Storage Reservoir Research Articles

Charakterystyka złoża formacji Baharyia, pola naftowe Neag-1, 2 i 3, Pustynia Zachodnia, Egipt

An integration was achieved between different bore holes and laboratory measured data using several petrophysical parameters of the Baharyia Formation encountered in Neag-1,2&3 oil fields. It illustrates the key control factors affecting the Baharyia reservoir quality. The obtained petrophysical relationships could be used widely in both exploration geophysics and hydrocarbon reservoir production. It provides and demonstrates solutions for both geological and geophysical engineering problems. The measured porosity and permeability are ranging from 2.5 to 32 % and 0.005 to 874 mD respectively. The influence of diagenesis on both reservoir porosity and permeability has been investigated. Pore filling minerals has been classified into four classes by XRD- analysis technique. A reliable regression equation was reached between reservoir permeability and mineral pore fillings. Several relationships among rock permeability, porosity and density obtained from open hole logs were recognized. The pore throat distribution has been laboratory measured by use of MICP technique for some selected samples. The calculated reservoir storage and flow capacity indicate four major fluid flow types which are controlled by the variations in reservoir pore space framework. Formation resistivity factor – porosity relation was accomplished under reservoir conditions, while the Archie’s 2nd equation was outlined. The Archie’s parameters (a, m &n) were calculated for shaly and clean sandstones of the Baharyia Formation. Both cation exchange capacity (CEC), Mounce potential (MP) and mercury injection capillary pressure (MICP) were measured to distinguish reservoir facies.

Optimal multi-period source-sink matching in carbon capture, utilization, and storage (CCUS) systems under neutrosophic environment

Carbon capture, utilization, and storage (CCUS) is an important technology for mitigating the effect of climate change. It involves the capture of CO2 from a point source, transport it through pipelines and store it in geological reservoirs for permanent storage. CCUS enables the use of fossil fuel-based power plant sources that produce a steady amount of energy and the reduction of CO2 emissions from these sources simultaneously. While CO2 sources are easy to characterize, the storage parameters of geological reservoirs are more difficult to measure, thus, estimates are provided and used for planning large-scale CCUS systems. CO2 utilization can provide a means to delay CO2 emissions by converting it highly valuable products, however, its sequestration potential is highly uncertain. A systematic mathematical approach is needed to effectively plan CCUS systems considering the risks associated with the estimates in the characteristics of the geological reservoir and the sequestration benefits from CO2 utilization. In this study, an optimization model is developed for planning multi-period CCUS systems under neutrosophic environment. The model considers managing storage risk by maximizing satisfaction from minimizing risks, minimizing dissatisfaction from consequences brought by these risks, and minimizing indeterminacy from inaccuracy of storage characteristics estimates. For utilization, the model considers the satisfaction for CO2 utilization benefits, dissatisfaction for opportunity losses, and indeterminacy in sequestration potential. Two case studies are used to illustrate the model where a sensitivity analysis is performed to illustrate the effect of the different risk appetite on the optimal solution. These cases studies reveal important insights on scheduling operations between CO2 sources and sinks and the allocation of captured CO2 for storage and utilization. The model can be used to develop policies for considering the risks associated with these uncertainties and how it will be managed.

Optimization of CO2 flooding under dual goals of oil recovery and CO2 storage: Numerical case studies of the first-ever CCUS pilot in Changqing oilfield

CCUS (CO2 capture, utilization, and storage) is an important way to reduce carbon emissions and is increasingly applied in the development of hydrocarbon resources. It is crucial to develop proper engineering parameters to achieve the dual goals of enhanced oil recovery (EOR) and CO2 storage. This paper reports systematic numerical case studies of the first-ever CCUS pilot project at Changqing Oilfield to identify further improvement opportunities compared to the current development strategy. The targeted reservoir is located in the Huang 3 (H3) block and is characterized by ultra-low permeability (<1 mD), low oil production (<5 tons/day), and miscible and near-miscible flooding. A three-phase compositional reservoir model is established and a typical well group, consisting of one injector and eight producers, is selected to perform the numerical case studies. We investigate the influence and sensitivity analysis of engineering parameters on oil production and CO2 storage in ultra-low permeability sandstone reservoirs. The results indicate that the well pattern, the timing of switching to water-alternating-gas injection, the gas-water slug size ratio, and the injection rate are controlling factors to achieve favorable performance. The simulation results show that by using optimized engineering parameters, the oil recovery factor of the target reservoir is significantly increased by 25% and the CO2 storage efficiency is increased by 60%. Finally, an optimized development plan is obtained based on the actual conditions of the target reservoir. The reported case studies are supposed to provide insights into the optimal design and operation of CO2 utilization and storage in hydrocarbon reservoirs.

Reducing Sedimentation in Catchment Areas as Part of the Revitalization Efforts at Batujai Reservoir in Central Lombok

This research discusses efforts to revitalize the Batujai Reservoir in Central Lombok with a focus on sedimentation problems. Batujai Reservoir has a strategic role in meeting water needs in the surrounding area, but faces serious challenges due to significant sedimentation. In addition to assessing the effects of these changes on the reservoir's benefits�such as irrigation, flood control, and electricity production�this study intends to examine the effects of land use changes in the Dodokan Sub-Watershed Catchment Area (DTA) on the features and volume of sedimentation entering the reservoir. In addition, this study attempts to develop suggestions for efficient sedimentation management plans in order to increase the Batujai Reservoir's service life. Research methods include primary and secondary data collection, sedimentation modeling using the Water and Tillage/Sediment Delivery Model (WATEM/SEDEM), to evaluate the impact of sediment control structures such as check dams. Research variables include catchment area, population, annual rainfall, average daily evaporation, mainstay surface water availability, land surface erosion rate, sediment volume deposited in the reservoir, effective age of the Batujai Reservoir, and changes in land use in the Dodokan Sub-watershed. The results of this research will provide a better understanding of the main sources of sedimentation in the Batujai Reservoir and the impact of land use changes on the reservoir. It is hoped that the recommendations for sedimentation management strategies resulting from this research will help maintain reservoir storage capacity, which is important for meeting various water needs in the region.

CO2 rock physics modeling for reliable monitoring of geologic carbon storage

Monitoring, verification, and accounting (MVA) are crucial to ensure safe and long-term geologic carbon storage. Seismic monitoring is a key MVA technique that utilizes seismic data to infer elastic properties of CO2-saturated rocks. Reliable accounting of CO2 in subsurface storage reservoirs and potential leakage zones requires an accurate rock physics model. However, the widely used CO2 rock physics model based on the conventional Biot-Gassmann equation can substantially underestimate the influence of CO2 saturation on seismic waves, leading to inaccurate accounting. We develop an accurate CO2 rock physics model by accounting for both effects of the stress dependence of seismic velocities in porous rocks and CO2 weakening on the rock framework. We validate our CO2 rock physics model using the Kimberlina-1.2 model (a previously proposed geologic carbon storage site in California) and create time-lapse elastic property models with our new rock physics method. We compare the results with those obtained using the conventional Biot-Gassmann equation. Our innovative approach produces larger changes in elastic properties than the Biot-Gassmann results. Using our CO2 rock physics model can replicate shear-wave speed reductions observed in the laboratory. Our rock physics model enhances the accuracy of time-lapse elastic-wave modeling and enables reliable CO2 accounting using seismic monitoring.

Complementarity for Wind Power in Turkey: A Correlation Analysis Using XGBoost

Generation from resources such as wind power and photovoltaics are highly variable and relatively unpredictable. This variability has its own cost such that when the wind and photovoltaics happen to be low due to weather conditions, some other energy source should substitute them to satisfy the demand via market forces. The question is, to which extent does the thermal leg or the reservoir storage hydropower plants fill or substitute the gap in such cases? This is examined in the literature as the complementarity between the variable renewables and alternative sources of energy. For the purpose of answering this question, using hourly data for the period between 2015 and 2020 from Turkey, generation from the thermal leg and generation from reservoir storage hydropower plants are predicted with XGBoost, a machine learning algorithm, for different price and generation levels of wind power. The results point to a positive correlation between wind and reservoir storage hydropower, which concludes as the absence of complementarity between wind power and reservoir storage hydropower for the Turkish case. We comment that the feed-in-tariff system which guaranteed a price in US dollar terms per KwH of energy from reservoir storage hydropower decreased the incentives for substitution of wind power, cancelling out the balancing function of the reservoir storage hydropower. On the other hand, for positive prices, the natural gas fueled plants seem to substitute %63-%116 of the loss in wind power and the rest of the thermal leg happens to substitute %43-%59 of the loss in wind power, according to our calculations. These results point to a complementarity (over-substitution in this case) between wind power and the thermal leg.

Petrographic and Geochemical Evidence for a Complex Magmatic Plumbing System beneath Bagana Volcano, Papua New Guinea

Abstract Bagana is a persistently active stratovolcano located on Bougainville Island, Papua New Guinea. Characteristic activity consists of prolonged lava effusion over months to years, with occasional shifts to explosive vulcanian or sub Plinian eruptions that threaten surrounding communities. Satellite observations have shown that Bagana is a major SO2 emitter, particularly during eruptive intervals. Despite persistent and potentially hazardous activity, no previous geophysical, petrological, or geochemical studies have constrained the magma storage conditions and reservoir processes at Bagana. To address this knowledge gap, we present new bulk rock major, trace element, and radiogenic isotope data, plus mineral phase major element compositions, for Bagana lavas erupted in 2005 and 2012 and ash erupted in 2016. We use our new data to understand the magmatic processes controlling the typical effusive activity and provide the first estimates of magma storage conditions beneath Bagana. The basaltic andesite bulk rock compositions (56–58 wt% SiO2) of our Bagana lavas reflect accumulation of a plagioclase + clinopyroxene + amphibole + magnetite + orthopyroxene crystal cargo by andesitic-dacitic (57–66 wt% SiO2) carrier melts. Constraints from clinopyroxene and amphibole thermobarometry, amphibole hygrometry, and experimental petrology suggest that the high-An plagioclase + clinopyroxene + amphibole + magnetite assemblage crystallizes from basaltic-basaltic andesite parental magmas with &amp;gt;4 wt% H2O, over a temperature interval of ~1100–900°C, at pressures of ~130–570 MPa, corresponding to ~5–21 km depth. Continued crystallization in the magma storage region at ~5–21 km depth produces andesitic to dacitic residual melts, which segregate and ascend towards the surface. These ascending melts entrain a diverse crystal cargo through interaction with melt-rich and mushy magma bodies. Degassing of carrier melts during ascent results in crystallization of low-An plagioclase and the formation of amphibole breakdown rims. The radiogenic isotope and trace element compositions of Bagana lavas suggest that parental magmas feeding the system derive from an enriched mantle source modified by both slab fluids and subducted sediments. Our findings suggest that the prolonged lava effusion and persistently high gas emissions that characterise Bagana’s activity in recent decades are sustained by a steady state regime of near-continuous ascent and degassing of magmas from the crustal plumbing system. Our characterisation of the Bagana magmatic plumbing system during effusive activity provides a valuable framework for interpreting ongoing monitoring data, and for identifying any differences in magmatic processes during any future shift to explosive activity.

Research and Application of Temporary Plugging Agent Technology for High-Pressure Wells in Gas Storage Facilities

Before various construction of gas storage well, in order to ensure safety, the reservoir must be temporarily blocked, degassed by circulation and no gas in the well can be operated. There are many temporary plugging methods for oil and gas wells. This paper studies the more advanced micro mesh gel temporary plugging technology in the industry and its application in gas storage wells, which mainly solves the problems of poor degradation backflow effect and difficult permeability recovery caused by weak formation stability after temporary plugging of gas storage wells. Research points: (1) On the basis of ordinary gel, through the fusion with cross-linking agent with special structure, a micron network polymer with significant steric hindrance effect on water molecules is finally formed, which improves the strength and stability of the gel system. (2) Add hexamethylene tetramine, bisphenol propane, delayed cross-linking agent and stabilizer into the polymer aqueous solution. It is verified by laboratory tests that the micron mesh gel can be formed after constant temperature coagulation for 3h~70h at ambient temperature of 90°C~170°C. (3) The temperature resistance, permeability and gel breaking of micron mesh gel are tested in the laboratory, and the results can meet the construction requirements. (4) After the temporary plugging operation of Well Su 49K-2X in the gas storage reservoir of Huabei Oilfield is completed, the degradation products of gel breaking will flow back smoothly to ensure that the well can be put into normal injection and production quickly. The test results show that: (1) Micron mesh gel has the advantages of long plugging validity, high temperature resistance, low viscosity after gel breaking, no residue, thorough gel breaking, no formation plugging pollution, and no impact on the original reservoir permeability. It is a new green plugging technology suitable for deep buried high-temperature depleted oil and gas reservoirs. (2) Before construction, the well temperature shall be measured to conduct test injection, so as to prevent gas invasion from affecting the construction effect. The pump injection displacement is designed to be redundant, so as to prevent the low molecular solution from not reaching the design position in the well on time, and the formation of solid rubber plugs at other positions in the well from affecting the construction.

Assessing the effectiveness of reservoir operation and identifying reallocation opportunities under climate change

Reservoirs are designed and operated to mitigate hydroclimatic variability and extremes to fulfill various beneficial purposes. Existing reservoir infrastructure capacity and operation policies derived from historical records are challenged by hydrologic regime change and storage reduction from sedimentation. Furthermore, climate change could amplify the water footprint of reservoir operation (i.e. non-beneficial evaporative loss), further influencing the complex interactions among hydrologic variability, reservoir characteristics, and operation decisions. Disentangling and quantifying these impacts is essential to assess the effectiveness of reservoir operation under future climate and identify the opportunities for adaptive reservoir management (e.g. storage reallocation). Using reservoirs in Texas as a testing case, this study develops data-driven models to represent the current reservoir operation policies and assesses the challenges and opportunities in flood control and water supply under dynamically downscaled climate projections from the Coupled Model Intercomparison Project Phase 6. We find that current policies are robust in reducing future flood risks by eliminating small floods, reducing peak magnitude, and extending the duration for large floods. Current operation strategies can effectively reduce the risk of storage shortage for many reservoirs investigated, but reservoir evaporation and sedimentation pose urgent needs for revisions in the current guidelines to enhance system resilience. We also identify the opportunities for reservoir storage reallocation through seasonal-varying conservation pool levels to improve water supply reliability with negligible flood risk increase. This study provides a framework for stakeholders to evaluate the effectiveness of the current reservoir operation policy under future climate through the interactions among hydroclimatology, reservoir infrastructure, and operation policy.

Bathymetric survey and volumetric analysis of Bakolori dam reservoir North West Nigeria

Many approaches have been devised for measuring water depth in bathymetric surveys, which are used to assess sediment deposited directly in lakes and reservoirs. This technique is mostly used to calculate the reservoir's capacity and the amount of sedimentation that occurs there. The results of the volumetric analysis and bathymetric survey of the Bakolori Dam reservoir, which is situated in Northwestern Nigeria, are presented in this work. During this investigation, the differential Global Positioning System receiver (GPS), automatic level measuring tool, echo-sounder, and engine boat were utilized. ArcGis 10.0 was used to analyze the acquired data. In order to evaluate the reservoir capacity loss during the Bakolori reservoir's operating period as of 1983, the designed computed reservoir capacity was compared with the current bathymetry survey. At a spillway crest elevation of 334 meters above mean sea level (amsl), the reservoir's initial capacity is reported as 430 million cubic meters (MCM). However, the capacity has since been revised to 291 meters at the same level, with a volume change of 139,269,495 m3. As a result, the reservoir's volume changed by approximately 139 MCM during a thirty-five (35) year period of service, representing a loss of storage capacity, while the annual siltation rate was around 3,979,128 m3/a. This indicated that 33% of the reservoir's storage capacity had silted up. This is demonstrated by the aquatic weeds that have grown to a height of 334.21 meters on the lake's surface, rising from the lakebed. Therefore, to prevent total siltation, the dam reservoir needs to be adequately dredged.

Session 21. Oral Presentation for: Modelling CO2 storage in oil and gas reservoirs in the Gippsland Basin

Session 21. Oral Presentation for: Modelling CO2 storage in oil and gas reservoirs in the Gippsland Basin

Application of artificial countermeasures to enhance desilting efficiency in a reservoir under normal and extreme events

ABSTRACT The influx of flood-induced turbidity flows with high sediment concentrations into the reservoir can create sediment deposition issues, potentially jeopardizing water supply reliability. Efficient management of reservoir water resources is imperative for sustainable utilization. Evaluating the need for reservoir desilting involves comprehending the inflow and outflow dynamics of water-sediment discharges, the capacity of existing outlet structures, reservoir operation objectives, and available desilting technologies. However, given the altering hydrological conditions due to the impacts of climate change, there is a necessity for adaptive methods to ensure reservoir storage maintenance. Consequently, this study introduces the utilization of a flushing channel with artificial guiding structures to enhance desilting efficiency. A 2D numerical model offers convenient computational tools for assessing water-sediment transport behaviors across various operational scenarios based on reservoir management strategies. Data obtained from field observations is collected and analyzed to calibrate and verify the numerical model. By employing 2D numerical modeling, sediment concentration and desilting efficiency are calculated to support effective desilting operations within a reservoir. Simulation results indicate that the integration of additional artificial guiding structures at the bottom of the reservoir can enhance sedimentation mitigation outcomes by approximately 17.63% under normal conditions and by 5.27% under extreme hydrological conditions.

Evolution of CO2 Storage Mechanisms in Low-Permeability Tight Sandstone Reservoirs

Understanding the storage mechanisms in CO2 flooding is crucial, as many carbon capture, utilization, and storage (CCUS) projects are related to enhanced oil recovery (EOR). CO2 storage in reservoirs across large timescales undergoes the two storage stages of oil displacement and well shut-in, which cover multiple replacement processes of injection–production synchronization, injection only with no production, and injection–production stoppage. Because the controlling mechanism of CO2 storage in different stages is unknown, the evolution of CO2 storage mechanisms over large timescales is not understood. A mathematical model for the evaluation of CO2 storage, including stratigraphic, residual, solubility, and mineral trapping in low-permeability tight sandstone reservoirs, was established using experimental and theoretical analyses. Based on a detailed geological model of the Huaziping oilfield, calibrated with reservoir permeability and fracture characteristic parameters obtained from well test results, a dynamic simulation of CO2 storage for the entire reservoir life cycle under two scenarios of continuous injection and water–gas alternation were considered. The results show that CO2 storage exhibits the significant stage characteristics of complete storage, dynamic storage, and stable storage. The CO2 storage capacity and storage rate under the continuous gas injection scenario (scenario 1) were 6.34 × 104 t and 61%, while those under the water–gas alternation scenario (scenario 2) were 4.62 × 104 t and 46%. The proportions of storage capacity under scenarios 1 and 2 for structural or stratigraphic, residual, solubility, and mineral trapping were 33.36%, 33.96%, 32.43%, and 0.25%; and 15.09%, 38.65%, 45.77%, and 0.49%, respectively. The evolution of the CO2 storage mechanism showed an overall trend: stratigraphic and residual trapping first increased and then decreased, whereas solubility trapping gradually decreased, and mineral trapping continuously increased. Based on these results, an evolution diagram of the CO2 storage mechanism of low-permeability tight sandstone reservoirs across large timescales was established.

Enhanced Modulation of Streamflow Flash Droughts by Reservoir Operations in India

AbstractStreamflow flash droughts (SFDs) occur due to a rapid decline in streamflow and cause major challenges associated with water availability for downstream ecosystems, hydropower generation, and irrigation water demand. Human interventions such as reservoir operations and reservoir storage can considerably influence streamflow variability. However, the crucial role of dams/reservoirs on the occurrence of SFDs in India remains unexamined. Using a combination of hydrological and hydrodynamical models, we examined the role of reservoirs on SFDs in India during 1971–2020. Reservoirs play a considerable role in the occurrence of SFDs during the summer monsoon season (June‐September) in India. The frequency and severity of SFDs in the presence of reservoirs are substantially lesser than in the absence of them. In addition, high and low antecedent reservoir storage conditions before meteorological flash droughts (MFDs) do not support the rapid decline of streamflow (i.e., SFDs) downstream of reservoirs, while the medium reservoir storage conditions prior to MFDs favor the development of SFDs. Similar to conventional (or long‐term) streamflow droughts (SDs), SFDs are more frequent in the El Nino phase than in the La Nina phase. Unlike the long‐term streamflow droughts, the implementation of dams considerably reduces the frequency of SFDs during both the negative and positive phases of El Nino Southern Oscillation. Overall, our findings demonstrate the considerable role of human interventions in flash drought occurrence, as SFDs are triggered by MFDs but modulated by reservoir storage and operations.

The impact of porous structure on oil–water two-phase flow under CO2 environment in continental shale reservoirs

CO2 applications for enhanced oil recovery and storage in continental shale reservoirs are promising, and there is a need to evaluate the impact of porous structure on oil–water two-phase flow under CO2 environment. In this study, first, digital cores of quartz-rich, carbonate-rich, and clay-rich shales are established using Focused Ion Beam Scanning Electron Microscopy scanning data processed through generative adversarial networks. Subsequently, the pore networks generated by digital cores are quantitatively analyzed using the generalized extreme value distribution. Finally, pore network modeling is carried out to elucidate the effect of porous structural differences on oil–water flow considering CO2 dissolution and capillary forces. The results show that quartz-rich shale, characterized by nanopore intergranular dominance and the highest pore network connectivity, demonstrates the highest relative permeability of the oil phase. Carbonate-rich shale exhibits intermediate relative permeability of oil phase, while clay-rich shale exhibits the worst. The dissolution of CO2 reduces oil–water interfacial tension and oil viscosity, enhances oil mobilization within nanopores, and notably increases the relative permeability of the oil phase. The permeability of the oil phase is governed by pore structure, displaying positive correlations with core heterogeneity, pore radius, coordination number, and throat length, and negative correlations with throat radius.

Paradigm for Determining the Optimal Ultradeep and Super‐thick Saline Aquifer for High‐TDS Mine Water Geological Storage

AbstractSaline aquifers are the most popular waste and CO2 injection and storage reservoirs worldwide. This project proposes that several optimal injection positions should be investigated as hydraulic pressure‐focused positions, in order to relieve the high demands of pump performance. The comprehensive indices (Fi) representing the injectivity of different burial depths were obtained by using information entropy, based on the mercury injection experimental data of 13 rock samples. The results demonstrated that the burial depths of No. 4, No. 1 and No. 2 in the Liujiagou Formation were the most suitable positions for hydraulic focused injection, which means the upper 30 m thickness could be regarded as the hydraulic focused range in the saline aquifer with an average thickness of 400 m. In addition, some laboratory experiments and in situ tests were carried out for the purpose of certifying and analyzing results, including SEM, XRD, brittleness index and logging. The results suggested that the rock samples at the No. 4, No. 1 and No. 2 burial depth ranges have loose microstructure, weak cementation, as well as dual pores and fractures. The lithology is mainly quartz and feldspar, but the clay mineral content is high (10%–25%), which is positive for dissolution. The lithology is suitable for hydraulic fracturing to form extended cracks and micro‐fissures during high‐TDS (total dissolved solids) mine water injection, because of the high brittleness index. Finally, a theoretical and technical framework for high‐TDS mine water injection was established, based on operating pilot engineering. Some theoretical defects and drawbacks learned from the field practices were summarized and solutions proposed. The research in this study could provide guidance and a paradigm for the inexpensive treatment of high‐TDS mine water by injection and storage.

Evaluation of treated wastewater quality from Cap-falcon plant for agriculture irrigation

Wastewater reuse is a useful tool for minimizing the amount of wastewater discharged into the environment. However, it is associated with threats to the environment and public health; consequently, effluent quality assessment is essential prior to reuse. The aim of this study is to assess the physicochemical and microbiological quality of treated wastewater from Cap Falcon wastewater treatment plant for reuse in irrigation. The suitability of treated wastewater from Cap Falcon plant for irrigation was assessed based on its composition and Algerian irrigation water quality standards. The average biochemical oxygen demand (BOD5) and chemical oxygen demand (COD) values decrease from 316 mg/L to 21 mg/L with a mean removal efficiency of 93.0% and from 659 to 40 mg/L with removal efficiency of 93.7% respectively. For total suspended solids (TSS), the concentration at the inlet of the treatment plant is very high but reduces greatly after biological treatment with a removal efficiency over 94.5%. The physico-chemical analyses of treated wastewater samples from the storage reservoir indicated that pH varied from 6.81 to 8.20 with an average value of 7.43, which is slightly alkaline in nature. Electrical conductivity is one of the criteria used to evaluate the suitability of water for agricultural use; the average value was found less than 1500 μS/cm, indicating that the treated wastewater is considered as suitable for irrigation use. On the other hand, microbiological analyses indicate that faecal coliforms are high compared with Algerian water quality reuse standards. Furthermore, the overall quality of tertiary treated wastewater was analyzed by calculating the water quality index. The calculated index for the physicochemical and microbiological parameters was 96, which corresponds to a water quality type “very poor” signifying that this effluent can only be used for restricted irrigation practices.

Polluted water from a storage dam (Villa Victoria, méxico) induces oxidative damage, AChE activity, embryotoxicity, and behavioral changes in Cyprinus carpio larvae

The Villa Victoria dam is one of the most important storage reservoirs in Mexico since it distributes water to more than 20 million inhabitants in the Metropolitan Zone of Mexico City. In this dam, the common carp (Cyprinus carpio) is an important food resource for the inhabitants, so the aim of this work was to evaluate the oxidative damage (lipoperoxidation, oxidized proteins, antioxidant enzymes activity and gene expression), AChE, embryotoxicity and behavioral changes in C. carpio embryos and larvae exposed to water from Villa Victoria dam for 24, 48, 72 and 96 h. The embryotoxicity was evaluated trough the General Morphology Score (GMS) and the teratogenic index. Behavioral changes in basal locomotor activity and thigmotaxis were evaluated in a DanioVision, Noldus ™. An increase in lipid and protein oxidation as well as modification of CAT, SOD and GPx enzymatic activity was observed during the exposure times. The GMS indicated a low development in the embryos, the teratogenic index was less than 1, however teratogenic effects as yolk edema, fin malformation, head malformation and scoliosis were observed. In parallel, an increase in AChE activity and gene expression was observed reflecting changes in distance traveled of the basal locomotor activity and thigmotaxis at the sampling points. In conclusion, pollutants in water from Villa Victoria dam caused oxidative damage, changes in SOD, CAT, GPx and AChE activity as well as embryotoxicity and modifications in the behavior of C. carpio larvae. This study demonstrates the need to implement restoration programs for this reservoir since, contamination in the Villa Victoria dam could eventually endanger aquatic life and human health.

Prospectivity analysis for underground hydrogen storage, Taranaki basin, Aotearoa New Zealand: A multi-criteria decision-making approach

Seasonal underground hydrogen storage (UHS) in porous media provides an as yet untested method for storing surplus renewable energy and balancing our energy demands. This study investigates the technical suitability for UHS in depleted hydrocarbon fields and one deep aquifer site in Taranaki Basin, Aotearoa New Zealand. Prospective sites are assessed using a decision tree approach, providing a “fast-track” method for identifying potential sites, and a decision matrix approach for ranking optimal sites. Based on expert elicitation, the most important factors to consider are storage capacity, reservoir depth, and parameters that affect hydrogen injectivity/withdrawal and containment. Results from both approaches suggest that Paleogene reservoirs from gas (or gas cap) fields provide the best option for demonstrating UHS in Aotearoa New Zealand, and that the country’s projected 2050 hydrogen storage demand could be exceeded by developing one or two high ranking sites. Lower priority is assigned to heterolithic and typically finer grained, labile and, clay-rich Miocene oil reservoirs, and to deep aquifers that have no proven hydrocarbon containment.

Geological survey techniques and carbon storage: Optimizing renewable energy site selection and carbon sequestration

Geological survey techniques play a crucial role in optimizing site selection for renewable energy projects and identifying suitable locations for carbon storage to mitigate climate change. This abstract provides an overview of how geological survey techniques can be used to achieve these objectives. Renewable energy development, particularly solar and wind power, requires careful site selection to maximize energy generation efficiency and minimize environmental impacts. Geological surveys are instrumental in assessing factors such as subsurface geology, topography, soil composition, and hydrological conditions. These surveys help identify suitable locations with optimal wind or solar resources and geologic conditions for infrastructure development. Additionally, geological surveys are essential for identifying suitable sites for carbon storage, a critical component of carbon capture and storage (CCS) technologies aimed at reducing greenhouse gas emissions. Geological formations, such as deep saline aquifers, depleted oil and gas reservoirs, and unmineable coal seams, can serve as storage reservoirs for captured carbon dioxide (CO2). Geological surveys help characterize these formations to assess their suitability for long-term CO2 storage, considering factors such as porosity, permeability, and sealing integrity. Optimizing site selection for renewable energy projects and carbon storage requires a comprehensive understanding of subsurface geology and environmental conditions. Advanced geological survey techniques, such as seismic imaging, remote sensing, and geophysical surveys, are essential for acquiring detailed subsurface data. These techniques enable scientists and engineers to assess site suitability, evaluate risks, and design effective mitigation measures. In conclusion, geological survey techniques are invaluable tools for optimizing site selection for renewable energy projects and identifying suitable locations for carbon storage. By leveraging these techniques, stakeholders can make informed decisions that promote sustainable energy development and mitigate the impacts of climate change.