Solid Particles Research Articles

Radar-based measurement of solids back-mixing in the freeboard of a circulating fluidized bed

This work investigates solids back-mixing in the freeboard of a circulating fluidized bed based on THz-radar measurements of the concentrations and velocity distributions of the solid particles along the height of the riser. These data allow height-resolved closure of the solids mass balance and, thereby, quantification and further insight of the two main mechanisms for the back-mixing of the solids entrained from the bottom region of the fluidized bed: (i) solids disengagement and backmixing within the core region of the riser cross-section,; and (ii) solids lateral transfer of from the core region to the wall layers. The experiments were carried out in a circulating fluidized bed riser (3.1 m in height and 0.45 m2 in cross-section), which was operated with Geldart B solids fluidized with air at room temperature and for different gas velocities. The experimentally-derived data are expressed in terms of the disengagement rate and a lateral core-to-wall layer mass transfer coefficient. From the results, it is estimated that the presence of disengagement-based solids back-mixing is significant all along the 3-m riser. The disengagement rate shows a non-linear dependency on the solids concentration, with the lateral solids transfer to the walls (which follows a linear dependency on the solids concentration) eventually becoming the dominant form of back-mixing at upper heights.

Enhanced solid particle erosion resistance of nanocrystalline Ni-W coatings through multilayer approach

Electrodeposited nanocrystalline Ni-W alloy coatings are projected as potential alternatives for hard chrome (HCr) coatings owing to their comparable hardness and superior corrosion resistance. However, the limited strain hardening ability of the nanocrystalline Ni-W coatings manifests in their poor resistance towards solid particle erosion involving a high strain-rate (>103 s−1) deformation. In the present study, a novel microstructural engineering strategy has been implemented to enhance the strain hardening ability of the nanocrystalline Ni-W coatings without compromising on their strength/hardness. Ni-W multilayer coatings composed of alternatively stacked soft (2.6 GPa) and hard (8.5 GPa) Ni-W layers were developed using the pulse reverse electrodeposition technique. Further, to investigate the effect of individual layer thickness (λ), multilayer coatings with different λ were deposited. Solid particle erosion testing using the angular SiO2 particles showed that the multilayer coatings (irrespective of λ) exhibit superior erosion resistance compared to the homogeneous nanocrystalline Ni-15W at both oblique (θ = 30°) and normal (θ = 90°) impact conditions. The post-erosion microstructural analysis of the multilayer coatings revealed that the hard Ni-W layers undergo uniform strain (ε > 50 %) without cracking due to the constrained co-deformation imposed by the surrounding soft Ni-W layers. Therefore, the enhanced erosion resistance of the multilayer coatings is attributed to the effective dissipation of impact energy through co-deformation of the individual hard and soft Ni-W layers.

Modeling of the dissolution phenomena of solid particles into an infinitely large medium from the analytical solutions of reaction–diffusion equations

Mathematical solutions of the concentration of dissolved component in surrounding fluid were obtained for analyses of the dissolution phenomena of spherical, cylindrical, and slab-type particles. Calculation of the surface flux enabled material balance equations to be derived for the prediction of transient particle size. For the spherical particle, the resulting differential equation was solved numerically to compare with the analytical solution. For the cylindrical particle, the Weber transform was applied to predict the radius of the infinitely long cylinder as a function of time. After obtaining an analytical solution for the thickness of the dissolving slab, the result was compared with those of the sphere and cylinder. The spherical particle exhibited the shortest complete dissolution time (CDT), due to having the greatest surface-to-volume ratio. When external film resistance was important for the mass transfer, the Biot number was included in the governing equation, and to predict the particle size during dissolution, the concentration in the fluid phase could be derived by the combination of variables, or the Weber-type transform. When first-order or zero-order reaction occurs in the surrounding fluid, the concentration could also be predicted by the Laplace transform, and the particle size could be calculated for the solid particles. Similar to the simple diffusion process, CDT was predicted to increase in the order sphere < cylinder < slab. The experimental data of the dissolution of polymeric fiber was compared with the modeling result to estimate the diffusivity and solubility factor, which varied with the pH of the surrounding fluid.

Annual review of capillary electrophoresis technology in 2023

This paper serves as an annual review of capillary electrophoresis (CE) technology for 2023. The journals were selected based on their impact factor (IF), a universally recognized academic performance metric, combined with experimental work closely related to CE technology, to facilitate the rapid acquisition of significant research and application advancements in CE technology in 2023. A thematic search of the ISI Web of Science database yielded 669 research papers on CE technology published in 2023. This review highlights five experimental papers published in journals with IFs greater than 10.0, including Nature Communications, Nucleic Acids Research, Engineering, Journal of Medical Virology, and Carbohydrate Polymers, and 31 experimental papers from representative journals with IFs between 5.0 and 10.0, such as Analytical Chemistry, Analytica Chimica Acta, Talanta, and Food Chemistry. It also provides an overview of experimental research in journals with focused reporting on CE technology but with IFs less than 5.0, such as Journal of Chromatography A and Electrophoresis, as well as significant experimental research from key domestic Chinese core journals (Peking University). In 2023, all the latest scientific advancements reported in journals with an IF greater than 10.0 utilized previously reported CE methods, offering new breakthroughs for the promotion and application of CE technology. Additionally, new applications of CE in conjunction with mass spectrometry remained a hot topic. An increase in reports on the hardware aspects of CE, such as 3D printing and underwater systems, and significant breakthroughs in the analysis of non-solution samples, such as solid particles, cell vesicles, cells, viruses, and bacteria, was noted. CE is advantageous for the analysis of drugs and their components. In Chinese journals, the number of papers on CE applications exceeded that in previous years, with particular focus on the field of printing for new applications.

Pickering emulsions stabilized by β-Lactoglobulin-Rosmarinic acid-Pectin nanoparticles: Influence of interfacial behavior and rheology performance

Grafting polyphenols and glycosylation are effective means to enhance the wettability and emulsifying properties of natural protein particles. A stable pickering emulsion (PE) with antioxidant properties was prepared using β-Lactoglobulin-Rosmarinic acid-Pectin (β-LG-RA-PC) conjugates as stabilizers in this study. When PC and β-LG-RA with the same mass were covalently combined, the solid protein-based particles exhibited ideal wettability (84.2 ± 0.3°), emulsification performance, and molecular flexibility. PEs with an oil content of 66.7% were successfully prepared using a 10 mg/mL concentration of the complex. The intrinsic reasons for the stabilization of the PE were explored through interfacial tension (from 16.02 mN/m to 12.18 mN/m), adsorption kinetics, interfacial expansion viscoelastic modulus (the tangent of the phase angle was 0.22), microstructure, and rheological properties, revealing that the dense, ideally viscoelastic interface layer formed was the main factor. The electrostatic repulsion between droplets, and the formation of a robust spatial network structure, facilitated PEs’ stability. These studies confirmed the possibility of implementing protein-based particles to yield food-grade PE.

PEMODELAN KUALITAS AIR TANAH OLEH AIR LIMBAH DOMESTIK MENGGUNAKAN ARCGIS DI DESA KERTALANGU

&lt;p&gt;&lt;em&gt;The community living in Kesiman Kertalangu Village, East Denpasar, Denpasar City, Bali, has a few open shallow wells at home. Well water is used for daily activities such as washing, washing vehicles, and watering plants. The main source of water is groundwater, which is found in rocks below the earth's surface. The availability and movement of groundwater depends on the geological conditions of the area.&lt;/em&gt;&lt;em&gt; &lt;/em&gt;&lt;em&gt;Groundwater that is used as a source of community life must meet good water quality, so the purpose of this study was to determine the condition of groundwater during the study. The samples used for groundwater testing were 30 wells spread across this village. The methods used were interviews with the local community, field testing of well water samples (smell and temperature tests), laboratory tests (pH, TSS, TDS, DHL and microbiology) and modeling analysis of all research data results using the ARCGIS application. The research results obtained were field tests such as odor tests and temperature tests that passed the clean water requirements because they met the standards set by the Ministry of Health. laboratory tests such as the TDS, TSS and DHL tests have met the requirements as clean water because the number of solid particles dissolved in water and gas is below the specified limits, and the amount of suspended solids in water is also below the limits. Microbiological test results showed that several points were quite polluted by E.Coli and Total Coliform bacteria caused by the distance between the well points and the septic tank in people's homes.&lt;/em&gt;&lt;/p&gt;

Nanoframes as a Resilient Candidate for a Broader Spectra of Catalysis Challenges

Metal nanoframes have gained tremendous attention in the domain of modern research and development due to their distinctive 3D spatial structure, efficient physiochemical properties, and comparatively good activity. Different strategies have been implicated by the researchers to design nanoframes of varying chemical natures and shapes. Most of the synthetic protocols being adopted to design nanoframes consist of two main steps: nucleation and the growth of solid particles and, secondly, excavation of the interiors. In this context, many synthetic methods are overviewed. To show their unprecedented performance or activity, a few applications in catalysis, biomedicine, theranostics, SERS, the sensing of different materials, the reduction of CO2, etc., are also discussed.

Preparation of geopolymers from thermally activated lithium slag: Activity enhancement and microstructure

As an industrial by-product of the lithium extraction process from spodumene, lithium slag (LS) is less reactive, rendering it a chemically infeasible binder. In this study, a thermal activation approach was employed to enhance the reactivity of LS. The underlying mechanisms of LS's thermal activation at various temperatures were thoroughly explored through XRD and ICP. The results indicated that alterations in the aluminosilicate composition of LS occurred during calcination between 500 °C and 900 °C, leading to the transformation of spodumene into amorphous forms. Particularly noteworthy was the initial increase in the LS amorphous phase content with increasing temperature, followed by a subsequent decline. Building upon these findings, a lithium slag geopolymer (LSG) was prepared via alkali activation, using the activated LS as the exclusive precursor. It was observed that elevating the content of active components in LS enhanced the geopolymerization reactions, resulting in an improved mechanical strength of LSG. Remarkably, after 28 days of aging, geopolymer specimens prepared from LS calcined at 700 °C exhibited a compressive strength of 36.0 MPa. Combining these results with FTIR and SEM-EDS analyses, it becomes evident that suitable calcination temperatures empower LS to release a higher quantity of silicon and aluminum ions. These ions play a significant role in the geopolymerization process, leading to the formation of an amorphous sodium (calcium) aluminosilicate hydrate (N(C)-A-S-H) gel. This gel acts as a binder, tightly binding the residual solid particles, and thus forming a denser microstructure.

Randomised nano-/micro- impact testing – A novel experimental test method to simulate erosive damage caused by solid particle impacts

A novel randomised nano-/micro-scale impact test method has been developed to experimentally simulate particulate erosion where statistically distributed impacts with defined energy occur sequentially within the test area. Tests have been performed on two brittle glasses (fused silica and BK7) to easily highlight the interaction between impacts, as well as on two ceramic thermal barrier coating systems (TBCs, yttria stabilised zirconia, 7YSZ, and gadolinium zirconate, GZO) that experience erosion in service. Differences in erosion resistance were reproduced in the randomised impact tests, with GZO less impact resistant than 7YSZ, and BK7 significantly worse than fused silica. The impact data show that erosion resistance is influenced by different factors for the glasses (crack morphology, longer-length interaction of radial-lateral cracks in BK7 vs cone-cracking in fused silica) and TBCs (fracture toughness).

Direct numerical simulation of three-dimensional particle-laden thermal convection using the Lattice Boltzmann Method

In thermal multiphase flows, the modulation in the heat transfer rate due to the presence of finite-size solid particles attract growing interest in recent years. This study focuses on developing a robust and efficient simulation method for particle-laden Rayleigh-Bénard convection. The present work utilizes the double distribution function-based thermal lattice-Boltzmann method (TLBM), which enables successful simulations of multiphase fluid-thermal interactions. The no-slip boundary of the moving solid particles is handled by the interpolated bounce-back scheme. Additionally, Galilean invariant momentum exchange and heat exchange approaches are employed for hydrodynamic force and heat transfer calculation at the solid boundaries. The accuracy of the current method is verified with several benchmark cases, including three-dimensional single-phase Rayleigh-Bénard convection, as well as the settling of hot and cold spherical particles in a three-dimensional enclosure. Furthermore, we explore the modulation of Rayleigh-Bénard flows due to the presence of freely moving finite-size particles. The simulations are conducted on a distributed memory cluster with a 3D domain decomposition technique facilitated by the MPI library. A brief discussion on the parallel performance of the simulations is provided for both particle-laden and single-phase flow scenarios. Finally, the effects of finite-size solid particles on the overall heat transfer efficiency and modulation to the flow field in three-dimensional particle-laden turbulent Rayleigh-Bénard convection are discussed. The results show that addition of solid particles results in a moderate increase in the overall Nusselt number, and this enhancement is mainly due to the increased heat flux transported by the particles.

Recent advances in electrostatic precipitation of particles from flue gases generated by domestic heating appliances. A brief outlook

Winter season is the time of increased emission of exhaust gases from household heating appliances containing particulate matter (PM) and other noxious contaminants. Many old buildings and single houses, particularly at rural and small town regions, still use stoves, fireplaces or ovens to flat heating. Besides qualified fuels like coal or biomass pellets, all kinds of wastes are also burned in many cases, producing not only mineral particles but also toxic volatile organic compounds or other carcinogenic species. To solve the problem of high level of emission of solid particles and organic-compound molecules different constructions of electrostatic precipitators, which can remove such particles, have been developed in last two decades, which were designed to operate downstream of small domestic boilers. Such electrostatic precipitator must comply with the ECODESIGN emission limits, which set the emission level at 20 mg/m3, for biomass. The mass collection efficiency should be higher than 95 % to obtain this emission level. This brief review presents different constructions of electrostatic precipitators designed to be used for the removal of fly ash particles from domestic heating appliances.

Analysis of the amount and structure of solid particles PM released into the city’s atmospheric air by motor transport

Atmospheric air pollution with fine particles PM2.5 and PM10 is one of the main environmental problems of the city. This paper presents the results of the study of quantitative and structural components of solid particles’ emissions in the city of Almaty, released during the operation of cars: by an engine with exhaust gases, by tire abrasion, by braking devices (linings) and road pavement wear. РM solid particles in the amount of 543.2 tons are released annually into the atmospheric air of Almaty by motor transport. The bulk PM10 is released totally from the tires, brakes and road – 65.4 %, from the engine – 34.6 %. On diesel buses and trucks, the bulk РM particles’ emissions are released from the exhaust gas engines. Recommendations are given to reduce PM particles emitted by motor transport.

Numerical simulations of CO2 absorption by MgO-based sorbent in a gas–solid fluidized bed

Given that carbon dioxide (CO2) constitutes the predominant proportion of greenhouse gas emissions, its capture, utilization and storage have always been a subject of great concern. Gas-solid fluidized bed has become one of the commonly applied equipment for the removal of CO2 from flue gases owing to its advantages such as exceptional mixing effect and substantial interfacial area between the phases. However, there is a lack of attention to the mechanism of CO2 absorption by individually-tracked moving solid sorbents as well as their effects on the decarbonization performance in a gas–solid fluidized bed. In this study, CO2 removal model by solid particles based on MgO adsorbent was established with the implementation of the shrinking-core model and each particle was tracked individually. Results validated the accuracy of the absorption model and revealed that smaller sizes of the solid absorbent, lower inlet gas velocities and larger inlet CO2 mass fractions exhibit relatively high CO2 removal efficiency. In addition, the decarbonization performance of fluidized and packed beds was compared. The packed bed exhibits more uniform gas flow and higher CO2 removal efficiency, whereas the fluidized bed provides larger interphase contact area, which facilitates the heat transfer process. Through the analysis of a series of parameters, the results provide recommendations for improving the CO2 removal efficiency and help to explore the optimal protocol for the design of bed reactors for CO2 removal.

Fractionation of edible fats—Separation of fat‐covered particles by decanter centrifuge

AbstractThis work investigates the feasibility of using a decanter centrifuge to separate solid particles coated with a high melting fat from a liquid oil. The process involves feeding cold silica particles into a melt, upon which the hardstock fat crystallizes, and the particles are subsequently separated using a decanter centrifuge. Being the first attempt for such a design, only the separation step is studied, and a model system is used. It comprised canola oil (CO), fully hydrogenated rapeseed oil a priori crystallized on silica gel particles. Different particle sizes and accelerations of gravity were studied. To measure the success of this separation process, the data from light microscopy, and differential scanning calorimetry of the feed, oleins, and stearins were used. The findings show that the separation of the fatty particles used in this work, and liquid oil in decanter centrifuges is feasible while future research should focus on the crystallization part of the process. The model developed to describe the oil‐holding capacity of the cake focuses on the capillary liquid entrapped in the spaces between the particles and sufficiently represents the experimental findings which show that separation efficiencies increase with increasing centrifugal acceleration.Practical Applications: This work introduces an alternative fat fractionation process by separating a model system of CO, FHRO, and solid entrainers through a decanter centrifuge. The results can be potentially used for the development of a fully continuous dry fractionation process, which can achieve in one step higher SE than the conventional ones and can be tripalmitate‐selective.

Investigating the Effect of Palm Kernel Shell Powder on the Rheological and Filtration Properties of Water Based Mud

During drilling operations, the use of drilling fluid plays a critical role, and over time, there has been considerable interest in enhancing drilling fluid characteristics in order to improve performance, reduce costs, and prevent environmental pollution. Deviating from conventional additives, recent studies have explored the use of alternative materials, as drilling fluid additives. In line with this trend, this study focuses on the laboratory investigation of the rheological and filtration properties of water-based drilling fluid treated with Palm Kernel Shell Powder (PKSP) with high viscosity polyanionic cellulose (PAC HV), used as control. To assess the impact of PKSP in water-based mud, experiments were carried out using concentrations spanning from 0.5g to 2.5g, temperatures of 27°C, 40°C, 60°C, and 80°C, and aging of 24, 48, and 72 hours. From the results the plastic viscosity of mud samples treated with PKSP were temperature dependent and also with increasing aging. The addition of PKSP showed improved performance in terms of reducing the filtrate volume as well as the cake thickness with increasing concentration of the additives, and the concentration that gave the best results across all aging duration was 2.5g. The mud weight and pH of all samples remained relatively constant, with no significant changes observed. However, PAC HV showed better results in all the cases of fluid loss and mud cake thickness. It could be attributed to the soluble contents in the PAC HV which increased the viscosity significantly and thus, kept the solid particles in suspension.

Trajectory dynamics of particles in accelerated toroidal pipe: A computational study using CFD-DPM simulations

In this study, we investigate the behavior of solid particles of varying sizes within an accelerated toroidal filled with fluid using computational fluid dynamics- discrete phase model (CFD-DPM) simulations. A comprehensive grid independence study and validation were conducted to ensure the accuracy of our simulations. We focus on particles with 10-, 50-, and 100-microns diameters. Our simulations indicate that the primary flow (relative tangential velocity) of both the fluid and the particles follow the input acceleration. We also examined the secondary flow within the toroidal. Smaller particles (10 microns) closely follow the fluid flow with minimal lag, while larger particles (50 and 100 microns) exhibit a noticeable lag due to the inertia effect. Furthermore, the displacement from the initial position is also dependent on the particle size, with smaller particles traveling further distances. However, despite the ongoing acceleration of the fluid and the toroidal, the largest particles (100 microns) eventually settle and stop due to their high inertia (mass), and their velocity begins to decrease during the acceleration of the toroidal. These findings highlight the significant role of particle size in determining particle behavior within a toroidal, paving the way for future research and Particle Imaging Velocimetry Gyroscope (PIVG) application.

Analysis of the solid breakdown characteristics under high voltage pulse

As an efficient breakage technology, high voltage pulse breakage technology (HVP) has been an attractive topic due to its selective advantages. Typically, HVP is conducted in water and it is believed that the breakdown strength of water is higher than that of solids, and the discharge channel will be formed in solids under short voltage front rise time. The location of the discharge channel is important for understanding and optimizing of HVP. The study focuses on solid breakdown and the location of the discharge channel. The breakdown type during the HVP process is analyzed, the breakage characteristics of solid particles are investigated, the breakdown parameters are compared between water and solid, and the influence of solid composition on breakdown type is revealed. Under the settled conditions of this study, the results showed that: the discharge channel is easier to be formed inside the solid particle with the particle in contact with the electrode. And the discharge channel is formed in water with water gap between the solid and the electrode. The location of the discharge channel is affected by solid composition and the electrical breakdown probability can be improved with other compositions embedded in solid particles.

The effect of solid nitrogen on nucleate boiling heat transfer in a slush nitrogen pool

The nucleate boiling heat transfer in a slush nitrogen pool has been studied across a heat-flux range from 5 to 400 kW/m2 and a system pressure range from 12.5 kPa (triple point pressure) to 101 kPa (atmospheric pressure). The effect of solid nitrogen on the heat transfer process was found to vary with the heat flux and the pressure. Experimental results reveal that the nucleate boiling heat transfer coefficient (HTC) of slush nitrogen is higher than that of subcooled liquid nitrogen at the low heat flux, which can be attributed to the fact that the solid nitrogen particles (with their latent heat of melting) absorb heat in the thermal boundary layer and form a sharper temperature gradient near the boiling surface. However, at the high heat flux, the HTC of slush nitrogen is lower than that of subcooled liquid nitrogen, which can be attributed to the invasion and inhibition occurring between the solid nitrogen particles and the bubbles during boiling, leading to the accumulation of vapor phase with low thermal conductivity on the boiling surface, thereby the heat transfer will be suppressed. As a result, a dual effect for the nucleate boiling heat transfer in slush nitrogen can be observed. Furthermore, the critical heat flux (CHF) of slush nitrogen is obtained and compared with the CHF of subcooled liquid nitrogen. According to the CHF model, the bubble period is the dominant parameter in determining the CHF. A calibrated CHF correlation for slush nitrogen is developed based on the hypothesis that the bubble period is prolonged as the effective viscosity of slush nitrogen increases with the solid volume fraction. The CHF values of slush nitrogen with the solid volume fraction of 10%, 20% and 30% are 0.96, 0.91 and 0.84 times those of subcooled liquid nitrogen, respectively, at the pressures higher than 50 kPa. Consequently, the solid volume fraction of slush nitrogen and the degree of subcooling of subcooled liquid nitrogen are found to have opposite effects on CHF.

Development of potassium doped tungsten plate for fusion reactor applications

Since fusion reactors including DEMO and beyond are expected to be operated for a longer period of time than ITER, plasma-facing materials (PFM) will suffer by longer term heat load and non-negligible neutron irradiation damage. Therefore, for tungsten (W) materials as PFM, improvement of low temperature brittleness and suppression of recrystallization embrittlement and neutron irradiation embrittlement are required. To address these issues, various modified W materials have been developed by applying alloying with solid solution elements and second-phase dispersion techniques such as solid particles and bubbles. As a result, potassium-doped W (K-doped W), in which K bubbles are dispersed, was found to be effective for all of the above issues. However, the materials used in these evaluations were relatively small and not large enough to fabricate, for example, ITER divertor monoblocks (12 mm thick). In the present study, K-doped W plate with a sufficient thickness (more than 12 mm) for application to fusion reactor components like divertor monoblocks were developed and the fundamental properties were evaluated.

Construction of coal pitch-based HA-K grafted poly condensates and their excellent anti-temperature and viscosity-reducing properties

Humic acids (HAs) are widely used as filtrate and viscosity reducers in drilling fluids. However, their practical utility is limited due to poor stability in salt resistance and high-temperature resistance. High-temperature coal pitch (CP) is a by-product from coal pyrolysis above 650 °C. The substance's molecular structure is characterized by a dense arrangement of aromatic hydrocarbon and alkyl substituents. This unique structure gives it unique chemical properties and excellent drilling performance, surpassing traditional humic acids in drilling operations. Potassium humate is prepared from CP (CP-HA-K) by thermal catalysis. A new type of high-quality humic acid temperature-resistant viscosity-reducer (Graft CP-HA-K polymer) is synthesized with CP-HA-K, hydrolyzed polyacrylonitrile sodium salt (Na-HPAN), urea, formaldehyde, phenol and acrylamide (AAM) as raw materials. The experimental results demonstrate that the most favorable conditions for the catalytic preparation of CP-HA-K are 1 wt% catalyst dosage, 30 wt% KOH dosage, a reaction temperature of 250 °C, and a reaction time of 2 h, resulting in a maximum yield of CP-HA-K of 39.58%. The temperature resistance of the Graft CP-HA-K polymer is measured to be 177.39 °C, which is 55.39 °C higher than that of commercial HA-K. This is due to the abundant presence of amide, hydroxyl, and amine functional groups in the Graft CP-HA-K polymer, which increase the length of the carbon chains, enhance the electrostatic repulsion on the surface of solid particles. After being aged to 120 °C for a specified duration, the Graft CP-HA-K polymer demonstrates significantly higher viscosity reduction (42.12%) compared to commercial HA-K (C-HA-K). Furthermore, the Graft CP-HA-K polymer can tolerate a high salt concentration of 8000 mg·L−1, measured after the addition of optimum amount of 3 wt% Graft CP-HA-K polymer. The action mechanism of Graft CP-HA-K polymer on high-temperature drilling fluid is that the Graft CP-HA-K polymer can increase the repulsive force between solid particles and disrupt bentonite's reticulation structure. Overall, this research provides novelty insights into the synthesis of artificial humic acid materials and the development of temperature-resistant viscosity reducers, offering a new avenue for the utilization of CP resources.