigated, and the effect of electrostatic force and adhesion driving force on the interaction between fibers and bubbles was analyzed. In addition, the fiber dispersion mechanisms and the response mechanism of the fiber orientation and tensile strength of foam-formed paper on the interaction strength between fiber and bubble were clarified. The results show that the adhesion ability between hydrophobic fibers with weak surface polarity and cationic and amphoteric surfactants is more obvious. Though electrostatic repulsion weakens the interaction strength of fibers with anionic surfactants, the adhesion ability can exist when the adhesion driving force is larger than 6.6 mN/m. Furthermore, the bridge effect between ethoxylated surfactant headgroups with the acylamino on the aramid fiber surface also propels the adhesion behavior of bubble-fiber. The fiber dispersion mechanisms were proposed based on the adhesion effect of the fiber-bubble, electrostatic elimination, and high-viscosity (≥95 mPa∙s) properties of the “foam-fiber” slurry. Eventually, under the gradually decreased interaction strength between fibers and bubbles, the fiber orientation in the Z direction of foam-formed NBSKP fiber paper turned from −20°-20° to −60°-40°, and the tensile strength decreased from 693 KPa to 537 KPa. This work has implications for improving the long fiber dispersion and regulating the structure of foam-formed fiber composites.

Pyramiding effects of favorable haplotypes of loci on major fiber yield and quality traits in Upland Cotton (Gossypium hirsutum L.)

Enhancing both fiber yield and quality is crucial in cotton breeding programs. Typically, a negative correlation exists between fiber yield and quality, and the strategy to decouple this relationship remains obscure. In this study, we generated three multi-parent intercross populations, encompassing 2,852 F2:3 lines, which represent fiber yield potential (FY), fiber quality potential (FQ), and a combination of both potentials (FYQ), derived from sixteen diverse Upland cotton cultivars. We utilized twenty-four kompetitive allele specific PCR (KASP) molecular markers, based on previously identified loci associated with fiber quality (FL5/FS1, FL3/FS2, and FL2) and fiber yield (BW1, BW2, and LP1), for genotyping purposes. The pyramiding of favorable haplotypes from three fiber quality-associated loci resulted in an increase exceeding 10% in fiber length (FL5+FL3+FL2+LP1) and in an increase exceeding 17% in fiber strength (FL5+FL3+FL2). Notably, our findings suggest that the combination of FL3+FL2+BW1+LP1 alleles has the potential to disrupt the negative correlation between fiber yield and quality. Lines harboring these alleles simultaneously exhibited an elevated lint percentage (LP), as well as enhanced fiber length and quality. This study offers robust molecular markers for the efficient selection of superior progeny with desired phenotypes in the early stages of cotton breeding. Furthermore, the allelic combination that concurrently improves fiber quality and yield sheds light on for further exploration the molecular basis of breaking unfavorable linkages in crop breeding.

СТАНДАРТИЗАЦІЯ ЛЛЯНОЇ СИРОВИНИ: ПОРІВНЯЛЬНИЙ АНАЛІЗ ДОСВІДУ США ТА УКРАЇНИ

The main problem in the primary processing of bast fiber raw materials is Ukraine's significant lag in the field of standardization compared to the USA, which negatively affects production efficiency, product quality, and competitiveness in the global market. The article aims to provide a comprehensive comparative analysis of flax raw material quality assessment systems in Ukraine and the USA, identify the key reasons for Ukraine's lag, and develop practical solutions to address these issues. The research found that while Ukraine still relies on outdated standards for flax fiber quality evaluation, which are primarily based on organoleptic methods and do not take into account modern requirements, the USA is actively developing and implementing innovative standards that regulate a wide range of quality indicators, such as fiber fineness, strength, color, shive content, and other important parameters. The main reasons for Ukraine's lag in the field of flax standardization include persistent economic difficulties, obsolete infrastructure and equipment, insufficient funding for scientific research, and weak integration with international standardization organizations. The authors propose a set of solutions to overcome these challenges, which involve increasing state support for the flax industry, intensifying research efforts aimed at developing new methods for assessing the quality of flax raw materials, harmonizing national standards with international ones, deepening international cooperation, and fostering the development of industry associations and clusters. The article emphasizes the necessity of introducing modern instrumental methods for assessing the quality of flax raw materials, such as spectrophotometry for color measurement, computer vision systems for analyzing fiber structure, and automated methods for determining fineness and shive content. The importance of developing standards for new and innovative flax products to expand the range, improve the competitiveness of domestic products, and enter promising markets is underlined.

Development And Acceptability of Banana (Esp. Damilig-Musa Acuminata) Fiber as Alternative Source of Natural Fabric

Banana fiber yarn is a natural best fiber derived from the inner bark (or phloem) of banana plants. It is a very eco-friendly material, which also has the advantage of being completely biodegradable. This yarn is also known as banana silk, due to the shiny and silky aspect of the most precious fibers, or Musa yarn, from the Musa genre to which the banana plant belongs. The study will focus on the Development and Acceptability of Banana (Esp. Damilig-Musa Acuminata) Fiber as Alternative Source of Natural Fabric. The panel of experts will evaluate the following namely: DOST personnel, Garments instructor, fashion designer/ textile experts and Faculty and garments fashion and design students of Isabela State University – Ilagan Campus. The purpose of this research is to develop and test the effectiveness of banana (Damilig-musa acuminata), specifically its pseudo-stem. The researcher aims to unlock the following queries: 1. What are the processes used in the production of yarn? 2. What will be the outcome of the develop banana (Damilig-musa acuminata) after the process of fiber extraction in terms of texture, appearance and durability. 3. What will be the assessment and acceptability of the banana yarn (Damilig-musa acuminata) after weaving process is completed in terms of colorfastness, crease resistant and fabric shrinkage The descriptive type of research will applied in the study with the set of survey questionnaire as the main instrument in gathering data. The weighted mean will also utilizes to determine the general acceptability of the study. The study will use the five-point Likert rating scale. The process will conduct in accordance to Development and Acceptability of Banana (Esp. Damilig-Musa Acuminata) Fiber as Alternative Source of Natural Fabric. The procedures are harvesting, peeling, retting, and sun drying, grouping, spinning and weaving. Evaluation results will show that the project obtained an overall mean of 4.38 to the development of fiber and 3.45 to the level of acceptability of fabric which means that the Development and Acceptability of Banana (Esp. Damilig-Musa Acuminata) Fiber as Alternative Source of Natural Fabric is Moderately Acceptable to the panel of experts based on the criteria checklist. Based on the results of the experiments, it can be concluded that banana fibers can be used as an alternative source of natural fibers because they have several inherent advantages over cotton fiber. Because of the abundance of raw material in nature each year, banana fiber-based yarns and fabrics are less expensive and more sustainable. Because of the low fiber weight and strength loss, softening banana fibers by boiling in distilled water was found to be a better treatment.

An Eco-Friendly Approach to Preserve Goatskins Using Tamarindus Indica Leaf

Hides and skins, the main raw materials for leather industries, are traditionally preserved with sodium chloride (NaCl). Due to the excessive use of salt (around 40 to 50% w/w) in the curing process, total dissolved solids (TDS), and salinity are produced in large quantities by the soaking effluent during the leather processing. To address the resulting environmental threat from the tanneries and replace traditional curing, plant-based curing is a cutting-edge green technology. In this study, Tamarindus indica leaves were used as a combination of 5% powder + 10% salt and 10% paste + 10% salt to preserve goat skin for 28 days. The organoleptic characteristics, hydrothermal stability, moisture content, nitrogen content, and bacterial load were periodically monitored. After curing, the goatskin was processed into leather, the environmental impact of the wastewater was evaluated, and its physical and fibre strength was assessed. The TDS value, chloride content, biochemical oxygen demand, and chemical oxygen demand were reduced up to 65.62%, 69.38%, 31.08%, and 27.06% respectively. The prepared shoe-upper leather exhibited equivalent physical properties compared to the control. Scanning electron microscopy (SEM) image ensured the conformity of the fibre structure of the experimental leather with control. A significant correlation was seen among the skin preservation efficiency parameters, while the strongest correlation was (r = -0.996, p<0.001) between moisture content and shrinkage temperature. Therefore, T. indica leaves powder as well as paste could be an effective curing agent by reducing the use of salt in leather industries.