Sodium Solutions Research Articles

The effects of counter ion on CO2 capture performance of amino acid salt solutions for direct air capture applications

Direct CO2 capture from the atmosphere has received growing attention driven by the imperative of achieving global net-zero emission targets. Amino acid salt solutions are promising candidates for liquid-based direct air capture processes. Utilised as a neutralized salt by reacting initially with hydroxides, it has been speculated that their performance may vary with the type of counter ion present in the solution. This work investigates the influence of counter ions, potassium, sodium, and lithium, of amino acid salt solutions on the physical properties, the CO2 absorption capacities, and the CO2 absorption kinetics under atmospheric CO2 concentration levels. The potassium-containing amino acid solutions exhibited significantly lower viscosities and mildly elevated densities compared to sodium- and lithium-containing ones. At 25 °C, the potassium-prolinate solution demonstrated the highest viscosity (8.5 mPa⋅s), whereas K-glycinate exhibited the lowest viscosity (2.5 mPa⋅s). Additionally, potassium-based solutions consistently displayed the highest CO2 mass transfer coefficients, followed by sodium- and lithium-containing ones. The CO2 mass transfer coefficient was highest for potassium-prolinate (2.99 mmol m−2⋅s−1⋅kPa−1) with the lowest rate observed for potassium-β-alaninate (1.68 mmol m−2⋅s−1⋅kPa−1). Interestingly, the type of counter ion had minimal impact on the CO2 absorption capacity, with potassium-based solutions exhibiting only a slightly elevated capacity compared to sodium- and lithium-based solutions. Specifically, potassium-lysinate displayed the highest CO2 absorption capacity (0.7 mol CO2 /mol amine), while potassium-β-alaninate showed the lowest (0.65 mol CO2/mol amine). It should be noted that all lithium-based solutions of all amino acids formed precipitates during CO2 absorption. From a practical and operational perspective, these findings suggest that the potassium salt solution of amino acids would be the optimal choice for direct air capture applications due to their enhanced solubility and CO2 mass transfer rates compared to the corresponding sodium and lithium counter ion salt solutions.

Regeneration of a Fire‐Resistant Fluid‐Fouled Strong Base Anion Resin using a Caustic Solution with Citric Acid as a Surfactant

AbstractFire Resistant Fluid (FRF), used in turbine governing systems, transforms during operation, forming substituted phenol and phosphoric acid. The use of strong Base Anion Resin (SBA resin) to reduce the Total Acid Number (TAN) of FRF is widespread. However, the regeneration of these oil‐fouled resins is crucial due to their high cost and the challenges associated with their environmental disposal. In this study, we present a novel method for recovering exhausted resin by treating it with an aqueous solution of citric acid, followed by regeneration with a caustic soda solution. We optimized the recovery percentage in the ion exchange capacity by testing varying concentrations of the citric acid solution under different reaction conditions. The highest recovery of ion exchange capacity achieved was 55 % after soaking for 16 hours in a 5 % citric acid solution, followed by regeneration with a 5 % NaOH solution. The efficacy of citric acid in this research was further explored through a Density Functional Theory (DFT) study. This study is significant as it is the first to demonstrate the successful regeneration of oil‐fouled resins with high ion exchange capacity using citric acid, a more environmentally friendly and cost‐effective alternative.

Effect Of The Composition Of The Etching System MF-HCl (M = Li+, Na+, NH4+) on the gas-sensitive properties of Ti3C2Tх/Tioх nanocomposites

The influence of the nature of MF-HCl etching systems (M = Li+, Na+, NH4+) on the process of synthesis of Ti3C2Tx MXenes on the basis of Ti3AlC2 MAX-phase, microstructure, phase purity, interlayer distance, composition of functional surface groups, thermal behavior and yield of the obtained products has been studied. The room temperature sensing properties of Ti3C2Tx receptor layers deposited by microplotter printing were studied with respect to a wide range of gas analytes (H2, CO, NH3, NO2, NO2, O2, benzene, acetone, methane and ethanol). Increased sensitivity to ammonia was revealed for the MXenes obtained by exposure to hydrochloric acid solutions of sodium and ammonium fluorides and to carbon monoxide for the sample synthesized using the LiF-HCl system. High responses (~20–30% to 100 ppm NO2) were observed for all three receptor materials, but sensor recovery processes were significantly hampered. To improve the sensing characteristics, Ti3C2Tx sensing layers were subjected to relatively low-temperature heat treatment in an air atmosphere to form Ti3C2Tx/TiOx nanocomposites. It was found that a high and selective oxygen response at very low operating temperatures (125-175°C) was observed for the MXenes partially oxidized, which is particularly characteristic of the material produced using the HCl-NaF system.

Whole cell affinity for 4-amino-5-hydroxymethyl-2-methylpyrimidine (HMP) in the marine bacterium Candidatus Pelagibacter st. HTCC7211 explains marine dissolved HMP concentrations.

Vitamin B1 is a universally required coenzyme in carbon metabolism. However, most marine microorganisms lack the complete biosynthetic pathway for this compound and must acquire thiamin, or precursor molecules, from the dissolved pool. The most common version of Vitamin B1 auxotrophy is for thiamin's pyrimidine precursor moiety, 4-amino-5-hydroxymethyl-2-methylpyrimidine (HMP). Frequent HMP auxotrophy in plankton and vanishingly low dissolved concentrations (approximately 0.1-50 pM) suggest that high-affinity HMP uptake systems are responsible for maintaining low ambient HMP concentrations. We used tritium-labelled HMP to investigate HMP uptake mechanisms and kinetics in cell cultures of Candidatus Pelagibacter st. HTCC7211, a representative of the globally distributed and highly abundant SAR11 clade. A single protein, the sodium solute symporter ThiV, which is conserved across SAR11 genomes, is the likely candidate for HMP transport. Experimental evidence indicated transport specificity for HMP and mechanistically complex, high-affinity HMP uptake kinetics. Km values ranged from 9.5 pM to 1.2 nM and were dramatically lower when cells were supplied with a carbon source. These results suggest that HMP uptake in HTCC7211 is subject to complex regulation and point to a strategy for high-affinity uptake of this essential growth factor that can explain natural HMP levels in seawater.

Binding properties of synthesized CS glasses activated by alkaline components

The paper presents the synthesis and evaluation of hydration and binding properties of individual minerals with glass-like structures in silicate systems, most often found in technogenic materials based on phosphorus and blast furnace slags. This work aims to determine the optimum composition of CS glasses to obtain binders with given properties, the hydration of glasses of different silicate and aluminosilicate compositions in the presence of solutions of soda, sodium hydroxide, and sodium metasilicate was investigated. The results of X-ray phase and differential-thermal analysis, and infrared spectrum are given, and the hydration structure of the calcium oxide-silicon oxide-alkali component system has been studied. The analysis of hydrate neoplasms of the studied binding systems shows that the most optimal conditions for the synthesis of stone strength with stable physical and mechanical properties are created in the presence of gel-like phase reinforced by hydrosilicates and hydroaluminosilicates of alkaline and alkaline-alkaline-earth composition, characterized by fiber-like structure and possessing the ability to epitaxial fusion with each other, as well as gel-like phase, which they reinforce.

Chemical Activation Boosted Interface Interaction between Poly(tetrafluoroethylene-co-hexafluoropropylene) Film and Silver Coating.

To enhance the interfacial adhesion between poly(tetrafluoroethylene-co-hexafluoropropylene) (FEP) film and functional coatings, such as silver (Ag) coating, among others, the surface activation of FEP film has to be performed. Among various activation strategies, chemical activation, such as using naphthalene sodium system, is one of the most efficient methods. However, the effect of chemical activation on the interface interaction between the activated FEP and functional coating is rarely investigated. Herein, the FEP film was activated by naphthalene sodium solution under different conditions, and then the Ag layer was coated onto its surface by vacuum Ag deposition. Based on experimental results and density function theory (DFT) calculation, it is indicated that oxygen-containing functional groups (such as C=O and C-OH groups), introduced onto the surface of FEP by the chemical activation, play a key role in boosting the interface interaction, which is due to the strong interaction between the oxygen-containing functional groups and Ag atoms. In addition, the concentration of naphthalene sodium solution, activation time, and winding speed of Ag- deposition can have a significant impact on the microstructures of Ag coating and the interfacial adhesion between the activated FEP and Ag coating. Under the conditions of high concentration (0.9 M), medium activation time (15 min), and high winding speed (0.8 m min-1), there is the best interface adhesion.

Formononetin ameliorates dextran sulfate sodium-induced colitis via enhancing antioxidant capacity, promoting tight junction protein expression and reshaping M1/M2 macrophage polarization balance

Ulcerative colitis (UC) is a complex, refractory inflammatory bowel disease characterized impared intestinal mucosal barrier and imbalanced M1/M2 macrophage polarization mediating its progression. Formononetin (FN), a bioactive isoflavone with established anti-inflammatory and immunomodulatory properties, shows promise in mitigating UC, yet its therapeutic and underlying mechanisms remain unclear. In this study, colitis was induced in mice by administering 2.5% (w/v) dextran sulfate sodium (DSS) solution for 7 days. Oral (25, 50, and 100 mg/kg) FN for 10 days significantly ameliorated colitis symptoms in a dose-dependent manner, by mitigating body weight loss, reducing disease activity index (DAI), colonic weight, and colonic weight index, while enhancing survival rates and colonic length. Histological analysis revealed FN remarkably suppressed inflammatory damage in colonic tissues. Furthermore, FN modulated the expression of pro- and anti-inflammatory cytokines and enhanced antioxidant capacity. Notably, FN treatment significantly enhanced the expression of tight junction (TJ) proteins (claudin-1, ZO-1, occludin) at both protein and mRNA levels in the colon tissues, suggesting improved intestinal barrier function. Crucially, FN inhibited macrophage infiltration in colonic tissues and rebalanced M1/M2 macrophage polarization. While, macrophage depletion largely abrogated FN’s protective effects against colitis, indicating a crucial role for macrophages in mediating FN’s therapeutic response. Overall, FN effectively alleviated colitis primarily via modulating inflammatory cytokine expression, enhancing antioxidant capacity, upregulating TJs proteins expression, and remodeling M1/M2 macrophage polarization equilibrium. These findings suggest that FN could be the next candidate to unlocking UC’s treatment challenge.

Quantitative assessment of early caries lesion activity using novel dye-enhanced fluorescence imaging

ObjectivesThis study aimed to evaluate the validity of the dye-enhanced quantitative light-induced fluorescence (DEQLF) method for assessing early enamel caries activity. MethodsSeventy extracted human teeth with early enamel caries on smooth surfaces were included. Two dentists evaluated the caries activity using the Nyvad system followed by the DEQLF method. The teeth were hydrated with distilled water for 60 s, dehydrated with compressed air for 10 s, and stained with 100 μM fluorescein sodium solution for 10 s. White and fluorescent images were captured using a QLF-D 2+ Billuminator. The change in fluorescence (ΔΔG) was calculated using image analysis software. Independent-sample t-tests were performed to evaluate the difference in ΔΔG between active and inactive lesions for both DEQLF and conventional quantitative light-induced fluorescence (QLF) methods. Receiver operating characteristic (ROC) curve analysis was used to assess the validity of ΔΔG for distinguishing lesion activity using the area under the ROC curve (AUROC). ResultsAmong the 70 caries lesions, 33 were active and 37 were inactive. Using the DEQLF method, the ΔΔG for active lesions (3.8 ± 5.6) was significantly higher than that for inactive lesions (1.0 ± 2.5) (P < 0.05). With the conventional QLF method, there was no significant difference in ΔΔG between active (-1.1 ± 1.7) and inactive (-1.3 ± 1.7) lesions. DEQLF-derived ΔΔG demonstrated an AUROC of 0.72, a sensitivity of 0.67, and a specificity of 0.76. ConclusionsApplying the DEQLF method to human teeth enabled the quantitative assessment of lesion activity based on dye penetration. DEQLF-derived ΔΔG values showed significant differences based on lesion activity status and demonstrated high validity in distinguishing lesion activity. Clinical significanceClinicians can use the DEQLF method, which involves applying a fluorescent dye for 10 s prior to conventional QLF, to objectively quantify and distinguish the activity status of early enamel caries, potentially replacing the traditional reliance on subjective visual assessments.

Long-lasting antistatic hydrophilic polyethylene terephthalate fabric using greener reagents

AbstractPolyethylene terephthalate (PET) is the most common synthetic polymer used in the textile sector by virtue of its unique superior performance attributes. However, the comfort characteristics of PET fabrics, such as their inadequate sweat-absorbing capability, low affinity for most dyestuff classes, and susceptibility to the accumulation of electrostatic charge, make them unfavorable compared to natural fibers. Rendering PET fabrics with hydrophilic and antistatic properties is difficult due to the lack of reactive functional groups. Herein, a long-lasting eco-friendly strategy to impart some desirable properties to PET fabrics was developed. The PET fabric was saponified in an aqueous caustic soda solution, followed by treatment with an amino acid, namely lysine, aspartic acid, serine, tyrosine, or cysteine, as a coupling agent, and eventually, the fabric was finished with the protein biopolymer gelatin using the pad-dry-cure method. The effects of treatment of PET fabric with the aforementioned reagents on its surface hydrophilicity, roughness, antistatic, thermal stability, ultraviolet protection, air permeability, yellowness, bending stiffness, and tensile properties were monitored. The discrepancy between the chemical structures of the untreated and finished fabrics was determined using Fourier transform infrared spectroscopy as well as by determining the carboxylic and nitrogen contents. The morphological and crystal structures of the treated fabrics were examined using scanning electron microscopy and X-ray diffraction pattern, respectively. The results indicate that a maximum add-on was obtained upon treatment of the saponified PET fabrics with 0.5 M lysine followed by 7.5% (on the weight of the fiber) gelatin using the pad-dry-cure method.The finished PET fabrics exhibited improved hydrophilic and antistatic properties with adequate protection against UV rays.Ingeneral, treatment of PET fabrics with gelatin, using a bi-functional amino acid as a coupling agent, is an effective and durable method to improve some performance and comfort features of PET fabric without having a remarkable negative effect on the fabric’s mechanical properties.

The effect of decoupling humidity control on aerosol drug delivery during HFNC for infants.

Aerosol therapy is commonly used during treatment with high-flow nasal cannula (HFNC) in the intensive care unit (ICU). Heated humidification inside the HFNC tubing circuit leads to unwanted condensation, which may greatly limit the efficiency of drug delivery. In this study, we aimed to investigate whether a novel humidification system, which decouples temperature and humidity control, can improve the delivered dose. In a bench study setup, fluorescein sodium solution was nebulized using a vibrating-mesh nebulizer in an infant HFNC circuit to measure the delivered dose, with a conventional versus a novel decoupled humidifier. The deposition of fluorescein inside each breathing circuit component and a final collection filter at the end of the nasal cannula was collected and quantified with a UV-vis spectrometer. Droplet sizes at different sections of the breathing circuit were measured by laser diffraction. Three air flow rates: 5, 10 and 15 L/min, and two nebulizer positions: (1) at the humidifier and (2) after the inspiratory tube, were tested. The delivered dose decreased with increasing flow rate for the conventional setup and was higher when the nebulizer was placed after the inspiratory tube. Turning off the conventional humidifier 10 minutes before and during nebulization did not improve the delivered dose. The decoupled humidifier achieved a significantly higher (p = .002) delivered dose than the conventional setup. The highest delivered dose obtained by the decoupled humidifier was 62.4% when the nebulizer was placed after the humidifier, while the highest dose obtained for the conventional humidifier was 36.3% by placing the nebulizer after the inspiratory tube. In this bench study, we found that the delivered dose for an infant HFNC nebulization setup could be improved significantly by decoupling temperature and humidity control inside the HFNC circuit, as it reduced drug deposition inside the breathing circuit.

Real-time in vivo confocal laser endomicroscopic imaging of equine endometrium: Preliminary observations and feasibility study

Endometrial health is vital for the reproductive efficiency of broodmares and accurate diagnostic testing is crucial for directing the best treatment options and outcomes. Confocal laser endomicroscopy (CLE) is an endoscopic technique for obtaining in-vivo, real-time microscopic imaging of tissues using a fiber optic probe. CLE relies on induced tissue fluorescence and fluorescein sodium, given intravenously, is the contrast agent most used in human medicine. This study aimed to determine the feasibility of CLE for imaging equine endometrium and determine a standard dose of fluorescein sodium to achieve optimal cellular imaging. In-vivo CLE was performed on 44 mares, and the images were compared with routine histopathological analysis of endometrial biopsies. No adverse reactions occurred after IV fluorescein sodium administration and a dose of 4 mg/kg was established (0.04 mL/kg of 10 % fluorescein sodium solution) to achieve optimal image contrast. CLE enabled multiple regions of the endometrium to be assessed quickly. Distinct tissue architecture patterns could be appreciated using CLE, and the luminal epithelium could be assessed for integrity (ulceration) and exocytosed inflammatory cells. Endometrial gland distribution, density, shape, and epithelial height were evaluated. Blood vessels were clearly outlined, and inflammatory cells and fibrosis were discernable within the interstitium. Image quality varied between mares, and the stage of oestrous cycle may have been a factor of influence. This novel imaging modality enables collection of “virtual” biopsies and facilitates critical assessment of multiple regions of the uterus compared with the standard histopathologic assessment of a single random tissue biopsy.

Repercussion of fiber content on the mechanical, thermal, and thermomechanical properties of natural fibers reinforced thermoplastic composites for automotive application

Natural fibers are becoming very popular as a reinforcement in composite materials owing to their benefits, such as low-price, lightweight, availability, and environmental friendliness. In this study, abaca fiber-reinforced polypropylene (PP) and high-density polyethylene (HDPE) composites were created with the help of the injection molding method. Prior to composite fabrication, abaca fibers were chemically treated with a 5 wt% caustic soda (NaOH) solution to improve the bonding between the abaca fibers and the matrix and to enhance their properties. Scanning electron microscopy (SEM) was utilized to assess the fiber surface microstructures before as well as after the chemical treatment, along with the fractured surfaces of tensile specimens. The mechanical properties, such as tensile, bending, and impact strength, of abaca/PP and abaca/HDPE composites were evaluated and compared. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) methods were utilized to investigate the thermal behavior of composites. Also, the dynamic mechanical analysis (DMA) method was utilized to explore the thermomechanical properties of the fabricated composites. The outcomes of the experimental findings showed that abaca/PP composite with 10 and 20 wt% fibers is the best choice of material to be used in the automobile industry.

Impaired Saltiness Perception Contributes to Higher Sodium Intake Among Patients With Chronic Kidney Disease: A Cross-Sectional Two-Center Study

Dietary sodium restriction is important in the prognosis of patients with chronic kidney disease (CKD). The association between saltiness perception and sodium intake among CKD patients is unclear, and the factors that influence saltiness are also not fully understood. We evaluated saltiness perception in CKD patients employing a cost-effective saltiness perception test using sodium solutions and evaluated the association between saltiness perception, sodium intake, and the influencing factors. CKD outpatients not undergoing dialysis were enrolled from two medical centers and underwent saltiness perception tests together with 24-hour urine collections to measure daily sodium intake. Participants who perceived saltiness using the test solution containing 25mM sodium were regarded to have "preserved" saltiness perception, while those unable to perceive saltiness were regarded as having "impaired" saltiness perception. Of the total 132 participants, the median daily sodium intake was 3.36g (range; 0.51-9.95g/day), and 43 (32.6%) were ex- or current smokers. When participants were divided into 3 groups (G) according to daily sodium intake level: low (G1; 0.51-2.61g/day), middle (G2; 2.62-3.99g/day), and high (G3; 4.06-9.95g/day), there was an obvious difference in impaired saltiness perception between three groups: 6.8% in G1, 50.0% in G2 and 86.4% in G3 (P value=8.035 × 10-14, Cochran-Armitage test). In a multiple regression analysis in which the saltiness perception was adopted as a subjective variable, smoking habit (ex- or current smoker) and nonadherence to dietary sodium restriction were identified as significant explanatory variables. We revealed the clear relationship between higher daily sodium intake and impaired saltiness perception that is related to nonadherence to dietary sodium restriction and smoking habit, both of which could be intervened by nutritional counseling and public health education.

Development of a Method for Utilization of Quarry Drainage Waters of a Limestone Mine to Ensure Environmental Safety

A method has been developed for the disposal of quarry drainage waters, which ensures that they are not discharged into an open reservoir and reduce their anthropogenic impact on the environment. The direction of drainage waters from the limestone quarry into the technological process of preparing the raw charge reduces the consumption of circulating soda solutions and ensures higher extraction of potassium sulfate from soda solutions. The average increase in the yield of potassium sulfate from an increase in the content of sulfates in the liquid phase of the raw nephelinelimestone-soda charge is 4.0 tons per day or 1,460 tons per year.

КОМБИНИРОВАННЫЕ ТВОРОЖНО-ОВОЩНЫЕ ЗАПЕКАНКИ ИЗ МЕСТНОГО СЫРЬЯ ДЛЯ РАЦИОНАЛЬНОГО ПИТАНИЯ

The aim of the study is to develop a recipe for combined curd-vegetable casseroles from local raw materials with improved organoleptic and physicochemical properties. A comprehensive study was conducted that allowed theoretically and experimentally substantiating the feasibility of using turnips as a functional ingredient in the preparation of curd-vegetable casserole. The following quality indicators were studied in the experimental samples of culinary products: mass fraction of fat, protein, total sugars, ascorbic acid content; sanitary and microbiological indicators: the number of mesophilic aerobic and facultative anaerobic microorganisms (QMAFAnM), the number of yeast and mold fungi, and coliform bacteria (BGCP). The applied research methods are the mass fraction of fats according to GOST 31902-2012, the mass fraction of protein by the Kjeldahl method according to GOST 10846-91, the mass fraction of ascorbic acid was determined by titration with a solution of sodium 2,6-dichlorophenolindophenolate according to GOST 24556-89, the mass fraction of sugars – by the iodometric method, by diluting the sanitary and microbiolo¬gical indicators of QMAFAnM according to GOST 10444.15-94, counting the colonies of mold fungi and yeast according to GOST 10444.12-2013 and coliform bacteria according to GOST 31747-2012. The study was carried out at the Department of Public Catering Technology and Processing of Plant Raw Materials of the Federal State Budgetary Educational Institution of Higher Education "BashSAU", Republic of Bashkortostan. In the recipe for making cottage cheese and vegetable casserole, carrots were replaced with turnips in a ratio of 25 to 100 %. It was found that 100 % replacement of carrots with turnips in a culinary product improves organoleptic properties (taste, color) and physicochemical indicators (increase in vitamin C by 5.5 times). Sanitary and microbiological indicators (QMAFAnM, coliform bacteria, yeast and mold) corresponded to the required SanPiN 2.3.2.1078-01 standards.

Anthropozoonotic parasitoses of dogs and cats in the urban ecosystem of Vladivostok, Russia

To investigate the role of domestic dogs and cats in the spread of parasitoses in the Vladivostok urban ecosystem. Biological materials from 782 dogs and 189 cats were used in the research, which were examined by methods of complete parasitological autopsy, microscopy and flotation of faecal samples using saturated solutions of zinc sulfate and sodium nitrate.Fourteen parasite taxa have been identified: nematodes (Nematoda) Ancylostoma caninum, Dirofilaria immitis, Toxascaris leonina, Toxocara canis, T. mystax, Uncinaria stenocephala, Taenia sp., T. hydatigena; tapeworms (Cestoda) Diphyllobothrium latum, Dipylidium caninum, Hydatigera taeniaeformis; flukes (Trematoda) Metagonimus sp.; and parasitic alveolates (Conoidasida) Cystoisospora sp., C. felis. The paper presents the values of the prevalence of infection and statistical reliability of their differences for different groups of animals, depending on gender and age. Nematodes were the core taxa of the parasitofauna identified. Explanations for the results obtained are offered and possible sources of human infection are described. Despite the fact that parasitic‐faunal complexes in the ecosystem of a modern city are much less branched and represented by fewer species than in the wild, there remains a high risk of human infection with zoonotic parasites in urban biocenoses due to the high level of intensive population interactions. Therefore, there is a requirement of high alertness of supervisory authorities in relation to anthropozoonotic parasitoses in an urban environment.

SODIUM, MONOETHANOLAMMONIUM AND POLYETHYLENE POLYAMMONIUM CITRATES AQUEOUS SOLUTIONS ELECTROCHEMICAL PROPERTIES

pH and conductometric study of aqueous (0.1 ÷ 9.0)⋅10-3 mol/l solutions of sodium (Na3Cit), monoethanolammonium (H3Cit⋅3MEA) and polyethylenepolyammonium (kH3Cit⋅3PEPA) citrates was carried out. Features of the electrochemical behavior of monoethanolamine and polyethylenepolamine ammonium citrates aqueous solutions were revealed in comparison with Na3Cit. As the temperature increases from 293 to 303 K, the pH values and Na3Cit solutions molar electrical conductivity increase. Due to hydrolytic processes, when diluting H3Cit⋅3MEA solutions, a change in pH is observed from slightly acidic to slightly alkaline, in contrast to Na3Cit. An increase in temperature (in the region of 293–308 K) leads to an increase in the medium acidity, in contrast to sodium citrate solutions, which is accompanied by an atypical decrease in molar electrical conductivity at the same H3Cit⋅3MEA content. It has been shown that an increase in temperature in the range of 293-308 K leads to a decrease in H3Cit⋅3MEA aqueous solutions pH, in contrast to Na3Cit and kH3Cit⋅3PEPA solutions, which is accompanied by an atypical decrease in molar electrical conductivity at the same H3Cit⋅3MEA content. The component composition of Na3Cit, H3Cit⋅3MEA and kH3Cit⋅3PEPA aqueous solutions was calculated. The probability of the existence of negatively charged ion-molecular complexes in H3Cit⋅3MEA and kH3Cit⋅3PEPA aqueous solutions is shown. The concentration and temperature dependence of citrate ions hydrolysis constant was obtained. The concentration and temperature dependence of these complexes was assessed. The atypical negative effect of heating on H3Cit⋅3MEA aqueous solutions molar electrical conductivity is associated with a change in the radius of the ion-molecular complex and its stability. The value of the limiting molar electrical conductivity of sodium, monoethanolammonium and polyethylenepolyammonium citrates aqueous solutions in the range of 293–313 K was estimated. Correlations were revealed between the values of the limiting electrical conductivity and ion-molecular complexes formation constants in H3Cit⋅PEPA aqueous solutions. The values of energy, enthalpy and entropy of activation of molar electrical conductivities of aqueous solutions were calculated. For the solutions studied, compensation effects were noted in the activation parameters of molar electrical conductivity.

Research on COD parameter in water based on the combination of UV absorption photometry and laser spectroscopy

Chemical Oxygen Demand (COD) is widely utilized as a representative and required measurement indicator of water pollution as well as water quality monitoring. The spectral technology is an important development direction in water quality detection. In this paper, a novel COD monitoring instrument is designed based on ultraviolet (UV) absorption photometry and laser spectroscopy. The instrument consists of CODcr and CODmn detection modules. The CODcr module is based on the Lambert-Beer law to measure UV absorption of organic matter in water, which can be used to measure the COD parameter in high concentration organic pollution in water. The CODmn module is based on the ratio method of fluorescence and Raman to analyze the spectral signals generated by the laser-excited water body, which can determine the COD parameter in low contaminated water. By analyzing the CODcr and CODmn parameters together, the comprehensive evaluation of organic pollutants in water can be realized. In the experiment, the CODcr and CODmn modules are respectively calibrated with the potassium hydrogen phthalate (KHP) solution as well as the mixed solution of humic acid sodium and glucose. Then the stabilities of the two detection modules are tested, and the detected result drifts are stable within six days. In addition, to verify the reliability of measuring results in complex environments, we test the instruments at 10 monitoring sites of the Sow River in Weihai city. The results of on-site monitoring are highly consistent with those of national standard method. The study result shows that the instrument developed in this paper can measure both CODcr and CODmn simultaneously, which can expand the COD detection range, and provide a new method for the comprehensive detection of organic pollutants in water.

Characteristics of soy films as affected by transglutaminase cross-linking and inclusions of pectin and protein enhancers.

Previously, we showed that water extract (soymilk, except pH was increased to 8 from 6.5) of whole soybean could be used directly as a raw material for producing edible soy films by deposition of the film-forming solution (soy extract with enhancers). However, the strength of such soy films needed improvement because they were weak. The purpose of this study was to investigate how transglutaminase (TG) cross-linking reactions and film enhancers, including pectin (low- and high-methoxyl pectin), whey protein isolate (WPI), and soy protein isolate (SPI), improve the physical properties of soy films. Soy films prepared with TG had tensile strength (TS) of 3.01MPa and puncture strength (PS) of 0.78MPa, which were higher by as much as 51% and 30% than that of soy films without TG treatment, respectively. Pectin showed significant effects on the mechanical properties of TG-added soy films in terms of TS, PS, and % elongation. On the other hand, only TS and PS were increased by the addition of WPI or SPI. Heat curing had a significant effect on soy film's physical properties. TG treatment significantly reduced film solubility when soaked in water and various levels of acid (vinegar) and base (baking soda) solutions. Under the experimental conditions of 35 unit TG and 28min of reaction, the degrees of cross-linking were evidenced by the disappearance of individual protein subunits, except the basic subunit of glycinin, and the reduction of 21% of lysine residues of the proteins. HIGHLIGHTS: Edible soy films were made with transglutaminase and about 21% lysine cross-linked. The mechanical strength of soy films was increased by incorporating film enhancers. Transglutaminase enhanced the mechanical properties of soy films.

Ameliorated Effects of Fucoidan on Dextran Sulfate Sodium-Induced Ulcerative Colitis and Accompanying Anxiety and Depressive Behaviors in Aged C57BL/6 Mice.

Fucoidan has shown better effects on the improvement of acute ulcerative colitis (UC). However, the specific mechanisms by which fucoidan improves UC-related behavioral disorders in aged mice, especially its effect on the gut-brain axis, remain to be further explored. C57BL/6 male mice aged 8 months were gavaged with 400 or 100 mg/kg bw day fucoidan for five consecutive weeks, with UC being induced by ad libitum to dextran sulfate sodium (DSS) solution in the fifth week. The results showed that fucoidan ameliorated UC and accompanying anxiety- and depressive-like behaviors with downregulated expressions of (NOD)-like receptor family and pyrin domain-containing 3 (NLRP3), apoptosis-associated speck-like protein (ASC), cysteine aspartate-specific protease-1 (Caspase-1) and interlekin-1β (IL-1β), and elevated mRNA levels of brain-derived neurotrophic factor (Bdnf) and postsynaptic-density protein 95 (Psd-95) in cortex and hippocampus. Furthermore, fucoidan improved the permeability of intestinal barrier and blood-brain barrier and restored the abnormal structure of the gut microbiota with a significantly decreased ratio of Firmicutes to Bacteroidota (F/B) and obviously increased abundance of Akkermansia. As a diet-derived bioactive ingredient, fucoidan might be a better alternative for the prevention of UC and accompanying anxiety- and depressive-like behaviors.