Storage Devices Research Articles

Covalent surface grafting of Ti3C2Tx flakes for enhancement of symmetric supercapacitor performance

In this work the covalent surface modification of MXene flakes (Ti3C2Tx) was proposed for the increasing of the performance of subsequently created symmetric supercapacitor. Covalent surface modification was performed with utilization of diazonium salts (hydrophobic or hydrophilic) and plasmon-assisted photochemistry. Applied procedure allows to block the reactive (weak and/or catalytically active) sites on flakes surface and increase the flakes interplanar spacing, both enhancing the functionality of an MXene-based supercapacitor. Especially pronounced positive effect gives the surface modification with hydrophilic chemical moieties. In particular, we observed increase of supercapacitance from 197 to 284 F g−1 in acidic and from 86 to 142 F g−1 in alkaline conditions for flakes grafted with –C6H4–COOH chemical moieties at scan rate 20 mV/s. The flakes grafted with hydrophobic chemical moieties allow to achieve almost constant value of supercapacitance for different speed of charge discharge. In addition, the surface grafting prevents the supercapacitor degradation and decelerates the spontaneous discharge in open circuit mode. These results suggest strategy for further improvement of MXene-based supercapacitors as energy storage device.

Boil-Off Gas Generation in Vacuum-Jacketed Valve Used in Liquid Hydrogen Storage Tank

The boiling point of liquid hydrogen is very low, at −253 °C under atmospheric pressure, which causes boil-off gas (BOG) to occur during storage and transport due to heat penetration. Because the BOG must be removed through processes such as re-liquefaction, venting to the atmosphere, or incineration, related studies are required to estimate the heat transfer of storage and transport devices and to improve insulation to reduce BOG generation. In this study, a vaporization analysis was performed on a vacuum-jacketed valve used in liquid hydrogen storage and transport devices to calculate the amount of BOG generation considering the flow characteristics at the vena contracta and the saturation temperature. At a pressure of 1 bar in the liquid hydrogen storage tank, the maximum fluid flow velocity and minimum static pressure occurred at the vena contracta, with values of 62.9 m/s and −0.4 bar, respectively, and the BOG generation rate was estimated as 0.132 m3/h, where the saturation temperature was minimized at 19.3 K. Furthermore, through case studies, when the pressure in the liquid hydrogen storage tank increased to 1.5 and 2 bar, the static pressure and saturation temperature decreased, and the BOG generation rate increased to 0.221 and 0.283 m3/h, respectively.

Fluorophilic Sigma(σ)‐Lock Self‐Healable Copolymers

Although F‐containing molecules and macromolecules are often used in molecular biology to increase the binding with Lewis acidic groups by introducing favorable C‐F dipoles, there is virtually no experimental evidence and limited understanding of the nature of these interactions, especially their role in synthetic polymeric materials. These studies elucidate the molecular origin of inter‐ and intra‐chain interactions responsible for self‐healing of F‐containing copolymers composed of pentafluorostyrene and n‐butyl acrylate units (p(PFS/nBA). Guided by dynamic surface oscillating force (SOF) and spectroscopic measurements supported by molecular dynamics (MD) simulations, these studies show that the reformation of σ‐σ orbitals in ‐C‐F of PFS and CH3CH2‐ of nBA units enables the recovery of entropic energy via flouorophilic‐σ‐lock van der Waals forces when PFS/nBA molar ratios are ~50/50. The strength of these interactions determined experimentally for self‐healable PFS/nBA compositions is in the order ~0.3 kcal/mol which primarily comes from flouorophilic‐σ‐lock (~70%) contributions. These interactions are significantly diminished for non‐self‐healable counterparts. Strongly polarized ‐C‐F σ orbitals create lateral dipolar forces enhancing the affinity towards ‐C‐H orbitals, facilitating energetically favorable interactions. Entropic recovery driven by non‐covalent bonding offers a valuable tool in designing materials with unique functionalities, particularly self‐healable batteries or other energy storage devices.

Agar‐Based Interface for Suppressing Parasitic Reactions toward High‐Performance Aqueous Zn‐Ion Batteries

AbstractWith advantages including high capacity, intrinsic safety and low cost, aqueous zinc‐ion batteries (AZIBs) are ideal electrochemical energy storage devices for large‐scale and portable energy storage. However, the development of AZIBs suffers from tricky challenges, such as the notorious Zn dendrite growth and severe parasitic reactions. Herein, as a low‐cost and nontoxic biomass, agar is adopted to construct an interface layer on Zn foil to mitigate side reactions and induce uniform Zn deposition on Zn anodes. The interaction between Zn2+ and polar functional groups of agar can regulate Zn2+ distribution and promote Zn2+ desolvation, thus simultaneously achieving homogenous Zn deposition and suppressed hydrogen evolution reaction. Meanwhile, SO42− anions are blocked from contacting Zn surface due to electrostatic repulsion, greatly restraining corrosion and passivation. Consequently, Zn||A‐Cu asymmetric cell operates normally for 590 cycles with an average coulombic efficiency of 99.5 %, suggesting good reversibility of Zn plating/stripping. Notably, A‐Zn symmetric cell exhibits a long lifespan of 1100 h at 2 mA cm−2. Furthermore, the A‐Zn||NVO full cell displays a superb capacity retention of 94.8 % after 3600 cycles at 5 A g−1. This work offers a novel interface modification method for constructing stable and dendrite‐free anodes of AZIBs.

Fluorophilic Sigma(σ)-Lock Self-Healable Copolymers.

Although F-containing molecules and macromolecules are often used in molecular biology to increase the binding with Lewis acidic groups by introducing favorable C-F dipoles, there is virtually no experimental evidence and limited understanding of the nature of these interactions, especially their role in synthetic polymeric materials. These studies elucidate the molecular origin of inter- and intra-chain interactions responsible for self-healing of F-containing copolymers composed of pentafluorostyrene and n-butyl acrylate units (p(PFS/nBA). Guided by dynamic surface oscillating force (SOF) and spectroscopic measurements supported by molecular dynamics (MD) simulations, these studies show that the reformation ofσ-σorbitals in -C-F of PFS and CH3CH2- of nBA units enables the recovery of entropic energy viaflouorophilic-σ-lockvan der Waals forces when PFS/nBA molar ratios are ~50/50. The strength of these interactions determined experimentally for self-healable PFS/nBA compositions is in the order ~0.3 kcal/mol which primarily comes fromflouorophilic-σ-lock(~70%) contributions. These interactions are significantly diminished for non-self-healable counterparts. Strongly polarized -C-Fσorbitals create lateral dipolar forces enhancing the affinity towards -C-H orbitals, facilitating energetically favorable interactions. Entropic recovery driven by non-covalent bonding offers a valuable tool in designing materials with unique functionalities, particularly self-healable batteries or otherenergy storage devices.

The Preisach model of hysteresis: fundamentals and applications

Abstract The Preisach model is a well-known model of hysteresis in the modern nonlinear science. This paper provides an overview of works that are focusing on the study of dynamical systems from various areas (physics, economics, biology), where the Preisach model plays a key role in the formalization of hysteresis dependencies. Here we describe the input-output relations of the classical Preisach operator, its basic properties, methods of constructing the output using the demagnetization function formalism, a generalization of the classical Preisach operator for the case of vector input-output relations. Various generalizations of the model are described here in relation to systems containing ferromagnetic and ferroelectric materials. The main attention we pay to experimental works, where the Preisach model has been used for analytic description of the experimentally observed results. Also, we describe a wide range of the technical applications of the Preisach model in such fields as energy storage devices, systems under piezoelectric effect, models of systems with long-term memory. The properties of the Preisach operator in terms of reaction to stochastic external impacts are described and a generalization of the model for the case of the stochastic threshold numbers of its elementary components is given.

Asymmetric Coordination of Bimetallic Fe-Co Single-Atom Pairs toward Enhanced Bifunctional Activity for Rechargeable Zinc-Air Batteries.

The advancement of rechargeable zinc-air batteries (RZABs) faces challenges from the pronounced polarization and sluggish kinetics of oxygen reduction and evolution reactions (ORR and OER). Single-atom catalysts offer an effective solution, yet their insufficient or singular catalytic activity hinders their development. In this work, a dual single-atom catalyst, FeCo-SAs, was fabricated, featuring atomically dispersed N3-Fe-Co-N4 sites on N-doped graphene nanosheets for bifunctional activity. Introducing Co into Fe single-atoms and secondary pyrolysis altered Fe coordination with N, creating an asymmetric environment that promoted charge transfer and increased the density of states near the Fermi level. This catalyst achieved a narrow potential gap of 0.616 V, with a half-wave potential of 0.884 V for ORR (vs the reversible hydrogen electrode) and a low OER overpotential of 270 mV at 10 mA cm-2. Owing to the superior activity of FeCo-SAs, RZABs exhibited a peak power density of 203.36 mW cm-2 and an extended cycle life of over 550 h, exceeding the commercial Pt/C + IrO2 catalyst. Furthermore, flexible RZABs with FeCo-SAs demonstrated the promising future of bimetallic pairs in wearable energy storage devices.

Efficiency Analysis of Hybrid Extreme Regenerative with Supercapacitor Battery and Harvesting Vibration Absorber System for Electric Vehicles Driven by Permanent Magnet Synchronous Motor 30 kW

This research presents an approach to the hybrid energy harvesting paradigm (HEHP) based on suspended energy harvest. It uses a harvesting vibration absorber (HVA) with an SC/NMC-lithium battery hybrid energy storage paradigm (SCB-HESP) equipped regenerative braking system (SCB-HESP-RBS) for electric vehicles 2 tons in gross weight (MEVs) driven by a 30 kW permanent magnet synchronous motor (PMSM). During regenerative braking, the ANN mechanism controls the RBS to adjust the switching waveform of the three-phase power inverter, and the braking energy transfers to the energy storage device. Additionally, a supercapacitor (SC) equipped with HVA can absorb energy from vehicle vibrations and convert it into electrical energy. The energy-harvesting efficiency of MEV based on SCB-HESP-RBS using HVA suspended energy harvesting enhances the efficiency maximum to 50.58% and 15.36% in comparison to MEV with only-HVA and SCB-HESP-RBS, respectively. Further, the MEV with SCB-HESP-RBS using HVA has a driving distance of up to 247.34 km (22.5 cycles) when compared with SCB-HESP-RBS (214.40 km, 19.5 cycles) and only-HVA (164.25 km, 15 cycles).

Carbon-Based Composites for Oxygen Evolution Reaction Electrocatalysts: Design, Fabrication, and Application

The four-electron oxidation process of the oxygen evolution reaction (OER) highly influences the performance of many green energy storage and conversion devices due to its sluggish kinetics. The fabrication of cost-effective OER electrocatalysts via a facile and green method is, hence, highly desirable. This review summarizes and discusses the recent progress in creating carbon-based materials for alkaline OER. The contents mainly focus on the design, fabrication, and application of carbon-based materials for alkaline OER, including metal-free carbon materials, carbon-based supported composites, and carbon-based material core–shell hybrids. The work presents references and suggestions for the rational design of highly efficient carbon-based OER materials.

Metal-Organic Framework for Aluminum based Energy Storage Devices: Utilizing Redox Additives for Significant Performance Enhancement.

There are various methods being tried to address the sluggish kinetics observed in Al-ion batteries (AIBs). They mostly deal with morphology tuning, but have led to limited improvement. A new approach is proposed to overcome this limitation. It focuses on the use of a redox additive modified electrolyte in combination with framework like materials, which have wider channels. The ordered microporous and interconnected framework of ZIF 67, with large surface area, effectively facilitates the diffusion of aluminum ions. Therefore, AIBs are able to exhibit a superior discharge capacity of 288 mAh g-1 at 0.2 A g-1 current density with robust cycling stability. The addition of potassium ferricyanide as a redox-active species in an aqueous solution of aluminum chloride (supporting electrolyte) leads to significant enhancement in the specific capacity with much higher cycling stability. Al-ion based BatCap devices can be assembled by using ZIF 67 as the cathode, ZIF 67 derived porous carbon as the anode, and a redox additive modified electrolyte. The BatCap device exhibits excellent energy density of 86 Wh kg-1 at a power density of 2 KW kg-1, which is higher than reported aqueous AIBs. The ex situ characterization clearly explains the unexplored mechanism of redox additives in AIBs.

Nickel-copper-cobalt mixed oxide electrode material for high performance asymmetric supercapacitor

Nickel copper cobalt oxide (NiCuCoO) ternary metal oxide nanoparticles were synthesized by employing the hydrothermal method. NiCuCoO electrode demonstrates a specified capacity of 596 C g−1 at 1 A g−1, high capacitance retaining of 99% even if 1000 sequences at the density of current 10 A g−1, and significant extended cyclic strength over 1000 sequences. The gathered asymmetric supercapacitor (ASC) tool via NiCuCoO as the cathode and activated carbon as anode materials achieve a specified capacity of 168 C g−1 at a current density of 1 Ag−1, an excellent capacity retaining of 95% even later than 5000 sequences at a density of current 10 A g−1. The fabricated device exhibits a high density of energy and power is 96 Wh kg−1 and 841 W kg−1. The prepared material confirms an excellent capacitance routine, so this work represents for a next-generation energy storage device.

Organosulfur Cathodes in Lithium Metal Batteries: Bridging the Gap between Fundamentals and Practical Applications

AbstractHigh‐specific energy sulfur‐based cathodes have attracted considerable interest in lithium batteries. Organosulfur cathodes offer inherent advantages of high element abundance and an extended cycling life, aligning with the evolving requirements of future energy storage devices. Over the past decade, research efforts have been devoted to optimizing electrochemical performance through the rich and tunable molecular structures of organosulfur compounds. To further advance the fundamental research and practical application of lithium‐organosulfur batteries, a systematical analysis of the correlation between the molecular structures and electrochemical mechanisms of organosulfur cathodes is imperative. This involves deriving the key parameters at the cell level and investigating the feasibility. In this review, the thermodynamics, reaction processes, and electrochemical kinetics of organosulfur cathodes, grounded in fundamental theories of electrochemistry and materials science are discussed. Expanding the insights, comparisons among elemental sulfur, organosulfur, and n‐type organic cathodes (e.g., carbonyl cathodes) are drawn. The gap between fundamentals and practical applications targeting 500 Wh kg−1 lithium organosulfur batteries is highlighted through energy density calculations and identification of key factors affecting pouch cells. Finally, potential strategies and prospects for the overall design of advanced lithium‐organosulfur batteries are proposed, considering both theoretical foundations and practical implementations.

Vitrification-enabled enhancement of proton conductivity in hydrogen-bonded organic frameworks

Hydrogen-bonded organic frameworks (HOFs) are versatile materials with potential applications in proton conduction. Traditional approaches involve incorporating humidity control to address grain boundary challenges for proton conduction. This study finds vitrification as an alternative strategy to eliminate grain boundary effect in HOFs by rapidly melt quenching the kinetically stable HOF-SXU-8 to glassy state HOF-g. Notably, a remarkable enhancement in proton conductivity without humidity was achieved after vitrification, from 1.31 × 10−7 S cm−1 to 5.62× 10−2 S cm−1 at 100 °C. Long term stability test showed negligible performance degradation, and even at 30 °C, the proton conductivity remained at high level of 1.2 × 10−2 S cm−1. Molecule dynamics (MD) simulations and X-ray total scattering experiments reveal the HOF-g system is consisted of three kinds of clusters, i.e., 1,5-Naphthalenedisulfonic acid (1,5-NSA) anion clusters, N,N-dimethylformamide (DMF) molecule clusters, and H+-H2O clusters. In which, the H+ plays an important role to bridge these clusters and the high conductivity is mainly related to the H+ on H3O+. These findings provide valuable insights for optimizing HOFs, enabling efficient proton conduction, and advancing energy conversion and storage devices.

High-pressure intrusion of double salt aqueous solution in pure silica chabazite: searching for cation selectivity

Heterogeneous lyophobic systems (HLSs), i.e. systems composed of a nanoporous solid and a non-wetting liquid, have attracted much attention as promising candidates for innovative mechanical energy storage and dissipation devices. In this work, a new HLS based on a pure silica chabazite (Si-CHA) and a ternary electrolyte solution (KCl + CaCl2) is studied from porosimetric and crystallographic points of view. The combined approach of this study has been fundamental in unravelling the properties of the system. The porosimetric experiments allowed the determination of the energetic behaviour, while high-pressure in situ crystallographic analyses helped elucidate the mechanism of intrusion. The results are compared with those obtained for systems involving the same zeolite but intruded with solutions containing only single salts (CaCl2 or KCl). The porosimetric results of the three Si-CHA systems intruded by simple and complex electrolyte solutions (KCl 2 M, CaCl2 2 M and the mixture KCl 1 M + CaCl2 1 M) suggest that the intrusion pressure is mainly influenced by the nature of the cations. The CaCl2 2 M solution shows the highest intrusion pressure and KCl 2 M the lowest, whereas the mixture KCl 1 M + CaCl2 1 M is almost in the middle. These differences are probably related to the higher hydration enthalpy and Gibbs energy of Ca2+ compared with those of K+. It has been demonstrated that partial ion desolvation is needed to promote the penetration of the species, and a higher solvation energy requires higher pressure. The `intermediate' value of intrusion pressure shown by the complex electrolyte solution arises from the fact that, statistically, the second/third solvation cation shells can be assumed to be partially shared between K+ and Ca2+. The stronger interaction of Ca2+ with H2O molecules thus also influences the desolvation of K+, increasing the pressure needed to activate the process compared with the pure KCl 2 M solution. This is confirmed by the structural investigation, which shows that at the beginning of intrusion only K+, Cl− and H2O penetrate the pores, whereas the intrusion of Ca2+ requires higher pressure, in agreement with the hydration enthalpies of the two cations.

Centrifugal-Gravity-Enforced Deposition of MXene Electrodes for High-Performance and Ultrastable Microsupercapacitors.

Two-dimensional (2D) transition metal carbides, known as MXenes, have captured much attention for their excellent electrical conductivity and electrochemical capability. However, the susceptibility of MXenes to oxidation, particularly Ti3C2Tx transforming into titanium dioxide upon exposure to ambient air, hinders their utilization for extended operational life cycles. This work introduces a simple and straightforward method for producing ultrathin MXene electrode films tailored for energy storage applications, employing centrifugal-gravity force. Our approach significantly suppresses the oxidation phenomenon that arises in MXene materials and also effectively prevents the recrystallization of potentially residual LiF during the film formation. Additionally, the utilization of this MXene electrode in an all-solid-state microsupercapacitor (MSC) with an interdigitated pattern demonstrates an exceptionally improved and stable electrochemical performance. This includes a high volumetric capacitance of approximately 467 F cm-3, an energy density of around 65 mWh cm-3, and impressive long-term cycle stability, retaining about 94% capacity after 10 000 cycles. Moreover, a downsized MSC device exhibits remarkable mechanical durability, retaining over 98% capacity even when folded and sustaining stability over extended periods. Therefore, we believe that this study provides valuable insights for advancing highly integrated energy storage devices, ensuring exceptional electrochemical efficiency and prolonged functionality in diverse environments, whether ambient or humid.

Photo-Stimulated Zn-based Batteries: Progress, Challenges, and Perspectives.

Solar energy, as a renewable energy source, dominates the vast majority of human energy, which can be harvested and converted by photovoltaic solar cells. However, the intermittent availability of solar energy restricts the actual utilization circumstances of solar cells. Integrating photo-responsive electrodes into an energy storage device emerges as a dependable and executable strategy, fostering the creation of photo-stimulated batteries that seamlessly amalgamate the process of solar energy collection, conversion, and storage in one system. Endowed by virtues such as cost-effectiveness, facile manufacturing, safety, and environmental friendliness, photo-stimulated Zn-based batteries have attracted considerable attention. The progress report furnishes a brief overview, summarizing various photo-stimulated Zn-based batteries. Their configurations, operational principles, advancements, and the intricate engineering of photoelectrode designs are introduced, respectively. Through rigorous architectural design, photo-stimulated Zn-based batteries exhibit the ability to initiate charging by saving electricity usage, and in certain instances, even without the need for external electrical grids under illumination. Furthermore, the compensation of solar energy can be explored to improve the output electric energy. At last, opportunities and challenges toward photo-stimulated Zn-based batteries in the process of development are proposed and discussed in the hope of expanding their application scenarios and accelerating the commercialization progress.

Boosting Supercapacitor Efficiency with Amorphous Biomass-Derived C@TiO2 Composites.

Carbon materials are readily available and are essential in energy storage. One of the routes used to enhance their surface area and activity is the decoration of carbons with semiconductors, such as amorphous TiO2, for application in energy storage devices. This work reports the preparation of amorphous TiO2 nanopowders, which were obtained through the anodization of titanium in ethaline media. The obtained amorphous TiO2 was used to obtain TiO2-decorated carbon (obtained through the carbonization of glycogen precursor from mussel cooking wastewater, under N2 atmosphere) composites through three different methods: electrochemical in-situ attachment of TiO2 nanopowders to the carbon matrix using ultrasounds and sonication in ethaline. Commercial TiO2 was used as the comparison material. Morphology, composition, and structure analysis were performed, followed by the electrochemical analysis in ethaline electrolyte. The in-situ attachment of amorphous TiO2 to the carbon matrix shows the most promising electrochemical performance of 956 F g-1 at 1 A g-1 for the three-electrode cell setup, with 100% and 98% capacitance retention after 1000 and 10000 cycles. On a two-electrode symmetric solid-state electrolyte cell, the gravimetric capacitance is 1251 F g-1, at 1 A g-1, with 90% and 78% capacitance retention after 1000 and 10000 cycles, respectively.

Recyclable organic radical electrodes for metal-free batteries.

Organic batteries are one of the possible routes for transitioning to sustainable energy storage solutions. However, the recycling of organic batteries, which is a key step toward achieving circularity, is not easily achieved. This work shows the direct recycling of poly(2,2,6,6-tetramethylpiperidinyloxy-4-yl) (PTMA) and poly(2,2,6,6-tetramethylpiperidinyloxy-4-yl acrylamide) (PTAm) based composite electrodes. After charge-discharge cycling, the electrodes are deconstructed using a solubilizing-solvent and then reconstructed using a casting-solvent. The electrochemical properties of the original and recycled electrodes are compared using cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD) cycling, from which it is discovered using time-of-flight secondary ion mass spectrometry (ToF-SIMS) that recycling can be challenged by the formation of a solid-electrolyte interphase (SEI). In turn, an additive is proposed to modify the SEI layer and improve the properties after recycling. Last, an anionic rocking chair battery consisting of PTAm electrodes as both positive and negative electrodes is demonstrated, in which the electrodes are recycled to form new battery. This work gives demonstrates the recycling of composite electrodes for organic batteries and provides insights into the challenges and possible solutions for recycling the next-generation electrochemical energy storage devices.

Design Strategies for Anti‐Freeze Electrolytes in Aqueous Energy Storage Devices at Low Temperatures

AbstractWith the continuous development of electrochemical energy storage technology, especially in the current pursuit of environmental sustainability and safety, aqueous energy storage devices, due to their high safety, environmental friendliness, and cost‐effectiveness, are becoming an important direction of development in the field of energy storage. Diverse application scenarios require that energy storage systems be capable of continuous power supply under low temperature conditions. However, conventional aqueous electrolytes freeze at extremely low temperatures, causing limited ion transport and slow reaction kinetics, degrading the performance of the energy storage system. The design of low‐temperature anti‐freeze aqueous electrolytes has become an effective way to address this issue. In this review, the deep connection between hydrogen bonds (HBs) interactions in aqueous electrolytes and the liquid‐to‐solid conversion process, and the fundamental principles of the anti‐freeze mechanism is first explored. Subsequently, a systematic categorization and discussion of the design strategies for low‐temperature anti‐freeze aqueous electrolytes are conducted. Finally, potential directions are proposed. This review aims to provide comprehensive scientific guidance and technical reference for the development of anti‐freeze aqueous electrolytes with excellent low‐temperature performance, thereby promoting the application and innovation of aqueous energy storage devices in low‐temperature environments.

Stable Photo-Rechargeable Al Battery for Enhancing Energy Utilization.

The photovoltaic cells (PVs) are able to convert solar energy to electric energy, while energy storage devices are required to be equipped due to the fluctuations of sunlight. However, the electrical connection of PVs and energy storage devices leads to increased energy consumption, and thus energy storage ability and utilization efficiency are decreased. One of the solutions is to explore an integrated photoelectrochemical energy conversion-storage device. Up to date, the integrated photo-rechargeable Li-ion batteries often suffer from unstable photo-active materials and flammable electrolytes under illumination, with concerns in safety risk and limited lifetime. To address the critical issues, here a novel photo-rechargeable aluminum battery (PRAB) is designed with safe ionic liquid electrolytes and stable polyaniline photo-electrodes. The integrated PRAB presents stable operation with enhanced reversible specific capacity ∼191% under illumination. Meanwhile, a simplified continuum model is established to provide rational guidance for designing electrode structures along with charging/discharging strategy to meet the practical operation conditions. The as-designed PRAB presents energy saving efficiency ∼61.92% upon charging and energy output increment ∼31.25% during discharging under illumination. The strategy of designing and fabricating stable and safe photo-rechargeable non-aqueous Al battery highlights the pathway for substantially promoting the utilization efficiency of solar energy. This article is protected by copyright. All rights reserved.