Softwood Plantations Research Articles

Board assignment heuristics for nail laminated out-of-grade timber

ABSTRACT Structural sawn timber, sourced from softwood plantations, is widely used in lightweight timber-framed residential housing and in engineered wood products for contemporary mass timber construction. However, a significant proportion of milled timber boards are considered ‘out-of-grade’, failing to attain a structural grade under existing classifications systems due to various stiffness, strength, and/or utility-limiting features. This study investigates the potential of controlled lamination techniques to produce structurally usable laminated timber products from out-of-grade timber, using a minimal number of requisite boards. Numerical and experimental methods were employed to compare different board assignment heuristics, in terms of reducing the stiffness variability in laminated board populations. The results indicate that controlled board locations produced remarkably consistent laminated products, achieving very low variability even with a minimum lamination of only two boards. The findings of this paper suggest that controlled lamination techniques have the potential to transform low-value out-of-grade timber into a valuable resource for value-added applications, challenging the existing market perception that out-of-grade timber lacks structural usability.

Comparative Studies on Tensile Mechanical Properties of Water-Saturated Earlywood and Latewood within the Same Growth Ring from Masson Pine

The tensile mechanical behavior of water-saturated earlywood (EW) and latewood (LW) within the same growth ring of Masson pine (Pinus massoniana) was investigated in the hydrothermal environment and discussed with respect to the density and microfibril angle (MFA) of the wood specimens. The tensile modulus, tensile strength, and strain at failure of EW and LW in the longitudinal (L) and tangential (T) directions were determined at different temperature levels ranging from 30 °C to 80 °C. Major differences in the tensile mechanical properties were found between EW and LW in the L and T directions. Compared to LW, EW showed a smaller density and a larger MFA, resulting in a lower tensile modulus, lower tensile strength, and higher strain at failure. Compared to the L specimens, the T specimens showed lower tensile modulus, lower tensile strength, and higher strain at failure. As the hygrothermal temperature increased, the MFAs, tensile modulus, and tensile strength of EW and LW specimens decreased, except for the MFAs of LW, while the strain at failure of the specimens showed the opposite trend. Variations in the tensile mechanical behavior between EW and LW were mainly influenced by the density and MFA of the specimens, and are closely associated with the hydrothermal softening properties of wood. These findings contribute to a further understanding of the structural–mechanical relationships of Masson pine wood at the cell wall level, and provide a scientific basis for the better utilization of plantation softwood in the hydrothermal environment.

Indicators for measuring and reporting corporate nature-related impacts, dependencies, and risks

Businesses are embedded within nature. Their supply chains, operations, and products fundamentally depend on and impact nature. These impacts and dependencies can give rise to nature-related risks (as well as related opportunities). However, despite growing expectations from stakeholders, most businesses are currently not adequately measuring and reporting on these. To date, it has not been clear whether this requires the development of entirely new indicators, or whether various existing sustainability reporting frameworks could provide sufficient information on nature-related risks. This paper evaluates the decision-usefulness of existing indicators for the softwood plantation forestry industry in Australia. Decision-usefulness is assessed against three criteria: (1) relevance and completeness; (2) faithful representation; and (3) comparability. The results show some potential for adaptation of indicators already used in sustainability-related corporate accounting and reporting, which could help reduce the reporting burden and encourage uptake. However, gaps remain in measuring the financial consequences for business from nature-related risks and in providing sufficient comparable information to evaluate performance across industries and locations. Implications are discussed in relation to recent recommendations from the Taskforce on Nature-related Financial Disclosures (TNFD) and International Sustainability Standards Board (ISSB) sustainability standards IFRS S1 and S2.

Gluing characteristics of Papua New Guinea timber species for various non-structural applications

Papua New Guinea (PNG) has abundant natural forest resources but there are many constraints which need to be addressed to support the development of competitive value-added wood industries. There is a need to develop knowledge and capacity in wood science and processing technologies which support successful domestic value-adding wood processing enterprises. A comprehensive testing program has been developed to assess the glue‐bond strength and performance of selected commercial PNG timber species in various climatic conditions to simulate service conditions in potential market destinations. Two criteria namely shear strength and wood failure have been used to determine if a species can meet the minimum requirements for either dry use or wet use applications. The performance of 24 different PNG commercial timber species has been assessed using a one-component cross-linking polyvinyl acetate emulsion adhesive. The bondability of the selected species has been carefully estimated considering the wood density and wood moisture content for the strength and durability in dry- and wet-use conditions. The testing results show that as the wood density as a wood property factor and moisture content as a service condition factor increase, high shear strength with high wood failure become more difficult to achieve consistently. The highest shear strength and wood failure results were achieved by softwood plantation species and low-density hardwood species. Based on the testing results, the selected species have been classified into bondability classes (bond very well, bond well, bond with difficulty, very difficult to bond).

A short Literature Review on Sawlog and Pulpwood Transport Efficiency and Fuel Consumption

Timber transport is one of the main components of woody supply chain, which causes high costs and considerable emissions depending on truck size, type, transport distance, and payload. A cradle-to-gate life cycle assessment of Softwood plantations and regrowth hardwood native forests estimated that the most significant contributor to total greenhouse emissions per unit of wood production in softwood plantation was log haulage at 37%. For regrowth native hardwood forests, log transportation contributed 23% of greenhouse gas emissions. This research, built on existing literature, focused on how timber harvesting transportation costs and emissions to the environment can be reduced, specifically, the transport of the industrial timber logs from the Forest Stockpile to the processing facility or unloading points. The review summarized the data and highlighted that the efficiency and emissions data could be categorized into five themes: Higher Capacity Transportation (HCT), Road Networks & Surfaces, Logistics and Planning, Fleet Replacement, and Fuel efficiency technologies. Fuel efficiency improvements across these themes ranged from 3% to 43% within the reviewed case studies. Several studies researched the fuel efficiency of High Capacity Transport indicated that the fuel consumption in liters per ton kilometer was 8-11% lower in the 92-tonne combination HCT compared to a 72-tonne combination HCT due to the increased payload for High Capacity Transport. Road networks and the composition of the surfaces have been shown to have a strong correlation to emissions. Studies have shown a 16.7% increase in emissions from a network of predominantly highways to a higher proportion of Forrest and Gravel roads. Studies that included data on vehicle age found efficiency improvements of up to 26% when new vehicles’ fuel consumption was compared to older vehicles. Newer truck fleets incorporate newer technologies, with reports showing fuel consumption improvements of up to 43% with less than a two-year payback period.

Fine scale 20‐year timeseries of plantation forest evapotranspiration for the lower limestone coast

AbstractCommercial plantation forestry is a vital industry worldwide, providing natural resources for humans and playing an important role in carbon sequestration. Historically, impacts of plantation development to natural resources such as surface and groundwater was not considered, however demand for water and drying climates has focussed attention on sustainable water use and extraction. The Lower Limestone Coast region of south‐east South Australia has an extensive softwood plantation estate. The region is characterised by minimal surface water and substantial, fresh karstic groundwater resources, often <6 m below ground. Rapid expansion over shallow groundwater of the plantation hardwood estate from 2000, prompted concern about impacts of deep‐rooted plantations on water resources and notably contracting wetlands. To quantify plantation estate water use, an extensive evapotranspiration (ET) field study (1999–2008) identified plantation areas with <6 m to groundwater as groundwater users, leading to water policy whereby plantations are considered licenced water users. To enable plantation expansion in the region, fine resolution, broadscale ET data is required to ensure optimum use of water licences in the forest industry and account for plantation groundwater extraction. As continual field studies are not feasible, this 20‐year, monthly 30 m ET dataset for the region was developed to improve estimates of plantation water use, enabling improved, dynamic estimates of groundwater extraction. The dataset was developed using 21 long‐term field sites where ET was derived based on field measured transpiration, soil moisture, canopy interaction and rainfall data. Region specific field ET was combined with machine learning and additional remote sensing layers to estimate monthly ET (R2 = 0.86) across the plantation estate, improving on a national remote sensing ET product. Currently, groundwater extraction is accounted for via modelling which excludes dynamic changes in plantation groundwater extraction, limiting understanding of the hydrological processes influencing available water resources and potentially impeding economic growth.

Full Scale Evaluation of GFRP Confined Softwood after Long-Term Exposure to High Humidity Environment

Plantation softwood timber poles are associated with low natural durability, and it is also not clear what the effects of the high humidity environment on the long-term performance of composite action integrity of such a system. This paper presents a durability study for the proposed composite poles using (GFRP) glass fiber-reinforced polymer as a confinement system on wooden poles sourced from plantation softwood timber. Radiata pine poles of 6 m length were wrapped with multiple layers of 0°/90° woven roving biaxial E-glass fiber sheets through a wet layup process as confinement. The prepared GFRP softwood poles were then subjected to high humidity environmental conditions of up to 95 ± 2% relative humidity and 22 ± 2 °C temperature for a period of 30 months. Various lengths of confinement were considered in this study ranging from 0% to 70% of the span length. The poles had a span length of 5.4 m and were tested using a three-point bending test. Results showed that the proposed confinement system of GFRP-softwood provided a satisfactory long-term performance and the high humidity environment did not greatly affect the improvement in the mechanical performance that the GFRP system provided.

The impact of soil, altitude, and climate on tree form and wood properties of plantation grown Pinus patula in Mpumalanga, South Africa

Abstract Plantation forests were originally established in South Africa to meet an increasing demand for solid wood products as there was a limited supply from native forests. The majority of the commercial softwood plantations were established with Mexican Pinus patula. Since growing conditions are known to impact tree growth, tree form, and wood quality of P. patula, sample plots were established over a cross-section of plantations in the Lowveld Escarpment and Highveld forestry regions of South Africa that covered an array of geologies and altitudes. Each sample plot was classified according to soil properties, rainfall, and temperature, and trees within the plots were measured for growth, form, and wood properties. Soil, growing days, and temperature were found to have little impact on tree form and wood properties. However, rainfall and specifically, spring rainfall, was found to have a highly significant impact on late wood formation, proportion of juvenile core, and wood density. In addition, tree height was found to be strongly correlated with maximum annual temperature.

Forest succession, management and the economy under a changing climate: Coupling economic and forest management models to assess impacts and adaptation options

Climate change is expected to have significant impacts on forests by affecting the successional dynamics of tree species and the performance of plantations, among others. Research is needed to better understand how these factors will affect forests and economies in different regions, and how we can best adapt. To shed some light on these issues, we couple an economic (Computable General Equilibrium) model with a forest management (Woodstock) model to analyze the potential climate change impacts and adaptation options on timber supply and the economy over the 2015–95 period in a case-study province of New Brunswick, Canada. We estimate that climate change may have relatively large negative impacts on softwood timber supply (at 26% by 2095), softwood forestry & logging sector output quantity (at 12% by 2095), and softwood-dependent forestry manufacturing sector output (ranging from 6% to 27% by 2095). Negative impacts on GDP may be relatively smaller (at up to a 0.33% reduction by 2095). Adapting to these climate-related changes by planting drought-resistant softwood seedlings or hardwood seedlings in place of failed softwood plantations can minimize these negative impacts, and in the latter case, positively impact hardwood timber supply and output. While the former adaptation option is supported using cost-benefit analysis, the latter is not – due to the large incremental costs of growing, planting, and tending hardwood seedlings. Methods developed in this study can be applied in other regions to help guide decision-making around forest management in the face of a changing climate.

The Effects of Rehabilitation Treatments on Landscape Function Within a Softwood Plantation After Fire: Implications for Catchment Management

AbstractThere is global interest in enhancing the ecosystem services provided by landscapes and catchments dominated by plantation (monoculture) forestry. Partial reversion of plantations to locally native species (reforestation) is one option. However, the ecological outcomes of this kind of plantation reversion are poorly known. The partial reforestation of a pine plantation (Pinus radiata D. Don 1836) in the Australian Capital Territory with native species following a wildfire provides a rare case study of the environmental consequences of such a reversion. We estimated changes in landscape functionality by measuring indices of water infiltration, nutrient cycling, and soil surface stability across five landscape-scale treatments after the 2003 Lower Cotter Catchment bushfire: (1) natural regeneration of a native forest burned in 2003, (2) burned pine plantation replanted to pines, (3) burned plantation replanted to native trees and shrubs, (4) burned plantation allowed to naturally regenerate, and (5) forest roads rehabilitated by planting native trees and shrubs. At 14 years after the fire, we found that the regenerating native forest had the highest indices of water infiltration, nutrient cycling, and soil surface stability. The burned pine plantation that was replanted to pines in 2005 had indices of functionality that were higher than the burned plantation areas that were either allowed to naturally regenerate to native eucalypt forest or were planted with native forest species. These two types of native forest rehabilitation treatments had only minor differences in functionality. The rehabilitated closed roads were the least functional. We found that a pine plantation at the closed canopy stage can supply regulating services of water infiltration, nutrient cycling, and soil surface stability comparable to a native forest at a similar stage postfire; however, a significant limitation of the plantation was its low ecosystem resilience. It required massive soil disturbance to replant postfire and long-term maintenance of an extensive unpaved road network. The active or passive rehabilitation of native forest is justified to improve the natural resilience to wildfire. However, this rehabilitation of a native forest following use as a pine plantation is a multidecade process in this relatively low-rainfall environment.Study ImplicationsThe 2003 Canberra bushfire destroyed the entire pine plantation at Lower Cotter Catchment, a water catchment in Australian Capital Territory, but also provided an opportunity to examine and quantify changes in ecosystem functions with different restoration treatments. Landscape Function Analysis, including three indices (water infiltration, nutrient cycling, and soil surface stability), was used in this study. Findings suggest that both native eucalyptus forests and pine plantations recovered to relatively high levels of functionality within just 15 years after the bushfire, compared with all other restoration treatments, but plantations of Pinus radiata are not resilient to wildfire from a commercial perspective. These results help to justify the controversial decision to restore the majority of the catchment with native species in 2005. However, long-term monitoring is needed to determine how long it will take for the replanted and natural regeneration treatments to approach the functionality of the native forest.

Comparative studies on wood structure and microtensile properties between compression and opposite wood fibers of Chinese fir plantation

The microtensile properties of mechanically isolated compression wood (CW) and opposite wood (OW) tracheids of Chinese fir (Cunninghamia lanceolata) were investigated and discussed with respect to their structure. Major differences in the tensile modulus and ultimate tensile stress were found between CW and OW fibers. Compared to OW, CW showed a larger cellulose microfibril angle, less cellulose content and probably more pits, resulting in lower tensile properties. These findings contribute to a further understanding of the structural–mechanical relationships of Chinese fir wood at the cell and cell wall level, and provide a scientific basis for better utilization of plantation softwood.

How roots of Picea abies and Fraxinus excelsior plantations contribute to soil strength and slope stability: evidence from a study case in the Hyrcanian Forest, Iran

Although the effects of different vegetation cover on soil reinforcement due to their roots have been addressed in the literature, there remains a lack of assessment and comparison of root biomechanical properties of hardwood and softwood plantations for similar site conditions. To address this gap, two adjacent hillslopes with similar site conditions but different forest plantations, a Picea abies (softwood) and a Fraxinus excelsior (hardwood), were selected to assess and compare their effectiveness in protecting sloping soils. The profile trench method was used to obtain root distribution from both upslope and downslope sides of tree samples and on each side at two horizontal distances from the tree stems. Root tensile strength of live root samples was measured using a standard Instron Universal Testing Machine. A modified Wu and Waldron root reinforcement model was used to calculate root cohesion for the two plantations. The root tensile strength for was significantly greater for softwood than for hardwood trees (19.31 ± 2.64 vs 16.98 ± 1.01 MPa). Interestingly, the number of roots, root area ratio values, and the root tensile strength of the two species did not significantly differ between the upslope and downslope sides of trees. The results also showed a higher root cohesion for the softwood than the hardwood species (1.56 ± 0.34 vs 1.03 ± 0.21 kPa). In addition, softwood trees extended their contribution to soil protection to a larger horizontal distance compared with hardwood. However, our findings generally revealed that the values of root cohesion of both studied plantations were surprisingly lower than those found in earlier reports.

Age Dynamics of Wind Risk and Tree Sway Characteristics in a Softwood Plantation

Quantifying wind risk in planted forests is critical to ensure the provision of wood-based biomaterials and forest ecosystem services in the future. Tree sway dynamics play a major role in determining their vulnerability to wind storms. While structural engineering theory can greatly assist in predicting tree and branch motion accurately, the effects of forest aging and silvicultural treatments on motion and the likelihood of mechanical failure are still poorly understood. In this study, we simulate the growth of an individual model tree and its architecture for a managed, even-aged pure Cryptomeria japonica D. Don. stand. The dynamic behavior of the tree is predicted for a rotation period at a five-year interval using finite element analysis. Results show that tree natural sway frequency is subject to a five-fold decrease over the tree’s lifetime. The tree is thus more susceptible to absorb turbulent kinetic energy from the wind as it grows older. The damping ratio, which measures how rapidly the tree can return to its rest position after being deflected, is predicted to increase by a factor of four. By simulating the mechanical response to a wind gust, the model predicts a quick transition from a low risk of failure in the juvenile phase to a high-risk situation in the mature phase. The transition occurs between ages 15 and 30 when canopy closure takes place, when juvenile wood formation stops in the lower stem region and when the first thinning is carried out. Wind risk plateaus after the transition period. The age-risk relationship shown by the model is consistent with post-typhoon damage patterns documented by inventories in Japanese planted forests, albeit with a sharper transition.

Drought risk to timber production – A risk versus return comparison of commercial conifer species in Scotland

Climate change will alter precipitation patterns across the world increasing drought risk to forests in some areas, especially where summer precipitation is reduced. Effective management of this risk requires quantified information on the probabilities and consequences of drought to support policy and strategic decisions on the choice of tree species that will provide drought resilience and ensure continued timber supply. Here we define a new approach to delivering this information to underpin management decisions on species choice for restocking. We derive location-specific risk versus return analyses, for twenty commercial timber species in Scotland, by quantifying the impact of drought risk under a high emission scenario on potential return, modelled as change in baseline volume of timber production (yield in m3 ha−1). We find that the current potential yield of Sitka spruce is likely to be sufficiently high to compensate for its relatively high drought susceptibility compared to alternative species, modelled over a new 50-year rotation. In regions projected to experience increased drought risk - particularly central and eastern areas of Scotland - the higher drought tolerance of some species means that they are likely to be viable alternatives to Sitka spruce, based on a threshold productivity which we set for the purposes of this analysis as ≥90% of predicted Sitka spruce yield. Since species diversification is a potential strategy to increase forest resilience against other risks, such as those from pest and diseases, our analysis provides a framework within which these regional decisions can be made. Risk management strategies should be introduced which include the risk from drought to commercial softwood plantations and thereby help protect timber volume production. The modelling approach outlined could be adapted to compare timber species in other regions where comparable data are available.

Patterns of Genetic Diversity in Highly Invasive Species: Cogongrass (Imperata cylindrica) Expansion in the Invaded Range of the Southern United States (US).

The spatial expansions of invasive organisms in the novel range are generally expected to follow an isolation-by-distance relationship (IBD) if the invasion is biologically driven; however, many invasions are facilitated anthropogenically. This research focused on the extant expansion patterns of cogongrass (Imperata cylindrica). Cogongrass is a widespread invasive species throughout the southern United States (US). Patterns of infestation vary among US states. Cogongrass is pyrogenic, and its invasion threatens softwood (Pinus spp.) plantations, a substantial economic market for this US region. Over 600 individuals were sampled from seven invaded US states, using amplified fragment length polymorphisms (AFLPs) to assess genetic diversity and population structure. We suspected that differences in historical management efforts among US states influenced differences in genetic diversity and structure. We detected two genetic lineages at the highest level of analysis. One genetic lineage was locally restricted, whereas the other was found throughout the study region. Admixed individuals were found in all US states and consistently co-occurred with the dominant lineage, suggesting that secondary contact and hybridization may have facilitated expansion. The widespread prevalence of only one of the two detected genetic lineages suggests a primary genetic lineage responsible for on-going population expansion in the US.

Mechanical performance of fibre reinforced polymer confined softwood timber for pole applications

Hardwood as sourcing of utility poles becomes difficult and costly due to its slow replenishment and the high clearing rates in the 19th century as well as occasional bushfires. There is a critical need to source other timber species for timber poles. This paper presents a study of using fibre reinforced polymer (FRP) composites as a confinement system onto plantation softwood for utility poles. The proposed method was a wet layup process using multiple layers of 0°/90° biaxial woven roving E-glass fibre sheets. A series of FRP timber specimens, with different confinement lengths ranging from 0% to 70% of the span length of 5.4 m, were prepared and tested in three-point bending to present two equivalent cantilevers. A timber/FRP composite section with full confinement length was also investigated. Results showed that the FRP system, depending on the confinement length, provided a considerable improvement to the softwood regarding the load carrying capacity and bending stiffness. Theoretical calculation showed a good comparison to the experimental bending stiffness. Finally, finite element results showed satisfactory agreement with the experiments in terms of load carrying capacity and bending stiffness and failure modes.

A comparative study on the mechanical properties of laminated veneer lumber (LVL) produced from blending various wood veneers

Rotary veneers from spotted gum (Corymbia citriodora) and white cypress pine logs (Callitris glaucophylla) recovered from the native forest in Queensland, as well as Queensland plantation hoop pine (Araucaria cunninghamii) logs were used to manufacture LVL products following six different lay-up strategies including blended species LVL. The different lay-up strategies were to determine the opportunities for improving the mechanical performance of plantation softwood LVL by including native forest veneers. The manufactured products were evaluated for their bending performance, tension, bearing strength perpendicular to the grain, and longitudinal-tangential shear strength. The all-spotted gum LVL showed superior performance in all testing compared to other construction strategies. Blending even a small amount of spotted gum veneer with plantation hoop pine veneer resulted in improved mechanical performance, especially in flatwise bending. Opportunities exist to develop more optimised construction strategies that target specific product performances while optimising the use of the variable veneer qualities generated from log processing.

Accounting for biodiversity in life cycle impact assessments of forestry and agricultural systems—the BioImpact metric

Life cycle assessment (LCA) is a useful method for assessing environmental impacts at large scales. Biodiversity and ecosystem diversity are site-specific, often complex, and difficult to generalise within an LCA framework. There is currently no globally acceptable means of assessing biodiversity within the LCA framework. We introduce, test and revise BioImpact, a method for incorporating biodiversity into an LCA framework, on four production systems (native forestry, plantation softwood timber production, cropping and rangeland grazing) in Australia. Our proposed method, a metric we call BioImpact, incorporates biodiversity and ecological impacts through a series of semi-quantitative questions, published data and expert opinion which aim to encapsulate the main issues relating to biodiversity within a disturbance impact framework appropriate to LCA. Results are scaled to a single biodiversity measure that can be incorporated into LCA. We test and revise BioImpact scores on four production systems (native forestry, plantation softwood timber production, cropping and rangeland grazing) in comparison to species richness and net primary productivity (NPP) for these production systems. We demonstrate how the scores can be incorporated into LCA using SimaPro as a platform. For pine plantation, cropping/pastures and rangeland grazing, BioImpact demonstrated greater impact, which represents biodiversity loss for multiple species groups. Native forestry scored significantly lower impact than that of other land uses. As a comparison, all production processes scored highly for species richness of main multiple species groups (vascular plants, invertebrates, birds) and were not different in terms of NPP. Integration of BioImpact into LCA found that the softwood system, despite having a higher biodiversity impact per ha year, had a marginally lower BioImpact score per cubic metre compared to native forestry. This was possibly due to cumulative effects and consideration of the reference benchmark, e.g., low levels of pre-harvest biodiversity when not established on native forests; fewer threatened species (and lesser impact) compared to native forestry; questions not weighted sufficiently; and the difference between establishment on either agricultural cleared land or native forest area. Improvement in scaling and/or weighting within the BioImpact scores within each question is discussed. BioImpact encapsulates different components of biodiversity, is transparent, easily applied (subject to literature/ecological experts) and can be incorporated into LCA. Application of BioImpact for LCA requires co-ordination to identify key regions and production systems; develop the relevant scores with the assistance of ecologists; and make the results available in public LCA databases.

Out-of-grade sawn pine: A state-of-the-art review on challenges and new opportunities in cross laminated timber (CLT)

Abstract Plantation softwood is the future timber material resource for building and construction. However, significant volumes of sawn softwood are considered out-of-grade and sold at a loss. New approaches and methods need to be implemented to value-add out-of-grade timber and increase structural yield from existing plantations. This paper provides a critical review of out-of-grade characteristics of pine timber to gain an understanding of the strengths and weaknesses of this resource as a structural building material. Methods to incorporate out-of-grade timber into current building systems are presented and building technologies that can facilitate this use are identified. Finally, it discusses developments and important considerations for design of cross laminated timber (CLT) as a prime example of a building system with good capacity to incorporate high volumes of out-of-grade timber. This provides critical information for the maximum utilisation of sawn out-of-grade pine and is anticipated to create new opportunities that can effectively incorporate this renewable and sustainable material resource into innovative building systems and technologies.

Pinewood pyrolysis occurs at lower temperatures following treatment with choline-amino acid ionic liquids

Pinewoods are the dominant species in Australian softwood plantations and an important source of renewable lignocellulosic biomass. This work examines interactions between cholinium amino acid (Ch[AA]) ionic liquid (IL) – Water mixtures and pinewood. The Ch[AA] ILs employed were cholinium arginate (Ch[Arg]), cholinium glycinate (Ch[Gly]), and cholinium aspartate (Ch[Asp]), with water contents between 32 and 42 wt%. Pinewood and Ch[AA] ILs were mixed at 90 °C for all samples, and also 120 °C for Ch[Arg], as it dissolved the most biomass at 90 °C. Thermogravimetric analysis (TGA), scanning electron microscopy (SEM), x-ray diffraction (XRD), and compositional (CHNS) analysis were performed on the raw and treated biomass samples to reveal the changes in physical and chemical properties. While Ch[Arg] solubilised the greatest mass of biomass during treatment, the most pronounced changes in decomposition properties was obtained using Ch[Gly]. The TGA analysis revealed the maximum in the derivative weight loss data shifted to lower temperatures by 29 °C.