Strain Rate Research Articles

Phase reversion mediated the dual heterogeneity of grain size and dislocation density in an equiatomic CrCoNi medium-entropy alloy

An ultra-high strain rate (104 s-1) dynamic plastic deformation treatment at liquid nitrogen temperature (LNT-DPD) followed by annealing is carried out to obtain dual heterogeneity of grain size and dislocation density in an equiatomic CrCoNi medium entropy alloy (MEA). Such extreme loading conditions resulted in extensive phase transformation in this MEA. Subsequent annealing at 650°C for 1 h further induced reverse phase transformation and partial recrystallization, forming a complex heterogeneous microstructure characterized by nested trimodal grain sizes and partitioned dislocation density. A superior yield strength of ∼800MPa and a good ductility of ∼40% were simultaneously achieved in this heterogeneous alloy. In order to reveal the effects of grain size and dislocation density distributions on the mechanical property improvements, the underlying deformation mechanisms were systematically discussed. High density of geometrically necessary dislocations (GNDs) would be induced in complex heterogeneous structures during tensile deformation due to strain gradients or partitioning between different regions, which would lead to additional strengthening and work hardening. These results provide a novel approach to overcome the strength-ductility trade-off dilemma for FCC-structured MEAs.

Effect of strain rates on stress corrosion sensitivity of 7085-T7452 thick-plate friction stir welding joint

Effect of strain rates on stress corrosion sensitivity of 7085-T7452 thick-plate friction stir welding joint

A rate-dependent crack bridging model for dynamic fracture of CNT-reinforced polymers

Carbon nanotubes (CNTs) improve the fracture toughness of polymer-based matrix composites by bridging the crack growth path. This research presents a finite element (FE) rate-dependent crack bridging model of Mode-I dynamic crack growth in CNT-reinforced polymers accounting for rate of loading and rapid crack growth. Two distinct CNT bridging and matrix cracking damage mechanisms are taken into account in the fracture process zone (FPZ) accounting for the dissipation of fracture energy. A viscoelastic-viscoplastic material model is adapted for the matrix phase to capture the strain rate effects. The crack in the matrix phase is modeled using cohesive zone elements characterized by experimental data. A rate-dependent traction-separation law obtained from CNT pull-out simulation at relevant crack opening speeds is used to simulate the CNT bridging in the FPZ. Considering the given traction-separation law as a constitutive equation, the CNTs are replaced with non-linear spring elements to facilitate the FE simulation of crack bridging with numerous CNTs in the FPZ. The proposed rate-dependent FE model for crack bridging enables the study of the effect of key CNT factors such as length, orientation, waviness, volume fraction, and agglomeration on fracture energy dissipation at various crack speeds. The developed model can simultaneously consider the interactive effects of all CNT parameters which is useful for considering all processing-induced uncertainties in analyzing the effects of CNTs on the dynamic fracture toughness of nanocomposites.

Adiabatic Shear Localization in Metallic Materials: Review.

In advanced engineering applications, there has been an increasing demand for the service performance of materials under high-strain-rate conditions where a key phenomenon of adiabatic shear instability is inevitably involved. The presence of adiabatic shear instability is typically associated with large shear strains, high strain rates, and elevated temperatures. Significant plastic deformation that concentrates within a adiabatic shear band (ASB) often results in catastrophic failure, and it is necessary to avoid the occurrence of such a phenomenon in most areas. However, in certain areas, such as high-speed machining and self-sharpening projectile penetration, this phenomenon can be exploited. The thermal softening effect and microstructural softening effect are widely recognized as the foundational theories for the formation of ASB. Thus, elucidating various complex deformation mechanisms under thermomechanical coupling along with changes in temperatures in the shear instability process has become a focal point of research. This review highlights these two important aspects and examines the development of relevant theories and experimental results, identifying key challenges faced in this field of study. Furthermore, advancements in modern experimental characterization and computational technologies, which lead to a deeper understanding of the adiabatic shear instability phenomenon, have also been summarized.

Research on predicting the thermocompression deformation behavior of Mg-Li matrix composite using machine learning and traditional techniques

Artificial intelligence and machine learning (ML) technologies have emerged as powerful tools for analyzing the thermal compression deformation behavior of metal matrix composites, offering significant potential to optimize their plastic deformation processing techniques. In this study, the Al3La/LAZ532 composite based on in-situ self-reaction technology was successfully prepared by adding La2O3 particles. Then, the thermal compression flow behavior of the as-cast composite was comparatively researched using a traditional Arrhenius model and advanced machine learning methods (Linear Regression, AdaBoost, Random Forest, and XGBoost). The flow stresses were predicted under various thermal operating conditions, and the performance of all models was assessed using root mean square error (RMSE), coefficient of determination (R2) and mean absolute error (MAE). Analysis shows that the Random Forest model outperforms traditional models and other ML methods in predictive accuracy, achieving an R2 of 0.97, an MAE of 5.8, and an RMSE of 7.07. Additionally, the stable hot working zone for the composite at 300 °C and a strain rate of 0.001∼0.01 s⁻1 can be identified by combining the microscopic structure with the macroscopic hot working map. This zone is characterized by a uniformly distributed, fine-grained structure with high levels of dynamic recrystallization (DRX). The texture with the <0001> axis of the grains aligned parallel to the compression direction (CD) is formed in the thermally deformed microstructure, and the DRX mechanism is discontinuous dynamic recrystallization (DDRX).

Energy harvesting from wake-induced vibration of flexible flapper behind a bluff body

Piezoelectric energy harvesting from ambient vibrations offers a promising small-scale energy generation strategy, with wake-induced vibration of flexible structures being an ideal candidate. This study examines a bluff body followed by a fully flexible piezoelectric flapper in a viscous free-stream flow using an in-house discrete forcing immersed boundary method-based fluid-structure-electric energy solver for parametric investigation. Different vortex shedding regimes are identified based on vortex formation around the flexible flapper. The complex and interdependent spatiotemporal dynamics of the wake and flexible body dictated by parameters such as bending rigidity and the gap space between the flapper and bluff body result in various deformation profiles, influencing the strain rate and output power. The study also investigates the independent variation of flapper length and its impact on vortical arrangements and flexibility, introducing different oscillation modes. The present study takes a nuanced view of the overall dynamics and their mutual effect on the power output, unlike most existing studies where enhancing the amplitude and frequency of oscillations for an optimal output was the main concern. Factors such as flapper curvature, its asymmetry, and periodicity have been especially highlighted in the context of the output and the corresponding parametric spaces investigated. Interestingly, the increase in piezo-flapper length has seen a reduction in output, though it was instrumental in bringing symmetry back. The study offers comprehensive insights into ideal harvesting regimes and the underlying dynamical mechanisms and can contribute toward the design of future energy harvesting devices.

Effect of deformation and cooling on non-equilibrium microstructure evolution and phase-transition mechanism of Ti–6Al-2.5Mo-1.5Cr-0.5Fe-0.3Si

In the process of non-isothermal deformation of titanium alloy, the microstructure evolution is very complicated, which has direct effect on the properties of the titanium alloy. This study examines the effects of pure cooling and coupled deformation and cooling at the initial temperature of 940 °C and the cooling rate of 5,50 °C/s, and the strain rate of 0.1, 10s−1 respectively, on the microstructure evolution of Ti–6Al-2.5Mo-1.5Cr-0.5Fe-0.3Si alloy (TC6) were investigated. The microstructure after cooling was characterised, and the mechanism of non-isothermal deformation on microstructure evolution and the mechanism of secondary α phase (αs) precipitation were revealed. The results show that the secondary α phase precipitates in large quantities after cooling to a certain temperature, and the secondary precipitated has an obvious inhibiting effect on the diffusion growth of the primary α phase (αp). Secondary α phases can be divided into lamellar and equiaxial types. When the temperature drops sharply, the fine secondary α phase can be precipitated directly from the β matrix. Due to the large number of dislocations generated by the deformation, many small secondary α phases can be generated during the rapid cooling process. The orientation relationship between α phase and β matrix is destroyed by the deformation, resulting in a weakening of the anisotropy, so that the secondary α phase remains equiaxial during the precipitation process.

Time-dependent constitutive behaviors of a dynamically crosslinked glycerogel governed by bond kinetics and chain diffusion

Soft materials featuring dynamic networks represent a burgeoning frontier in materials science, offering multifaceted applications spanning soft robotics, biomaterials, and flexible electronics. Unraveling the time-dependent constitutive behavior of these materials, rooted in dynamic networks, stands as a pivotal pursuit for engineering advancements. Herein, we fabricate a tough and extreme-temperature-tolerant glycerogel with a polymer network crosslinked by metal-coordination crosslinkers and conduct a thorough analysis of its intricate mechanical responses across monotonic loading, relaxation, creep, and cyclic tests. We then develop a physically grounded constitutive model integrating the dynamics of crosslinker association/dissociation and polymer chain diffusion, furnishing a holistic framework to elucidate their interplay. We employ a statistical description, using density functions of chains in terms of end-to-end vectors, to characterize network reconfiguration. The evolution of chain density under external load, mediated by crosslinker kinetics and chain diffusion in a viscous medium, leads to intriguing variations in elastic energy and stress responses. Through meticulous experimental validation and numerical simulations, we demonstrate the efficacy of the model in forecasting the mechanical behavior of dynamic polymer networks under diverse loading scenarios, encompassing strain rate effects, stress relaxation, Mullins effect, and self-recovery phenomena. Our findings provide valuable insights into the design and optimization of dynamic network-based materials for diverse applications in biomedical and engineering fields.

Cardiopulmonary Physiology of Hypoxemic Respiratory Failure among Preterm Infants with Septic Shock

To examine cardiopulmonary physiological alterations associated with hypoxemic respiratory failure (HRF; fraction of inspired oxygen ≥0.60) among preterm neonates requiring vasopressors/inotropes during sepsis (septic shock). We conducted a retrospective cohort study from 2015 through 2022 at a tertiary neonatal intensive care unit. Neonates <34 weeks gestational age who had septic shock and underwent a comprehensive targeted neonatal echocardiography (TNE) ≤72 hours of sepsis onset were included. TNE findings of patients with shock and HRF were compared with those with shock without HRF. Indices of pulmonary vascular resistance (PVR), right (RV) and left (LV) ventricular systolic and diastolic function, measured using conventional, tissue Doppler imaging and speckle-tracking echocardiography, were examined. Of 52 included infants with septic shock, 19 (37%) also had HRF. Baseline characteristics were similar. On TNE, although the HRF group more frequently had bidirectional/right-to-left flow across the patent ductus arteriosus (67% vs. 33%; p=0.08), all indices of PVR and RV function were similar. However, the HRF group demonstrated reduced LV systolic function [ejection fraction: 51.8±12.3 vs. 62.6±13.0%; global peak systolic longitudinal strain -15.2±4.5 vs. -18.6±4.5%], diastolic function [early (2.3±1.0 vs. 3.6±1.2 /s) and late (2.4 (1.9, 2.6) vs. 2.8 (2.3, 3.5) /s diastolic strain rate], and higher frequency of LV output <150 ml/min/kg (44 vs. 12%); all p<0.05. Acute HRF occurring in preterm neonates with septic shock is associated with alterations in TNE measures of LV function, and not PVR or RV function. Future studies should evaluate the impact of supporting LV function in these patients.

Comparison of hydrogen effects on additively manufactured and conventional austenitic steels

Hydrogen and its derivatives are promising energy carriers for future renewable energy supplies. Austenitic stainless steels, such as AISI 316L, are commonly used in hydrogen transportation systems. While often thought to be resistant to hydrogen embrittlement, studies have shown that 316L is susceptible under certain conditions. As demand for hydrogen applications grows, additive manufacturing (AM) technologies offer design flexibility and customisation benefits. However, data on AM parts behaviour in hydrogen environments is lacking. This study investigates the influence of hydrogen on mechanical properties using slow strain rate testing (SSRT) on conventional AISI 304L, 316L and AM 316L specimens. The results indicate a greater effect of hydrogen on 304L compared to 316L, with AM 316L showing increased susceptibility. However, the ductility of AM 316L remains comparable to conventional 316L due to its initial ductility. The study provides insights into the performance of conventional and AM austenitic stainless steels in gaseous hydrogen environments.

Influence of Strain Rate on Barkhausen Noise in Trip Steel.

This paper deals with Barkhausen noise in Trip steel RAK 40/70+Z1000MBO subjected to uniaxial plastic straining under variable strain rates. Barkhausen noise is investigated especially with respect to microstructure alterations expressed in terms of phase composition and dislocation density. The effects of sample heating and the corresponding Taylor-Quinney coefficient are considered as well. Barkhausen noise of the tensile test is measured in situ as well as after unloading of the samples. In this way, the contribution of external and residual stresses on Barkhausen noise can be distinguished in the direction of tensile loading, as well as in the transversal direction. It was found that the in situ-measured Barkhausen noise grows in both directions as a result of tensile stresses and the realignment of domain walls. The post situ-measured Barkhausen noise drops down in the direction of tensile load due to the high opposition of dislocation density at the expense of the growing transversal direction due to the prevailing effect of the realignment of domain walls. The temperature of the sample remarkably grows along with the increasing strain rate which corresponds with the increasing Taylor-Quinney coefficient. However, this effect plays only a minor role, and the density of the lattice imperfection expressed especially in terms of dislocation density prevails.

Models for the Design and Optimization of the Multi-Stage Wiredrawing Process of ZnAl15% Wires for Spray Metallization.

Metallization, a process for applying anti-corrosion coatings, has advantages over hot-dip galvanizing, such as reduced thermal stress and the ability to work "in situ". This process consists of the projection of a protective metal as coating from a wire as application material, and this wire is obtained by multi-stage wiredrawing. For the metallization process, a zinc-aluminum alloy wire obtained by this process is used. This industrial process requires multiple stages/dies of diameter reduction, and determining the optimal sequence is complex. Thus, this work focuses on developing models with the aim of designing and optimizing the wiredrawing process of zinc-aluminum (ZnAl) alloys, specifically ZnAl15%, used for anti-corrosion applications. Both analytical models and numerical models based on the finite element method (FEM) and implemented by computer-aided engineering (CAE) software Deform 2D/3D v.12, enabled the prediction of the drawing stress and drawing force in each drawing stage, producing values consistent with experimental measurements. Key findings include the modeling of the material behavior when ZnAl15% wires were subjected to the tensile test at different speeds, with strain rate sensitivity coefficient m = 0.0128, demonstrating that this type of alloy is especially sensitive to the strain rate. In addition, the optimal friction coefficient (µ) for the drawing process of this material was experimentally identified as µ = 0.28, the ideal drawing die angle was determined to be 2α = 10°, and the alloy's deformability limit has been established by a reduction ratio r ≤ 22.5%, which indicates good plastic deformation capacity. The experimental results confirmed that the development of the proposed models can be feasible to facilitate the design and optimization of industrial processes, improving the efficiency and quality of ZnAl15% alloy wire production.

Impact resistance study of lime slag–stabilised steel slag mixes

ABSTRACT Given the transient nature of impact loading, exploring the microscopic damage characteristics and damage mechanisms of materials through indoor tests is difficult. In this study, the damage morphology and energy dissipation characteristics of lime slag–stabilised steel slag (LSSS) mixes under vertical impact loading is explored using ABAQUS software, a finite element model of LSSS for falling hammer impact test is established, the validity of finite element calculation is verified by comparing the results of indoor tests, and the strain characteristics, deflection changes, and energy transformation process of LSSS under vertical impact loading are analysed. Results show that the LSSS tensile and compressive strains under impact loading are roughly divided into low strain rate, precracking, and cracking phases with a rapid increase in strain. Under the same impact energy conditions, the LSSS bottom tensile strain, span deflection, drop hammer kinetic energy conversion time, and LSSS plastic energy consumption curve rising slope are sensitive to drop hammer mass. Thus, improvement in drop hammer mass will prolong the impact loading of the drop hammer–LSSS system internal energy conversion time, and the LSSS strain peak range to the central concentration, enhancing span deflection and bottom deformation.

Direct calculation of the eddy viscosity operator in turbulent channel flow at Re τ = 180

This study aims to quantify how turbulence in a channel flow mixes momentum in the mean sense. We applied the macroscopic forcing method (Mani &amp; Park, Phys. Rev. Fluids, 2021, 054607) to direct numerical simulation (DNS) of a turbulent channel flow at $Re_\tau =180$ using two different forcing strategies that are designed to separately assess the anisotropy and non-locality of momentum mixing. In the first strategy, the leading term of the Kramers–Moyal expansion of the eddy viscosity is quantified, revealing all 81 tensorial coefficients that essentially characterise the local-limit eddy viscosity. The results indicate the following: (1) the eddy viscosity has significant anisotropy, (2) Reynolds stresses are generated by both the mean strain rate and mean rotation rate tensors associated with the momentum field and (3) the local-limit eddy viscosity generates asymmetric Reynolds stress tensors. In the second strategy, the eddy viscosity is quantified as an integration kernel revealing the non-local influence of the mean momentum gradient at each wall-normal coordinate on all nine components of the Reynolds stresses over the channel width. Our results indicate that while the shear component of the Reynolds stress is reasonably reproduced by the local mean gradients, other components of the Reynolds stress are highly non-local. These results provide an understanding of anisotropy and non-locality requirements for closure modelling of momentum transport in attached wall-bounded turbulent flows.

Cardiac function at follow-up in infants treated with therapeutic hypothermia for neonatal hypoxic-ischemic encephalopathy.

Compromised myocardial function and persistent elevated pulmonary vascular resistance are common among neonates treated with therapeutic hypothermia (TH) for hypoxic-ischemic encephalopathy (HIE). There is a lack of data regarding persistence of cardiac alterations after discharge from the neonatal intensive care unit (NICU). We assessed cardiovascular profiles after NICU discharge. Echocardiogram data, including speckle-tracking echocardiography (STE), were extracted from the latest outpatient scan. Data were compared by initial amplitude-integrated encephalography (aEEG) profiles on admission [normal vs. abnormal]. In total, 70 (19%) neonates had a follow-up echocardiogram (22 with initial normal aEEG, 48 with abnormal aEEG). Age at follow-up was similar between the two groups (6.2 vs. 7.7 months, [p = 0.08]). Neonates with an initially abnormal aEEG showed more negative Right Ventricle (RV)-peak global longitudinal strain (-28.2 vs. -26.0%, [p = 0.02]), RV-peak free wall longitudinal strain rate (-1.24 vs. -1.10 [1/second], [p = 0.01]), and RV-peak free wall longitudinal strain rate (-1.50 vs. -1.27 [1/second], [p = 0.001]). These associations remained after multilinear regression analysis, indicating persistent enhanced RV contraction in the abnormal aEEG group. Neonates with initial abnormal aEEG profiles exhibited increased RV contraction after NICU discharge. Future studies should explore long-term cardiovascular follow-up of neonates with HIE, beyond the perinatal period. What is the key message of your article? Cardiac performance in hypoxic ischemic encephalopathy is linked to adverse outcomes. Survivors with an abnormal aEEG at admission showed increased right ventricular contractility at follow-up, possibly related to an adverse adaptation to the initial insult. What does it add to the existing literature? This study offers insights into long-term cardiovascular outcomes in neonates with HIE, focusing on the link between initial aEEG abnormalities and later RV function. What is the impact? The findings underscore the importance of early cardiovascular assessments and monitoring in neonates undergoing TH for HIE, potentially guiding future follow-up protocols.

Dynamic Mechanical Properties and Constitutive Modeling of Polyurethane Microporous Elastomers.

The present study fabricated samples of polyurethane elastomers (PUEs) with three distinct densities and assessed their mechanical responses using split Hopkinson pressure bar (SHPB) tests. The findings reveal a significant increase in PUE stress with increasing strain rate and density. To further investigate the influence of strain rate sensitivity on PUEs, a strain rate sensitivity coefficient was employed to quantify the impact of strain rate on the mechanical properties of PUEs. Separate quantifications were performed for collapse stress, plateau stress, and densification strain as indicators of the strain rate sensitivity coefficient. The results demonstrate that the collapse stress sensitivity coefficient was notably affected by the applied strain rate. Additionally, both collapse and plateau stresses exhibited an increase with increasing density, which could be described by a power function relationship. Based on the theory of strain energy function, a constitutive model considering density and strain rate effects was developed to describe the stress-strain behavior of PUEs under various densities and strain rates. A comparison between this constitutive relationship and experimental results showed good agreement, highlighting its potential in describing dynamic mechanical behavior.

Effect of creep fracture mode transition of P91 steel welded joints on long-term creep fracture life

The formation mechanism of the two fracture behaviors and their effects on the creep life of P91 steel welded joints during creep were investigated, and the morphology and microstructure of the two fractures were characterized by SEM and EBSD, and the results were as follows: the change of fracture modes was affected by the creep strain rate and cavity nucleation rate in the joint. When the applied stress is large, the creep strain rate of BM is higher, and brittle fracture occurs at BM; when the applied stress is low, the cavity nucleation rate of FGHAZ is higher, and brittle fracture occurs at FGHAZ, known as type IV cracking. The occurrence of type IV cracking will reduce the accuracy of creep life prediction methods, and life prediction considering fracture mode can effectively improve the prediction accuracy.

Mechanical Responses and Deformation Mechanisms of Low-cost High-entropy Alloy AlCrFe2Ni2 with Heterogeneous Structure Subjected to High Strain Rate Deformation

Mechanical Responses and Deformation Mechanisms of Low-cost High-entropy Alloy AlCrFe₂Ni₂ with Heterogeneous Structure Subjected to High Strain Rate Deformation

Normal ranges of left atrial phasic strains and strain rates by 2D speckle-tracking echocardiography in pediatrics: a systematic review and meta-analysis

Establishing normal values of left atrial (LA) phasic strains and strain rates is essential for distinguishing between normal and abnormal functions, determining the degree of abnormality, and understanding the clinical significance of reported values in pediatrics. This meta-analysis aimed to establish normal values of two-dimensional speckle-tracking echocardiography (2DSTE)-derived LA phasic strains and strain rates in the pediatric population and identify the sources of inter-study heterogeneity for these values. A comprehensive search of PubMed, Scopus, and Embase databases was conducted using keywords such as “left atrial/left atrium,” “strain/speckle/deformation,” and “echocardiography” combined with pediatric age categories. Inclusion criteria comprised English-language human studies involving healthy subjects under 18 years of age. Subjects were categorized as neonates (up to 1 month), infants (1–12 months), and children (1–18 years). A random-effects model was applied to determine 2DSTE-derived LA strains and strain rates, and a meta-regression analysis was performed to investigate inter-study heterogeneity. Our analysis included 17 studies involving 1448 healthy subjects. For children, the mean values of LA strains during the reservoir, conduit, and contraction phases were 47.3% (95% CI 42.5–52.1%), 32.8% (95% CI 27.8–37.8%), and 12% (95% CI 10.0–14.1%), respectively. The mean values for LA strain rates were 2.4 s−1 (95% CI 1.1–3.8 s−1), 4.3 s−1 (95% CI 0.6–8.0 s−1), and 2.4 s−1 (95% CI 0.4–4.5 s−1), respectively. Inter-study heterogeneity for 2DSTE-derived LA phasic strains and strain rates was attributed to factors such as the number of study participants, publication year, software utilized, gating methods, the number of analyzed segments, the geographical region of the study, and heart rate. This study established the normal range of 2DSTE-derived LA phasic strains and strain rates. Additionally, inter-study heterogeneity was found to be influenced by various demographic, physiologic, and methodological factors.

Study on Impact Resistance of Alkali-Activated Slag Cementitious Material with Steel Fiber

Alkali-activated slag cementitious materials (AASCMs) use alkaline activators to activate blast furnace slag and waste slag to replace traditional Portland cement, which can reduce CO2 emissions. An impact resistance test and scanning electron microscopy (SEM) microscopic performance analysis of alkali-activated slag cementitious material specimens with four different steel-fiber contents are performed. The effects of steel-fiber volume content and strain rate on the dynamic elastic modulus Ed, dynamic compressive strength σd, dynamic peak compressive strain εc, and energy absorption of the AASCM-SS are studied. The results indicate that the dynamic elastic modulus Ed, dynamic compressive strength σd, and energy absorption of the AASCM-SS increase with the increase of strain rate, and the dynamic peak compressive strain εc decreases with the increase of strain rate. The dynamic elastic modulus Ed, dynamic compressive strength σd, and dynamic peak compressive strain εc of the SS-AASCM increase first and then decrease with the increase of steel-fiber content. When the steel-fiber content is 0.5%, the σd and εc of the AASCM-SS are the highest, increased by 9.9% and 19.3%. The energy absorption of AASCM-SS increases with the increase of steel-fiber content. A dynamic constitutive model of the FR-AASCM considering the influence of damage, strain rate, and steel-fiber volume fraction is established. The proposed constitutive model is in acceptable agreement with the experimental AASCM-SS dynamic stress–strain curve, and the correlation coefficient is 0.91.