Soaking Treatment Research Articles

Effect of Treating Alfalfa Seeds with Gibberellin and Nano-fertilizer on Productive Characteristics and Protein Content in Hydroponic Cultures

This study was carried out in an experiment in an incubator designed for hydroponic seed germination with tight thermal insulation in the laboratories of the Department of Plant Production Technologies at the Technical College of Agriculture in Mosul, which is affiliated with the Northern Technical University in Iraq, where the seeds of the Dutch variety alfalfa (Medicago sativa. L) were germinated commercially and four times between 2022 and 2024. The experiment was carried out in a completely randomized design (CRD) with two factors and three replicates in perforated dishes with dimensions of 28 cm in length and 19 cm in width (area 532 cm2) at a seed rate of kg / m2, resulting in an average seed weight of 53 g in one dish. The first experimental factor was the germination periods, while the second factor was soaking the seeds in solutions of varying amounts made from gibberellin and nano-compound fertilizer with the comparison treatment, which is soaking in water alone, as follows: Gibberellin 100 ppm and given the symbol GA 100ppm- Gibberellin 200 ppm and given the symbol 200ppm GA- --Nano fertilizer 20:20:20 NPK at a concentration of 2000 ppm and given the symbol NPK2000ppm. -Nano fertilizer 20:20:20 NPK at a concentration of 4000 ppm and given the symbol NPK4000ppm. This study showed that the Gibberellin 200ppm GA treatment was significantly superior to the rest of the other soaking treatments in the characteristics of the height of the incubator (3.66 cm), as well as the wet weight of both seedlings and roots and their dry weight, which were (497.88, 56.97g/dish-1), respectively, The fresh and dried root weights were considerably greater in the same treatment, at (400.86 and 43.86 g/dish-1), respectively. while the comparison treatment was superior. Morally, it was significantly superior to the rest of the other soaking treatments in the characteristic of protein in the medium was (18.29%). As for the times of hydroponic seed germination, there were no significant differences between the times in all the studied characteristics, which enhances the high degree of incubator isolation, the accuracy of implementing the experiment, and the accuracy of taking the results.

Development of Cashew and Pistachio Ladders through a Food-Processing Approach.

Following successful oral immunotherapy (OIT) for peanut allergy using boiled peanuts (BOPI trial), this study investigated the potential of wet-thermal-processing-induced allergen modification, specifically soaking and boiling (1-4 h) to reduce the allergenicity of cashew and pistachio allergens. In addition, this study provides a foundation of understanding for developing safer forms of cashew/pistachio administration for application in OIT by gradual exposure to increasing doses of modified allergens with reduced potency as an "allergen ladder". An SDS-PAGE analysis and an intrinsic-fluorescence spectroscopy revealed altered tertiary structures of the allergens, leading to their denaturation and even degradation. Notably, the reduction in both allergen-specific polyclonal IgG and human-specific IgE (sIgE) binding correlated with the treatment time, with the most significant decrease observed after 4 h of boiling. In contrast, shorter soaking treatments showed negligible effects on the IgE-binding capacity of these nuts, therefore indicating a further need for optimization. These findings indicate that extended boiling effectively reduced the amounts of the highly potent allergenic component Ana o 3 in cashew and Pis v 1 in pistachio, as confirmed by ELISA using polyclonal anti-Ana o 3 antibodies, and an immunoblot showed decreased IgE epitope binding in cashew and pistachio allergens, which further modified their allergenic profiles. This approach shows promise as a viable method for offering a safer therapeutic option for cashew/pistachio allergy.

Soaking Water Of Pineapple Peel (Ananas comocus L. Merr) Solution On Reducing Formaldehyde Levels In Salted Fish

ABSTRACT Formaldehyde in salted fish processing is used to extend the shelf life of salted fish, potentially causing harmful effects on health. Before processing, such as soaking using pineapple peels can be done to reduce formaldehyde levels so that it is not harmful to health. The purpose of the study was to determine the decrease in formaldehyde levels in salted fish before and after soaking using a pineapple peel solution. This research is a pre-experimental study with a group Pretest and Posttest Design. The object of research is salted fish soaked in pineapple peel solution concentrations of 20%, 40%, 60%, and 80% with 4 replications. Soaking time is done for 60 minutes. The method of checking formaldehyde levels using the spectrophotometer method. The data that has been obtained is then analyzed using a paired t-test. The results of the examination of formaldehyde levels of salted fish before soaking amounted to 13.30 mg/kg. In contrast, after soaking the pineapple peel solution concentration of 20%, 40%, 60%, and 80% respectively amounted to 6.58 mg/kg, 4.16 mg/kg, 0.15 mg/kg, and 0.11 mg/kg, and tap water of 8.14 mg/kg. The Paired t-test obtained the P < α (0.05), meaning there is a significant difference in decline. The highest formaldehyde content reduction of 99.14% occurred in the treatment of soaking in pineapple peel solution with a concentration of 80% with a soaking time of 60 minutes. There is a significant difference between formaldehyde levels in salted fish before and after soaking using a pineapple peel solution. The use of pineapple peel solution can be an alternative effort in reducing formaldehyde levels in salted fish before processing for consumption and using other fruit peels with different concentration variations and different soaking times in salted fish.

Multi-scale evaluation of surfactant effects on asphalt desorption behavior from oil sand surfaces

This study created a hydrophobic oil sand model to investigate the impact of surfactants on the desorption behavior of asphalt from solid surface. Cationic surfactant cetyl trimethyl ammonium bromide (CTAB) and anionic surfactant sodium dodecyl benzene sulfonate (SDBS) were used to soak the model to observe the effect of surfactants on asphalt desorption. The effect of surfactant pretreatment on the wettability of the substrate was evaluated by measuring the contact angle of ultrapure water on the substrate and observing the morphological changes of the solid surface by atomic force microscopy. The results show that the contact angle of the model treated with SDBS decreases to 10° after 3 days, which significantly improves the wettability of the substrate surface and promotes the desorption of asphalt. However, CTAB has no obvious effect on asphalt desorption. The standard deviation of the gray value of the sand surface image is significantly reduced to 38.693 after the SDBS treatment, which can be seen by binarizing the image. This suggests that the asphalt and solution are evenly distributed and that there is hardly any discernible boundary. Nevertheless, neither of the two surfactants can improve the water-based extraction efficiency of oil sands after soaking treatment. The asphalt yield is less than 5% after 30 days of pretreatment with CTAB solution, while only 45% asphalt yield is obtained after 30 days of pretreatment with SDBS solution. Despite these variations, the quality of asphalt foam remains relatively the same. This may be related to the failure of surfactants to improve the surface wettability of hydrophobic sand. Therefore, the surface wettability of the sand is considered to be a key factor affecting the asphalt desorption and final yield. This study can provide a scientific basis for oil sand recovery to a certain extent.

Optimizing multi-recycled concrete for sustainability: Aggregate gradation, surface treatment methods and life cycle impact assessment

Utilizing demolished waste as recycled aggregate in concrete is a sustainable practice, however, the concerns over inconsistent quality, such as hardened mortar content and water absorption, hinder global adoption. This study evaluates the physical, microstructural properties and gives insights into Life Cycle Impact Assessment of three generations of recycled aggregate concrete. The microstructure analysis yielded compelling insights into the role of Interfacial Transition Zone (ITZ) of reclaimed aggregate on concrete. The study demonstrated that the effective proportioning of coarse and fine aggregate particles using Compressible Packing Model (CPM), resulted in a reduction of dosage of cement in concrete volume, reducing the Binder Intensity Index (BII), and an improvement in the strength and stability of concrete. Additionally, surface treatment methods, including water soaking, mechanical, and thermo-mechanical treatments, were explored. The thermo-mechanical treatment method proved to be effective in reducing 40–60 % of residual mortar. Life cycle assessment of treated and untreated recycled aggregate concrete was performed, considering five environmental impact indicators viz., Global Warming Potential (GWP), Acidification Potential (AP), Eutrophication Potential (EP), Abiotic Depletion Potential (ADP) and Human Toxicity (HT). These indicators illustrated that CPM method of mix proportioning accompanied with thermo-mechanical treatment of repurposed aggregate resulted in lowering environmental impact. These findings underscore the potential for sustainable concrete construction through the use of treated recycled aggregate, offering valuable insights into methods for augmenting its quality and performance.

Regulation of seed soaking with indole-3-butyric acid potassium salt (IBA-K) on rapeseed (Brassica napus L.) seedlings under NaCl stress

The growth and yield of rapeseed are significantly hampered by salt stress. Indole-3-butyric Acid Potassium Salt (IBA-K) has been found to alleviate the impact of salt stress on plant growth. However, the regulatory effect of IBA-K dipping on salt-stressed rapeseed remains unclear. To explore the implications of IBA-K on the growth and development of rapeseed during the seedling stage, we conducted potting experiments using the Huayouza 62 variety. Five different concentrations of IBA-K for seed soaking (0, 10, 20, 40, 80 mg·L− 1) were tested. The promotional impact of IBA-K on rapeseed demonstrated an initial increase followed by a decline, reaching a peak at 20 mg·L− 1. Therefore, 20 mg·L− 1 was determined as the optimal concentration for subsequent experiments. To further understand the mechanism of IBA-K’s action on salt-stressed rapeseed seedlings, we utilized the moderately salt-resistant cabbage rapeseed variety Huayouza 158R and the highly salt-resistant Huayouza 62 as specimens. The investigation focused on their response and repair mechanisms under 150 mmol·L− 1 NaCl stress. The findings demonstrated that compared with the sole NaCl stress, the 20 mg·L− 1 IBA-K seed soaking treatment under salt stress significantly enhanced the plant height, stem diameter, and leaf area of both rapeseed varieties. It also led to greater biomass accumulation, increased chlorophyll content, and improved photosynthetic efficiency in rapeseed. Furthermore, this treatment bolstered the activity of antioxidant enzymes such as superoxide dismutase (SOD), peroxidase (POD), and catalase (CAT), while significantly reducing the levels of electrolyte leakage (EL) and malondialdehyde (MDA). Consequently, it alleviated the membrane lipid peroxidation damage induced by NaCl stress, enhanced the accumulation of soluble proteins, maintained cellular osmotic pressure, and effectively mitigated the adverse effects of NaCl stress on rapeseed.

Effects of soaking treatment on water distribution of rice grains, starch characteristics and eating quality of wet rice noodles

Herein, rice was subjected to different soaking processes on water distribution of rice grains, starch characteristics, and eating quality of fresh wet rice noodles. Results demonstrated that, when soaked at temperatures between 10 °C and 40 °C for 120 min, rice grains reached saturation in water absorption, and the hardness gradually stabilized. However, the moisture continued to penetrate the interior of rice grains after 120 min, leading to an increase in moisture content, higher water permeability, and enlarged water migration channels. With extended soaking time periods, the content of damaged starch in rice flour considerably decreased. Although the gelatinization temperature of rice starch decreased after soaking, the enthalpy required for gelatinization increased. The relative crystallinity of rice starch demonstrated an increasing trend, followed by a decreasing trend, and reached its highest value of 18.18 % after 60 min of soaking. To summarize, the texture indices of fresh rice noodles demonstrated an increasing trend, although stretching and cooking quality demonstrated a trend of initially increasing and then decreasing with no considerable changes observed between 120 and 240 min of soaking. In summary, moderate soaking treatment can enhance the edible quality of fresh wet rice noodles.

Pengaruh Air Kelapa, Ekstrak Bawang Merah dan Ekstrak Rebung Bambu Terhadap Perkecambahan Benih Kopi Robusta (Coffea canephora)

Background: Robusta (Coffea canephora) is one type of coffee widely cultivated in Indonesia and is one of the leading commodities. Coffee seeds include seeds that have a long dormancy period that inhibits the germination process. Breaking dormancy can be done by several methods, one of which is soaking in natural growth regulators. Soaking treatment with natural growth regulators can be combined with soaking time treatment to break dormancy. This study aimed to determine the combination of natural growth regulator treatment and the right soaking time for Robusta coffee seed germination. Methods: This research is a 3-repeat Complete Factorial Randomized Design Experiment with the first factor of natural growth regulators type, which consists of 4 levels, namely: Z0 = control; Z1 = coconut water; Z2 = onion extract and Z3 = bamboo shoots, and the second factor is the length of soaking which consists of 3 levels, namely P1 = 12 hours; P2 = 24 hours and P3 = 36 hours. Results: Natural growth regulators' treatment of shallot extract with 24 hours of soaking time gave the best results on all parameters. Conclusions: Using natural growth regulators from coconut water, shallots, and bamboo shoots with several soaking times affects all parameters observed, both in single and combined administration.

Effect of Heat Treatment, Water and Vinegar Soaking on Protein and Phytic Acid Levels in Hemp Seed Meal

Hemp plants are notable for their climate resilience, and hempseed meal (HSM) is a potential high-protein feed for poultry. However, HSM has high levels of the antinutritional factor phytic acid (PA). This study aimed to evaluate the effects of heat and soaking treatments on the protein and PA content of HSM. HSM was obtained through cold pressing of whole hempseed and then subjected to heat treatment at 70°C for 24 hours. Soaking treatments involved water, water-vinegar mix, and vinegar for 1, 7, and 24 hours, followed by drying and analysis of PA and protein content. Results indicated that heating increased PA content without affecting protein levels. Soaking duration did not significantly alter protein content but did affect PA levels, with 24-hour soaking significantly increasing PA compared to 1-hour and 7-hour durations. The soaking material also influenced PA content: water soaking increased PA, while a 1-hour vinegar-water mix and 7-hour vinegar soaking significantly reduced PA. The highest PA concentration occurred with 24-hour water soaking. The protein content was highest with 7-hour vinegar soaking. In conclusion, acidic soaking solutions, particularly vinegar and vinegar-water mix, effectively reduced PA in HSM without protein loss.

Crafting and analyzing nonwovens enhanced with antimicrobial metal particles and diverse mechanisms via substitution reaction

Bacterial infections result in serious impacts on human health. Non-toxic, potent, and flexible antimicrobial particles loaded onto nonwoven materials offer a promising solution. Metallic antimicrobial particles have achieved significant attention and application; however, common materials such as silver and copper exhibit potential toxicity and typically employ a singular antimicrobial mechanism. This limitation can diminish their effectiveness over the service cycle. In our research gallium (Ga), known for its activity and versatile antimicrobial mechanisms, was employed with ferrous ions (Fe2+), which offer broad-spectrum antimicrobial properties and lower potential toxicity compared to silver and copper. Through spontaneous substitution reaction. Ga and Fe2+ can generate Ga–Fe alloys and various antimicrobial particles. In this study, we developed antimicrobial nonwovens by loading them with multiple types of metal antimicrobial particles through a simple soaking and surface treatment process. The multifaceted antimicrobial mechanisms introduced by these multiple particles provide the nonwoven materials with exceptional antimicrobial performance, achieving an effectiveness of up to 99.99 % against Escherichia coli and Staphylococcus aureus. The feasibility of the substitution reaction between Ga and Fe2+ was thoroughly verified through theoretical calculations, X-ray photoelectron spectroscopy (XPS) characterization, and experimental observations. This research offers valuable insights for advancing and exploring antimicrobial nonwoven materials.

Effect of acid soak treatment of the precursor on the structure and properties of polypropylene-based carbon fibers

Polyolefin fibers have received wide attention as the precursor for low-cost carbon fiber, and cross-linking of linear polyolefin by strong acid has been proven to be an effective way to stabilize the precursor fiber prior to carbonization. However, the conventional temperature used in sulfonation process is too high and could result in severe decomposition of the linear chain of the polymer, which further deteriorated the mechanical properties of the as-prepared carbon fiber. Thus, reducing the duration of sulfonation process operated at high temperature may alleviate the degradation behavior, conferring the polyolefin-based carbon fibers with better performance. In this paper, polypropylene (PP) fibers were soaked in sulfuric acid at 50 °C–90 °C, before the conventional preparation protocol of PP-based carbon fiber. The structural evolution from PP to carbon fiber were characterized by Differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and Raman spectroscopy. The mechanical and conductive properties of carbonized fibers where further measured. The results showed that the soak in sulfuric acid resulted in swelling of PP fibers in diameter direction, as well as reducing the crystallinity of the fibers, both of which were physical transformation, and could be easily controlled by soak temperature. The subsequent sulfonation at conventional temperature was fastened for the soaked PP fibers, and the duration of sufficient sulfonation were almost reduced by half. The obtained carbon fibers exhibited better thermal conductivity and mechanical properties, which were enhanced by 25 % and 40 %, respectively, compared with that without soak pretreatment.

Eliminating leaf scald disease in sugarcane: efficacy of hot water and cold soak treatments

Eliminating leaf scald disease in sugarcane: efficacy of hot water and cold soak treatments

Direct Anchoring of Molybdenum Sulfide Molecular Catalysts on Antimony Selenide Photocathodes for Solar Hydrogen Production.

Molybdenum sulfide serves as an effective nonprecious metal catalyst for hydrogen evolution, primarily active at edge sites with unsaturated molybdenum sites or terminal disulfides. To improve the activity at a low loading density, two molybdenum sulfide clusters, [Mo3S4]4+ and [Mo3S13]2-, were investigated. The Mo3S x molecular catalysts were heterogenized on Sb2Se3 with a simple soaking treatment, resulting in a thin catalyst layer of only a few nanometers that gave up to 20 mA cm-2 under one sun illumination. Both [Mo3S4]4+ and [Mo3S13]2- exhibit catalytic activities on Sb2Se3, with [Mo3S13]2- emerging as the superior catalyst, demonstrating enhanced photovoltage and an average faradaic efficiency of 100% for hydrogen evolution. This superiority is attributed to the effective loading and higher catalytic activity of [Mo3S13]2- on the Sb2Se3 surface, validated by X-ray photoelectron and Raman spectroscopy.

Synthesis of Carboxyl-Functionalized COFs with Alternate Stable β-Ketoenamine and Benzimidazole Linkages: Unraveling Exceptional Solvent Effects for Efficient Uranium Separation.

The prevalent π-π interactions in 2D covalent organic frameworks (COFs) impart a certain flexibility to the structures, making the stacking of COF layers susceptible to external stimuli and introducing some structural disorder. Recent research indicates that the flexibility between COF layers and the associated disorder significantly influence their selective adsorption performance toward gas molecules. However, the adsorption process in a solution environment is more complex compared to gas-phase adsorption, involving interactions between adsorbents and adsorbates, as well as the solvation effects of flexible 2D COFs. Therefore, the inherent flexibility and disorder in 2D COFs under solution conditions and their impact on the adsorption performance of metal ions have not been observed yet. Herein, the synthesis of a novel carboxyl-functionalized COF featuring stable β-ketoenamine and benzimidazole linkages, named DMTP-COOH, is presented. DMTP-COOH exhibits excellent selective adsorption capability for uranium, with significantly different adsorption capacities observed after treatment with different solvents. This notable difference in adsorption capacity is observed under varying pH, concentration, time, and even in the presence of multiple competing ions. This work represents the first observation of the significant impact of solvent soaking treatment on the selective adsorption performance of COFs for uranium under liquid conditions.

Engineering shrinkage resistance of nano-structured hydrogels in seawater for fast uranium capture

Synthetic hydrogels, which are 3D networks composed of crosslinked hydrophilic polymer chains, have been created using various crosslinked ways for uranium capture due to full exposure of chelate functional groups. However, the conventional honeycomb-like hydrogels exhibit non-connected micropore structure, which locks abundant water molecules and hence is unfavorable for mass transfer. Herein, we demonstrate a simple synthesis of the nano-structured hydrogel with activated nanogels as nano-crosslinkers (denoted as PGP hydrogel), and probe into the relationship between hydrogel structural parameters and uranium adsorption kinetics. It is found that the PGP hydrogel with a low crosslinking density of ∼0.02 mol/m3 possesses interconnected micropores, thereby facilitating diffusion of uranyl ions (UO22+) in 3D polymeric networks. Furthermore, a freeze-assisted soaking strategy is proposed to endow PGP hydrogel (denoted as target hydrogel) with strong shrinkage resistance in natural seawater, resulting in a ∼40 % increase in water permeance to reach 369 Lm−2h−1MPa−1. Correspondingly, the adsorption equilibrium time is shortened to ∼11 days. Although the uranium uptake capacity of PGP hydrogels with and without freeze-assisted soaking treatment remain basically unchanged (∼9.73 mg-U/g-Ads), a high uranium adsorption rate of 0.88 mg/g/d for the target hydrogel surpasses most currently available polymer adsorbents. The presented strategy is generalizable to a broader range of applications involving the adsorption of economically valuable ions in seawater or brine lake.

Enhanced superhydrophobicity and durability of modified cotton cloth for efficient oil-water separation

The development of simple, low-cost, and efficient oil/water separation membranes is still a major challenge in the field of wastewater treatment. In this study, an oil/water separation membrane is prepared based on low-cost cotton cloth (CF) through a simple solution soaking treatment without using organic solvents. Pristine CF is treated first with concentrated alkali and then chemically grafted by sodium methyl silicate (SMS) onto the surface to obtain oil/water separation membrane (SMS-O-CF). This process not only increases the roughness of the CF but also endows the surface with superhydrophobicity due to the outward extension of methyl groups, resulting in a water contact angle (WCA) of 155° and good self-cleaning ability. The SMS-O-CF achieves efficient separation for various oil/water mixtures and maintains a separation efficiency up to 96 % and a flux of over 11,557 L·m−2·h−1 after 220 cycles under neutral conditions. Moreover, the modified CF also exhibits excellent acid/alkaline resistance and wear resistance. Regardless of the 12 h acid/base immersion, 100 min water wash, or 200-cycle mechanical abrasion, SMS-O-CF still exhibits high flux and separation efficiency. Raw material cost for preparing SMS-O-CF is as low as 1.0 dollar/m2. The preparation of SMS-O-CF has provided a green manufacturing method for developing low-cost and efficient oil–water separation membranes.

Aqueous PEIE Soaking on ZnO for Ultraviolet Light Activation-Free Organic Photovoltaic Modules.

Ultraviolet (UV) light is typically needed to activate inverted organic photovoltaics (OPVs) with zinc oxide (ZnO) as electron transporting layer (ETL)for higher efficiency. However, UV light is a major cause for the degradation of organic active layers in OPVs. This is a contradiction that UV light activation enhances the efficiency but UV illumination deteriorates the stability. It is important to solve this contradiction to develop UV light activation-free OPV devices. Herein, a method of aqueous polyethylenimine ethoxylated (PEIE) soaking on ZnO is reported to realize UV light activation-free OPV devices. The S-shape in current density-voltage (J-V) characteristics of devices tested without UV light activation is eliminated through the treatment of aqueous PEIE soaking on ZnO. The treatment reduces the oxygen adsorbates, which is confirmed by Kelvin probe and X-ray photoelectron spectroscopy. A 10.08 cm2 organic photovoltaic module with the treated ZnO asETL showed high photovoltaic performance: VOC = 5.68 V, JSC = 2.7 mAcm-2, FF = 75.1%, and POutput = 11.5 mWcm-2 tested with the UV filter (light intensity of 0.788 sun). UV light activation is not needed for the modules to obtain high efficiency.

Sulfur-modified polyurethane adhesives: Green synthesis process and disassembly-responsive characteristics

Polyurethane adhesives have been widely used in industrial production and daily life for their excellent properties. With the urgent need for social progress, the intelligent responsiveness of polyurethane adhesives has become more and more important. Here, we demonstrate a stimulus-responsive polyurethane adhesive. Starting from the structural design, sulfur (S8) is added into the polyurethane adhesive for the first time using the inverse vulcanized mechanism, and the controllable disassembly response of the polyurethane adhesive under the condition of thermal stimulation is realized. In addition, the stimulus response of the adhesive can also be activated through the permeation process of methoxide anion (CH3O−), and the rapid disassembly response property is displayed in the methanol solution of CH3ONa, to realize the recovery of the bonding substrate. Simultaneously, the implementation of the inverse vulcanized mechanism imparts the adhesive with a diminished water absorption swelling rate and heightened cross-link density. On the surface of the metal substrate, it shows excellent bonding properties, with a lap shear adhesion strength reaching 2.8 MPa. It is worth noting that the adhesive also exhibits excellent underwater durability. After 36 h of underwater soaking treatment, its adhesion can still be maintained at 2.4 MPa. This work reveals the mechanism of rapid disassembly of polyurethane adhesives at the molecular level. By density functional theory (DFT) calculation, it is found that the minimum bond energy of the S-S bond in a polyurethane adhesive system is 134 KJ·mol−1, and the disassembly response can be triggered by heating to 53.79℃. At the same time, the mechanism of the disassembly response induced by CH3O− is further analyzed using an electrostatic potential (ESP) diagram. This work utilizes sulfur (S8) and castor oil (CO) as raw materials, which can be sourced from industrial or agricultural by-products. It breaks away from traditional polyurethane adhesive preparation methods and offers a "green" strategy that can be synthesized through a solvent-free one-pot process, thus providing a new way of thinking about obtaining sustainable polymers from industrial and agricultural by-products.

Effect of electric cooker soaking temperature on palatability of cooked aged indica rice

Based on sensory evaluation and texture characteristics, the improving effect of soaking temperature adjustment in an electric cooker on the palatability of cooked aged indica rice was investigated. The water content and distribution, starch gelatinization, and crystal structure of aged rice grains were analyzed at different soaking temperatures. The results demonstrated that soaking aged indica rice at low temperatures (25 °C and 40 °C) and high temperature (70 °C) increased hardness and reduced viscoelasticity, which were not conducive to achieving desirable sensory qualities. Conversely, soaking treatment at 50 °C positively impacts the palatability of aged indica rice. This treatment increased the proportion of structural water in aged rice grains to 6.38% and reduced starch crystallinity to 22.61%, thereby facilitating starch gelatinization and promoting the formation of desirable taste during subsequent cooking stages. Microstructural analysis revealed that soaked aged indica rice exhibited increased water absorption rates and more uniform distribution of moisture. These findings provided valuable insights for optimizing the cooking process of aged indica rice using the electric cooker.

MODIFICATION OF WOVEN DENDROCALAMUS ASPER IN COMPOSITE APPLICATIONS

The aim of this study is to examine the influence of immersing Petung Bamboo in a NaOH solution on the tensile strength (TS) of composites containing an epoxy matrix. Petung Bamboo Webbing was given 0%, 3%, 6% and 9%, soaking treatment. The Composite utilised in this investigation was fabricated by the Vacuum Assisted Resin Infusion technique. Tensile testing of composites is conducted according to the ASTM D638-1 standard. The findings indicated a positive correlation between the concentration of NaOH immersion and the adhesion between the woven surface of Petung Bamboo and the matrix. Consequently, the TS of the Composite was enhanced. However, increasing the concentrations beyond a certain point leads to more degradation of the lignin and cellulose in the fibers, resulting in a loss in the strength of the composite. The Petung Bamboo woven reinforced Composite achieved the highest TS of 136.06 MPa after being treated with a 6% NaOH immersion. This was followed by a 3% NaOH immersion treatment resulting in a TS of 106.04 MPa. Without any NaOH immersion treatment, the composite had a TS of 97.31 MPa. The lowest TS of the composite was observed after a 9% NaOH immersion treatment, measuring 90.79 MPa. The Petung Bamboo wicker-reinforced composite with NaOH immersion treatment showed higher fiber pullout and fiber-matrix debonding failures, while higher NaOH treatment concentration reduced these failures.