Solid Electrolyte Interphase Research Articles

Probing Surface Dynamics of SiOx Thin-Film Electrodes during Cycling through X-Ray Photoemission Spectroscopy and Operando X-Ray Reflectivity.

SiOx electrodes are promising for high-energy-density lithium-ion batteries (LIBs) due to their ability to mitigate volume expansion-induced degradation. Here, we investigate the surface dynamics of SiOx thin-film electrodes cycled in different carbonate-based electrolytes using a combination of ex situ X-ray photoelectron spectroscopy (XPS) and operando synchrotron X-ray reflectivity analyses. The thin-film geometry allows us to probe the depth-dependent chemical composition and electron density from surface to current collector through the solid electrolyte interphase (SEI), the active material, and the thickness evolution during cycling. Results reveal that SiOx lithiation initiates below 0.4 V vs Li+/Li and indicate a close relationship between SEI formation and SiOx electrode lithiation, likely due to the high resistivity of SiOx. We find similar chemical compositions for the SEI in FEC-containing and FEC-free electrolytes but observe a reduced thickness in the former case. In both cases, the SEI thickness decreases during delithiation due to the removal or dissolution of some carbonate species. These findings give insights into the (de)lithiation of SiOx, in particular, during the formation stage, and the effect of the presence of FEC in the electrolyte on the evolution of the SEI during cycling.

Bimetal Fluorides with Adjustable Vacancy Concentration Reinforcing Ion Transport in Poly(ethylene oxide) Electrolyte.

The poor ambient ionic transport properties of poly(ethylene oxide) (PEO)-based SPEs can be greatly improved through filler introduction. Metal fluorides are effective in promoting the dissociation of lithium salts via the establishment of the Li-F bond. However, too strong Li-F interaction would impair the fast migration of lithium ions. Herein, magnesium aluminum fluoride (MAF) fillers are developed. Experimental and simulation results reveal that the Li-F bond strength could be readily altered by changing fluorine vacancy (VF) concentration in the MAF, and lithium salt anions can also be well immobilized, which realizes a balance between the dissociation degree of lithium salts and fast transport of lithium ions. Consequently, the Li symmetric cells cycle stably for more than 1400 h at 0.1 mA cm-2 with a LiF/Li3N-rich solid electrolyte interphase (SEI). The SPE exhibits a high ionic conductivity (0.5 mS cm-1) and large lithium-ion transference number (0.4), as well as high mechanical strength owing to the hydrogen bonding between MAF and PEO. The corresponding Li//LiFePO4 cells deliver a high discharge capacity of 160.1 mAh g-1 at 1 C and excellent cycling stability with 100.2 mAh g-1 retaining after 1000 cycles. The as-assembled pouch cells show excellent electrochemical stability even at rigorous conditions, demonstrating high safety and practicability.

Promoting Cathodic Kinetics and Anodic Stability in Practical Room-Temperature Sodium-Sulfur Batteries with Bifunctional Electrolytes.

The development of room-temperature (RT) sodium-sulfur (Na-S) batteries is severely hindered due to the slow kinetics of the S cathode and the instability of the Na-metal anode. To overcome this, we introduced a dual-functional electrolyte cosolvent, trifluoromethanesulfonamide (TFMSA). Short-chain Na2Sx (1 ≤ x ≤ 2) can be effectively dissolved due to the strong H-S bond interaction between TFMSA and sulfides, which changes the S conversion process, thereby effectively enhancing the conversion kinetics of the cathode. Meanwhile, TFMSA can generate a stable solid electrolyte interphase on the Na-metal surface to protect it from soluble polysulfide attack. Therefore, the RT Na-S batteries using the ether electrolyte show a high initial discharge capacity of 896.6 mAh g-1 and a capacity retention rate of 73% after 150 cycles at 0.2C, and the pouch cell also demonstrates its practical performance. This work proposes a dual-functional electrolyte cosolvent selection principle to inspire the practical application of high-performance RT Na-S batteries.

Uniform carbon coating and solid electrolyte interphase synergistically enhanced exceptional anodic K‐ion storage properties of stable KTiOPO4 single crystals

AbstractSearching for low‐cost, high‐capacity, high‐power, high‐stability, high‐tap‐density, and inherently safe materials for developing cheap, safe, and high‐performance batteries has always been a research hotspot. Herein, an inherently safe, low‐cost, and low‐strain KTiOPO4 (KTOP) submicron single crystals with a uniform thin layer carbon coating are developed using a ball‐mill assisted solid‐state method. Uniform solid electrolyte interphase, carbon coating, and inherently stable structure synergistically help compact KTOP submicron single crystals achieve an exceptional anodic K‐ion storage performance. The carbon‐coated KTOP single crystals obtained under the carbonization temperature of 400°C (KTOP‐C‐400) can deliver an exceptional potassium ion storage performance of 253.3, 224.0, 175.5, and 131.1 mA h g−1 at the current density of 100, 200, 500, and 1000 mA g−1, respectively, in the electrolyte of 5 M potassium bis(fluorosulfonyl)imide (KFSI) in DIGLYME electrolytes. Even after being cycled at 1000 mA g−1 for 1000 cycles, the capacity was maintained at 182.5 mA h g−1 with a coulombic efficiency of 99.9%.

Unravelling the anionic stability of an ether-based electrolyte with a hard carbon or metallic sodium anode for high-performance sodium-ion batteries

In hard carbon (HC) anodes, elucidating the relationship between the solid electrolyte interphase formation and the solvated Na+ co-intercalation mechanism is crucial, particularly considering different anionic salts in ether-based electrolytes. Here, we comprehensively explore the impact of different anionic salts on the electrochemical performance of HC/Na half-cell and elucidate the underlying mechanism through experimental studies and theoretical calculations. The surface morphology of the HC anode and its interphasial property are further investigated to evaluate the differences endowed by the presence of various anionic salts in diglyme (2G). The HC/Na half-cells with NaPF6-2G and sodium trifluoromethanesulfonate (NaCF3SO3)-2G display superior electrochemical performance with faster kinetics and lower interfacial resistance than those with NaClO4-2G, sodium bis-(fluorosulfonyl) imide (NaFSI)-2G and sodium bis-(trifluoromethanesulfonyl) imide (NaTFSI)-2G. NaClO4-2G forms a relatively thick interphase layer with high resistance at the electrode/electrolyte interface owing to its insufficient stability. NaFSI-2G and NaTFSI-2G exhibit severe side reactions with Na metal, producing a thick interphase layer on the HC surface with high interfacial resistance from excess electrolyte decomposition, thus deteriorating the electrochemical performance. In summary, the study on the stability of different anionic salts in ether-based electrolyte for the HC anode with the intercalation mechanism provides valuable insights for screening appropriate conductive salts for high-performance sodium-ion batteries, especially when considering Na metal counter/reference electrodes.

SnF2-Catalyzed Lithiophilic-Lithiophobic Gradient Interface for High-Rate PEO-Based All-Solid-State Batteries.

Polyethylene oxide (PEO)-based all-solid-state lithium metal batteries (ASSLMBs) are strongly hindered by the fast dendrite growth at the Li metal/electrolyte interface, especially under large rates. The above issue stems from the suboptimal interfacial chemistry and poor Li+ transport kinetics during cycling. Herein, a SnF2-catalyzed lithiophilic-lithiophobic gradient solid electrolyte interphase (SCG-SEI) of LixSny/LiF-Li2O is in situ formed. The superior ionic LiF-Li2O rich upper layer (17.1 nm) possesses high interfacial energy and fast Li+ diffusion channels, wherein lithiophilic LixSny alloy layer (8.4 nm) could highly reduce the nucleation overpotential with lower diffusion barrier and promote rapid electron transportation for reversible Li+ plating/stripping. Simultaneously, the insoluble SnF2-coordinated PEO promotes the rapid Li+ ion transport in the bulk phase. As a result, an over 46.7 and 3.5 times improvements for lifespan and critical current density of symmetrical cells are achieved, respectively. Furthermore, LiFePO4-based ASSLMBs deliver a recorded cycling performance at 5 C (over 1000 cycles with a capacity retention of 80.0 %). More importantly, impressive electrochemical performances and safety tests with LiNi0.8Mn0.1Co0.1O2 and pouch cell with LiFePO4, even under extreme conditions (i.e., 100 °C), are also demonstrated, reconfirmed the importance of lithiophilic-lithiophobic gradient interfacial chemistry in the design of high-rate ASSLMBs for safety applications.

SnF2‐Catalyzed Lithiophilic–Lithiophobic Gradient Interface for High‐Rate PEO‐Based All‐Solid‐State Batteries

AbstractPolyethylene oxide (PEO)‐based all‐solid‐state lithium metal batteries (ASSLMBs) are strongly hindered by the fast dendrite growth at the Li metal/electrolyte interface, especially under large rates. The above issue stems from the suboptimal interfacial chemistry and poor Li+ transport kinetics during cycling. Herein, a SnF2‐catalyzed lithiophilic‐lithiophobic gradient solid electrolyte interphase (SCG‐SEI) of LixSny/LiF‐Li2O is in situ formed. The superior ionic LiF‐Li2O rich upper layer (17.1 nm) possesses high interfacial energy and fast Li+ diffusion channels, wherein lithiophilic LixSny alloy layer (8.4 nm) could highly reduce the nucleation overpotential with lower diffusion barrier and promote rapid electron transportation for reversible Li+ plating/stripping. Simultaneously, the insoluble SnF2‐coordinated PEO promotes the rapid Li+ ion transport in the bulk phase. As a result, an over 46.7 and 3.5 times improvements for lifespan and critical current density of symmetrical cells are achieved, respectively. Furthermore, LiFePO4‐based ASSLMBs deliver a recorded cycling performance at 5 C (over 1000 cycles with a capacity retention of 80.0 %). More importantly, impressive electrochemical performances and safety tests with LiNi0.8Mn0.1Co0.1O2 and pouch cell with LiFePO4, even under extreme conditions (i.e., 100 °C), are also demonstrated, reconfirmed the importance of lithiophilic‐lithiophobic gradient interfacial chemistry in the design of high‐rate ASSLMBs for safety applications.

Assessment of “Inverse” Cross‐Talk (Anode to Cathode) in High‐Voltage Li/Mn‐Rich Layered Oxide || Li Cells

AbstractLi/Mn‐rich layered oxide (LMR) offers high practical discharge capacity originating from both cationic and anionic redox, but its operation is practically challenging as full capacity utilization at high cathode potentials (> 4.6 V vs Li|Li+) is intertwined with phase transformation, oxygen release, and transition metal dissolution. Dissolved TMs in particular, can deposit and damage the anode via a process known as electrode cross‐talk that decreases Li inventory due to Li plating. Given the excess in active lithium, Li‐metal anode (LMA) is frequently paired with LMR for a systematic cathode R&D, though is believed to cause inverse cross‐talk, i.e., diffusion of LMA degradation products from the solid electrolyte interphase (SEI) toward the cathode, triggering bulid‐up of resistive cathode electrolyte interphase (CEI). Indeed, a thicker, more organic‐based, and slightly resistive CEI is proven in Li‐ compared to “SEI‐poor” Li4Ti5O12 (LTO)‐based cells via X‐ray photoelectron spectroscopy, time‐of‐flight secondary ion mass spectrometry, and electrochemical techniques, which likely even decreases metal dissolution from LMR, though their practical impact on overpotential is shown to be less relevant. The capacity recovery after transferring cycled (“old”) LMR from Li cells to fresh Li cells rather points to other meaningful contributions to capacity fading than the inverse crosstalk.

Electrolyte Engineering with TFA- Anion-Rich Solvation Structure to Construct Highly Stable Zn2+/Na+ Dual-Salt Batteries.

Electrolyte engineering is recognized as an effective technique for high-performance aqueous zinc-ion rechargeable batteries, addressing difficulties such as free water decomposition, zinc anode corrosion, and zinc dendrite growth. Different from traditional strategies in aqueous electrolyte systems, this work focuses on organic electrolytes involving zinc trifluoroacetate hydrate (Zn(TFA)2·xH2O), sodium trifluoroacetate (NaTFA) dual-salt and acetonitrile (AN) solvent, in which trifluoroacetate anions (TFA- anions) have strong affinity toward zinc ions to form anion-rich solvates, thus inducing an inorganic-rich solid electrolyte interphase (SEI) to protect Zn from dendrite growth and side reactions. The Zn anode manifests long-term cycling over 2400h at a current density of 0.5mAcm-2 with a high Coulombic efficiency (CE) of 99.75%, showing an areal capacity as high as 5mAhcm-2. Owing to the high reversibility of the sodium ions intercalation/deintercalation process in Na2MnFe(CN)6, the Zn//Na2MnFe(CN)6 full cells with the dual-salt electrolyte perform much better in terms of capacity retention than a device with Zn(TFA)2/AN electrolyte. This approach may open a new avenue for efficient zinc-ion rechargeable batteries via developing organic electrolytes.

Rational design of epoxy functionalized ionic liquids electrolyte additive for hydrogen-free and dendrite-free aqueous zinc batteries

Despite the high safety and low cost associated with aqueous Zn-ion batteries (ZIBs), uncontrolled Zn dendrite growth and parasitic reactions induced by water significantly diminish their stability. Herein, a new epoxy functionalized ionic liquid, 4-methyl-4-glycidylmorpholin bis[(trifluoromethyl)sulfonyl]imide (MGM[TFSI]), has been developed to mitigate water reactivity for stable ZIBs. It was found that the MGM+ cation disrupts the hydrogen bond network of water, hindering its adsorption on Zn anodes, thereby suppressing water decomposition and enhancing anode stability. Additionally, preferential adsorption of MGM+ cations on the Zn anode surface mitigates tip effects, suppresses dendrite growth, and promotes the formation of a ZnF2 solid electrolyte interphase layer, effectively isolating the anode from the bulk electrolyte. As a result, benefiting from the well-designed MGM+-based electrolyte, Zn//Zn cells achieve significantly enhanced cycling stability, lasting over 2000 h at 1 mA cm−2 with 1 mAh cm−2. Furthermore, Zn//MnO2 full cells deliver remarkable stability, retaining approximately 89 % of their initial capacity after 3000 cycles at 5 A/g. This work proposes that the MGM[TFSI] additive can effectively regulate the interfacial chemistry of the Zn anode, providing an opportunity to design advanced electrolytes for highly reversible ZIBs and beyond.

A bifunctional thiobenzamide additive for improvement of cathode kinetics and anode stability in lithium-sulfur batteries

Lithium-sulfur batteries (LSBs) are considered as the key candidates for the next generation of energy storage devices. However, the practical applications of LSBs are hindered by the slow conversion of sulfur species and the inhomogeneous Li+ precipitation /stripping of lithium anode. Here, we report a bifunctional thiobenzamide electrolyte additive, 4-(trifluoromethyl) thiobenzamide (TFBCA), which synergistically improves cathode redox kinetics and anode stability. Polysulfides (LiPSn) are in-situ transferred to more reactive polysulfide intermediates (T-Sn-T), which significantly improve the liquid–solid reduction process by promoting the deposition dimension of Li2S. A LiF/Li3N-rich solid electrolyte interphase is formed with TFBCA, the uniform lithium deposition is achieved and the growth of lithium dendrites is suppressed. Correspondingly, LSBs with TFBCA show a high capacity (888 mAh·g−1 at 5C) and cycling stability (0.055 % per cycle after 600 cycles at 2C). Even under high sulfur loading (7.1 mg·cm−2) and low E/S ratio of 7, the LSBs also exhibit an areal capacity of 7 mAh·cm−2 after 50 cycles, and an energy density of 314 Wh·kg−1 is achieved for the pouch cell. This work demonstrates an efficient additive strategy through molecular structure design to construct high-performance LSBs.

Distribution of relaxation times-based analysis of aging mechanisms and prediction of heating domain for alternating current pulse self-heating lithium-ion batteries

Lithium-ion batteries (LIBs)-based electric vehicles (EVs) often encounter challenges such as the reduction in endurance mileage and the increase in charging time at low temperatures. To address these issues, the alternating current (AC) pulse self-heating in LIBs emerges as a pivotal method to overcome performance limitations of EVs at low temperatures. However, employing AC pulsing with high amplitude and low frequency can potentially lead to battery degradation. In this study, the state transitions and aging causes of LIBs during the self-heating are meticulously examined using the distribution of relaxation times (DRT) method. The results reveal that at an AC frequency of 50 Hz or higher, even with amplitudes up to 12 C, there is no degradation for the battery used in this study. For aged LIBs, the significant rise in impedance of solid electrolyte interphase (SEI) due to lithium plating, is the main factor driving battery aging during AC self-heating. Subsequently, an electrochemical-thermal coupling (ETC) model grounded in the degradation mechanism has been developed and experimentally validated to accurately predict the optimal heating domain for self-heating. This approach holds significant implications for the rapid selection of self-heating parameters for facilitating efficient battery performance enhancement.

Surface-Coating Strategies of Si-Negative Electrode Materials in Lithium-Ion Batteries

Silicon (Si) is recognized as a promising candidate for next-generation lithium-ion batteries (LIBs) owing to its high theoretical specific capacity (~4200 mAh g−1), low working potential (<0.4 V vs. Li/Li+), and abundant reserves. However, several challenges, such as severe volumetric changes (>300%) during lithiation/delithiation, unstable solid–electrolyte interphase (SEI) formation, and inherently low electrical and ionic conductivity, impede its practical application. To mitigate these challenges, direct contact between the surface of the Si particle and the electrolyte must be prevented. In this review, we elucidated the surface coating strategies to enhance the electro–chemical performance of Si-based materials. We identified the impact of various coating methods and materials on the performance of Si electrodes. Furthermore, the integration of coating strategies with nanostructure design can effectively buffer Si electrode volume expansion and prevent direct contact with the electrolyte, thereby synergistically enhancing electrochemical performance. We highlight opportunities and perspectives for future research on Si-negative electrodes in LIBs, drawing on insights from previous studies.

Interface stabilization strategy realizing low-temperature sodium storage in Sb anode prepared by ball milling method

Antimony (Sb) is an attractive anode material for sodium-ion batteries (SIBs) owing to its low operating potential, low cost, and high theoretical capacity. However, the large volume expansion of Sb during the Na alloying/dealloying process, which greatly limits its application in SIBs. Simultaneously, as the temperature decreases, the formation of a poor coating on the anode surface significantly increase the difficulty of Na+ transmission. Herein, Sb-graphite-NaF (SCF) ternary composites were prepared by an easy to operate and low-cost ball milling method, which significantly improved the cycling stability and extended to the operation temperature of Sb-base SIBs. A small amount of NaF induces the formation of an inorganic-dominated NaF-rich stable solid electrolyte interphase (SEI) on the Sb anode surface, which can cooperate with graphite to inhibit volume expansion of the Sb particles during sodium storage, enhance conductivity and accelerate Na+ diffusion at room and low temperatures. As a result, the SCF electrode with propylene carbonate-base electrolyte delivered a discharge capacity of 458.4 mAh g−1 after 160 cycles at 500 mA g−1 at 20 °C. When matched with diethylcarbonate-based electrolyte at −20 °C, it had a specific capacity of 299.8 mAh g−1 after 120 cycles and a capacity retention rate of 86.2 %. This study shows that the interface stabilization strategy with a suitable electrolyte can improve the cycling stability of anode materials, provide a new idea for constructing NaF-rich SEI, and a new approach for applying Sb-based materials in low-temperature SIBs.

Adaptive COF-PVDF composite artificial solid electrolyte interphase for stable aqueous zinc batteries

The cyclability of aqueous zinc (Zn) – based batteries is limited by the formation of dendrites and side reactions. Herein, this work presents a composite- artificial solid electrolyte interphase (ASEI) in two stages. Firstly, a covalent organic framework (COF) is synthesized via an interfacial reaction between aldehyde and amine linkers. Secondly, polyvinylidene fluoride (PVDF) is additionally coated on top of the COF film via spin coating. Results demonstrate that the COF-PVDF composite regulates Zn ion flux, preventing dendrite formation and reducing side reactions, while dynamically adapting to large volume changes. Zn plating/stripping tests with a symmetrical cell reveal that PVDF@COF@Zn exhibits enhanced stability and higher coulombic efficiency (CE) compared to bare Zn. Furthermore, the full cell incorporating PVDF@COFs@Zn//I2@C signifies significantly enhanced stability, making PVDF@COFs a promising ASEI material for stable aqueous Zn batteries. It is crucial to emphasize that the chemical and mechanical properties are the key parameters in designing the ASEI, as these factors directly influence its performance and longevity.

Quantifying the solid electrolyte interphase stress induced capacity fading of lithium-ion batteries via a multiscale mechanical-electrochemical coupling model

Quantifying the solid electrolyte interphase stress induced capacity fading of lithium-ion batteries via a multiscale mechanical-electrochemical coupling model

Comparison of different elastic strain definitions for largely deformed SEI of chemo-mechanically coupled silicon battery particles

Amorphous silicon is a highly promising anode material for next-generation lithium-ion batteries. Large volume changes of the silicon particle have a critical effect on the surrounding solid-electrolyte interphase (SEI) due to repeated fracture and healing during cycling. Based on a thermodynamically consistent chemo-elasto-plastic continuum model we investigate the stress development inside the particle and the SEI. Using the example of a particle with SEI, we apply a higher order finite element method together with a variable-step, variable-order time integration scheme on a nonlinear system of partial differential equations. Starting from a single silicon particle setting, the surrounding SEI is added in a first step with the typically used elastic Green–St-Venant (GSV) strain definition for a purely elastic deformation. For this type of deformation, the definition of the elastic strain is crucial to get reasonable simulation results. In case of the elastic GSV strain, the simulation aborts. We overcome the simulation failure by using the definition of the logarithmic Hencky strain. However, the particle remains unaffected by the elastic strain definitions in the particle domain. Compared to GSV, plastic deformation with the Hencky strain is straightforward to take into account. For the plastic SEI deformation, a rate-independent and a rate-dependent plastic deformation are newly introduced and numerically compared for three half cycles for the example of a radial symmetric particle.

Chloride-Ion-Enriched Solid Electrolyte Interphase with Rapid Na+ Migration toward High-Performance Sodium-Ion Batteries.

Sodium-ion batteries (SIBs) have emerged as potential alternatives to lithium-ion batteries (LIBs), particularly for large-scale applications. Alloy-type anode materials for sodium-ion batteries are esteemed as prospective candidate materials for sodium-ion anodes, owing to their elevated theoretical capacity, heightened utilization efficiency, and minimal production of insulating byproducts. However, the severe volume changes and sluggish ion diffusion kinetics can lead to irreversible particle fragmentation and reaggregation phenomena, ultimately resulting in electrode degradation. Additionally, repetitive volume changes can cause an unstable solid electrolyte interphase (SEI). This study presents the synthesis of chloride-ion-modulated bimetallic SnSb/C nanoparticle anode materials, highlighting the following advantages: (i) Designing a bimetallic SnSb alloy structure serves to buffer the structural stresses generated during sodium insertion/extraction processes, effectively mitigating particle fracture phenomena induced by electrode material expansion/contraction. (ii) Nanostructuring both alloy materials enables the full utilization of active materials and shortens diffusion pathways, thereby significantly enhancing the diffusion rate of sodium ions. (iii) Introducing a carbonaceous matrix serves to alleviate self-agglomeration phenomena of the material during charge/discharge cycles, enhancing the material's conductivity and structural stability. (iv) Utilizing chloride-ion interface modification to achieve a chloride-rich solid-electrolyte interphase (SEI) enhances battery performance.

Regulating Anode‐Electrolyte Interphasial Reactions by Zwitterionic Binder Chemistry in Lithium‐Ion Batteries with High‐Nickel Layered Oxide Cathodes and Silicon‐Graphite Anodes

AbstractThe practical application of silicon (Si)‐based anodes faces challenges due to severe structural and interphasial degradations. These challenges are exacerbated in lithium‐ion batteries (LIBs) employing Si‐based anodes with high‐nickel layered oxide cathodes, as significant transition‐metal crossover catalyzes serious parasitic side reactions, leading to faster cell failure. While enhancing the mechanical properties of polymer binders has been acknowledged as an effective means of improving solid‐electrolyte interphase (SEI) stability on Si‐based anodes, an in‐depth understanding of how the binder chemistry influences the SEI is lacking. Herein, a zwitterionic binder with an ability to manipulate the chemical composition and spatial distribution of the SEI layer is designed for Si‐based anodes. It is evidenced that the electrically charged microenvironment created by the zwitterionic species alters the solvation environment on the Si‐based anode, featuring rich anions and weakened Li+‐solvent interactions. Such a binder‐regulated solvation environment induces a thin, uniform, robust SEI on Si‐based anodes, which is found to be the key to withstanding transition‐metal deposition and minimizing their detrimental impact on catalyzing electrolyte decomposition and devitalizing bulk Si. As a result, albeit possessing comparable mechanical properties to those of commercial binders, the zwitterionic binder enables superior cycling performances in high‐energy‐density LIBs under demanding operating conditions.

Multifunctional fluorinated phosphonate-based localized high concentration electrolytes for safer and high-performance lithium-based batteries

This study introduces a novel fluorinated phosphonate-based additive, Bis(2,2,2-trifluoroethyl)(methoxycarbonylmethyl)phosphonate (BTCMP), in a localized high-concentration electrolyte (LHCE) to address key challenges in lithium metal batteries (LMBs), such as dendritic lithium growth and porous electrode morphology. The pristine LHCE forms a fluorine-rich solid electrolyte interphase (SEI) layer, primarily composed of lithium fluoride (LiF). However, the pristine LHCE suffers from severe electrolyte decomposition, forming a thicker and more resistive cathode electrolyte interphase (CEI), leading to increased impedance and reduced cyclability. Interestingly, Density Functional Theory (DFT) investigations revealed that the BTCMP inclusion modifies the solvation structure by dispersing the aggregates into smaller fragments, facilitating easier Li+ migration than the pristine LHCE. The addition of BTCMP suppresses solvent decomposition as confirmed by an increasing trend in the lowest unoccupied molecular orbital (LUMO) of corresponding LHCE molecules. Further, the presence of BTCMP results in a thinner and more stable CEI, reducing electrolyte decomposition, maintaining better ion transport, and preserving the cathode's structural integrity, as supported by TEM and XPS analysis. The BTCMP-based F-rich LHCE retained 82 % of its initial capacity while maintaining a coulombic efficiency of 99.5 % after 200 cycles in a Li||LNMO cell while the pristine LHCE only retained 47.2 % of initial capacity post-150 cycles. Additionally, the flame-retardant properties of BTCMP-based LHCE highlight its safety compared to commercial electrolytes.