Spectral Response Research Articles

An Empirical Line approach for Agrowing Camera Aerial Images of inland waters based on exponential fit and in situ water measurements

Abstract. With the advancement of technology in the area of remote sensing, monitoring the Earth's surface using multispectral cameras attached to unmanned aerial vehicles (UAV) has become promising. However, in many Earth observation applications, it is needed to make compatible the spatial data of images captured by high spatial resolution multispectral sensors with the spectral response of targets on the Earth's surface. This relation is obtained through a radiometric calibration. The empirical line method is commonly used to calibrate the spectral bands of sensors. Thus, applications of this method using linear fit have retrieved negative values in water bodies. So that, attempting different adjustments, as well different reference targets, can solve this issue. In this study, the water quality of small bodies of water was analysed using a Agrowing multispectral camera, which derived negative values when applying linear fit. The aim of this study, therefore, was to fit a radiometric calibration based on empirical line method for Agrowing camera in inland water applications. Besides of standard reference targets, water samples also were attempted because showed a lower radiance response than the darkest (black) calibration target. Two empirical line methods were applied to convert the digital number (DN) from the Agrowing images into remote sensing reflectance (Rrs): linear and exponential. The exponential method showed to be more appropriate, with greater accuracy, unlike the linear method.

Substantial improvement of InGaN/GaN visible-light polarization-induced self-depletion phototransistor by thermally oxidized Al2O3

Atomic layer deposited (ALD) Al2O3 acting as gate dielectric and surface passivation is widely adopted in power electronics but seldom used in optoelectronic fields for its sophisticated and expensive technology. Herein, a simple but efficient Al2O3 passivation is used in the fabrication of InGaN/GaN visible-light (VL) polarization-induced self-depletion field effect phototransistors (FEPTs), for suppressing the surface leakage and recombination. The Al2O3 layer obtained by thermal oxidation (TO) of 2-nm-thick thermally evaporated metal Al shows high electrical insulation and even better passivation effect than the ALD-Al2O3. As a result, the dark current of TO-Al2O3 passivated device decreases by about 2 orders of magnitudes; meanwhile, the photoresponse increases by about 65%. Under a weak VL illumination of 6.8 μW/cm2, the InGaN/GaN FEPT exhibits a large photo-to-dark current ratio of 3.1 × 108 and an ultrahigh shot-noise-limited detectivity of 1.9 × 1018 jones. In addition, the FEPTs exhibit a strong wavelength selectivity with a 600 nm/400 nm spectral response rejection ratio exceeding 5 × 105. All these performances show huge potential in emerging VL applications that are limited by the insufficiencies of current Si photodetectors.

Evaluation of consumer-grade wireless EEG systems for brain-computer interface applications.

With the growing popularity of consumer-grade electroencephalogram (EEG) devices for health, entertainment, and cognitive research, assessing their signal quality is essential. In this study, we evaluated four consumer-grade wireless and dry-electrode EEG systems widely used for brain-computer interface (BCI) research and applications, comparing them with a research-grade system. We designed an EEG phantom method that reproduced µV-level amplitude EEG signals and evaluated the five devices based on their spectral responses, temporal patterns of event-related potential (ERP), and spectral patterns of resting-state EEG. We discovered that the consumer-grade devices had limited bandwidth compared with the research-grade device. A late component (e.g., P300) was detectable in the consumer-grade devices, but the overall ERP temporal pattern was distorted. Only one device showed an ERP temporal pattern comparable to that of the research-grade device. On the other hand, we confirmed that the activation of the alpha rhythm was observable in all devices. The results provide valuable insights for researchers and developers when it comes to selecting suitable EEG devices for BCI research and applications.

Quantum efficiency enhancement of reflective GaAs photocathodes with exponential-doping structure generating a favorable built-in electric field

The rapid development of GaAs photocathodes has led to an increased focus on the attainment of high quantum efficiency. Three types of exponential-doping structures with a high to low doping concentration distribution from the interior to the surface are proposed for reflective GaAs emission layers. These three structures generate different built-in electric fields that facilitate photoelectron emission. The one-dimensional continuity equations for the increasing, constant, and decreasing types of built-in electric fields are derived, respectively. The electron concentration distribution and quantum efficiency varying with the wavelength are solved numerically by the finite difference method. The simulation results indicate that the quantum efficiency of the GaAs photocathode with the increasing type of built-in electric field is superior to that with the constant built-in electric field, while the GaAs photocathode with the decreasing type of built-in electric field shows the worst performance. Then, the designed GaAs photocathodes with the increasing and constant types of built-in electric fields are grown by metal-organic chemical vapor deposition and activated by cesium-oxygen alternating deposition. The measured spectral response curves show that the quantum efficiency of the GaAs photocathode with the increasing type of built-in electric field is higher in the whole band than that with the constant type of built-in electric field. In addition, the exponential-doping structure generating the increasing type of built-in electric field is beneficial for improving the surface potential barrier and increasing the surface electron escape probability.

Photodamage prediction model and optimal lighting system for polychrome artworks in museum

When lighting polychrome artworks in museum, the light sources are required not only to provide high-quality visual performance, but also to minimize the photodamage. Currently, though there are mature methods to calculate visual performance, how to predict the degree of photodamage remains a challenge, which leads to a lack of light sources satisfying both visual and protection requirements. Our study conducted a series of 294 accelerated aging experiments spanning over 11 years for materials commonly used in Chinese polychrome artworks, using isoenergetic white-light D55 and 10 different wavelengths of narrow-band light as experimental light sources. The mathematical model predicting the photodamage degree caused by intensity (I), exposure time (t), the relative spectral power distribution of the light source (S(λ)), and the irradiated material's relative spectral responsivity (P(λ)) to polychrome artworks was established, and the mean absolute percentage error of the model, as verified by experiments, was 11.63 %. Combined with the existing visual performance calculation methods, an optimal lighting algorithm that simultaneously meets high-quality visual performance and minimum photodamage was developed, followed by developing a new Spectrally Tunable White LEDs (STWLEDs) lighting system with 10 LED chips. It is found that the STWLEDs can adjust and output the optimal spectra and recommended illuminance according to the characteristics of polychrome artworks, thus realizing lighting with minimum photodamage, meanwhile, satisfying high-quality visual performance. After testing, as well as satisfying the requirements of visual performance, the average photodamage is reduced by 40.95 % with STWLEDs compared with the traditional WLEDs.

The Spectral Response Characteristics of Potassium in Camellia oleifera Leaves at Different Growth Stages

The Spectral Response Characteristics of Potassium in Camellia oleifera Leaves at Different Growth Stages

Self-driven Te0.65Se0.35/GaAs SWIR Photodiode with Spectral Response to 1.55 μm for Broadband Imaging and Optical Communication

Self-driven Te0.65Se0.35/GaAs SWIR Photodiode with Spectral Response to 1.55 μm for Broadband Imaging and Optical Communication

Insight into interfacial dynamics of photogenerated carriers in Cs3Bi2I9/Au heterostructure nanocomposites for high-sensitivity broadband photodetection with negative photoconductivity

The negative photoconductivity (NPC) effect is becoming an increasingly significant factor in the development of next-generation optoelectronics. However, research in the field of NPC-dominated optoelectronics remains in its infancy and frequently encounters challenges related to fabrication complexity, slow photoresponse speed, instability, and a limited spectral response range. Herein, a Cs3Bi2I9/Au heterostructure nanocomposite was prepared via a simple self-assembly process utilizing electrostatic interactions with Au nanoparticles (NPs) and lead-free Cs3Bi2I9 nanoplates. The Cs3Bi2I9/Au nanocomposite-based photodetectors (PDs) demonstrate a broadband photoresponse (405–1550 nm), enhanced rise/fall times (27.2/40.0 µs), and reduced noise density (4.7 × 10−13 A/Hz1/2 at 1 Hz). In contrast to the positive photoconductivity (PPC) effect observed in colloidally synthesized Cs3Bi2I9 nanoplate-based PDs, the NPC can be attributed to the decrease in photocurrent under light illumination during the processes of recombination and trapping of photogenerated carriers induced by the incorporation of Au NPs. These findings are expected to provide valuable insights into achieving high-performance NPC-dominated PDs by regulating the dynamics of photogenerated carriers in perovskite heterostructures.

Evaluating the general V(λ), mismatch spectral quality factor index ƒ₁ and the uncertainty of photometers

The general term photometry refers to the measurement of light and its perceived brightness; it can be applied to various purposes, including lighting design, display calibration, and the setting of safety standards. A device used for measuring light is called a light meter or photometer. Ideally, such devices should have a spectral responsivity-that is, they should respond to light in a way which mimics the human eye's sensitivity to different wavelengths. The sensitivity of the human eye is described by the Commission Internationale de l'Éclairage, CIE, luminous efficiency function, V(λ), a plot of the sensitivity of the eye versus wavelength over the visible region, from violet, approximately 380 nm, through red, approximately 780 nm. In practical applications, it is usually preferable to detect light with silicon or selenium photodetectors and measure the electrical current generated. These photodetectors are sensitive to a wide range of wavelengths, including those outside of the visible spectrum: ultraviolet (UV) and infrared (IR). However, due to its nature, the spectral responsivity of silicon and selenium photodetectors is also different from that of the human eye. For example, silicon photodetectors are much more sensitive to infrared radiation, which is imperceptible to human vision. This in turn leads to erroneous light measurements when using the direct raw response of the detector. The spectral quality factor and , indicating the mismatch between the spectral responsivity and the CIE luminous efficiency function V(λ), is the most crucial characteristic of photometers. The general mismatch index , denoted as V(λ), delineates the disparity between a photometer's relative spectral responsivity and the spectral luminous efficiency function for photopic vision, V(λ). It's highly probable that photometers will adopt white light-emitting diode (LED) sources as calibration references going forward. This transition may necessitate refining the general V(λ) mismatch index's definition, possibly through alternative normalization methods for or by introducing a different assessment function for evaluating mismatches . In this research, spectral quality factor for the photometer NIS-2 has been determined with value 3.8%. This percentage value is classified the photometer NIS-2 as medium quality. The uncertainty was determined through a calculation performed using my Microsoft Excel program, and the final value obtained is 0.010.

Unveiling the influence of dopants on structural, defect chemistry, morphological and optical characteristics of NiO nanostructures

Abstract In this paper, undoped and doped (Fe, Co and Fe-Co) nickel oxide (NiO) nanostructures have been synthesized using co-precipitation method. Prepared samples were characterized for the structural, compositional, morphological and optical properties using x-ray diffraction, scanning electron microscopy (SEM), Energy dispersive spectrocopy (EDS), UV-visible spectroscopy and photoluminescence spectroscopy. Structural analysis confirmed the single cubic phase formation of undoped and doped samples. Defect chemistry showed that Fe-Co co-doped NiO possesses a lower density of defects than other samples. SEM results revealed the agglomeration of particles. EDS results confirmed the presence of Ni, O, Fe and Co in the respective undoped and doped samples. Optical analysis revealed the band edge shifts with the incorporation of dopants in the NiO crystal lattice confirmed the variation of band gap energy. Emission peaks were observed in the UV and visible regions. The Incorporation of dopants in the crystal lattice causes variation of emission centers. Surface oxygen vacancies and imperfections significantly impact the emission characteristics of NiO. Variable spectral response of NiO with dopant incorporation has potential for optoelectronic applications.

Single-Particle Spectroelectrochemistry: Revealing the Electrochemical Tuning Mechanism of Chemical Interface Damping in 1,2-Benzenedithiol-Adsorbed Single Gold Nanorods.

Chemical interface damping (CID) is a newly proposed plasmon damping pathway based on interfacial hot-electron transfer from metal to adsorbate molecules. However, achieving in situ tunability of CID in single gold nanorods (AuNRs) remains a considerable challenge. Here, we present the CID effect induced by benzene 1,2-dithiol (BDT) molecule adsorption on single AuNRs and the effective electrochemical tunability of CID in BDT-adsorbed AuNRs immobilized on an indium tin oxide (ITO) surface. Manipulations of the electrochemical potential alter the electron density of AuNRs, thereby influencing and tuning the localized surface plasmon resonance (LSPR) spectrum, with cathodic potential blueshifting and anodic potential redshifting. The strong adsorption of BDT on Au induced CID in single AuNRs. The potential-induced LSPR scattering spectra of BDT-adsorbed AuNRs for linear potential sweep showed a stable LSPR spectral response, irrespective of the concentrations of BDT molecules. Due to the involvement of two Au-S bonds, BDT molecules have a higher free adsorption energy and a lower desorption rate on the Au surface. This resulted in a stable LSPR spectral response for a linear electrochemical potential sweep. Furthermore, a constant anodic and cathodic potential application showed the tunability of the CID at the BDT-Au interface.

Adopting Buffer Layer for Improving Signal‐to‐Noise Ratio of Broadband Photomultiplication Type Organic Photodetectors

AbstractThe photomultiplication type organic photodetectors (PM‐OPDs) are prepared with structure of ITO/PNDIT‐F3N/F8BT/Y6‐1O:P3HT (100:3, wt/wt)/Al, containing hole traps formed with P3HT surrounded by Y6‐1O in active layers. The PM‐OPDs exhibit external quantum efficiency (EQE)>100% in the spectral response range from 310 to 910 nm, resulting from electron tunneling injection assisted by trapped hole near ITO electrode. The incorporation of F8BT buffer layers can induce the markedly decreased dark current density (JD) due to the large electron injection barrier. The light current density (JL) of PM‐OPDs exhibits slightly decreased by inserting F8BT buffer layers due to the enhanced electron tunneling injection assisted by the more trapped holes near ITO electrode. The signal‐to‐noise ratio (SNR) of PM‐OPDs achieves over 40‐fold increment by inserting appropriate thickness of F8BT buffer layers, resulting from the markedly decreased JD and reasonably high JL. The optimal PM‐OPDs exhibit excellent photodetection capability with EQE of 4200% at 360 nm and 6600% at 850 nm, associated with the specific detectivity of 3.9 × 1011 Jones at 360 nm and 9.7 × 1011 Jones at 850 nm.

Enhanced Photodetection Performance of InBiSe3/ReS2 Polarization-Sensitive Heterostructure Photodetectors.

Individual anisotropic two-dimensional (2D) materials have been widely applied for developing polarization-sensitive photodetectors, but they often suffer from limitations in photoresponsivity, detection range, etc. To overcome these challenges, van der Waals (vdW) heterostructures created by stacking different 2D materials provide a promising solution to enhance the performance of the photoelectronic device. In this work, a novel polarization-sensitive photodetector is developed by leveraging a heterojunction formed by InBiSe3 and anisotropic ReS2 nanoflakes. The InBiSe3/ReS2 vdW heterostructure devices exhibit excellent photodetection performance with a high photoresponsivity (R)of 7.68 AW-1 and a specific detectivity (D*)up to 1.26×1011 Jones as well as an external quantum efficiency (EQE) of 1790% under 532 nm laser irradiation. Additionally, benefiting from the broadband light absorption of InBiSe3 crystals together with the pronounced anisotropic electronic and optical characteristics of ReS2 flakes, the devices demonstrate a broad spectral response range from 402 to 1006 nm with a distinct polarization sensitivity of 1.24. Moreover, the devices exhibit extraordinary optical communication and high contrast polarimetric imaging capacity. This work demonstrates the enhanced photodetection performance with the InBiSe3/ReS2 vdW heterostructures operating in a photoconductive mode and illustrates promising application of these heterostructures in integrated optoelectronic systems.

Construction of direct Z-scheme Sn3O4/WO3 heterostructure photocatalyst for enhanced Congo red degradation and Cr(Ⅵ) reduction performance

The development of well-designed architectures is crucial in accelerating the transport of photon-generated carriers in composite photocatalysts. In this study, a direct Z-scheme Sn3O4/WO3 (SW) photocatalyst was successfully fabricated utilizing a straightforward hydro/solvothermal approach, where Sn3O4 nanosheets (NSs) grew in-situ onto WO3 nanorods (NRs) uniformly. The optimal SW-2 composite exhibits a remarkable reduction rate of 93.5 % for Congo Red (CR) within 40 min, with a rate constant (k) of 0.075 min−1. This performance surpasses that of pristine Sn3O4 and WO3, which have rate constants of 0.027 min−1 and 0.018 min−1, respectively. Additionally, the SW-2 composite effectively removes 89.2 % of Cr(VI) over 100 min, achieving a k value of 0.019 min−1, which is higher than that of Sn3O4 (0.013 min−1) and WO3 (0.001 min−1). Furthermore, the photocatalytic degradation performance of the recovered samples retains their photocatalytic degradation performance after five consecutive experimental cycles, indicating excellent durability. The enhanced photocatalytic performance can be attributed to the construction of a direct Z-scheme heterostructure, which not only broadens the spectral response range, bur also ensures efficient separation of photoexcited carriers and fosters robust photo-redox capacity within the composite. This study is expected to provide some valuable insights into the design and synthesis of Z-scheme heterojunction photocatalysts, aimed at addressing pressing environmental pollution challenges.

Recent Advances in Organic Photodetectors

Organic photodetectors (OPDs) have garnered significant attention in fields such as image sensing, health monitoring, and wearable devices due to their exceptional performance. This review summarizes recent research advancements in materials, structures, performance, and applications of narrowband organic photodetectors, hybrid organic–inorganic perovskite photodetectors, flexible organic photodetectors (FOPDs), and photomultiplication type organic photodetectors (PM-OPDs). Organic semiconductors offer substantial potential in optoelectronic devices owing to their low cost, ease of processing, and tunable spectral response. Hybrid perovskite materials extend the spectral response range, FOPDs meet the demands of wearable devices, and PM-OPDs enhance sensitivity, allowing for the detection of weak light signals. Through innovations in materials, structural optimization, and improvements in manufacturing processes, the performance of OPDs has seen significant enhancement. This article also explores the application prospects of these technologies in medical monitoring, optical communications, and image sensing.

Photoinduced modulation and the effect of CNT loading on field effect transistor characteristics of CNT/ZnO/PVDF composite.

CNT/ZnO/PVDF polymer composite phototransistor is studied for the effect of CNT loading and the photoinduced modulation on its transfer characteristics. XRD study shows that the induced strain in the composite is due to the addition of CNT to the ZnO/PVDF composite. The percentage of β-phase present in PVDF is estimated through Raman spectroscopy and the composite's spectral response is determined by UV-Vis absorbance spectroscopy. From the DC electrical conductivity study it is found that the percolation threshold for the composites is obtained for 0.3 wt% of CNT, and 0.44 wt % of CNT loading makes the composite conductive. On adding 1 wt% of CNT, the electrical conductivity of the ZnO/PVDF composite increases 40 times (~ 0.2 μS/m). The temperature-dependent DC conductivity shows that the conductivity of the composites changes from variable range hopping (VRH) to band conductance upon an increase in CNT loading above the percolation threshold and exhibits a negative temperature coefficient (NTC). Two terminal photoconductivity studies are done to understand the photo enhancement and sensitivity of all the devices. PE hysteresis studies show that the polarization of the composites increases drastically from 0.05 μC/cm2 below the percolation threshold to 10 - 30 μC/cm2 above the percolation threshold of CNT in the composite. To study the effect of interfacial polarization on photoconductivity, the composite is studied in a three-terminal device format using SiO2 as a gate dielectric. A band diagram analysis of the oxide-composite and CNT/ZnO interface is done to understand the mechanism behind the photoinduced field effect on transfer characteristics and the effect of CNT loading. The switching behavior and decay time under UV illumination are studied to understand the effect of CNT loading and photoinduced polarization. The persistent photoconductivity decreases and the charge collection efficiency of the FET increases as the CNT loading increases.

Real-time optical fibre near-infrared chromatic dispersion analyser using collocated optical fibre gratings

We present what we believe to be a novel optical fibre device for real-time measurements of near-infrared chromatic dispersion of a liquid medium from 1100 nm to 1700 nm. This inline optical fibre chromatic dispersion analyser is based upon collocated fibre long-period gratings written adjacently in the core by femtosecond laser inscription yielding 8 attenuation bands associated with different cladding modes, yielding 8 independent measurements. This fibre device is tested on a series of chemical compounds associated with wines. The results for each compound yielded distinctive chromatic responses. A machine learning pipeline was developed that successfully clustered and classified spectral responses of the different chemicals to illustrate the distinctive responses. The limits of detection for these fibre devices ranged from 1×10−3 to 6×10−5 mol/L for the compounds associated with wines, demonstrating the potential usefulness of an optical fibre chromatic dispersion analyser is capable of monitoring in real-time effective chromatic dispersion that is not offered by any current technology.

Temporal coherence shapes cortical responses to speech mixtures in a ferret cocktail party

Perceptual segregation of complex sounds such as speech and music simultaneously emanating from multiple sources is a remarkable ability that is common in humans and other animals alike. Unlike animal physiological experiments with simplified sounds or human investigations with spatially broad imaging techniques, this study combines insights from animal single-unit recordings with segregation of speech-like sound mixtures. Ferrets are trained to attend to a female voice and detect a target word, both in presence and absence of a concurrent equally salient male voice. Recordings are made in primary and secondary auditory cortical fields, and in frontal cortex. During task performance, representation of the female words becomes enhanced relative to the male in all, but especially in higher cortical regions. Analysis of the temporal and spectral response characteristics during task performance reveals how speech segregation gradually emerges in the auditory cortex. A computational model evaluated on the same voice mixtures replicates and extends these results to different attentional targets (attention to female or male voices). These findings underscore the role of the principle of temporal coherence whereby attention to a target voice binds together all neural responses coherently modulated with the target, thus ultimately forming and extracting a common auditory stream.

Influence of laser energy on CuO@ZnO nanoparticles for enhancing spectral responsivity

Influence of laser energy on CuO@ZnO nanoparticles for enhancing spectral responsivity

Temperature-modulated acetone monitoring using Al2O3-coated evanescent wave fiber optic sensors

This paper presents an experimental study of a fiber-optic-based acetone sensor and its temperature effects for use as a breath analyzer to detect acetone in exhaled breath. The study employs fiber optic evanescent wave-based acetone sensing, utilizing sputter coated Aluminium Oxide (Al2O3)-coated probes fabricated via clad modification technique. The optical fibers were coated with Al2O3 to achieve thicknesses of 247.03 nm, 334.05 nm, and 468.75 nm. The sensor probes were characterized using, Field Emission Scanning Electron Microscopy (FESEM), Energy Dispersive Spectroscopy (EDS), X-ray Diffraction (XRD), Ultraviolet-Visible (UV-Vis) Spectroscopy, and Spectroscopic Ellipsometry for uniformity, elemental, optical constants, and thickness of the Al2O3. The spectral responses of the probes were analyzed for acetone concentrations ranging from 0 to 100 ppm, with temperature modulation from room temperature to 100 °C. The probe with a ∼334 nm thick Al2O3 coating exhibited the highest response, reaching 6.2 % at 100 °C in 100 ppm acetone. Linear regression revealed that the ∼334 nm coated probe had the highest sensitivity at 5.98 counts/ppm. The sensor showed response and recovery times of approximately 12 and 17 seconds, respectively. This study underscores the stability and repeatability of temperature-modulated Al2O3-coated fiber optic sensors for selective acetone detection in various non-invasive applications.