Solar Radiation Research Articles

Significant dependence of the efficiency of energy-saving thermochromic VO2 on slight changes of its properties in the visible due to strain and/or vacancies

There are worldwide efforts to maximize the energy saving achieved by VO2-based thermochromic coatings. In particular, there are very different values of the modulation of integral solar energy transmittance, reported by various laboratories on various templates even for seemingly very similar coatings. A detailed analysis reveals that this is largely due to the combination of the intentional and well understood transmittance modulation in the infrared (always beneficial) with not yet understood slight transmittance modulation in the visible (sometimes beneficial, sometimes harmful, and always multiplied by strong solar irradiance). Ab-initio calculations are used to examine the hypothesis that the transmittance modulation in the visible can be controlled by lattice strain and/or slightly off-stoichiometric [O]/[V] ratio. The presented phenomenon opens a pathway which may lead, in a case of reproducible preparation of correctly altered VO2, to significantly enhanced energy saving.

Recyclable NiO/g-C3N4/ag hybrid substrates for sensitive SERS detection and photo-degradation of residual pesticides in beverages

In this research, we fabricated an innovative NiO/CN/Ag composite through the straightforward electrostatic assembly of Ag nanoparticles and g-C3N4 sheets onto NiO nanoflowers. This composite enables both surface enhanced Raman spectroscopy (SERS) detection and photo-degradation of pesticides. The results reveal NiO/CN/Ag can quantitatively detect thiram (TRM) and diquat dibromide (DQDB) in water, with a limit of detection (LOD) of 10−9 M, and also exhibit outstanding photo-degradation efficiency, exceeding 95 % for TRM and DQDB within 90 min under simulated sunlight. Significantly, after the organic reagent (citric acid) on NiO/CN/Ag was completely removed through simulated solar irradiation, the signal-to-noise ratios of SERS spectra on NiO/CN/Ag were enhanced, achieving LODs of 10−8 M for TRM and DQDB in different fruit juices and dried flower teas. Additionally, the composite demonstrate impressive recyclability, maintaining robust SERS signals and high degradation rates even after five cycles of “detection-degradation” processes.

Simple synthesis of K/P co-doped graphitic carbon nitride to enhance photocatalytic performance under simulated solar irradiation

The doping or co-doping of graphitic carbon nitride (g-C3N4) with other elements is a useful modification technique that overcomes the disadvantages of the base material and enhances its photocatalytic performance. In this study, K and P were successfully incorporated into g-C3N4 using a one-step, single-precursor (K2HPO4) synthesis method. The incorporation of K and P was confirmed using energy-dispersive X-ray spectrometry and wavelength-dispersive X-ray fluorescence spectrometry. Oxytetracycline (OTC) degradation rates were compared with and without elemental doping and with variation in the precursor content. In contrast to the low OTC degradation rate exhibited by pristine g-C3N4 (29.52 ± 0.03%), incorporating K and P into g-C3N4 greatly improved OTC degradation, with the sample produced using 100 mg of the precursor K2HPO4 (KPCN-100) achieving the highest degradation rate (99.43 ± 0.53%). The effects of the co-dopants K and P on the optical, photoelectrochemical properties, and band position of g-C3N4 were also investigated. Scavenging and N2 purging tests confirmed that reactive species, including O2•- (87.25%) and 1O2 (56.53%), played an important role in the degradation of OTC. In addition, several experimental parameters, including the presence of co-existing ions and humic acid, the pH level, the initial OTC concentration, and the photocatalyst dosage, were varied to better understand the photodegradation mechanisms at work within the KPCN-100 system. The stability of KPCN-100 and the toxicity assessment of the OTC intermediate were also conducted to evaluate their potential for environmental applications. Overall, this study demonstrates a simple synthesis method for the elemental co-doping of g-C3N4, offering an effective photocatalytic strategy that can greatly enhance the efficiency of OTC degradation.

Aerosol retrievals derived from a low-cost Calitoo sun-photometer taken on board a research vessel

This study presents a comprehensive 5-year period assessment of aerosol optical depth (AOD) and Å ngströn Exponent (AE) data from a hand-held Calitoo sun photometer on board the Ángeles Alvariño research vessel. Observations spanned March 2018 to September 2023, focusing on key maritime regions such as the Canary Islands, coasts of North Africa, the Mediterranean, Portugal, the Cantabrian, and the Bay of Biscay. The Calitoo device measures solar irradiance at three wavelengths (465, 540, and 619 nm). Uncertainty analysis for Calitoo AOD retrievals was performed using the Monte Carlo method, yielding an expanded uncertainty (UAOD) ranging between 0.008 and 0.050 with a mean and standard deviation of 0.032 ± 0.008 for the three wavelengths. Our results also highlight the remarkable calibration stability of the Calitoo (< 2.6%) over this 5-year period. Calitoo AOD values were assessed using reference AOD data from Santa Cruz de Tenerife (the Canary Islands), El Arenosillo (Huelva), and Palma de Mallorca (the Balearic Islands) AERONET (Aerosol Robotic Network) stations. The comparison revealed a good agreement with correlation coefficients ranging from 0.727 to 0.917 and mean bias ranging from -0.030 to -0.001. Additionally, the Calitoo AOD data were compared with MODIS (Moderate Resolution Imaging Spectroradiometer) and CAMS-ECMWF (Copernicus Atmosphere Monitoring Service-European Centre for Medium-Range Weather Forecasts) aerosol products obtaining that Calitoo AOD values were generally lower, showing negative mean bias of -0.063 and -0.024, respectively.The aerosol characterizations using AE vs. AOD plots in the three maritime study regions using 5-years of non-routine Calitoo data are similar to the corresponding aerosol characterizations performed with simultaneous AERONET-Cimel data.These findings underscore Calitoo’s reliability for aerosol studies in regions where AERONET instruments or other aerosol networks are unavailable. Likewise, given the low cost of Calitoo photometers, they could be deployed onboard a large number of merchant and passenger ships or in other remote or under-monitored areas, providing near real-time AOD/AE data to enhance our understanding of aerosols processes or for model or satellite assimilation/validation.

Numerical and experimental study on the evolution of thermal contrast for infrared detection of debonding in concrete filled steel tubular structure

Debonding in Concrete-Filled Steel Tubes (CFST) can reduce bridges’ overall load-bearing capacity and thus threaten the bridge’s structural safety. Infrared thermography (IRT) is widely used for CFST debonding detection due to its efficiency and non-contact advantages. However, IRT is often affected by complex environmental factors and faces challenges in achieving quantitative evaluation only based on thermal contrast. This study aims to reveal the relationship between thermal indicators and thermal contrast through numerical and experimental investigations of CFST debonding under varied mimicked climatic conditions. A 3-dimensional (3-D) heat transfer transient model of CFST is established to simulate the evolution of thermal contrast of debonding under different daily temperature variations and seasonal solar irradiance. Based on the finite element analysis results, the internal interface heat flux is found as a strong linear indicator correlating the thermal contrast to environmental factors. Model experiments then were conducted to verify the validity of this indicator. Finally, an infrared evaluation method for CFST debonding is proposed, which can linearly quantify the relationships among debonding sizes, environmental factors, and thermal contrast.

Perylene diimide configuration to construct g-C3N4 and iron phthalocyanine composite catalyst as PMS activator for contaminant degradation

The photocatalysis-assisted peroxymonosulfate (PMS) activation process has shown great potential for organic wastewater treatment. Herein, the composite photocatalyst (FeTAPc/PDI/CN) was obtained by grafting graphitic carbon nitride (CN) and amino iron phthalocyanine (FeTAPc) onto both ends of perylene tetracarboxylic anhydride (PTCDA) through an imidization process. Under simulated solar irradiation, the catalyst exhibited a remarkable degradation performance toward the target pollutant by activated PMS over a wide pH range from 3 to 11. The degradation efficiency of SMX reached 100 % in 7 min with the reaction kinetic constant of 0.845 min−1, which was 13 times higher than that of pure CN. In addition, the removal rate of FeTAPc/PDI/CN-4 for SMX was more than 80 % after 9 cycles. The introduction of phthalocyanine and PDI improved the separation efficiency of photogenerated electron-hole pairs. Furthermore, the active species involved in the SMX degradation were identified as •OH, SO4•-, •O2– and 1O2. The possible degradation pathways were proposed based on the identified intermediates, in which the oxidation of the amino group on the benzene ring was the main degradation pathway. This study is anticipated to result in a favorable method for designing CN-based photocatalysts with high stability and excellent catalytic activity for environmental remediation.

Street trees: The contribution of latent heat flux to cooling dense urban areas

Trees are the most important natural factor to alleviate the urban heat island effect and the latent heat flux (LE) they release contributes significantly to urban cooling. In this study, the model ENVI-met was used to study the influence of building geometry on the LE exchanged by trees at the block scale in compact urban areas. The building density (BD), building height (BH) and sky view factor (SVF) were used to characterize building geometry. The sensitivity of LE to building geometry was estimated by multi-linear regression analysis. The following conclusions were drawn:(1) the LE of trees is sensitive to building geometry, higher during daytime than night-time in winter and the higher during night-time than daytime in summer; (2) LE changes as expected across the seasons, with LE larger in summer; (3) The shade affects the LE of a tree by influencing the solar irradiance; (4) In winter the average LE of a single tree is larger with 0.06 than 0.12 fractional vegetation cover (FVC). This study can provide useful leads towards further research to explore latent heat exchanges by trees at the street scale.

Experimental study of photovoltaic-thermoelectric systems using thermal interface materials and natural cooling

This study investigates a novel approach to enhancing photovoltaic-thermoelectric generator systems by utilizing advanced thermal interface materials in real-world conditions. The research compares two experimental systems under natural air cooling employing different thermal interface materials: one features a pyrolytic graphite sheet, while the other uses conventional thermal grease, alongside a photovoltaic-only system for reference. An Arduino-based data logger accurately monitored key environmental and operational parameters. At peak solar irradiation, the system with the pyrolytic graphite sheet achieved a surface photovoltaic temperature of 39.01 °C, generating 4.90 W and an overall efficiency of 17.95 %. In comparison, the system with thermal grease had a surface photovoltaic temperature of 48.88 °C, generating 4.67 W with an efficiency of 16.87 %, while the photovoltaic-only system reached a surface photovoltaic temperature of 55.37 °C, producing 4.54 W and an efficiency of 16.42 %. The experimental data’s accuracy and reliability were validated against simulations from previous work, revealing error margins between 1.20 % and 3.03 %. These findings underscore the potential of pyrolytic graphite sheets as effective thermal interface materials to significantly enhance the efficiency and power output of photovoltaic-thermoelectric generator systems, offering valuable insights for optimizing renewable energy technologies.

A Calculation Study on the Escape of Incident Solar Radiation in Buildings with Glazing Facades

More and more modern buildings are using glass curtain walls as their building envelope. The large area of window leads to a significant increase in solar heat gain, resulting in an increase in the cooling load and energy consumption of the building envelope. In the calculation of building cooling load, the thermal performance parameter of windows, the solar heat gain coefficient, is used to calculate the solar radiation heat gain of the windows. The window-to-wall ratio of buildings with glazing facades is large, and the phenomenon of escape of incident solar radiation cannot be ignored. In order to calculate the solar radiation escape rate, a dynamic model of solar radiation escape rate incorporating the solar path tracking model is developed in this research, which can achieve big data simulation analysis based on actual meteorological conditions. The model is programmed and simulated using MATLAB R2024a software. Five representative cities from different climate regions in China are selected and the variation rule of solar radiation escape rate are analyzed on three different time scales: day, month, and year. The influence of building orientation was also calculated and analyzed. The numerical calculation results indicate that the escape solar radiation rate varies with the incident angle of solar radiation at different times. It was found that the smaller the solar azimuth angle and solar altitude angle, the smaller the escape rate of solar radiation. The latitude of a city has a significant impact on the solar radiation escape rate. The weighted average of the solar radiation escape rates for each city were calculated for both summer and winter. Regardless of the season, the city’s location, and the orientation of the room, the value of solar radiation escape rate varies from 8.64% to 10.33%, which indicates that the solar radiation escape phenomenon cannot be ignored in glass curtain wall buildings. The results can be used as a reference value of solar radiation escape rate for the correction of actual solar heat gain of buildings in different climate regions.

A multi-energy inertia-based coordinated voltage and frequency regulation in isolated hybrid power system using PI-TISMC

This paper proposes novel multi-energy inertia support for simultaneous frequency and voltage control of an isolated hybrid power system (IHPS). Multi-energy storage (gas inertia – hydrogen storage, thermal inertia – solar thermal storage, hydro inertia – gravity hydro storage, chemical inertia – battery energy storage) supported by demand side management (DSM) for simultaneous voltage and frequency regulation and backed by biodiesel generators, are the essential elements of IHPS. A novel control strategy of concurrent virtual droop control, virtual damping control, virtual inertia control, and virtual negative inertia control is proposed to utilise multiple inertia sources and to improve LFC and AVR performance effectively. The effective coordination of inertia sources in eradicating oscillations in IHPS, is aided by a developed cascaded proportional integral-tilt-integral-sliding mode (PI-TISMC) controller. The performance of PI-TISMC is compared with PID, PI-PID, and PI-SMC controllers. A maiden attempt has been done by training five diverse classes of optimization techniques to optimize the parameters of controllers in the present work. The results are evaluated in MATLAB and it is evident from the results that the performance of frequency control is improved by 6.5%, 7.8% and 3.4 s (over shoot, undershoot, and settling time). The performance of frequency control is improved by 6.5%, 7.8% and 3.4 s (over shoot, undershoot, and settling time). Similarly, the performance of voltage control is improved by 6.7%, 4.8% and 2.3 s (over shoot, undershoot, and settling time) by employing developed PI-TISMC controller and proposed concurrent inertia control. The combination exhibits superior performance in minimizing oscillations in IHPS due to variations in loading and solar insolation.

Irrigation rates and turfgrass evapotranspiration in cities with contrasting water availability

AbstractAs water scarcity is worsened by drought and climate change, there is more interest in efficient management of urban irrigation, requiring understanding of the drivers of evapotranspiration (ET) and the role of irrigation inputs. We developed and validated a method to accurately measure ET of turfgrass lawns in contrasting climates using portable static chambers. We made in situ measurements of ET and irrigation inputs in lawns across three metropolitan areas in the United States with varying climatic conditions, water availability, and water conservation policies: Salt Lake Valley, Utah; San Fernando Valley, California; and Tallahassee, Florida. In full sun, mean daily ET estimates (ETsun) were 0.7 ± 0.4 mm day−1 in Tallahassee, 1.6 ± 0.8 mm day−1 in Los Angeles, and 3.3 ± 1.1 mm day−1 in Salt Lake Valley. In the shade, daily ET estimates (ETshade) were two to three times lower. In all three regions, ET was primarily driven by solar radiation (I0) and atmospheric vapor pressure deficit (D). Across the cities, irrigation rates were a key driver of ET, along with I0 and D. Daily irrigation ranged from 0 mm day−1 in Tallahassee (most were unirrigated) to 1.9 ± 1.2 mm day−1 in Los Angeles and 5.1 ± 2.9 mm day−1 in Salt Lake Valley. ET increased linearly with irrigation up to ~3 mm day−1, after which ET remained relatively constant despite irrigation increases. Our results highlight the importance of accounting for nonlinear responses and shading effects on ET in developing accurate irrigation recommendations.

Theoretical Analysis of a Novel Rock Wall to Limit Heating Demands in Historical Buildings

In the near future, the building sector will continue to absorb the greatest share of primary energy worldwide. It is necessary to find innovative solutions that promote energy efficiency through renovation measures, especially in historical buildings, for which refurbishment is constrained by several issues. In this study, we propose a novel Trombe Wall configuration that is easily integrable and based on a rock wall made of caged stone to use as a thermal accumulator. The system was investigated preliminarily using a transient Finite Difference Method (FDM) code to analyse the temperature field inside the rock wall. Successively, FDM results were employed as input data in TRNSYS simulations to determine the savings achievable in thermal heating requirements. The results demonstrated that the proposed solution, in the considered climate and on a reference historic building, can produce monthly heating savings varying between 26% and 85%. So, the rock wall results in a reliable solution for buildings in which refurbishment is difficult, allowing for preserving aesthetic features and improving energy efficiency by rationally using solar radiation.

Investigation of Chinese-Style Greenhouse Usage Across Europe

Chinese-style greenhouses (CSGs), characterized by a distinct geometric shape compared to traditional greenhouses, are extensively utilized in China. In this study, this type of greenhouse was modeled using TRNSYS software version 18 and experimentally validated. The model can transiently determine the indoor conditions of the greenhouse and the requirement for additional heating. It calculates the heat loss due to plant evapotranspiration as well as all the heat gains and losses from the surfaces. The application of this greenhouse has been investigated from the southernmost to the northernmost regions of Europe. For this purpose, cities located at different latitudes (between 32.63° N and 69.65° N) were entered into the model, and the results were obtained and compared. The analysis conducted over the entire year demonstrated that the CSG indoor temperature is more dependent on solar energy during the day and on outdoor temperature at night. The two southernmost cities in our survey, Funchal, Portugal (32.63° N) and Luqa, Malta (35.83° N), had no winter heating requirement. The thermal covering was sufficient to minimize night heat loss and maintain a suitable indoor temperature. In northern cities, the heating requirement was relatively high due to the lower outdoor temperature and solar radiation. Consequently, the duration of the heating season increases towards the north. In the northernmost city, Tromso, Norway (69.65° N), the heating season was determined to last 12 months. In the absence of solar energy, the transparent surface of the greenhouse is covered with thermal insulation to prevent heat loss. It has been shown that with the appropriate selection of this thermal covering, which is controlled based on the presence of instantaneous solar energy, up to 80% savings can be achieved from additional heating in southern cities. In the north, this rate can be increased up to a maximum of 70% by increasing the thermal covering thickness.

Design Of A Hybrid Power Generation System in Cipatujah Tasikmalya Regency

The escalating daily demand for electricity, propelled by technological advancements and the pervasive use of electronic devices, accentuates the imperative for a dependable and sustainable power generation system. Renewable energy sources emerge as a viable solution to address the electricity needs in Indonesia, particularly in remote areas where access to the main grid is challenging. Tasikmalaya Regency, situated in West Java Province and defined by its geographical coordinates between 7°02' 29" - 7°49' 08" South Latitude and 107°54' 10" - 108°25' 52" East Longitude, presents a promising setting for the implementation of such sustainable energy solutions. The coastal area of Tasikmalaya, specifically Cipatujah Subdistrict, exhibits substantial renewable energy potential, including wind, solar radiation, and ocean waves. This research endeavors to design an efficient hybrid power generation system in Cipatujah Subdistrict using HomerPro software. The methodology involves crafting various models to determine the most economically efficient generation strategy. The study utilizes electricity consumption data sourced from the Karangnunggal Tasikmalaya Substation, situated in the southern coastal region of Tasikmalaya, particularly in Cipatujah Subdistrict, with a daily consumption of 20.6917 MW. By addressing the specific energy needs of the region, the research aims to make a positive contribution to the development of renewable energy and, concurrently, serve as a guiding framework for similar system designs in locations sharing comparable characteristics. This multifaceted approach underscores the significance of tailoring sustainable energy solutions to the unique requirements of diverse regions, fostering a broader transition towards a reliable and environmentally conscious energy future.

Impacts of Climate Change on Forest Biodiversity Changes in Northeast China

Vegetation plays a vital role in connecting ecosystems and climate features. The biodiversity of vegetation is one of the most important features for evaluating ecosystems and it is becoming increasingly important with the threat of global warming. To clarify the effects of climate change on forest biodiversity in Northeast China, time-series NDVI data, meteorological data and land cover data from 2010 to 2021 were acquired, and the forest biodiversity of Northeast China was evaluated. The effect of climate change on forest biodiversity was analyzed, and the results indicated that the forest biodiversity features increased from west to east in Northeast China. There was also an increasing trend from 2010 to 2021, but the rate at which forest biodiversity was changing varied with different forest types of Northeast China, as different climatic factors had a different impact on forest biodiversity in different forest types. Average annual temperature, annual accumulated precipitation, CO2 fertilization and solar radiation were the main factors affecting forest biodiversity changing trends. This research indicated the potential impact of climate change on forest ecosystems, as it emphasized with evidence that climate change has a catalytic effect on forest biodiversity in Northeast China.

Smartphone Light Sensors as an Innovative Tool for Solar Irradiance Measurements.

In recent years, the teaching of experimental science and engineering has been revolutionized by the integration of smartphone sensors, which are widely used by a large portion of the population. Concurrently, interest in solar energy has surged. This raises the important question of how smartphone sensors can be harnessed to incorporate solar energy studies into undergraduate education. We provide comprehensive guidelines for using smartphone sensors in various conditions, along with detailed instructions on how to calibrate them with widely accessible clear-sky satellite data. This smartphone-based method is also compared with professional reference measurements to ensure consistency. This experiment can be easily conducted with most smartphones, basic materials, and a clear, open location over a few hours (methods). The findings demonstrate that smartphones, combined with simple resources, can accurately measure solar irradiance and support experiments on solar radiation physics, atmospheric interactions, and variations in solar energy across locations, cloud cover, and time scales. This approach provides a practical and accessible tool for studying solar energy, offering an innovative and engaging method for measuring solar resources.

A Case Study on Deep Learning for Photovoltaic Power Forecasting Combining Satellite and Ground Data

The increasing demand for clean energy presents challenges in energy supply management, largely due to their intermittency. Photovoltaic power generation, in specific, is greatly affected by weather factors, which may render power grids susceptible to instability, quality and balance issues. In this context, photovoltaic power generation forecasting is crucial not only to enhance the management of diverse energy sources through generation planning, but also to ensure widespread adoption of photovoltaic energy. To address the predictability issue in generation, this study aims to investigate the combination of satellite data with meteorological data to predict the energy generation potential in photovoltaic panels within 30, 60, 120, and 180-minute horizons. For this purpose, images from the GOES-16 satellite are used in combination with data from a ground-based weather station, located at Florianópolis – Santa Catarina – Brazil. The data is fed to a convolutional neural network, where convolutions are employed to extract features from the satellite images, aiming to establish a relationship with solar irradiation. The output of the convolutional network serves as input for a multilayer perceptron network, which utilizes the data to predict the Global Horizontal Irradiance (GHI). Our results support that models incorporating satellite images provide forecasts approximately 41% better for the 30-minute horizon and 21% better for the 180-minute horizon, when compared to models without satellite images.

Electric field modulation of electronic structure, charge transfer, and nonlinear optical properties of crocetin for dye-sensitized solar cells

Natural sensitizing dyes in solar energy applications have gained attention due to their sustainability, cost-effectiveness, and environmental friendliness. However, enhancing their performance, light-harvesting efficiency, and durability requires a deeper understanding of their structural and electronic properties under solar irradiance. Accordingly, this study explores the electronic structure and nonlinear optical properties of crocetin dye (cis and trans conformers) under varying external electric fields using M06-2X/6-311+G(d,p) model chemistry. The absorption characteristics strongly depend on field intensity, with electron injection efficiency expected to decrease as the field increases. Key nonlinear optical (NLO) parameters, such as dipole moment, polarizability, and hyperpolarizabilities, were calculated at solar irradiance peak frequencies. The NLO properties are wavelength-independent in the infrared region but show significant wavelength dependency in the visible region, increasing substantially near the absorption energy.

Management of Generalized Vitiligo in Adolescent with Tofacitinib: Clinical Case

Background. Vitiligo is a depigmenting skin disease characterized by selective loss of melanocytes leading to development of typical white spots. There are various theories on vitiligo etiology: genetic, autoimmune, neurogenic, autoinflammatory, oxidative stress theory, and many others. Generally accepted dominant role is given to the concept of its autoimmune nature. Vitiligo management traditionally includes different methods of phototherapy, topical and systemic glucocorticoids (GC), and calcineurin inhibitors. Recently, Janus kinase inhibitors (JAK) have shown its efficacy in treatment of vitiligo. Clinical case description. 13-year-old male adolescent has complaints of hypopigmentation areas on the skin of face, trunk and limbs that appeared after active solar insolation during summer vacation. Dermatologist has determined a diagnosis of vitiligo according to clinical picture. Topical GC of the 3rd activity class were used for treatment, as well as course of local narrow-band medium-wave photodynamic therapy (311 nm, No. 30) with no significant effect. The patient was admitted to the dermatology department of Research Institute of Pediatrics and Children’s Health in Petrovsky National Research Centre of Surgery where therapy with JAK inhibitor, tofacitinib, was initiated due to inefficacy of previous treatment and the generalized form of the disease. Conclusion. Management of vitiligo with JAK inhibitors, in particular tofacitinib, is a promising method and it can lead to significant clinical effect with safety profile comparable to conventional therapies for this pathology.

Youth Climate Questions

AbstractAnthropogenic climate change and environmental crises are pressing challenges of our time, with changes to the climate system observed in every global region. Disastrous impacts on nature, including people, have already been observed in the form of drought, floods and extreme heat events across the planet. This study examines the role of an interdisciplinary approach to exploring different responses to climate-related disasters and potential disasters. The work we report takes place in the context of recent research on dialogue on climate interventions with youth. Climate interventions are large-scale interventions into the Earth’s climate system and include proposals such as solar radiation management, ocean liming, and carbon capture and storage technologies. Research and development of climate interventions as a response to one set of disasters (in the present and in-the-making), created as a result of anthropogenic climate change, are associated with much uncertainty and controversy. We explored these uncertainties and controversies with young people, scientists and policymakers, resulting in a set of illustrated climate conversation cards. In this paper, we analyse the questions produced by young people to find requests for data and knowledge from across disciplines, and for an exploration of ethics, feelings, positions and priorities. We also found problematisations of technofixes and desire for socio-political action. The implications for science and disaster education are discussed.