Water Steam Research Articles

Environmental Impact of Plastic Recycling in Terms of Energy Consumption: A Comparison of Japan’s Mechanical and Chemical Recycling Technologies

In Japan, mechanical plastic recycling has been widely practiced. In recent years, the chemical recycling method has been gaining interest, especially due to its high-quality products similar to virgin materials. Understanding the environmental impact of both methods from the energy consumption standpoint is crucial so that attempts to preserve plastic resources can be based in the most energy-sustainable way. This research aims to determine the environmental impact of mechanical recycling and two types of chemical recycling technologies (coke oven and gasification) by analyzing their energy usage and environmental loads. The results relating to the electricity consumption and water usage show that mechanical recycling results in a 17% share of global warming potential (GWP), coke oven 51%, and gasification 32%. Although mechanical recycling results in a lower GWP, chemical recycling yields highly valuable products and byproducts that can be reused in its processes, such as steam and industrial water, reducing the overall environmental load. These recovered materials are also potentially useful for other industrial processes in an industrial symbiosis ecosystem.

Effect of temperature and medium environment on corrosion fatigue behavior of Inconel 625

AbstractInconel 625 is a nickel‐based alloy with exceptional creep and corrosion resistance properties. It has emerged as a candidate material for operational and structural use in critical and supercritical power generation plants. Supercritical power plants work at high temperatures, pressure and in an erosive environment that makes metallic materials more vulnerable to corrosion fatigue. This study aimed to evaluate the fatigue crack growth rate (FCGR) at elevated temperatures (550–650°C) in a steam and supercritical water environment. All the experiments were performed at a water oxygen level of 8000 ppb. A cyclic stress of 1 Hz frequency and sine waveform was applied for the test. A 0.6 stress ratio was applied with a maximum stress intensity factor of 32 MPa√m. A direct current potential drop method was applied to detect the crack growth rate (CGR). For the given parameters, fractographic analysis validated the role of corrosion‐fatigue interaction as the primary source of variation in the FCGR. Results revealed that the CGR was enhanced with a rise in temperature under all test environments. The influencing mechanism of temperature on CGR was also discussed.

Simulation of jets induced by steam injection through multi-hole sparger using effective heat and momentum models

Direct contact condensation (DCC) of steam in the pressure suppression pool (PSP) is used to control containment pressure in Boiling Water Reactors (BWRs) and Advanced Pressurized Water Reactors (APWRs). The competition between momentum and heat sources induced by steam injection through multi-hole spargers and blowdown pipes determines whether the pool is thermally stratified or mixed. Development of thermal stratification affects capacity of the PSP to condense steam. To enable computationally efficient modeling of the PSP transients, the Effective Heat Source (EHS) and Effective Momentum Source (EMS) models have been proposed previously. The EHS/EMS models enable simulation of the large scale pool behavior without explicit modeling of the steam water interface and DCC phenomena. One of the problems for an optimal implementation of the EHS/EMS models is the definition of the boundary conditions that impose distribution of the momentum and heat sources. In this work, EHS/EMS models are implemented using “Unit Cell” approach in ANSYS Fluent to provide detailed numerical analysis of the individual turbulent jets induced by steam injection through the sparger holes. The model is validated against data from Particle Image Velocimetry (PIV) and temperature measurements for a range of steam injection conditions in the PANDA HP5 tests. Good agreement between the test data and simulations suggests that the proposed model can provide sufficiently accurate prediction of both local and large scale phenomena induced by steam injection into the pool.

Boundary condition coupling methods and its application to BOP-integrated transient simulation of SMART

The load-following operation of small modular reactors (SMRs) requires accurate prediction of transient behaviors that can occur in the balance of plants (BOP) and the nuclear steam supply system (NSSS). However, 1-D thermal-hydraulics analysis codes developed for safety and performance analysis have conventionally excluded the BOP from the simulation by assuming ideal boundary conditions for the main steam and feed water (MS/FW) systems, i.e., an open loop. In this study, we introduced a lumped model of BOP fluid system and coupled it with NSSS without any ideal boundary conditions, i.e., in a closed loop. Various methods for coupling boundary conditions at MS/FW were tested to validate their combination in terms of minimizing numerical instability, which mainly arises from the coupled boundaries. The method exhibiting the best performance was selected and applied to a transient simulation of an integrated NSSS and BOP system of a SMART. For a transient event with core power change of 100–20-100%, the simulation exhibited numerical stability throughout the system without any significant perturbation of thermal-hydraulic parameters. Thus, the introduced boundary-condition coupling method and BOP fluid system model can expectedly be employed for the transient simulation and performance analysis of SMRs requiring daily load-following operations.

Numerical investigation on droplet collision phenomena in moisture separators using population balance model under Lagrangian framework

Droplet collision is an important phenomenon in the industry field. In this work, a new droplet collision model is proposed using moment method coupling with population balance model (PBM) under Lagrangian framework. First, by solving PBM equation with coalescence kernel, the droplet size distribution is obtained. Second, droplets are classified into represented droplets according to the moment parameters. Third, trajectories of represented droplets are simulated by a motion model under the Lagrangian framework. In the results part, three cases (e.g. two-dimensional wave-plate steam water separator, three-dimensional cyclone separator and three-dimensional swirl-vane separator) are performed to verify the accuracy of the new model. A variety of calculation conditions such as inlet velocity varies from 3 m/s to 11 m/s and inlet volume fraction varies from 0.018 % to 0.119 % are set under environment condition of normal temperature and pressure. The pressure distribution, velocity distribution and separation efficiency in the flow field are calculated. The comparison between the calculated results and the experimental values shows that the calculated model has high accuracy. This model shows good potential to describe the droplet collision behavior and the detail information of the particle size distribution for droplet-laden flows.

MoS2 Nanosheets Decorated with Fe3O4 Nanoparticles for Highly Efficient Solar Steam Generation and Water Treatment.

The shortage of water resources has always been one of the most difficult problems that perplexes humanity. Solar steam generation (SSG) has been a new non-polluting and low-cost water purification method in recent years. However, the high cost of traditional photothermal conversion materials and the low efficiency of photothermal conversion has restricted the large-scale application of SSG technology. In this work, composite materials with Fe3O4 nanospheres attached to MoS2 nanosheets were synthesized, which increased the absorbance and specific surface area of the composite materials, reduced the sunlight reflection, and increased the photothermal conversion efficiency. During the experiment, the composite material was evenly coated on cotton. The strong water absorption of cotton ensured that the water could be transported sufficiently to the surface for evaporation. Under one sun irradiation intensity, the evaporation rate of the sample synthesized in this work reached 1.42 kg m-2 h-1; the evaporation efficiency is 89.18%. In addition, the surface temperature of the sample can reach 41.6 °C, which has far exceeded most photothermal conversion materials. Furthermore, the use of this composite material as an SSG device for seawater desalination and sewage purification can remove more than 98% of salt ions in seawater, and the removal rate of heavy metal ions in sewage is close to 100%, with a good seawater desalination capacity and sewage purification capacity. This work provides a new idea for the application of composite materials in the field of seawater desalination and sewage purification.

In Situ Synthesis of ZIF-67 Thin Films Using Low Temperature Chemical Vapor Deposition to Fabricate All-Solid-State Flexible Interdigital in-Planar Microsupercapacitors

This work describes the fabrication of a flexible all-solid-state interdigital in-planar microsupercapacitor (μSC) using the in situ synthesized ZIF-67 thin films as the interdigital finger-electrode materials, platinum (Pt) thin film as the interdigital finger-electrode current collector, laser print technology for the fabrication of interdigital patterns, and low-cost commercial polyethylene terephthalate (PET) sheet as the flexible substrates, assembled with the NaOH/PVA gel electrolyte. ZIF-67 thin films are in situ synthesized onto PET substrate by ultralow temperature (ULT) chemical vapor deposition (CVD) technology at a low temperature of 140°C. We herein report the ULT CVD approach for gas phase synthesizing ZIF-67 thin films, the exactly heating temperature can produce vaporized water steam, sublimated 2-methylimidazole (2-MIM) and cobalt(II) acetylacetonate (Co(acac)2) vapors at the same time. The vaporized and sublimated gaseous precursors demonstrated molecular-level reactions, including the deprotonation of 2-MIM via water steam, and the following coordinated reactions with cobalt ions decomposed from Co(acac)2, for the efficiently straightforward deposition to form the uniform ZIF-67 thin films onto the substrate surface. Herein, the integration of pattern printing, CVD depositing ZIF-67 thin films, and lift-off patterning processes demonstrated a comprehensive achievement and good compatibility to integrate MOFs into miniaturized energy-storage devices.

Experimental Investigations and Numerical Studies of Two-Phase Countercurrent Flow Limitation in a Pressurized Water Reactor: A Review

Gas–liquid two-phase countercurrent flow limitation (CCFL) phenomena widely exist in nuclear power plants. In particular, the gas–liquid countercurrent flow limitation phenomena in a pressurized water reactor (PWR) during a loss-of-coolant accident (LOCA) or a small-break loss-of-coolant accident (SBLOCA) play an important role in nuclear reactor safety research. Over several decades, a series of experimental investigations and numerical studies have been carried out to study the CCFL phenomena in a PWR. For the experimental investigations, numerous experiments have been conducted, and different CCFL mechanisms and CCFL characteristics have been obtained in various test facilities simulating different scenarios in a PWR. The CCFL phenomena are affected by many factors, such as geometrical characteristics, liquid flow rates, and fluid properties. For the numerical studies, more and more numerical models were presented and applied to the calculations of two-phase countercurrent flow over the past several decades. It is considered that the computational fluid dynamics (CFD) tools can simulate most of the two-phase flow configurations encountered in nuclear power plants. In this paper, the experimental investigations and the numerical studies on two-phase countercurrent flow limitation in a PWR are comprehensively reviewed. This review provides a further understanding of CCFL in a PWR and gives directions regarding future studies. It is found that relatively fewer investigations using steam–water under high system pressures are performed due to the limitation of the test facilities and test conditions. There are a number of numerical studies on countercurrent two-phase flow in a PWR hot leg geometry, but the simulations in other flow channels were relatively rare. In addition, almost all of the numerical simulations do not include heat and mass transfer. Thus, it is necessary to investigate the effects of heat and mass transfer experimentally and numerically. Furthermore, it is of significance to perform numerical simulations for countercurrent two-phase flow with a fine computational grid and suitable models to predict the formation of small waves and the details in two-phase flow.

Effects of deodorization on the content of polycyclic aromatic hydrocarbons (PAHs), 3-monochloropropane-1,2-diol esters (3-MCPDE) and glycidyl esters (GE) in rapeseed oil using ethanol steam distillation at low temperature

High temperature is beneficial for the removal of polycyclic aromatic hydrocarbons (PAHs) from oil via steam, but leads to an increase in the content of 3-monochloropropane-1,2-diol esters (3-MCPDE) and glycidyl esters (GE). To inhibit the production of 3-MCPDE and GE during the removal of PAHs, rapeseed oil was deodorized using ethanol steam at low-temperature (140–220 °C) (L-ESD) and the content changes were studied for PAHs, 3-MCPDE and GE, and compared with conventional high-temperature water steam deodorization (H-WSD) (250 °C for 60 min). The removal rates of PAHs in L-ESD oil can be higher than those in conventional H-WSD oil, and the contents of 3-MCPDE and GE in L-ESD oil (140–180 °C for 60–100 min) ranged from 48.32 to 73.65 % and 50.49–69.90 %, respectively, in H-WSD oil due to the lower temperature of ethanol steam deodorization. These results indicate that L-ESD is beneficial in minimizing the contents of PAHs, 3-MCPDE and GE in vegetable oil.

In vitro efficacy of essential oils against Haematobia irritans

The horn fly (Haematobia irritans) infestation in the cattle in Brazil leads to significant economic damage for livestock. The efficacy of many essential oils has been demonstrated in the control of veterinary ectoparasites. This study aimed to evaluate the in vitro efficacy of four essential oils to adult horn fly control. The essential oil from Mesosphaerum suaveolens (L.) Kuntze (Lamiaceae) was extracted by hydro-distillation, while that the water steam distillation method was used to extract the essential oils from Varronia curassavica (Jacq.) Roem. & Schult. (Boraginaceae), Alpinia zerumbet (Pers.) B.L. Burtt & R.M. Sm. (Zingiberaceae) and Psidium guajava L. (Myrtaceae). Afterwards, all the essential oils were analyzed by Gas Chromatography Mass Spectrometry (GC?MS) and Flame Ionization Detector (GC-FID) for determination of their chemical composition. The bioassays in vitro were performed according to the impregnated filter paper methodology. All the essential oils evaluated in this study exhibited efficacy in vitro against H. irritans. The highest mortality of H. irritans was determined by essential oils from A. zerumbet (100%) and M. suaveolens (96.2%) at 50 mg mL-1. In concentration of 100 mg mL-1 V. curassavica and P. guajava essential oils caused the mortality of 99.2% and 82.8%, respectively. The A. zerumbet, M. suaveolens, V. curassavica and P. guajava essential oils showed in vitro efficacy against H. irritans. Further studies with associations and nanoemultions are necessary to increase the efficacy and stability of these essential oils on field conditions.

Benefits of sauna on lung capacity, neurocognitive diseases, and heart health

Sauna refers to passive heat therapy that involves exposure of the body to a high-temperature environment for an appropriately short period, contingent on the therapy’s purpose. Ideally, the therapy aims to raise the internal body temperature by a few degrees, and its effect happens in two phases. The first phase occurs during the first ten minutes, encouraging the body to perspire while maintaining a temperature of around 98.6 degrees. The extra heat is dispersed by increased blood circulation, blood pushing on the skin's surface, and sweating. The body enters the second phase after 10-30 minutes in the sauna. During this period, the body cannot disperse the sauna heat, thereby increasing the body temperature. In return, the heart rate and sweating increase. There are four different types of saunas. These include traditional saunas, usually heated with wood-burning stoves, rocks, or an electric coil. Far-infrared saunas are usually heated by metallic or ceramic elements that produce a small spectrum of light, referred to as far-infrared. Infrared lamp saunas are heated using heat lamps that produce radiant heat. The last type is steam saunas, traditionally heated, but water increases the humidity and air temperatures. During sauna therapy, the heart rate of an individual increase from the standard range up to 120 or 150 beats per minute. Unlike physical activity, sauna therapy does not involve any active function of the skeletal muscles. Even though skeletal muscles are inactive during a sauna session, blood volume is partially redirected to the internal organs' exterior body parts due to decreased venous return. Sauna therapy assists in liberating toxins piled in our tissues, facilitating lymph and blood circulation and strengthening one's immune system. Sauna bathing has mainly been used for purposes of relaxation and pleasure. Today, the activity is increasingly becoming popular as a form of treatment therapy. Several pieces of evidence claim that sauna bathing has numerous health benefits, including hemodynamic regulation processes, reduced risk of vascular diseases, cardiovascular disease, neurocognitive diseases, mortality, pulmonary diseases, stabilized arterial blood pressure, and enhancement of conditions such as flu, headache, and arthritis. However, response to stress from heat can increase muscle blood flow. This report will precisely explore the benefits of sauna bathing on lung capacity and heart health for people with cardiovascular, lung-related or respiratory-related, and neurocognitive diseases.

High-Temperature Steam Oxidation of Accident-Tolerant Cr/Mo-Coated Zr Alloy at 1200–1400 °C

The oxidation resistance under LOCA conditions of bilayer Cr/Mo coating deposited on Zr-1Nb zirconium alloy was investigated in this paper. The bilayer Cr (8 μm)/Mo (3 μm) coatings were deposited by magnetron sputtering. Then, oxidation resistance under high-temperature oxidation at 1200–1400 °C in a water steam was studied. The use of a Mo sublayer resulted in limiting Cr-Zr interdiffusion under high-temperature oxidation. It was shown that the Mo barrier sublayer (~3 μm) can provide the protective behavior of the Cr/Mo-coated Zr at 1330 °C in a water steam for at least 720 s. The weight gain of the bilayer Cr/Mo samples was comparable with the monolayer Cr samples after oxidation at 1400 °C. In addition, the analysis of the Cr/Mo-coated Zr alloy oxidation behavior at 1400 °C was carried out.

Can carbon emission trading pilot policy drive industrial structure low-carbon restructuring: new evidence from China.

Industrial structure low-carbon restructuring is an essential channel to accelerate China's economic growth and fulfilling carbon emission reduction goals. Whether carbon emission trading pilot policy, as an influential carbon reduction instrument, fosters industrial structure low-carbon restructuring is of major significance to green economic development. This paper empirically investigates the shock of the carbon emission trading pilot policy on industrial structure low-carbon restructuring using the differences-in-differences (DID) and synthetic control method (SCM). Statistics reveal that sectors with low carbon productivity, such as electricity, steam, and hot water production and supply, ferrous metal smelting and pressing, etc., and sectors with high carbon productivity, such as electrical equipment and machinery, electronics and telecommunication equipment, etc. The industrial structure did not develop a stable trend of change before the 12th Five-Year Plan, but a stable trend of low-carbon restructuring emerged after such a period. Carbon emission trading pilot policy significantly facilitates industrial structural low-carbon restructuring. Carbon emission trading pilot policy inhibits energy-intensive industries in the industrial sector significantly, which promotes industrial structure low-carbon restructuring. Therefore, policymakers need to develop a nationwide carbon emission trading market that includes more industries to guide production factors to industrial sectors with high carbon productivity for industrial restructuring and dual carbon goals.

Improvement of residual oil recovery from oil palm biomass using high pressure water steam system for biodiesel production

Various applications of oil palm empty fruit bunches (OPEFB) would be hindered by the presence of residual oil. This study aimed to remove and recover the residual oil from OPEFB using an integrated system, high pressure water spray system (HPWSS). The performance of the HPWSS was evaluated at different temperatures and water pressures, and the residual oil collected was recovered through water shaking method and tested for biodiesel application. A maximum of 84.9% of residual oil was removed by HPWSS at 60 °C and 8960 kPa and the highest residual oil recovery of 58.8% was observed at 95 °C, using power shaking 5 and 90% of dilution. The following ranges of deterioration of bleachability index (DOBI), free fatty acid (FFA), and peroxide value (PV) for the residual oil were 1.21 to 2.67, 7.11 to 10.4%, and 4.85 to 7.56, respectively. Biodiesel with different blends of recovered residual oil (5%, 10%, and 15%) showed lower values (9.87, 9.57, and 9.56 Nm) of brake torque as compared with diesel (10.89 Nm). Overall, this study showed the potential of HPWSS to obtain an acceptable quality of residual oil from OPEFB to be used in any value-added product generation.

A dual-mode novel Parabolic Trough Collector for process heating applications in small scale industries—Thermo-hydraulic and performance investigation

Only a few industries worldwide use solar heat for industrial processes, despite the fact that it is a proven and cleaner solution. More over, Small-scale industries need hot water and low-enthalpy steam, but such systems receive scant attention due to the active nature of Parabolic Trough Collectors as well as the use of less efficient flat plate technology in this temperature range. This delineate the opportunity for research focus in efficient passive technologies especially in low temperature range. In this regard a novel dual mode Parabolic Trough Collector based on an Open Natural Circulation Loop (PTC-ONCL) is proposed here. Focus of this work is to assess the proposed system’s suitability for process heating applications requiring hot water/low enthalpy steam, especially in rural areas. Experiments are conducted on an in-house prototype. A novel methodology for correlating actual solar data to the input heat load for the in-house test facility is developed. Five representative solar days are considered for individual tests. Startup, transient, and efficiency parameters are evaluated. Productivity, industrial viability, and environmental impact are also accessed. Throughout the test, the loop maintained a stable flow, where the start-up oscillations, thermal oscillations and type-I instabilities are observed. The system operates at an unprecedented efficiency of 72 ± 4% in hot water mode and 70 ± 5% in Steam generation over a 7 h period. The economic analysis shows an ambitious Levelized Cost of Heat of 2.8 cents/kWh, with a payback period of 3.21 years. Moreover environmental study shows its huge potential in reducing the CO 2 emissions. A dimensionless index is proposed to represent the solar day and is correlated to predict the average water temperature and steam generated with RMSE values of 0.98 °C and 0.125 kg respectively. The solar day index comprehends the total irradiation, wind velocity and the ambient temperature. The proposed PTC-ONCL system is capable of producing an annual average of 8.67 kgday −1 and/or 150 L of hot water at an average temperature of 89.07 °C. The results, and the system’s low cost and near-maintenance-free nature demonstrates its capability in the desired application, both technologically and economically. • A passive Parabolic Trough Collector based on an Open Natural Circulation Loop for process heat at low temperature. • New methodology correlates actual solar data to input for an in-house test facility. • Generates 8.67 kg of steam/ hot water at 89 °C on a yearly average with 65% efficiency. • Levelized Cost of Heat of 2.8 cent/kWh & 3.2 years of payback period found promising. • Dimensionless solar day index includes combines irradiation and ambient condition.

Failure Analysis of Once-Through Steam Generator (OTSG) Tube

Abstract The once-through steam generator (OTSG) produces superheated steam using purified feed water. The plant-specific water quality, steam quality, high temperature, and pressure operations lead to the leakage of the OTSG tubes with economic, safety, and environmental consequences. Tube leakage is one of the most frequent causes of OTSG tube failure. A leaking tube was discovered within the OTSG unit of the 110 MW cogeneration plant. The failed section of the tube was removed from the steam generator. Several metallurgical examinations of this tube segment were performed to identify the failure mode and cause. A portion of the tube was analyzed using optical emission spectroscopy (OES) to determine the alloy composition. The results confirmed that the tubing was fabricated from a material consistent with chemical specifications for ASME Specification SB 407 Inconel Alloy 800 (UNS N08800). Glass bead blasting was used to determine the deposit-weight-density (DWD). The DWD value was a maximum of 5.1 g/ft2. The maximum internal deposit thickness was 0.002 in. No evidence of overheating was observed. Scanning electron microscope-energy-dispersive x-ray analysis (SEM-EDXA) was used to determine the elemental composition of the internal deposits. The results indicated that the internal gray deposits primarily comprised iron, chromium, and nickel compounds. There were also fewer amounts of sodium, silicon, aluminum, potassium, and calcium species. The subject tube failure involved a through-wall crack that occurred as stress corrosion cracking (SCC). Additions of caustic solution used in OTSG water treatment practices potentially induced corrosive substances into the tube.

Explosion Differentiation Using Light Emissions—Nuclear Reactor, Steam, Water Hammer, Hydrogen, Piper Alpha, and Hydro-Volcanic Explosions

Abstract Light emissions during chemical reactions provide insights into various scenarios to better understand explosions and water hammers. For example, hydrogen burning and explosions emit blue light, organic carbon combustion and explosions emit combinations of blue and yellow light, water phase changes emit infrared and less visible white light, and white light explosions ignite when multiple chemical reactions are involved. Since experimental tests to observe infrared light during water hammers have not yet been performed, test data from water boiling tests and volcanoes are compared to larger water hammer and steam explosion incidents. Considering these facts and examining a series of photos and videos from the literature and Internet, determinations are proven with respect to water hammers, steam explosions, Piper Alpha water hammer explosions, and chemical explosions. Such evidence proves that steam explosions are important for water hammer accidents, but chemical explosions explain other explosions that have long been considered to be steam explosions. These other explosions include nuclear power plant explosions, hydro-volcanic explosions, and hydrogen explosions, where some of these explosions are, in fact, related to water hammers. This article is primarily a photographic essay to explain the differences between different types of explosions and water hammers, although combustion and explosion principles are expanded and explained to support this essay.

Numerical investigation on pressure oscillations in steam condensation from injection of subcooled water

Steam-water direct contact condensation phenomenon is commonly found in many industries like chemical process industry, nuclear industry etc. In this work the injection of subcooled water into a steam filled pipe has been studied computationally. As a result of steam-water interaction within the pipe the pressure oscillates, which may cause damage to piping system or equipment. The effects of water inlet velocity, water inlet temperature, steam pressure and degree of steam superheating have been studied on the amplitude of pressure oscillations. The first and second dominant frequencies of pressure oscillations have also been obtained and studied. For most of the cases, the first dominant frequency peak was observed in the range ~ 0-1400 Hz whereas, the second dominant frequency peak was in the range ~ 2500 Hz – 3000 Hz. The first pressure peak was observed near the inlet of subcooled water such that its amplitude was increasing with increasing inlet water velocity but was nearly independent of inlet water temperature. Similarly, degree of steam superheating has no noticeable effects on pressure oscillations. It was observed that at a constant water temperature and water injecting velocity, the location of the pressure peaks was independent during the study. Further, the dominant frequency prediction map has been developed for the steam-water interaction in a pipe. The present study is assumed to be beneficial towards unfolds various important facts regarding steam-water interaction in the relevant industrial applications.

Design and calculation of an environmentally friendly carbon-free hybrid plant based on a microgas turbine and a solid oxide fuel cell

This is an overview of a hybrid power plant design and predesign analysis, including a microgas turbine with heat recovery, a high-temperature fuel cell, and a carbon dioxide capture system. A hybrid installation model is presented, taking into account the compatibility and technological limitations of the main components. The material and heat balance calculation of a hybrid power plant is performed depending on the input parameters under partial load conditions. In order to create a decarbonized highly efficient energy production process and in connection with the need to minimize the negative impact of carbon dioxide on the environment, the article presents the developed technologies for carbon dioxide utilization and a carbon adsorption unit as a hybrid power plant part. The hybrid power plant is a carbon-free mini thermal power plant with integrated electricity, steam, and hot water generation and more than 90% total efficiency.

Study on Calculation of Inlet Steam and Inlet Water Flow of Drain Pump of Low Pressure Heater

In the traditional drainage system of low pressure heater of thermal power unit, the measuring point of drain pump is usually added to directly measure the water and steam flow of low pressure heater of drain pump with instruments. This method is time-consuming and labor-intensive, and the measurement results are affected by many environmental factors. In order to solve this problem, this paper proposes an automatic calculation method based on the principle of heat balance.