Speed Gradient Research Articles

The Analysis of the Intensity and Vibration Time on the Mechanical Properties of Hardened Concrete

In order to achieve optimal physical and mechanical properties of hardened concrete, it is necessary to determine the right intensity and vibration time of fresh concrete during casting. Since concrete is considered as a polydisperse substance and various aggregate grains move randomly during vibration, it is very difficult to describe this stochastic phenomenon using exact physical equations and it is more advantageous to apply an experimental approach to verify the effects of vibration on fresh concrete. The effect of vibrations on fresh concrete increases the speed gradient of individual grains and thus reduces the viscosity of the cement paste. The intensity of vibration is determined mainly by the frequency, amplitude and centrifugal force of the eccentric of the vibrating machine. The optimal vibration time is generally considered to be the "minimum required". Insufficient vibration caused by an unsuitable vibrating machine or a short vibration time can result in insufficient compaction of the aggregate grains, non-release of accumulated air from the fresh concrete mixture, formation of cavities or poor-quality casting of parts of the structure with a higher degree of reinforcement. Vibration with excessive intensity or time can also be considered dangerous. The over-compaction of concrete is most often demonstrated by segregation of aggregates. The presented research deals with the determination of the optimal time and intensity of vibration of fresh concrete mixture to achieve the required physical properties of concrete, i.e. high compressive strength and modulus of elasticity of hardened concrete while reducing the negative effects of vibration, especially segregation of aggregates.

Acoustic Anthropogenic Noise Reduction In Pixel Priority Based Algorithm

Priority pixel enhancement for removing hindrances in acoustics. In this paper underwater sound speed gradient monitoring systems grieved in various conditions data monitoring. Compress and decompress sound waves of water molecules travel through underwater makes monitoring hindrances to ocean monitoring sensors produce dithered image data retrieving is based on pixel based algorithm to get the original point of data legible to enhance the part of the image in the priority enhancement methods in under water sound monitoring systems.

Dynamics of primitive streak regression controls the fate of neuromesodermal progenitors in the chicken embryo.

In classical descriptions of vertebrate development, the segregation of the three embryonic germ layers completes by the end of gastrulation. Body formation then proceeds in a head to tail fashion by progressive deposition of lineage-committed progenitors during regression of the primitive streak (PS) and tail bud (TB). The identification by retrospective clonal analysis of a population of neuromesodermal progenitors (NMPs) contributing to both musculoskeletal precursors (paraxial mesoderm) and spinal cord during axis formation challenged these notions. However, classical fate mapping studies of the PS region in amniotes have so far failed to provide direct evidence for such bipotential cells at the single-cell level. Here, using lineage tracing and single-cell RNA sequencing in the chicken embryo, we identify a resident cell population of the anterior PS epiblast, which contributes to neural and mesodermal lineages in trunk and tail. These cells initially behave as monopotent progenitors as classically described and only acquire a bipotential fate later, in more posterior regions. We show that NMPs exhibit a conserved transcriptomic signature during axis elongation but lose their epithelial characteristicsin the TB. Posterior to anterior gradients of convergence speed and ingression along the PS lead to asymmetric exhaustion of PS mesodermal precursor territories. Through limited ingression and increased proliferation, NMPs are maintained and amplified as a cell population which constitute the main progenitors in the TB. Together, our studies provide a novel understanding of the PS and TB contribution through the NMPs to the formation of the body of amniote embryos.

Ergotropy of bosonic quantum battery driven via repelling feedback algorithms

Feedback algorithms can be efficiently applied to control the basic characteristics of quantum batteries (QBs): the ergotropy, the charging power, the storage capacity and others. We invent here two alternative approaches, target repeller and speed gradient feedback, to maximize the ergotropy for bosonic types of single-qubit based quantum batteries. We demonstrate the achievability of the control goal and discuss some pros and cons of both proposed algorithms.

Investigation of dynamic pressure fluctuations in closed hydraulic circuits as a function of centrifugal pump speed gradients

Electrical consumers, such as pumps, contribute towards the stable operation of the electrical power grid due to active and reactive power consumption. If the consumers are indirectly connected to the grid via power electronic converters, the positive contribution is reduced or non-existent. Consequently, the ability to compensate imbalances within the power grid is greatly reduced. A research project founded by the European Union is focusing on investigations to utilize power converter technology of pump drives for grid stabilization. But in order to stabilize the fluctuating power grid frequency rapid adjustments of the pump speed are required, which can cause major troubles in the hydraulic system. For instance, rapid changes in pump speed are causing the emission of hydro acoustic pressure waves into the pipe system, which are exciting the structure of the hydraulic system and lead to undesirable vibrations and noise emissions. Most critical is the direct excitation of natural frequencies in the entire piping system based on the inherent pressure fluctuations caused by transient fluid flow and pump speed changes. Converter control for grid-adaptive speed adjustment is only possible as long as there is no significant increase in dynamic pressure fluctuations in the whole hydraulic system. For this purpose, a research pump is operated with different rotational speed gradients in a closed hydraulic circuit. Dynamic pressure sensors were used to record the resulting pressure fluctuations at various locations of the hydraulic system. Additionally, an outlook towards an active reduction of the dynamic pressure fluctuations by means of a specially developed hydrodynamic actuator is given. These results are an initial step but of particular interest towards the knowledge of permissible grid adaptive speed control regimes, which can be applied to a pump in a hydraulic piping system.

Observations of SST‐Induced Wind Perturbations in the Leeuwin Current

AbstractSea surface temperature (SST) perturbations modify low‐level winds through the influence of air‐sea heat flux across the marine atmospheric boundary layer, mostly observable in the major western boundary current systems. In this study, we investigate the effects of SST on surface winds in a poleward‐flowing eastern boundary current system, the Leeuwin Current (LC), using the Advanced Very High‐Resolution Radiometer (AVHRR) SST and wind data from Cross‐Calibrated Multi‐Platform (CCMP) during 2009–2018. There exist robust linear relationships between perturbation SST and perturbation wind speed and their derivatives in the LC. The regression slopes between SST perturbations and wind perturbations appear to be higher in austral summer when the alongshore northward winds are strongly opposing the LC, however, the relationships in winter are statistically more robust when the LC and associated cross‐shore SST fronts are the strongest. Consistent with previous studies in the western boundary currents, crosswind perturbation wind speed gradient is the largest for the winds 80° (−100°) to the right (left) of the SST gradient in the LC region. The perturbation wind stress curl induced by the SST signature of the LC causes positive wind stress curl anomalies on the offshore edge of the LC, driving anomalous downwelling and would reduce surface chlorophyll a concentrations along the LC SST front as observed in satellite data, which may have implications in regional biogeochemistry.

Sound speed gradients in mud

Various methods have been used to estimate sound speed profiles in mud at the New England Mud Patch. Some of these methods show large sound speed gradients of order 10 s-1. New measurements of the seabed reflection coefficient exhibit an angle of intromission over three octaves in frequency; these data constrain the range of possible sound speed gradient values. The data indicate that sound speed gradients must be quite weak, i.e., much smaller than |10 s-1|. This conclusion is supported by core data which indicate nearly constant porosity in most of the mud layer.

On Finding the Right Sampling Line Height through a Parametric Study of Gas Dispersion in a NVB

The tracer gas method is one of the common ways to evaluate the air exchange rate in a naturally ventilated barn. One crucial condition for the accuracy of the method is that both considered gases (pollutant and tracer) are perfectly mixed at the points where the measurements are done. In the present study, by means of computational fluids dynamics (CFD), the mixing ratio NH3/CO2 is evaluated inside a barn in order to assess under which flow conditions the common height recommendation guidelines for sampling points (sampling line and sampling net) of the tracer gas method are most valuable. Our CFD model considered a barn with a rectangular layout and four animal-occupied zones modeled as a porous medium representing pressure drop and heat entry from lying and standing cows. We studied three inflow angles and six combinations of air inlet wind speed and temperatures gradients covering the three types of convection, i.e., natural, mixed, and forced. Our results showed that few cases corresponded to a nearly perfect gas mixing ratio at the currently common recommendation of at least a 3 m measurement height, while the best height in fact lied between 1.5 m and 2.5 m for most cases.

Assessing the Surface-Layer Stability over China Using Long-Term Wind-Tower Network Observations

Surface-layer stability is important in many processes, such as in the surface energy budget, atmospheric pollution, and boundary-layer parametrizations. Most previous studies on stability, however, conducted either theoretical or observational investigations at specific sites, thus leaving a gap with regard to the large-scale pattern. Here, wind-speed and temperature observations at multiple heights from the wind-tower network of China are used to estimate low-level stability during the 2009–2016 period. A series of data-quality-control procedures are conducted and data from 170 wind towers with more than 2 years of valid observations are selected. The degree of stability is classified by the Obukhov length, which is derived from the wind speed and temperature at 10 m and 70 m above ground level, combined with information regarding the roughness length. Overall, the occurrence frequency of surface-layer instability exhibits significant temporal and spatial variability, being particularly larger in spring and summer than in autumn and winter. The maximum frequency of summertime instability occurs in the time period 1000–1200 local solar time, approximately 2 h earlier than in autumn. Geographically, the peak instability frequency occurs much earlier in the day in north-west China than in other regions, likely owing to the arid and semi-arid land cover. Also noteworthy is the steady increase in instability frequency observed during the period analyzed here, likely resulting from the reduction in the vertical gradient of wind speed. Our findings call for explicit consideration of stability variability in the wind-energy industry and in fundamental boundary-layer investigations in China.

Switchbacks Explained: Super-Parker Fields—The Other Side of the Sub-Parker Spiral

Abstract We provide a simple geometric explanation for the source of switchbacks and associated large and one-sided transverse flows in the solar wind observed by the Parker Solar Probe (PSP). The more radial, sub-Parker spiral structure of the heliospheric magnetic field observed previously by Ulysses, ACE, and STEREO is created within rarefaction regions where footpoint motion from the source of fast into slow wind at the Sun creates a magnetic fieldline connection across solar wind speed shear. Conversely, when footpoints move from the source of slow wind into faster wind, a super-Parker spiral field structure is formed: below the Alfvén critical point, one-sided transverse field-aligned flows develop; above the Alfvén critical point, the field structure contracts between adjacent solar wind flows, and the radial field component decreases in magnitude with distance from the Sun, eventually reversing into a switchback. The sub-Parker and super-Parker spirals behave functionally as opposites. Observations from PSP confirm the paucity of switchbacks within rarefaction regions and immediately outside these rarefaction regions, we observe numerous switchbacks in the magnetic field that are directly associated with abrupt transients in solar wind speed. The magnetic field strength, the radial component of the magnetic field, the speed gradients, radial Alfvén speed, and the ratio of the sound speed to the radial Alfvén speed all conform to predictions based on the sub-Parker and super-Parker spirals within rarefaction regions and solar wind speed enhancements (spikes or jets), respectively. Critically, the predictions associated with the super-Parker spiral naturally explain the observations of switchbacks being associated with unexpectedly large and one-sided tangential flows.

PRISM3D: a 3-D reference seismic model for Iberia and adjacent areas

SUMMARY We present PRISM3D, a 3-D reference seismic model of P- and S-wave velocities for Iberia and adjacent areas. PRISM3D results from the combination of the most up-to-date earth models available for the region. It extends horizontally from 15°W to 5°E in longitude, 34°N to 46°N in latitude and vertically from 3.5 km above to 200 km below sea level, and is modelled on a regular grid with 10 and 0.5 km of grid node spacing in the horizontal and vertical directions, respectively. It was designed using models inferred from local and teleseismic body-wave tomography, earthquake and ambient noise surface wave tomography, receiver function analysis and active source experiments. It includes two interfaces, namely the topography/bathymetry and the Mohorovičić (Moho) discontinuity. The Moho was modelled from previously published receiver function analysis and deep seismic sounding results. To that end we used a probabilistic surface reconstruction algorithm that allowed to extract the mean of the Moho depth surface along with its associated standard deviation, which provides a depth uncertainty estimate. The Moho depth model is in good agreement with previously published models, although it presents slightly sharper gardients in orogenic areas such as the Pyrenees or the Betic-Rif system. Crustal and mantle P- and S-wave wave speed grids were built separately on each side of the Moho depth surface by weighted average of existing models, thus allowing to realistically render the speed gradients across that interface. The associated weighted standard deviation was also calculated, which provides an uncertainty estimation on the average wave speed values at any point of the grid. At shallow depths (<10 km), low P and S wave speeds and high VP/VS are observed in offshore basins, while the Iberian Massif, which covers a large part of western Iberia, appears characterized by a rather flat Moho, higher than average VP and VS and low VP/VS. Conversely, the Betic-Rif system seems to be associated with low VP and VS, combined with high VP/VS in comparison to the rest of the study area. The most prominent feature of the mantle is the well known high wave speed anomaly related to the Alboran slab imaged in various mantle tomography studies. The consistency of PRISM3D with previous work is verified by comparing it with two recent studies, with which it shows a good general agreement.The impact of the new 3-D model is illustrated through a simple synthetic experiment, which shows that the lateral variations of the wave speed can produce traveltime differences ranging from –1.5 and 1.5 s for P waves and from –2.5 and 2.5 s for S waves at local to regional distances. Such values are far larger than phase picking uncertainties and would likely affect earthquake hypocentral parameter estimations. The new 3-D model thus provides a basis for regional studies including earthquake source studies, Earth structure investigations and geodynamic modelling of Iberia and its surroundings.

Time-dependent multi-depot green vehicle routing problem with time windows considering temporal-spatial distance

Reducing distribution costs is one of the effective ways for logistics enterprises to improve their core competitiveness. Aiming at the multi-depot vehicle routing problem under the time-varying road network, this paper proposes an integer programming model with the minimum total costs by comprehensively considering the fixed costs of vehicles, penalty costs on earliness and tardiness, fuel costs and the effects of vehicle speed, load and road gradient on fuel consumption. A hybrid genetic algorithm with variable neighborhood search is developed to solve the problem. In the algorithm, the temporal-spatial distance is introduced to cluster the customers to generate an initial population to improve the quality of the initial solution. Adaptive neighborhood search times strategy and simulated annealing inferior solution acceptance mechanism are used to balance the diversification and exploitation in the algorithm iteration process. Numerical results show that the model and algorithm we proposed are rather effective. The research results not only deepen and expand the vehicle routing problem (VRP) theory research, but also provide a scientific and reasonable method for logistics enterprises to make the vehicle scheduling plan.

Finite-Differential Nonsmooth Speed-Gradient Control: Stability, Passivity, Robustness

New combined finite-differential versions of nonsmooth speed-gradient (SG) algorithms are proposed and examined. Sufficient conditions for stability and robustness of the closed loop system are est...

Storm surges in the Gulf of Finland of the Baltic Sea

The characteristics of storm surges in different regions of the Gulf of Finland in the second half of the XX and the beginning of the XXI centuries were investigated on the basis of tide gauge measurements of sea level, instrumental observations of the wind and data from the reanalysis of meteorological fields. A criterion for identifying storm surges, taking into account spatial changes in their intensity, is proposed. The results indicate that depending on the year and the location of the station, the number of storm surges varies in the Gulf of Finland in a wide range: from 0 - 1 to 16 - 52 cases per year. The average duration of storm surges varies from 6.7 to 9.0 hours, and the maximum reaches 26 to 96 hours. Shown that in recent decades, in most regions, there has been a tendency towards a decrease in the number of storm surges, their dispersion and sea level maximum. The distributions of the probabilities of wind and atmospheric pressure during storm surges are given. Estimates of two-dimensional probability densities indicate that during storm surges, winds blowing from the west and southwest with speeds of 4-13 m / s are most likely. At the northern coast and at the top of the bay, the most probable values of atmospheric pressure during storm surges are 995 hPa. On the southern coast of the Gulf of Finland, atmospheric pressure values of 1005 - 1015 hPa are most likely. The results obtained indicate that the atmospheric pressure over the Gulf of Finland during storm surges is not very low. This is due to the fact that the trajectories of the centers of cyclones causing storm surges pass north of the Gulf of Finland. Analysis of meteorological information also showed the presence of significant negative trends in interannual variations in the dispersion of the horizontal atmospheric pressure gradient, average values and maximums of wind speed. It is concluded that the revealed changes in the characteristics of storm surges are associated with a decrease in the intensity of cyclogenesis in the atmosphere over the Baltic Sea in recent decades.

Microstructure and mechanical properties of Ti-Ti2AlNb interface

Diffusion bonding of Ti2AlNb alloy using pure titanium (Ti) foil as an interlayer was carried out on superplastic forming and diffusion bonding special equipment by gas pressure loading method. The microstructure of Ti-Ti2AlNb interface was observed using scanning electron microscope and energy-dispersive spectrometer while the mechanical properties of the joints were evaluated by shear test. The results show that the thickness of Ti foil interlayer has a great influence on the microstructure and shear strength of the interface diffusion region. When the thickness of the intermediate layer is thin (25 µm), Ti, aluminum (Al), and niobium (Nb) elements are fully diffused with uniform element distribution through the diffusion region. The diffusion layer region presents uniform, fine, and disordered lamellar α-Ti + β-Ti dual-phase structure with high shear strength. When the thickness of Ti foil interlayer is thick (50 µm), the distribution of Al elements is relatively uniform through the diffusion region due to its smaller radius and faster diffusion speed, and Ti and Nb elements present gradient distribution from the middle to both sides. The diffusion layer region presents a coarse and long strip shape α-Ti + β-Ti dual-phase structure in the middle part and a fine needle-like or irregular α-Ti + β-Ti dual-phase structure in both side parts, with slightly lower shear strength. Temperature has a great influence on the microstructure and mechanical properties of the diffusion bonding joints. The diffusion region presents a black α-Ti strip area in the middle part with the width of about 10 µm at lower temperature (910°C) with poorer property, due to the grain growth of the parent metal, the property is slightly poorer when the temperature is too high (960°C), and the optimal temperature is 930°C with a higher shear strength.

An improved brain storm optimisation algorithm for energy-efficient train operation problem

This paper presents a new method to determine the optimal driving strategies of the train using an improved brain storm optimisation (IBSO) algorithm. In the proposed method, the idea of successful-parent-selecting frame is applied to improve the original brain storm optimisation (BSO) algorithm avoiding premature convergence in evolutionary process while dealing with complex problems. The objective of the algorithm is to minimise energy consumption of the train by finding the switching points. Furthermore, the speed limits, gradients, maximum acceleration and deceleration as well as the maximum traction and braking force varying with speed are taken into consideration to meet practical constraints. Finally the comparison simulations among four algorithms show that the energy-efficient train operation strategy obtained by IBSO algorithm are more superior under the same conditions.

Magnetohidrodinamičko kočenje i Džulov efekat zagrevanja kod rotirajuće ograničene cilindrične šupljine punjene tečnim metalom

The present research work investigates the MHD braking and Joules heating effect in a confined rotating cylindrical cavity packed with liquid metal. All walls, except the top and bottom portion of the sidewall, of the cylindrical cavity, are made of electrically as well as thermally conducting material. The cavity is exposed to both axial magnetic fields along with the axial temperature gradient, packed with the incompressible electrically conducting liquid. The MHD braking effect is experienced within the rotating liquid metal flow due to the presence of a strong axial magnetic field. It is discerned that MHD braking governs the primary, as well as secondary flow, and, reduces Joules heating effect. Moreover, the internal heat generation due to Joules heating is governed by rotating speed, Hartmann strength, and temperature gradient.

On the diurnal cycle and variability of winds in the lower planetary boundary layer: evaluation of regional reanalyses and hindcasts

To accurately calculate the impact of renewables on power production in complex electric power grids, high-resolution and ideally seamless data within the planetary boundary layer are required. Therefore, the quality of different regional reanalyses and hindcasts is evaluated with respect to the representation of the planetery boundary layer and related sub-daily processes. On the one hand, high resolution regional reanalysis from the UERRA (UE-SMHI, UE-UKMO) and a similar project (COSMO-REA6) are considered. On the other hand, two hindcasts based on the COSMO-REA6 configuration are included in this study, i.e. a simulation with perfect boundaries and a simulation additionally utilizing spectral nudging. The focus of the evaluation is on measurements at four flux towers that are not part of any assimilation procedure. In this paper, we will show that the model’s quality depends on both the complete model system – assimilation method, resolution and physical parameterization – as well as on the performance measure. The daily cycle is best depicted by the hindcasts and even COSMO-REA6 hardly introduces spurious variability. UE-SMHI (3D-Var) suffers from spin-up in particular visible at the elevated levels, whereas the spin-up is damped in UE-UKMO (4D-Var). Investigation of atmospheric stability reveals that diurnal variation of stratification is for the most part well reproduced, but strong deficits were found for all COSMO simulations in reproducing strong stratification and corresponding wind speed gradients. Moreover, an overestimation of superadiabatic lapse rates and corresponding overly weak turbulent mixing is found for UE-UKMO. Furthermore, a combination of ramp statistics and contingency tables is utilized to detect a clear advantage of sophisticated assimilation systems over hindcasts. The evaluation framework presented underpins the importance of ramp statistics and vertical measurement profiles, especially with respect to assessing long-term simulations.

Environmental parameters sensitivity analysis for the modeling of wind turbine noise in downwind conditions.

Modeling a wind turbine sound field involves taking into account the main aeroacoustic sources that are generally dominant for modern wind turbines, as well as environmental phenomena such as atmospheric conditions and ground properties that are variable in both time and space. A crucial step to obtain reliable predictions is to estimate the relative influence of environmental parameters on acoustic emission and propagation, in order to determine the parameters that induce the greatest variability on sound pressure level. Thus, this study proposes a Morris sensitivity analysis of a wind turbine noise emission model combined with a sound propagation model in downwind conditions. The emission model is based on Amiet's theory and propagation effects are modeled by the wide-angle parabolic equation. The whole simulation takes into account ground effects (absorption through acoustic impedance and scattering through surface roughness) and micrometeorological effects (mean refraction through the vertical gradient of effective sound speed). The final results show that the parameters involved in atmospheric refraction and in ground absorption have a significant influence on sound pressure level. On the other hand, in the context of this study the relative air humidity and the ground roughness parameters appear to be negligible on sound pressure level sensitivity.

Linear stability analysis of (Cu-Al2O3)/water hybrid nanofluid flow in porous media in presence of hydromagnetic, small suction and injection effects

In this paper, a stability analysis of a hybrid nanofluid flow between two parallel and stationnary plates filled with a porous medium was investigated. The hybrid nanofluid is composed of water as regular fluid, copper (Cu) and alumina (Al2O3) as nanoparticles. A mathematical modeling of the problem was developed by taking account other effects such as aspiration (suction/injection) and magnetic field. An eigenvalue differential equation namely the modified Orr-Sommerfeld equation governing the stability of the flow was derived and solved numerically by spectral collocation method with expansions in Chebyshev polynomials. The effect of the density of particles, suction/injection Reynolds number, Hartmann number, Darcy number and volume fraction on the flow stability was examined and presented. It was found the following: the Darcy number affects the stability of the flow, the suction/injection reduces the drag and the transition is delayed/prevented, the magnetic field makes the dissipation very important because the kinetic energy of the electrically conductive fluid is absorbed by the Lorentz force, and the volume fraction and the density of nanoparticles increased the inertia of the fluid which decreased the speed gradient and damped the disturbances.