Acoustic Metamaterials Research Articles

Genetic-algorithm-assisted design of chiral honeycomb membrane acoustic metamaterials for broadband noise suppression

Low-frequency sound wave reduction is hardly feasible for traditional sound absorbers such as porous media. In contrast, locally resonant acoustic metamaterials act as spatial frequency filters, effectively reducing low-frequency noise. However, these materials can have narrow bandgaps, add extra mass to the main system, and function only within a specifically adjusted frequency range. Therefore, this paper proposes a methodology for designing three-dimensional (3D) chiral honeycomb membrane-type acoustic metamaterials (MAM) based on acoustic circular dichroism (ACD), negative effective mass, and local resonance mechanisms (LRM). The paper also uses the genetic algorithm (GA) to maximize sound transmission attenuation and widen bandgaps. The accuracy of the simulations is validated with available experimental data. The key idea of the present study is to automatically design a MAM structure using modern optimization tools. A developed GA aims to maximize the average sound transmission loss (STL) across the desired low-frequency range of 0–850 Hz by optimizing the value of structural parameters associated with the configurations of masses, including rotation and linear offset, as well as their geometrical dimensions, including length and width. COMSOL Livelink with MATLAB is employed as a practical co-simulation tool to find an optimum value for structural parameters. Results indicate a 35% improvement in average STL along with an ultra-wide bandgap with a 507% bandgap coverage factor (BGCF) in the frequency range of interest, verifying the reliability of the developed algorithm. In addition, sound mitigation incidence is justified by exploring the negative effective parameters of the unit cell and displacement vector fields. The proposed designs demonstrate superior performance as both initial and optimized models broke the mass law within the investigated frequency range. Finally, the effect of the selected geometrical parameters on the objective function is observed through sensitivity analysis. This study presents the practical use of optimization algorithms to develop MAMs.

Uncertainty quantification of acoustic metamaterial bandgaps with stochastic material properties and geometric defects

Acoustic metamaterials are a subject of increasing study and utility. Through designed combinations of geometries with material properties, acoustic metamaterials can be built to arbitrarily manipulate acoustic waves for various applications. Despite the theoretical advances in this field, however, acoustic metamaterials have seen limited penetration into industry and commercial use. This is largely due to the difficulty of manufacturing the intricate geometries that are integral to their function and the sensitivity of metamaterial designs to material batch variability and manufacturing defects. Capturing the effects of stochastic material properties and geometric defects requires empirical testing of manufactured samples, but this can quickly become prohibitively expensive with higher precision requirements or with an increasing number of input variables. This paper demonstrates how uncertainty quantification techniques, and more specifically the use of polynomial chaos expansions and spectral projections, can be used to greatly reduce sampling needs for characterizing acoustic metamaterial dispersion curves. With a novel method of encoding geometric defects in a 1D, interpretable, resolution-independent way, our uncertainty quantification approach allows for both stochastic material properties and geometric defects to be considered simultaneously. Two to three orders of magnitude sampling reductions down to ∼100 and ∼101 were achieved in 1D and 7D input space scenarios, respectively. Remarkably, this reduction in sampling was possible while preserving accurate output probability distributions of the metamaterial performance characteristics (bandgap size and location).

Sound absorption performance of honeycomb metamaterials Inspired by Mortise-and-Tenon structures

To address the limitations of traditional honeycomb sandwich structures in attenuating mid to low-frequency sounds, particularly in configurations with minimal thickness and weight, this study introduces an innovative honeycomb acoustic metamaterial incorporating the traditional Chinese mortise-and-tenon joint. We systematically investigate the acoustic absorption characteristics of the modified honeycomb structure through theoretical analysis, empirical validation, and numerical simulations. Our experimental setup maintained consistent geometric parameters across all trials and demonstrated that the resonance frequency of the modified honeycomb structure decreased by 10 % relative to its conventional counterpart. We conducted detailed analyses on the influence of micropore positioning, tenon geometric dimensions, and micropore diameters on the acoustic performance. Notably, elongating the tenon from 2 mm to 6 mm resulted in a 15 % reduction in resonance frequency, whereas increasing the micropore-to-tenon distance from 0 mm to 4 mm led to a 30 % increase. The integration of the mortise-and-tenon joint significantly enhances the mid to low-frequency sound absorption performance of the honeycomb panels. This improvement is achieved while preserving the structural benefits of low panel thickness and shallow cavity depth, alongside simplified processing of micropores. Our findings elucidate a promising approach to augmenting the acoustic properties of lightweight structural materials, thereby extending their application potential in noise control engineering. This study not only contributes a novel perspective to the design and optimization of acoustic metamaterials but also highlights the potential for integrating traditional architectural techniques with modern material science to enhance noise control solutions.

Optimization of acoustic porous material absorbers modeled as rigid multiple microducts networks: Metamaterial design using additive manufacturing

This research presents a strategy to enhancing sound absorption in porous acoustic metamaterials through the optimization of micro-duct networks. The study employs a combination of analytical and numerical methods, systematically adjusting micro-duct diameters within a 2D grid to optimize absorption coefficients at specific frequency bands. The Finite Element Transfer Method (FETM) is utilized for modeling, supported by a multi-objective function influenced by the surface impedance of the network. This approach ensures practical applicability and manufacturability of the designed metamaterial. A significant aspect of the study is the development of an analytical mobility matrix for each microduct, integrated through the Transfer Matrix Method using the visco-thermal dissipation theory. This integration results in a physically coherent model, for which a semi-analytical sensitivity analysis related to the microduct diameters can be directly performed. The optimization employs the Method of Moving Asymptotes (MMA), effectively managing the complexity associated with a large number of design variables. Subsequently, the optimized structure is adapted into a 3D grid, facilitating prototype creation using Additive Manufacturing Technology (AMT) with a specific polymer material. The research methodology is validated through four distinct test cases, each demonstrating the efficacy and adaptability of the optimization tools and techniques. Experimental validation, conducted using an impedance tube, indicates a significant shift in the first absorption maximum from 2500 Hz to 1000 Hz, achieved without altering the material thickness. Additional validation through 3D Finite Element Method (FEM) modeling, which includes visco-thermal effects, further confirms the acoustic efficiency of the final designs. While the potential for achieving lower sub-wavelength conditions is recognized, the study opts for simpler structures, considering the current limitations of 3D printing technology. This study contributes to both theoretical understanding and practical application in acoustic material design, emphasizing the potential for customizing materials to specific frequency ranges. The integration of FETM modeling with MMA provides a systematic and effective approach for optimizing acoustic materials, particularly in enhancing absorption at lower frequencies.

Electrical-Modulated Flexible Acoustic Metamaterial: Enhancing Low-Frequency Absorption via an Ionic Electroactive Polymer.

The growing concern over low-frequency noise pollution resulting from global industrialization has posed substantial challenges in noise attenuation. However, conventional acoustic metamaterials, with fixed geometries, offer limited flexibility in the frequency range adjustment once constructed. This research unveiled the promising potential of ionic electroactive polymers, particularly ionic polymer-metal composites (IPMCs), as a superior candidate to design tunable acoustic metamaterial due to its bidirectional energy conversion capabilities. The previously perceived limitations of the IPMC, including slow reaction and high energy expenditure, owning to its inherent sluggish intermediary ionic mass transport process, were astutely leveraged to expedite the attenuation of low-frequency sound energy. Both our experimental and simulation results elucidated that the IPMC can generate voltage potentials in response to acoustic pressure at frequencies significantly higher than those previously established. In addition, the peak absorption frequency can be effectively shifted by up to 45.7% with the application of a 4 V voltage. By further integration with a microperforated panel (MPP) structure, the developed metamaterial absorbers can achieve complete sound absorption, which was continuously tunable under minimal voltage stimulation across a wide frequency spectrum. In addition, a microslit structure IPMC metamaterial absorber was designed to realize modulation of the perforation rate, and the absorption peak can be shifted by up to 79.2%. These findings signify a pioneering application of ionic intelligent materials and may pave the way for further innovations of tunable low-frequency acoustic structures, ultimately advancing the pragmatic deployment of both soft intelligent materials and acoustic metamaterials.

Low-Frequency Sound-Insulation Performance of Labyrinth-Type Helmholtz and Thin-Film Compound Acoustic Metamaterial.

This paper presents a type of acoustic metamaterial that combines a labyrinth channel with a Helmholtz cavity and a thin film. The labyrinth-opening design and thin-film combination contribute to the metamaterial's exceptional sound-insulation performance. After comprehensive research, it is observed that in the frequency range of 20-1200 Hz, this acoustic metamaterial exhibits multiple sound-insulation peaks, showing a high overall sound-insulation quality. Specifically, the first sound-insulation peak is 26.3 Hz, with a bandwidth of 13 Hz and giving a transmission loss of 56.5 dB, showing excellent low-frequency sound-insulation performance. To further understand the low-frequency sound-insulation mechanism, this paper uses the equivalent model method to conduct an acoustic-electrical analogy, construct an equivalent model of the acoustic metamaterial, and delve into the sound-insulation mechanism at the first sound-insulation peak. To confirm the validity of the theoretical calculations, physical experiments are carried out by 3D printing experimental samples. The analysis of the experimental data has yielded results that are consistent with the simulation data, providing empirical evidence for the accuracy of the theoretical model. The material has significant practical application value. Finally, various factors are studied in depth based on the established equivalent model, which can provide valuable insights for the design and practical engineering application of acoustic metamaterials.

The mechanism of adjusting the low-frequency ultra-wide band gap within lightweight spherical superstructue

Conventional resonant structures can be effective in obtaining broadband, but it is still a challenge to design small-sized and lightweight acoustic metamaterials with a low-frequency ultra-wideband. This paper proposes a new approach of designing a lightweight spherical localized resonance superstructure with adjustable stiffness ratio, and the mechanism of adjusting the low-frequency ultra-wide forbidden band is revealed. Then, the correlation between the zero value of its dynamic equivalent mass and the stiffness ratio of the system is studied. It is found that not only is the upper bound of the negative mass effectively broadened, but also the lower bound is successfully lowered only by adjusting the stiffness ratio of the sphere. Most importantly, based on the regulation mechanism with adjustable stiffness ratio, the lower boundary of the band gap is lowered from 171 Hz to 141 Hz, and the upper boundary is increased from 445 Hz to 710 Hz. Therefore, the low-frequency ultra-wideband of 141–710 Hz is obtained only by adjusting the stiffness ratio of the system and the Finite Element Method, which is highly consistent with theoretical analyses. Obviously, the mechanism of obtaining the low-frequency wideband through adjusting the stiffness ratio not only provides a novel idea for adjusting the low-frequency ultra-wideband, but also provides theoretical guidance for the developing the small-size and lightweight acoustic devices, so it would have potential application in the field of vibration and noise reduction.

Current developments in elastic and acoustic metamaterials science.

The concept of metamaterial recently emerged as a new frontier of scientific research, encompassing physics, materials science and engineering. In a broad sense, a metamaterial indicates an engineered material with exotic properties not found in nature, obtained by appropriate architecture either at macro-scale or at micro-/nano-scales. The architecture of metamaterials can be tailored to open unforeseen opportunities for mechanical and acoustic applications, as demonstrated by an impressive and increasing number of studies. Building on this knowledge, this theme issue aims to gather cutting-edge theoretical, computational and experimental studies on elastic and acoustic metamaterials, with the purpose of offering a wide perspective on recent achievements and future challenges. This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1)'.

Group-theoretic analysis of symmetry-preserving deployable structures and metamaterials.

Many deployable structures in nature, as well as human-made mechanisms, preserve symmetry as their configurations evolve. Examples in nature include blooming flowers, dilation of the iris within the human eye, viral capsid maturation and molecular and bacterial motors. Engineered examples include opening umbrellas, elongating scissor jacks, variable apertures in cameras, expanding Hoberman spheres and some kinds of morphing origami structures. In these cases, the structures either preserve a discrete symmetry group or are described as an evolution from one discrete symmetry group to another of the same type as the structure deploys. Likewise, elastic metamaterials built from lattice structures can also preserve symmetry type while passively deforming and changing lattice parameters. A mathematical formulation of such transitions/deployments is articulated here. It is shown that if [Formula: see text] is Euclidean space, [Formula: see text] is a continuous group of motions of Euclidean space and [Formula: see text] is the type of the discrete subgroup of [Formula: see text] describing the symmetries of the deploying structure, then the symmetry of the evolving structure can be described by time-dependent subgroups of [Formula: see text] of the form [Formula: see text], where [Formula: see text] is a time-dependent affine transformation. Then, instead of considering the whole structure in [Formula: see text], a 'sector' of it that lives in the orbit space [Formula: see text] can be considered at each instant in time, and instead of considering all motions in [Formula: see text], only representatives from right cosets in the space [Formula: see text] need to be considered. This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1)'.

Elastic wave control in reticulated plates using Schwarz primitive cells.

In this work, the Schwarz primitive unit cell is used as the building block of different types of metastructures for steering and focusing elastic vibrations. The emergence of a Bragg-type bandgap when constructing a two-dimensional plate from such unit cells is experimentally validated. It is demonstrated that increasing both mass and porosity of the Schwarz primitive leads to a decrease in the frequency of the out-of-plane propagating wave targeted in this study. By arranging these modified Schwarz primitive unit cells in constant and graded layouts, two-dimensional plates with an embedded metabarrier and a metalens are numerically designed. The metabarrier protects an interior area of the plate from the propagating waves on a wide frequency band (approx. 1.4-3.4 kHz). Equally, the refractive index profile necessary for gradient index lenses is obtained via a progressive variation of the added mass or, alternatively, the porosity of the unit cell over a rectangular area. For the first time, bending of the out-of-plane mode towards the focusing point is practically validated in a challenging mesoscale experiment requiring the assembly of different three-dimensional printed sections of the plate. The increased porosity design is advantageous not only in terms of overall lightweight, but also towards additive manufacturing as it requires less material.This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1)'.

Broadband surface wave manipulation by periodic barriers in unsaturated soil.

Periodic wave barriers have been widely used to manipulate elastic waves propagating in saturated and single-phase soil due to their attenuation zone properties. However, it is difficult to promote application of periodic barriers in unsaturated soils due to their complex constitutive relationship. In this study, manipulation of surface waves by periodic in-filled trench barriers in unsaturated soil has been studied based on the periodic theory. The dispersion relations of a periodic structure for surface waves in unsaturated soil are determined. The attenuation mechanism of evanescent surface waves is revealed. Next, the effects of several key parameters of unsaturated soil on the attenuation zones of the periodic in-filled trench barriers are comprehensively discussed. It is found that in a particular range for material parameter, the surface waves are attenuated over the entire frequency range due to the viscosity of fluid. Finally, a periodic in-filled trench barrier is designed according to a field test of ground vibration induced by a train, and its performances in mitigating surface waves propagating in unsaturated and saturated soils are conducted and compared by conducting analysis in time domain. This investigation provides a new insight for manipulating surface waves by periodic barriers. This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1)'.

Design and experimental validation of a finite-size labyrinthine metamaterial for vibro-acoustics: enabling upscaling towards large-scale structures.

In this article, we present the design and experimental validation of a labyrinthine metamaterial for vibro-acoustic applications. Based on a two-dimensional unit cell, different designs of finite-size metamaterial specimens in a sandwich configuration including two plates are proposed. The design phase includes an optimization based on Bloch-Floquet analysis with the aims of maximizing the band gap and extruding the specimens in the third dimension while keeping the absorption properties almost unaffected. By manufacturing and experimentally testing finite-sized specimens, we assess their capacity to mitigate vibrations in vibro-impact tests. The experiments confirm a band gap in the low- to mid-frequency range. Numerical models are employed to validate the experiments and to examine additional vibro-acoustic load cases. The metamaterial's performances are compared with benchmark solutions, usually employed for noise and vibration mitigation, showing a comparable efficacy in the band gap region. To eventually improve the metamaterial's performance, we optimize its interaction with the air and test different types of connections between the metamaterial and the homogeneous plates. This finally leads to metamaterial samples largely exceeding the benchmark performances in the band gap region and reveals the potential of interfaces for performance optimization of composed structures.This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1)'.

Elastic metasurfaces for Scholte-Stoneley wave control.

In this work, we investigate the dynamics of Scholte-Stoneley waves (SSWs) travelling along elastic metasurfaces, e.g. thin resonant structures embedding mechanical oscillators, placed at the interface between solid and fluid. To this purpose, an analytical dispersion law, valid in the long-wavelength regime, is derived and used to reveal the hybridization of SSWs with the collective resonance of the mechanical oscillators and the conversion of SSWs into leaky modes within the fluid. The analytical predictions are validated through numerical simulations that include both dispersive and harmonic analysis. Our findings disclose the capabilities of elastic metasurfaces in filtering, trapping and converting SSWs along fluid-solid interfaces, thus supporting the design of novel devices for solid-fluid interaction across various engineering applications, including microfluidics. This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1)'.

Effects of interfacial debonding on the stability of finitely strained periodic microstructured elastic composites.

Predicting failure initiation in nonlinear composite materials, often referred to as metamaterials, is a fundamental challenge in nonlinear solid mechanics. Microstructural failure mechanisms encompass fracture, decohesion, cavitation, compression-induced contact and instabilities, affecting their unconventional static and dynamic performances. To fully take advantage of these materials, especially in extreme applications, it is imperative to predict their nonlinear behaviour using reliable, accurate and computationally efficient numerical methodologies. This study presents an innovative nonlinear homogenization-based theoretical framework for characterizing the failure behaviour of periodic reinforced hyperelastic composites induced by reinforcement/matrix decohesion and interaction between contact mechanisms and microscopic instabilities. Debonding and unilateral contact between different phases are incorporated by employing an enhanced cohesive/contact model, which features a special nonlinear interface constitutive law and an accurate contact formulation within the context of finite strain continuum mechanics. The theoretical formulation is demonstrated using periodically layered composites subjected to macroscopic compressive loading conditions along the lamination direction. Numerical results illustrate the ways in which debonding phenomena, in conjunction with fibre microbuckling, may influence the critical loads of the examined composite solid. The sensitivity of the results obtained through the proposed contact-cohesive model at finite strain with respect to its implementation is also explored. This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1)'.

Dynamic continualization of mechanical metamaterials with quasi-periodic microstructure.

This article focuses on characterizing a class of quasi-periodic metamaterials created through the repeated arrangement of an elementary cell in a fixed direction. The elementary cell consists of two building blocks made of elastic materials and arranged according to the generalized Fibonacci sequence, giving rise to a quasi-periodic finite microstructure, also called Fibonacci generation. By exploiting the transfer matrix method, the frequency band structure of selected periodic approximants associated with the Fibonacci superlattice, i.e. the layered quasi-periodic metamaterial, is determined. The self-similarity of the frequency band structure is analysed by means of the invariants of the symplectic transfer matrix as well as the transmission coefficients of the finite clusters of Fibonacci generations. A high-frequency continualization scheme is then proposed to identify integral-type or gradient-type non-local continua. The frequency band structures obtained from the continualization scheme are compared with those derived from the Floquet-Bloch theory to validate the proposed scheme. This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1).'

Guiding near-source elastic waves in a semi-infinite medium.

In this work, we propose elastic metamaterials with phase discontinuities to steer the propagation of near-source bulk waves in a semi-infinite elastic medium. Our design exploits an array of embedded subwavelength resonators with tailored masses to attain a complete phase shift spanning [Formula: see text]. This phase control allows for diverse wave functionalities, such as directional refraction and energy focusing. Through the use of dispersion diagrams and the generalized Snell's law, along with a multiple scattering formulation, we analytically demonstrate the effectiveness of our design in achieving the desired wavefront manipulation. The proposed design has the potential to advance the field of guiding elastic waves using metamaterials and find practical applications in areas such as isolating ground-borne vibrations in densely urbanized regions and energy harvesting. This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1)'.

Novel 4D-printed multi-stable metamaterials: programmability of force-displacement behaviour and deformation sequence.

The unique properties of metamaterials are determined by the configuration and spatial arrangement of artificially designed unit structures. However, the configuration and mechanical properties of conventional metamaterials are challenging to reverse and adjust. Based on curved beams, two types of novel three-dimensional (3D) multi-stable metamaterials with reconfigurable deformation and tunable mechanical properties are designed and fabricated using a four-dimensional (4D) printing method. The effects of temperature and curved-beam thickness on the force-displacement curves and multi-stable snapping sequence of the 3D multi-stable metamaterials are investigated by finite-element analysis (FEA) and experiments. In addition, based on the designed four-branch multi-stable metamaterials, three- and six-branched multi-stable structures are designed by changing the number of curved-beam branches. It is shown that, owing to shape memory effects, the 3D multi-stable metamaterials can realize mechanical programmability, and the multi-stable deformation sequence can be precisely regulated by varying the temperature and curved-beam thickness. These 4D-printed multi-stable metamaterials provide valuable contributions to the design of programmable multi-stable metamaterials and their applications in soft robots and intelligent structures. This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1)'.

Surface wave mitigation by periodic wave barriers under a moving load: theoretical analysis, numerical simulation and experimental validation.

Periodic wave barriers (PWB) open a new window for vibration mitigation. However, the Doppler effect is rarely considered in most of the previous investigations on the control of ambient vibration induced by moving loads. This article reveals the significance of the speed and frequency of moving loads on surface waves, and improves the design method of PWB for ambient vibration reduction and isolation. First, the theoretical expression of the main frequency band of surface waves propagating in an elastic half-space caused by a moving load was obtained. Comparisons with the numerical results under three different types of traffic loads were also conducted and good agreement was found. Second, the theoretical expression and numerical results were verified by experimental studies. Some inherent properties of wave propagation caused by a moving load in an elastic half-space were also revealed. Third, two kinds of PWBs, i.e. periodic empty trench barrier and periodic pile barrier, were introduced to mitigate wave propagation. It has been confirmed that if the attenuation zones of PWB match the target frequency bands given by the theoretical expression, good vibration mitigation can be achieved. This article is part of the theme issue 'Current developments in elastic and acoustic metamaterials science (Part 1)'.

Active acoustic metamaterials with on-demand bulk modulus and full mass density tensor

Active acoustic metamaterials with on-demand bulk modulus and full mass density tensor

Optimization of novel plate acoustic metamaterials and modulation of the low-frequency bandgap

Based on the local resonance mechanism, five new acoustic metamaterial plate structures with low-frequency bandgaps are proposed in this paper. The two new structures obtained by heuristic structural design are capable of suppressing vibrations over a large frequency range in the low-frequency range of 0-400 Hz, which is promising for practical applications. The mechanism of bandgap generation is found to be a shift in the form of local resonance. Among the three original models, model C has the smallest transmission coefficient T min of −154.6. Analysis of the group and phase velocity diagrams reveals that the change in frequency has a great influence on the energy transfer, speed and direction of the wave in the structure. The heuristic structural design allows the mass block of model B1 to undergo angular state changes, which ultimately realizes the regulation of the bandgap position and the total bandgap width within a certain range. It is also found that the variation of the bandgap properties has a certain regularity with the change of the structural parameters.